input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:NG排出部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:NG排出部ｽﾄｯﾊﾟｰの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "補給部ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"ﾗﾍﾞﾙの端面がﾄﾚｲﾊﾟﾚｯﾄに隠れ無い事",
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈ着用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"60㎜",
"60㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ接続と立ち上げ",
"WorkItems": [
"3. PC画面が立ち上がったらNPM-GWのｱｲｺﾝをﾀﾞﾌﾞﾙｸﾘｯｸ",
"5. ｼｽﾃﾑ立ち上げ",
"1. ﾄﾚｲ本体とﾁｪｯｶｰを接続する",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝの立ち上げ",
"4.ﾁｪｯｶｰの電源BOXとｻｰﾎﾞSWをON"
],
"WorkPoints": [
"･ﾁｪｯｶｰ電源接続･ﾒｲﾝｴｱｰ接続･ｴｱｰ配管･ｺﾈｸﾀ大-TRAY･S ･･･内側 ･ｺﾈｸﾀ小-TRAY･P ･･･外側 各々接続",
"FM-2294",
"部署等を入力",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰでQRｺｰﾄﾞを読み取り",
"ﾊﾞｰｺｰﾄﾞ情報入力",
"PnP情報書込み",
"PnP情報書込み完了",
"ON",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰがUSBﾎﾟｰﾄに挿入されているのを確認する",
"ON",
"ﾄﾚｲﾌｨｰﾀﾞ本体の電源が入り待機状態になる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"1. 原点復帰を行う",
"1. 原点復帰を行う",
"3. 補給部にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"補給部ｶﾊﾞｰを閉じﾄﾚｲﾊﾟﾚｯﾄがﾏｶﾞｼﾞﾝｼｬｯﾀｰに当っている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.6㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.8㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出し部調整治具",
"Size": "",
"ToolOther": "FM-6646",
"WorkName": "TP軸原点登録",
"WorkItems": [
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6646",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸原点登録",
"WorkItems": [],
"WorkPoints": [
"ﾒｶｽﾄｯﾊﾟｰ端面",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.9㎜で投光1.0㎜で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整①",
"WorkItems": [
"1. ﾊﾟﾜｰONする",
"2. TL軸原点復帰を行う",
"3. 引き出部を原点位置から下段23Slot高さへ移動する"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"原点位置まで下降する",
"FM-2848治具が取付いて無い事を確認｡ﾚﾊﾞｰが回転して危険です",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意のこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘﾌﾄ上昇"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"1. ㉖のマガジンシャッターを開を押す",
"3. 引き出部側を基準に測定する"
],
"WorkPoints": [
"FM-1934を引き出部へ",
"A0",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"3. 引き出部側を基準に測定する"
],
"WorkPoints": [
"A0",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A 1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A 1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取外す事",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"5. 各治具を取り出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"5. 各治具を取り出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）"
],
"WorkPoints": [
"O/Rｾﾝｻが投光",
"㉙を矢印方向に当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1㎜"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "ﾛﾝｸﾞﾋﾞｯﾄ2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）"
],
"WorkPoints": [
"O/Rｾﾝｻが投光",
"㉙を矢印方向に当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する"
],
"WorkPoints": [
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "傾き無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｰｼﾞﾝｸﾞ",
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認"
]
} | {
"QualityItem": "ｴｰｼﾞﾝｸﾞ動作",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "12時間:ｴﾗｰ停止が無いこと",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ｴｰｼﾞﾝｸﾞ"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "ﾊﾞｰｼﾞｮﾝ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整"
],
"WorkTypes": [],
"Words": [
"ﾌﾟｰﾘｰ間の中央で測定",
"WETE-G002-A11"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "9.8N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認①",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):226㎜規格 :74N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"ﾅｯﾄ2か所を緩めて､調整ﾎﾞﾙﾄにてﾃﾝｼｮﾝ調整調整完了後､ﾅｯﾄ2か所にて固定する",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ(ﾅｯﾄ) 9.8N･m",
