input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする"
],
"WorkPoints": [
"矢印方向に当てつけ",
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [],
"WorkPoints": [
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する",
"1. TP軸の原点復帰を行う",
"2. ﾘﾌﾄを上昇させる(吸着位置)",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出位置へ動かし､DOGに治具をｾｯﾄする"
],
"WorkPoints": [
"ﾏｲﾅｽ側O/Rｾﾝｻが-99.9㎜で投光､-100.0㎜で遮光するように調整(治具取付時)",
"矢印方向に当てつけ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出部(TP軸)原点位置ｽﾄﾛｰｸ調整"
],
"WorkTypes": [],
"Words": [
"0.2㎜(治具出代)",
"0.1mm",
"調整ﾎﾞﾙﾄ",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"2. 引き出部ｱｰﾑを吸着位置に動かす",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"矢印方向に当てつけ",
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾊﾟﾚｯﾄ出し",
"1.0㎜(治具出代)",
"0.1mm",
"検査表①:引き出部(TP軸)原点位置ｽﾄﾛｰｸ調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"3. 治具をDOGにｾｯﾄする",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.0㎜(治具出代)",
"0.1mm",
"検査表①:引き出部(TP軸)原点位置ｽﾄﾛｰｸ調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.0㎜(治具出代)",
"0.1mm",
"検査表①:引き出部(TP軸)原点位置ｽﾄﾛｰｸ調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. TP軸の原点復帰を行う",
"3. 治具をDOGにｾｯﾄする",
"2. 引き出部ｱｰﾑを吸着位置に動かす",
"4. TP軸を動作させｾﾝｻ位置を調整する"
],
"WorkPoints": [
"+側O/Rｾﾝｻが40.9㎜で投光､41.0㎜で遮光するように調整(治具取付時)",
"矢印方向に当てつけ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出部(TP軸)原点位置ｽﾄﾛｰｸ調整"
],
"WorkTypes": [],
"Words": [
"1.0㎜(治具出代)",
"0.1mm",
"ﾊﾟﾚｯﾄ出し",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "規定ｽﾄﾛｰｸで投光・遮光している事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. ﾄﾚｲ本体の原点復帰",
"2. 引き出部を連結位置へ移動",
"3.ｽﾄｯﾊﾟ位置の調整",
"4.TTL軸と引き出し連結部の隙間確認を行う"
],
"WorkPoints": [
"ｽﾄｯﾊﾟをTTL軸ﾌﾟﾚｰﾄに当てつけ",
"黄丸部分に0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"TTL軸ﾌﾟﾚｰﾄと連結部ｼｬﾌﾄ間",
"TTL軸ﾌﾟﾚｰﾄとｽﾄｯﾊﾟ間",
"接触面にはｸﾞﾘｰｽが塗布されているか確認の事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"TTL軸ﾌﾟﾚｰﾄ",
"ｽﾄｯﾊﾟ",
"検査表①:TTL軸のｽﾄﾛｰｸ調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [
"TTL軸ﾌﾟﾚｰﾄと連結部ｼｬﾌﾄ間",
"TTL軸ﾌﾟﾚｰﾄとｽﾄｯﾊﾟ間"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [],
"WorkPoints": [
"TTL軸ﾌﾟﾚｰﾄと連結部ｼｬﾌﾄ間",
"TTL軸ﾌﾟﾚｰﾄとｽﾄｯﾊﾟ間"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝをｾｯﾄする",
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"投光用",
"遮光用",
"上下段に挿入",
"確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"実際の治具色は同色です｡(ﾗﾍﾞﾙを確認)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝをｾｯﾄする",
"2. 治具をｾｯﾄする"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付ける",
"上下段に挿入",
"確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目",
"補給部に製品ﾊﾟﾚｯﾄを挿入し手でｶﾞﾀつかせた際､ｾﾝｻが不安定な動作をしないか確認する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目",
"補給部に製品ﾊﾟﾚｯﾄを挿入し手でｶﾞﾀつかせた際､ｾﾝｻが不安定な動作をしないか確認する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整①(ﾏｲﾅｽ側O/Rｾﾝｻ)",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う",
"2. ﾄﾚｲﾊﾟﾚｯﾄを補給段にｾｯﾄしｾﾝｻのﾁｬﾀﾘ確認を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目",
"補給部に製品ﾊﾟﾚｯﾄを挿入し手でｶﾞﾀつかせた際､ｾﾝｻが不安定な動作をしないか確認する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 45cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "−99.9㎜で投光−100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "TP軸ORｾﾝｻ位置調整GW用ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6661",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部②:NGﾊﾟﾚｯﾄ③:ﾏｶﾞｼﾞﾝ上最上段(1段目)④:ﾏｶﾞｼﾞﾝ下最上段(23段目)⑤:ﾏｶﾞｼﾞﾝ下最下段(23段目)",
"+1㎜",
"-1㎜",
"LEDが消灯(遮光)のこと→緑のみ",