"締付ﾄﾙｸ(ﾅｯﾄ) 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整"
],
"WorkTypes": [],
"Words": [
"ﾌﾟｰﾘｰ間の中央で測定",
"㉚使用方法",
"WETE-G002-A11"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "59±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定",
"㉚使用方法"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6591",
"WorkName": "TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認②",
"WorkItems": [
"1. 各TP軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :12㎜ｽﾊﾟﾝ(S):80㎜規格 :59N±10%",
"引き出部ﾚﾊﾞｰ位置は(-)側のﾒｶｽﾄ位置である事",
"調整箇所",
"㉚のハンドルを青矢印方向に引き、㉚の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉚のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"橙丸ボルトを緩め、㉚にてテンション調整。完了後、締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TP軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"ﾌﾟｰﾘｰ間の中央で測定",
"㉚使用方法"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6591",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TP軸合ﾏｰｸ追加"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸合いﾏｰｸ追加",
"WorkItems": [
"1. TP軸を原点復帰する",
"2. 合いﾏｰｸを付ける"
],
"WorkPoints": [
"黄色ﾏｰｶｰ2ヵ所",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TP軸合ﾏｰｸ追加"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "合いﾏｰｸ記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの合いﾏｰｸが2箇所付いてること",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"調整治具"
]
} | {
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74±10%Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5052",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"調整治具"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5052",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ確認",
"WorkItems": [
"1. TL軸のﾍﾞﾙﾄ張力を確認"
],
"WorkPoints": [
"質量(M) :2.5g/㎜幅 (W) :15㎜ｽﾊﾟﾝ(S):88㎜",
"74N±10%",
"橙丸ボルトを緩め㉗を取付け緑丸の調整ボルトで調整する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ﾍﾞﾙﾄﾃﾝｼｮﾝ再調整",
"調整治具"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"4. 治具を取付ける"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整④",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(左右)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています",
"ﾊﾟﾜｰOFFにて締付の事",
"±0.05㎜以内(中央)±0.2㎜以内(左右)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"■安全作業",
"WETE-G002-A11"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"■3. ｶｯﾌﾟﾘﾝｸﾞを締付"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFにて締付の事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締付ﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑤",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑥",
"WorkItems": [
"1. ﾘﾌﾄ上下治具を取り外し",
"2. 下段23Slotから上段23Slotへ移動し高さ確認"
],
"WorkPoints": [
"下段23Slot調整後すぐには原点復帰は決して行わ無い事原点高さが変わる場合があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"上段23Slot",
"補給部",
"NG排出部",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"引き出部搬送面",
"ﾏｶﾞｼﾞﾝ側",
"FM-5519",
"FM-1934"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"上段23Slot",
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"補給部は内側を緩め調整",
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"±0.05㎜以内(中央部) ±0.2㎜以内(左右)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"上段23Slot",
"補給部",
"NG排出部",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"引き出部搬送面",
"ﾏｶﾞｼﾞﾝ側",
"FM-5519",
"FM-1934"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"上段23Slot",
"FM-1934",
"引き出部搬送面",
"WETE-G002-A11"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整⑦",
"WorkItems": [
"1. 引き出部と各段の高さを合わせる",
"2. 治具中央(A0)の高さに引き出部を基準に測定しながら合わせる"
],
"WorkPoints": [
"高さが合っていない場合は､各段の取付ﾈｼﾞ位置(左右同じ)",