"ｲﾝﾁﾝｸﾞにて±1㎜上下移動させても遮光しているのを確認",
"≪遮光確認≫･遮光確認位置において遮光しているのを確認 奇数段全てにﾊﾟﾚｯﾄ挿入≪投光確認≫･投光確認位置において投光しているのを確認 前段ﾊﾟﾚｯﾄ取り外し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6661",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部②:NGﾊﾟﾚｯﾄ③:ﾏｶﾞｼﾞﾝ上最上段(1段目)④:ﾏｶﾞｼﾞﾝ下最上段(23段目)⑤:ﾏｶﾞｼﾞﾝ下最下段(23段目)",
"+1㎜",
"-1㎜",
"LEDが消灯(遮光)のこと→緑のみ",
"ｲﾝﾁﾝｸﾞにて±1㎜上下移動させても遮光しているのを確認",
"≪遮光確認≫･遮光確認位置において遮光しているのを確認 奇数段全てにﾊﾟﾚｯﾄ挿入≪投光確認≫･投光確認位置において投光しているのを確認 前段ﾊﾟﾚｯﾄ取り外し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸ｾﾝｻｰ位置調整②(ﾌﾟﾗｽ側O/Rｾﾝｻ)",
"WorkItems": [
"2. 原点復帰を行う",
"3. ﾘﾌﾄ吸着位置へ上昇する",
"4. 補給位置へ1段下降させる",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"確認位置①:補給部②:NGﾊﾟﾚｯﾄ③:ﾏｶﾞｼﾞﾝ上最上段(1段目)④:ﾏｶﾞｼﾞﾝ下最上段(23段目)⑤:ﾏｶﾞｼﾞﾝ下最下段(23段目)",
"+1㎜",
"-1㎜",
"LEDが消灯(遮光)のこと→緑のみ",
"ｲﾝﾁﾝｸﾞにて±1㎜上下移動させても遮光しているのを確認",
"≪遮光確認≫･遮光確認位置において遮光しているのを確認 奇数段全てにﾊﾟﾚｯﾄ挿入≪投光確認≫･投光確認位置において投光しているのを確認 前段ﾊﾟﾚｯﾄ取り外し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが-99.9㎜で投光、-100.0㎜で遮光",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"3. ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押す",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"6. ﾊﾟﾚｯﾄを引き出部上に引き出す",
"7. B1306 ﾊﾟﾚｯﾄ引き出確認が無しの事"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "支持部にｸﾞﾘｰｽが塗布されている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っかかりや異音の発生及び偏摩耗が無いか確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-①",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っかかりや異音の発生及び偏摩耗が無いか確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "点灯確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが不安定な動作をし無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "45cN･m",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "16㎜赤消灯、緑点灯",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾊﾟﾚｯﾄｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5241",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ調整-②",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻ位置調整を行う"
],
"WorkPoints": [
"凹部17㎜時→LED赤緑点灯",
"凹部16㎜時→LED赤消灯 緑点灯",
"ｽﾛｯﾄ確認位置→補給部､上段23段目､下段23段目"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認",
"検査表①:ﾊﾟﾚｯﾄはみ出し検出PHの確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5241",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "17㎜赤点灯、緑点灯",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認①",
"WorkItems": [
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認①",
"WorkItems": [
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 原点復帰を行う",
"5. TL軸を動作し検出ｾﾝｻを確認する",
"1. 全段(奇数段)､補給段､NG排出段にﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする"
],
"WorkPoints": [
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ",
"LEDが消灯(遮光)のこと→緑のみ"
],
"Tolks": [],
"InspectionNo": "WETE‐G002‐A11",
"InspectionItems": [
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認",
"検査表①:ﾊﾟﾚｯﾄ有無検出ｾﾝｻ確認"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "遮光状態である事",
"Method": "目視",
"RecordMethod": "WETE‐G002‐A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻ確認②",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる",
"2. 原点復帰を行う",
"5. ﾏｶﾞｼﾞﾝ上段1段目へﾘﾌﾄを下げる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾊﾟﾚｯﾄ",
"Size": "",
"ToolOther": "MTKA010132AA",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻ確認②",
"WorkItems": [
"1. 引き出部有無検出ｾﾝｻの動作を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "有無確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが設定通り動作する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"WorkItems": [
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っかかりや異音の発生及び偏摩耗が無いか確認",
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っかかりや異音の発生及び偏摩耗が無いか確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"WorkItems": [
"1. ﾏｶﾞｼﾞﾝ(ﾄﾚｲﾊﾟﾚｯﾄ入り)をｾｯﾄする",
"2. TL軸･TP軸のｽﾋﾟｰﾄﾞを高速に切替",
"3. ｻｲｸﾙ指定回数に『4』を入力する",
"4. ｻｲｸﾙ数指定起動を押す"
],
"WorkPoints": [
"NG排出部及びﾏｶﾞｼﾞﾝの奇数段にﾄﾚｲﾊﾟﾚｯﾄがｾｯﾄされていること",
"補給位置､NGﾊﾟﾚｯﾄ位置及びﾏｶﾞｼﾞﾝ全段数について全段数確認する事",
"高速になっている事を確認",
"動作中にﾊﾟﾚｯﾄの引っかかりや異音の発生及び偏摩耗が無いか確認"
],
"Tolks": [],
"InspectionNo": "WETE‐G002‐A11",
"InspectionItems": [
"検査表①:ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "搬送確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "引っ掛かり/異音が無い事",
"Method": "目視",
"RecordMethod": "WETE‐G002‐A11",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立①",
"WorkItems": [
"1. STAND に①を圧入する",
"◆2. STAND に金ﾆｽを塗布する"
],
"WorkPoints": [
"※ﾋﾟﾝ圧入面と下面は塗布し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下面への塗布禁止",
"◆作業者安全作業"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立①",
"WorkItems": [
"1. STAND に①を圧入する",
"◆2. STAND に金ﾆｽを塗布する"
],
"WorkPoints": [
"※ﾋﾟﾝ圧入面と下面は塗布し無い事",
"出代:2.5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"下面への塗布禁止",
"ﾋﾟﾝ圧入面への塗布禁止"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ圧入面と下面は塗布し無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ①に②を⑯で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする",
"3.LMｶﾞｲﾄﾞ両終端に抜け防止治具を取付ける ※ﾘﾃｰﾅｰ無し仕様の為､ﾎﾞｰﾙ抜けのﾘｽｸ有り4.基準側にﾀﾞｲﾔﾙｹﾞｰｼﾞを取付け､従動側を 平行調整し本締めする",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"平行度:0.02㎜以内 (ｽﾄﾛｰｸ110mm)",
"基準面",
"基準面"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:部品確認"
],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:MH軸LMｶﾞｲﾄﾞの平行度",
"押し当て",
"WWYJ-5300-057"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ①に②を⑯で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする",
"3.LMｶﾞｲﾄﾞ両終端に抜け防止治具を取付ける ※ﾘﾃｰﾅｰ無し仕様の為､ﾎﾞｰﾙ抜けのﾘｽｸ有り4.基準側にﾀﾞｲﾔﾙｹﾞｰｼﾞを取付け､従動側を 平行調整し本締めする",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"平行度:0.02㎜以内 (ｽﾄﾛｰｸ110mm)",
"基準面",
"基準面"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸LMｶﾞｲﾄﾞの平行度"
],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:部品確認",
"押し当て",
"WWYJ-5300-057"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "78㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ①に②を⑯で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う"
],
"WorkPoints": [
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"検査表①:MH軸LMｶﾞｲﾄﾞの平行度",
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "78.0㎜±0.01㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ①に②を⑯で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う"
],
"WorkPoints": [
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"検査表①:MH軸LMｶﾞｲﾄﾞの平行度",
"◆作業者安全作業",
"WWYJ-5300-057"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾄﾛｰｸ110㎜で0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立②",
"WorkItems": [
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ①に②を⑯で取付ける",
"3. LMｶﾞｲﾄﾞの平行出しを行う",
"◆4. 3完成品取付け面に金ﾆｽを塗布する"
],
"WorkPoints": [
"基準側(KB側)",
"従動側",
"1.基準面をﾋﾟﾝに押し当てて取付ける",
"2.従動側を仮止めする",
"3.LMｶﾞｲﾄﾞ両終端に抜け防止治具を取付ける ※ﾘﾃｰﾅｰ無し仕様の為､ﾎﾞｰﾙ抜けのﾘｽｸ有り4.基準側にﾀﾞｲﾔﾙｹﾞｰｼﾞを取付け､従動側を 平行調整し本締めする",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ78mm",
"平行度:0.02㎜以内 (ｽﾄﾛｰｸ110mm)",
"基準面",
"基準面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:部品確認",