"･上段23Slot ･NG排出部･補給部先に合わせた下段23Slotを含み4か所の高さを合わせていく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"上段23Slot",
"FM-1934",
"引き出部搬送面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞ",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞ",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TL軸ﾏｲﾅｽ側ｾﾝｻ確認",
"WorkItems": [
"1. ﾘﾌﾄを最下段の位置へ下げる",
"2.㉙をドグに取付け、 TL軸マニュアル動作にて 0.1㎜上昇させ、センサの位置調整を行う",
"3. TL軸を原点復帰し､ｾﾝｻの遮光を確認する",
"4. TL軸とｺﾞﾑｽﾄｯﾊﾟｰの干渉確認をする"
],
"WorkPoints": [
"O/Rｾﾝｻが投光すること",
"ﾎﾞｰﾙﾈｼﾞとｺﾞﾑｽﾄｯﾊﾟｰの干渉無い事",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意の事",
"O/Rｾﾝｻが遮光する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整",
"検査表①:TL軸ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"ｺﾞﾑｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙﾈｼﾞ",
"WETE-G002-A11"
]
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｽﾄｯﾊﾟｰとの干渉無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-①(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸をﾊﾟﾜｰONする",
"2. ﾄﾚｲ本体の原点復帰",
"3. 引き出部を連結位置へ移動",
"4. 引き出部をNG排出部へ高さ位置を合わす",
"5. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かす"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとする",
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [
"C~F間に0.3㎜のｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"LMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認",
"ｼｬｯﾀｰと治具の間(A,B)に0.05mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸のｽﾄﾛｰｸ確認",
"検査表①:引き出軸のｽﾄﾛｰｸ確認"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸のｽﾄﾛｰｸ確認",
"検査表①:引き出軸のｽﾄﾛｰｸ確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸のｽﾄﾛｰｸ確認",
"検査表①:引き出軸のｽﾄﾛｰｸ確認"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸のｽﾄﾛｰｸ確認",
"検査表①:引き出軸のｽﾄﾛｰｸ確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-②(ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. 治具を引き出部にｾｯﾄする",
"2. 治具とｱｰﾑ(ﾍﾞｱﾘﾝｸﾞ)の隙間を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸のｽﾄﾛｰｸ確認",
"検査表①:引き出軸のｽﾄﾛｰｸ確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにてﾍﾞｱﾘﾝｸﾞと平行だしｼﾞｸﾞの隙間調整を行う④両側の隙間調整完了後､橙色ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める左右同じように調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.3㎜",
"0.3㎜",
"0.3㎜",
"0.3㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.3㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにてﾍﾞｱﾘﾝｸﾞと平行だしｼﾞｸﾞの隙間調整を行う④両側の隙間調整完了後､橙色ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める左右同じように調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.3㎜",
"0.3㎜",
"0.3㎜",
"0.3㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにてﾍﾞｱﾘﾝｸﾞと平行だしｼﾞｸﾞの隙間調整を行う④両側の隙間調整完了後､橙色ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める左右同じように調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.3㎜",
"0.3㎜",
"0.3㎜",
"0.3㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにてﾍﾞｱﾘﾝｸﾞと平行だしｼﾞｸﾞの隙間調整を行う④両側の隙間調整完了後､橙色ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める左右同じように調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.3㎜",
"0.3㎜",
"0.3㎜",
"0.3㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-③(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整方法(長手方向)"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞﾞとｶﾞｲﾄﾞ平行出し治具の隙間を確認しながら調整",
"下記4個所でｼｯｸﾈｽｹﾞｰｼﾞが通るように調整する",
"調整箇所 左右各1個所",
"調整方法①橙丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにてﾍﾞｱﾘﾝｸﾞと平行だしｼﾞｸﾞの隙間調整を行う④両側の隙間調整完了後､橙色ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める左右同じように調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.3㎜",
"0.3㎜",
"0.3㎜",
"0.3㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行だし治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整",
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-④(高さ確認)",
"WorkItems": [
"1. TP軸の高さ調整を行う"
],
"WorkPoints": [