"検査表①:MH軸LMｶﾞｲﾄﾞの平行度",
"押し当て"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立③",
"WorkItems": [
"1. ②に③を取付ける",
"2. 1.完成品を①のLMｽﾗｲﾀﾞｰに圧入する"
],
"WorkPoints": [
"4ｾｯﾄ組立",
"4箇所",
"半球側をｽﾗｲﾀﾞｰｸﾞﾘｰｽ注入部に圧入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｽﾀﾝﾄﾞ部_組立④",
"WorkItems": [
"1. ②に③を取付ける",
"2. 1.完成品を①のｽﾗｲﾀﾞｰﾆｯﾌﾟﾙに挿し込む"
],
"WorkPoints": [
"2ｾｯﾄ組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"挿し込む",
"挿し込む",
"挿し込む",
"挿し込む"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立①",
"WorkItems": [
"1. ①の取付け面にｱﾙｶﾝｻｽをかける",
"2. 1完成品に②を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立②",
"WorkItems": [
"◆1. ②をｸﾞﾘｰｽｱｯﾌﾟする",
"2. ①に1完成品と③④を組込む"
],
"WorkPoints": [
"②ﾍﾞｱﾘﾝｸﾞは背面合わせの事(下図参照)",
"断面図"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞへのｸﾞﾘｰｽｱｯﾌﾟ"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"*10㎜程度",
"空間容積の20%程度",
"検査表①:ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞの合わせﾏｰｸ",
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の20%程度",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立②",
"WorkItems": [
"◆1. ②をｸﾞﾘｰｽｱｯﾌﾟする",
"2. ①に1完成品と③④を組込む"
],
"WorkPoints": [
"②ﾍﾞｱﾘﾝｸﾞは背面合わせの事(下図参照)",
"断面図"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞの合わせﾏｰｸ"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"*10㎜程度",
"空間容積の20%程度",
"検査表①:ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞへのｸﾞﾘｰｽｱｯﾌﾟ",
"WWYJ-5300-057"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾍﾞｱﾘﾝｸﾞ背面合わせ",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "1.27㎜",
"ToolOther": "2.5±0.2N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立③",
"WorkItems": [
"3. 2完成品に⑥を取付ける",
"4. 3完成品に④を⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞの予圧管理"
],
"WorkTypes": [],
"Words": [
"矢視A"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±0.2N･m",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾋﾟｽﾄﾝ側面に塗布小豆:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾘﾝｸﾞ全体に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘﾝﾀﾞ摺動部内壁に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀIEL/V",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"2. ①に⑤④⑤③の順で取付け②で締付ける",
"1. ①の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"断面図",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄが抜けないようにｲﾝｼｭﾛｯｸで結束する (2本)",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄの先端部を測定する",
"芯振れ:0.012㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ﾎﾞｰﾙｽﾌﾟﾗｲﾝの芯振れ"
],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-057"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"2. ①に⑤④⑤③の順で取付け②で締付ける",
"1. ①の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"断面図",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄが抜けないようにｲﾝｼｭﾛｯｸで結束する (2本)",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄの先端部を測定する",
"芯振れ:0.012㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:部品確認"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾎﾞｰﾙｽﾌﾟﾗｲﾝの芯振れ",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-057"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑤",
"WorkItems": [
"2. ①に⑤④⑤③の順で取付け②で締付ける",
"1. ①の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. 2完成品をVﾌﾞﾛｯｸにｾｯﾄして､芯ﾌﾞﾚを測定する"
],
"WorkPoints": [
"断面図",
"ｽﾌﾟﾗｲﾝｼｬﾌﾄの先端部を測定する",
"芯振れ:0.012㎜以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾎﾞｰﾙｽﾌﾟﾗｲﾝの芯振れ",
"検査表①:部品確認",
"WWYJ-5300-057"
]
} | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.012㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "1.2~1.6cN･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組立⑥",
"WorkItems": [
"3. θ軸の回転ﾄﾙｸを確認､調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-057"
]
} | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "1.2cN･m~1.6cN･m",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｽﾗｲﾀﾞｰ部_組込み",
"WorkItems": [
"1. ①に②を⑯⑰⑱で取付ける"
],
"WorkPoints": [
"②を左側に押し当てて取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押し当て",
"押し当て"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. ①の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ③の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､②を⑯で取付ける",
"4. 3完成品に2完成品を⑰で取付ける"
],
"WorkPoints": [
"断面図",
"②ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"③付属ﾎﾞﾙﾄで締結する",
"型式確認､ｼﾘｱﾙNo.",
"ﾎﾞﾙﾄ締付け位置注意する事",
"③付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [],
"Words": [
"検査表①:.部品確認",
"検査表①:MHV軸ﾓｰﾀｰとﾊｰﾓﾆｯｸの連結距離",
"MHVMM4106P",
"MHVEM4106P",
"WWYJ-5300-057"
]
} | {
"QualityItem": "①の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. ①の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ③の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､②を⑯で取付ける",
"4. 3完成品に2完成品を⑰で取付ける"
],
"WorkPoints": [
"断面図",
"②ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"③付属ﾎﾞﾙﾄで締結する",
"型式確認､ｼﾘｱﾙNo.",
"ﾎﾞﾙﾄ締付け位置注意する事",
"③付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:.部品確認"
],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:MHV軸ﾓｰﾀｰとﾊｰﾓﾆｯｸの連結距離",
"MHVMM4106P",
"MHVEM4106P",
"WWYJ-5300-057"
]
} | {
"QualityItem": "①の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. ①の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ③の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､②を⑯で取付ける",
"4. 3完成品に2完成品を⑰で取付ける"
],
"WorkPoints": [
"断面図",
"②ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"③付属ﾎﾞﾙﾄで締結する",
"型式確認､ｼﾘｱﾙNo.",
"ﾎﾞﾙﾄ締付け位置注意する事",
"③付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MHV軸ﾓｰﾀｰとﾊｰﾓﾆｯｸの連結距離"
],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:.部品確認",
"MHVMM4106P",
"MHVEM4106P",
"WWYJ-5300-057"
]
} | {
"QualityItem": "③の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"■1. ①の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. ③の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"3. 1完成品にLABEL TERMINAL PROCESS を取付け､②を⑯で取付ける",
"4. 3完成品に2完成品を⑰で取付ける"
],
"WorkPoints": [
"断面図",
"②ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"③付属ﾎﾞﾙﾄで締結する",
"型式確認､ｼﾘｱﾙNo.",
"ﾎﾞﾙﾄ締付け位置注意する事",
"③付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:.部品確認",
"検査表①:MHV軸ﾓｰﾀｰとﾊｰﾓﾆｯｸの連結距離",
"MHVMM4106P",
"MHVEM4106P",
"WWYJ-5300-057"
]
} | {
"QualityItem": "③の製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"4. 3完成品に2完成品を⑰で取付ける"
],
"WorkPoints": [
"断面図",
"②ﾓｰﾀｰｼｬﾌﾄ先端出代:3.3±0.2㎜",
"③付属ﾎﾞﾙﾄで締結する",
"ﾎﾞﾙﾄ締付け位置注意する事",
"③付属ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:MHV軸ﾓｰﾀｰとﾊｰﾓﾆｯｸの連結距離",
"■安全作業",
"WWYJ-5300-057"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:3.3㎜±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組立②",
"WorkItems": [
"1. ①に②を⑯⑰⑱で取付ける"
],
"WorkPoints": [
"断面図",
"仮締め:SD-A044467-027にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ﾓｰﾀｰ部_組込み",
"WorkItems": [
"1. ①に②を⑯で取付ける"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締付け位置注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. ⑤にｸﾞﾘｰｽを充填する",