"①赤丸ﾎﾞﾙﾄを緩める②調整用ﾅｯﾄを緩める③調整用ﾎﾞﾙﾄにて高さ調整｡④赤丸ﾎﾞﾙﾄを締める⑤調整用ﾅｯﾄを締める※左右の高さ調整実施の事",
"寸法測定箇所",
"左右同じように調整する事規格値:12.5+0.5㎜",
"調整方法"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整"
],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ",
"調整ﾅｯﾄ",
"WETE-G002-A11"
]
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "12.5㎜~13.0㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [
"1. TP軸原点復帰を行う",
"3. 吸着位置でﾚﾊﾞｰの確認を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"4. ﾊﾟﾜｰをOFF",
"■5. TP軸ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの増し締め"
],
"WorkPoints": [
"ﾊﾟﾚｯﾄをｶﾞｲﾄﾞに当付ける",
"ﾊﾟﾚｯﾄをｶﾞｲﾄﾞに当付ける",
"t=0.4㎜のｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が確保されていること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄの締結ﾄﾙｸ",
"検査表①:引き出し部原点位置ｽﾄﾛｰｸ調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑤(TP軸ﾚﾊﾞｰ位置確認)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"再度動作をさせｾﾝｻの中心にあること",
"LEDが点灯のこと(赤緑)"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑥(ﾊﾟﾚｯﾄ検出ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾄﾚｲ本体のの原点復帰",
"2. 引き出部を連結位置へ移動",
"3. 引き出部をNG排出部へ移動",
"4. ﾊﾟﾚｯﾄ戻しへ移動",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻの光軸確認"
],
"WorkPoints": [
"ｾﾝｻの中心で投光状態であること",
"再度動作をさせｾﾝｻの中心にあること",
"LEDが点灯のこと(赤緑)"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "光軸確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻの中心に投光状態である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"3. 現在値の確認"
],
"WorkPoints": [
"『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が投光(水色)しているか確認",
"遮光(黒色)の場合はｾﾝｻｰを投光する位置に調整する",
"現在値 -100.000 (0.001㎜単位は無視) +0.33st -99.70 投光を確認 +0.47st -99.56 遮光を確認していく ﾏﾆｭﾋﾟﾚｰﾀｰ(+0.1㎜と+0.01㎜を使用)にて その数値の位置でﾁｪｯｶ―のｽﾃｰﾀｽを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"3. 現在値の確認",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動"
],
"WorkPoints": [
"現在値 -100.000 (0.001㎜単位は無視) +0.33st -99.70 投光を確認 +0.47st -99.56 遮光を確認していく ﾏﾆｭﾋﾟﾚｰﾀｰ(+0.1㎜と+0.01㎜を使用)にて その数値の位置でﾁｪｯｶ―のｽﾃｰﾀｽを確認する",
"『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が投光(水色)しているか確認",
"遮光(黒色)の場合はｾﾝｻｰを投光する位置に調整する",
"ｾﾝｻｰ",
"ﾈｼﾞを緩めﾌﾞﾗｹｯﾄを矢印方向に動かす",
"ﾄﾞｸﾞのｽﾘｯﾄ部分で投光にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑦(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1.ﾊﾟﾚｯﾄ戻し位置でﾁｪｯｶｰの『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が 投光(水色)しているか確認する",
"4. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.33st -99.670㎜位置へ移動",
"2. TP軸ﾏﾆｭｱﾙ動作を押す",
"3. 現在値の確認"
],
"WorkPoints": [
"『TP軸引き出位置(ﾏｶﾞｼﾞﾝ)』が投光(水色)しているか確認",
"遮光(黒色)の場合はｾﾝｻｰを投光する位置に調整する",
"現在値 -100.000 (0.001㎜単位は無視) +0.33st -99.70 投光を確認 +0.47st -99.56 遮光を確認していく ﾏﾆｭﾋﾟﾚｰﾀｰ(+0.1㎜と+0.01㎜を使用)にて その数値の位置でﾁｪｯｶ―のｽﾃｰﾀｽを確認する"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.33stで投光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色)になればOK･動作中『ﾊﾟﾚｯﾄ干渉領域です』のｴﾗｰがでますが 確認を押すと現在値がでます｡",
"LEDの消灯状態で移動させた場合下記警告画面が出る｡･この画面が出た場合動作しない為､下記の手順で TP軸を原点位置へ戻す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"2. ｾﾝｻの固定を行う",
"3. 一連の調整完了後､再度ｾﾝｻの投光･遮光を確認"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｽﾄﾛｰｸ調整-⑧(引き出位置ｾﾝｻ確認調整)",
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.47st -99.53㎜位置まで移動"
],
"WorkPoints": [
"-99.53で点灯の場合はｾﾝｻをﾏｲﾅｽ側(矢印側)へ動かし消灯させる 消灯位置は安定した状態になるよう少しづつ移動させる事",
"･+0.47st -99.66~-99.53㎜の間で遮光(黒色)になればOK･動作中『ﾊﾟﾚｯﾄ干渉領域です』のｴﾗｰがでますが 確認を押すと現在値がでます｡",
"LEDの消灯状態で移動させた場合下記警告画面が出る｡･この画面が出た場合動作しない為､下記の手順で TP軸を原点位置へ戻す事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.47stで遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする"
],
"WorkPoints": [
"矢印方向に当てつけ",
"矢印方向に当てつけ",
"矢印方向に当てつけ",
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1mm"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.