"◆1. ①に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に②③を⑯で取付ける",
"3. ④に②③を⑯で取付ける",
"5. 2完成品に4完成品を挿入し､⑥⑰⑱で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
"下面･左面は塗布し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"ｸﾞﾘｰｽ:空間容積の20%",
"下面への塗布禁止",
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"左面への塗布禁止",
"挿入",
"挿入"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "下面・左面は塗布しない",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. ⑤にｸﾞﾘｰｽを充填する",
"◆1. ①に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に②③を⑯で取付ける",
"3. ④に②③を⑯で取付ける",
"5. 2完成品に4完成品を挿入し､⑥⑰⑱で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
"下面･左面は塗布し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"ｸﾞﾘｰｽ:空間容積の20%",
"下面への塗布禁止",
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"左面への塗布禁止",
"挿入",
"挿入"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の20%程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立①",
"WorkItems": [
"◆4. ⑤にｸﾞﾘｰｽを充填する",
"◆1. ①に油砥石をかけ､金ﾆｽを塗布する",
"2. 1完成品に②③を⑯で取付ける",
"3. ④に②③を⑯で取付ける",
"5. 2完成品に4完成品を挿入し､⑥⑰⑱で取付ける"
],
"WorkPoints": [
"5mm程度",
"正面合わせにて挿入する",
"下面･左面は塗布し無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ容器",
"ｸﾞﾘｰｽ:空間容積の20%",
"下面への塗布禁止",
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"左面への塗布禁止",
"挿入",
"挿入"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立②",
"WorkItems": [
"2. ①に②を挿入する",
"3. 2完成品に③を挿入する",
"4. 3完成品に③を挿入し締付ける",
"5. ④付属のｾｯﾄﾋﾟｰｽ､ｾｯﾄﾋﾞｽで固定する",
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 7.5N･m"
],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:部品確認"
],
"WorkTypes": [],
"Words": [
"挿入1",
"挿入2",
"挿入3",
"WWYJ-5300-057"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立②",
"WorkItems": [
"2. ①に②を挿入する",
"3. 2完成品に③を挿入する",
"4. 3完成品に③を挿入し締付ける",
"5. ④付属のｾｯﾄﾋﾟｰｽ､ｾｯﾄﾋﾞｽで固定する",
"1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 7.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"挿入1",
"挿入2",
"挿入3",
"WWYJ-5300-057"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "7.5N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 7.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"挿入1",
"挿入2",
"挿入3"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "7.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み①",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける"
],
"WorkPoints": [
"平行度:0.02㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸ﾎﾞｰﾙねじとLMｶﾞｲﾄﾞとの平行度 LMｶﾞｲﾄﾞとの芯振れ"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-057"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み②",
"WorkItems": [
"2. 1完成品ﾍﾞｱﾘﾝｸﾞに①を挿し込み⑤で取付ける",
"1. ②のﾎﾞｰﾙﾈｼﾞに③④を取付ける",
"3. ②のﾎﾞｰﾙﾈｼﾞ先端に⑥を⑦で取付ける"
],
"WorkPoints": [
"押し当てて取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み③",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾈｼﾞの芯振れを測定する"
],
"WorkPoints": [
"芯振れ測定:0.01㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸ﾎﾞｰﾙねじとLMｶﾞｲﾄﾞとの平行度 LMｶﾞｲﾄﾞとの芯振れ"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-057"
]
} | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01m以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "7cN･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み③",
"WorkItems": [
"2. 1完成品のﾎﾞｰﾙねじの回転ﾄﾙｸを3か所測定する"
],
"WorkPoints": [
"①上側",
"②中央",
"③下側"
],
"Tolks": [
"回転ﾄﾙｸ:7cN･m以内"
],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸ﾎﾞｰﾙねじ回転ﾄﾙｸ(ﾓｰﾀｰ取付前)"
],
"WorkTypes": [],
"Words": [
"①~③ﾊﾞﾗﾂｷ:2cN･m以内",
"WWYJ-5300-057"
]
} | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品に③を挿入し､①に⑯で仮締めする"
],
"WorkPoints": [
"本締め",
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"MHEM4105P",
"MHMM4105P",
"MHBM4105P",
"仮止め:SD-A044467-023にて本締め",
"WWYJ-5300-057"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品に③を挿入し､①に⑯で仮締めする"
],
"WorkPoints": [
"本締め",
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:安全部品確認",
"MHEM4105P",
"MHMM4105P",
"MHBM4105P",
"仮止め:SD-A044467-023にて本締め",
"WWYJ-5300-057"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "19.6N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [],
"WorkPoints": [
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"MHEM4105P",
"MHMM4105P",
"■安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "19.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [],
"WorkPoints": [
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"MHEM4105P",
"MHMM4105P",
"■安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. ②の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品に③を挿入し､①に⑯で仮締めする"
],
"WorkPoints": [
"本締め",
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【金ﾆｽｾｯﾄ】",
"･金ﾆｽ",
"･保護ﾒｶﾞﾈ",
"･防毒ﾏｽｸ",
"･保護手袋",
"検査表①:安全部品確認",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"MHEM4105P",
"MHMM4105P",
"MHBM4105P",
"仮止め:SD-A044467-023にて本締め"
]
} | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_組込み⑤",
"WorkItems": [
"1. ①のﾍﾞｰｽに②を⑯⑰⑱で取付ける",
"2. ①のﾌﾞﾛｯｸに③を⑯⑲で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_原点出し①",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"矢視A",
"【MH軸原点出し手順】",
"1. ①のﾓｰﾀｰﾌﾞﾗｹｯﾄ側ｽﾄｯﾊﾟｰとﾎﾞｰﾙねじ間にﾌﾞﾛｯｸｹﾞｰｼﾞ(5mm)を挟み込む",
"2. 1の位置でRUFｾﾝｻｰの中心になるように①のｾﾝｻｰﾄﾞｸﾞ位置を調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"矢視A",
"ｽﾄｯﾊﾟｰ",
"ﾎﾞｰﾙねじ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RUFｾﾝｻｰ",
"ｾﾝｻｰﾄﾞｸﾞ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5.0㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"【MH軸原点出し手順】",
"本締め",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m",
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"原点出し治具",
"ﾌﾞﾚｰｷ解除治具",
"WWYJ-5300-057"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(24V_PFSS輸出用)",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"【MH軸原点出し手順】",
"本締め",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m",
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"原点出し治具",
"ﾌﾞﾚｰｷ解除治具",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"WWYJ-5300-057"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "19.6N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"【MH軸原点出し手順】",
"本締め",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m",
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"原点出し治具",
"ﾌﾞﾚｰｷ解除治具",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ",
"WWYJ-5300-057"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "19.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"【MH軸原点出し手順】",
"本締め",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m",
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"原点出し治具",
"ﾌﾞﾚｰｷ解除治具",
"検査表①:MH軸Nｶｯﾌﾟ締付ﾄﾙｸ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [
"1. ①に付属ｾﾝｻｰと②を取付ける",
"2. ③に1完成品を④で取付ける"
],
"WorkPoints": [
"①付属の小径ﾜｯｼｬｰを入れる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.3,0.5㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸落下防止ｼﾘﾝﾀﾞｰの組付"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"◆作業者安全作業",
"WWYJ-5300-057"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.3,0.5㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [
"1. ①に付属ｾﾝｻｰと②を取付ける",
"2. ③に1完成品を④で取付ける",
"3. 2完成品のｼﾘﾝﾀﾞﾛｯﾄﾞ先端に⑤を取付ける",
"◆4. ⑥にｸﾞﾘｰｽを塗り､3完成品に⑦⑧で取付ける"
],
"WorkPoints": [
"4㎜",
"0.5±0.2㎜",
"0.5±0.2㎜",
"①付属の小径ﾜｯｼｬｰを入れる事",
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"ｸﾞﾘｰｽ塗布 米粒:2",
"検査表①:MH軸落下防止ｼﾘﾝﾀﾞｰの組付",
"矢視A"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組込み",
"WorkItems": [
"1. ②にLABEL TERMINAL PROCESS を取付ける",
"2. ①に1完成品を③⑯で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"1B10930-8R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ｾﾝｻｰ部_組込み①",
"WorkItems": [
"1. ②に③を④で取付ける",
"2. ①のｽﾌﾟﾗｲﾝ先端部に1完成品を⑤で取付ける"
],
"WorkPoints": [
"ｾﾝｻｰとの位置調整するため､仮取付にする",
"SD-A044467-027-00 にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ｾﾝｻｰ部_組込み②",
"WorkItems": [],
"WorkPoints": [
"矢視A",
"【MHV軸原点出し手順】",
"1.①のMHV軸ﾓｰﾀｰに原点出し治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"3. PHﾁｪｯｶｰで ORGｾﾝｻｰ がONする位置に①のｾﾝｻｰﾄﾞｸﾞを調整する",
"4. 軸を左右に回転させ +LIM ､ -LIM が遮光することを確認する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MHV軸原点調整"
],
"WorkTypes": [],
"Words": [
"矢視A",
"WWYJ-5300-057"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_MHV軸ｾﾝｻｰ部_組込み②",
"WorkItems": [],
"WorkPoints": [
"矢視A",
"【MHV軸原点出し手順】",
"1.①のMHV軸ﾓｰﾀｰに原点出し治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"3. PHﾁｪｯｶｰで ORGｾﾝｻｰ がONする位置に①のｾﾝｻｰﾄﾞｸﾞを調整する",
"4. 軸を左右に回転させ +LIM ､ -LIM が遮光することを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:MHV軸原点調整",
"矢視A",
"WWYJ-5300-057"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ｵｲﾙﾊﾟﾝ_組込み",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [
"◆1. ⑯③⑤に耐熱ｸﾞﾘｰｽを塗布する",
"2. ①に②を圧入する",
"3. ①のｶｯﾌﾟﾘﾝｸﾞ部を⑯で仮締めする",
"4. 3完成品に③④⑤を取付ける"
],
"WorkPoints": [
"仮締め:SD-A044467-034にて本締め",
"出代 :3.5㎜",
"矢視A",
"前後左右4箇所",
"14.0±0.1㎜",
"背面隙間を14㎜に調整し､他3箇所は当付け均等で締付け"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:高温部ﾎﾞﾙﾄへの耐熱ｸﾞﾘｰｽ塗布"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"矢視A",
"検査表①:ﾎﾙﾀﾞｰ高さ調整",
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [
"2. ①に②を圧入する",
"3. ①のｶｯﾌﾟﾘﾝｸﾞ部を⑯で仮締めする"
],
"WorkPoints": [
"仮締め:SD-A044467-034にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [],
"WorkPoints": [
"出代 :3.5㎜",
"矢視A",
"前後左右4箇所",
"背面隙間を14㎜に調整し､他3箇所は当付け均等で締付け"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ﾎﾙﾀﾞｰ高さ調整"
],
"WorkTypes": [],
"Words": [
"矢視A",
"◆作業者安全作業",
"WWYJ-5300-057"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:14.0㎜±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立②",
"WorkItems": [
"2. ①に②③を取付ける",
"3. 2完成品に④を⑤で取付ける",
"◆1. ②③⑤ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:高温部ﾎﾞﾙﾄへの耐熱ｸﾞﾘｰｽ塗布"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1",
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立③",
"WorkItems": [
"1. ②に⑥を貼付ける"
],
"WorkPoints": [
"10㎜",
"15㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:10.0㎜±0.5㎜15.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(逆流れ)_ﾍｯﾄﾞ先端部_組立③",
"WorkItems": [
"◆2. ⑯ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"3. ①に1完成品を⑯⑰で取付ける",
"1. ②に⑥を貼付ける"
],
"WorkPoints": [
"10㎜",
"15㎜"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:高温部ﾎﾞﾙﾄへの耐熱ｸﾞﾘｰｽ塗布"
],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"WWYJ-5300-057"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.