input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｷﾏ確認治具",
"Size": "5㎜",
"ToolOther": "FM-3224",
"WorkName": "前面左右下ｶﾊﾞｰ取付",
"WorkItems": [
"3. 上カバーとCOVER の間に㉖治具（5㎜）を挟み②で固定"
],
"WorkPoints": [
"ﾒｰﾀとｹﾞｰｼﾞがｶﾊﾞｰの中央にあるか､確認",
"ﾒｰﾀのSW部がｶﾊﾞｰｰと干渉していないか確認",
"ﾌﾞﾗｹｯﾄ調整にて開口部中央が出ない時､5㎜の隙間を無視しｾﾝﾀｰ重視にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側",
"後側",
"現在の作業位置",
"前側",
"後側",
"現在の作業位置",
"前側",
"後側",
"現在の作業位置",
"5㎜",
"SD差込口が中央に来ること"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ｽｷﾏ確認治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "前面左右下ｶﾊﾞｰ取付",
"WorkItems": [
"3. 上カバーとCOVER の間に㉖治具（5㎜）を挟み②で固定"
],
"WorkPoints": [
"ﾒｰﾀとｹﾞｰｼﾞがｶﾊﾞｰの中央にあるか､確認",
"ﾒｰﾀのSW部がｶﾊﾞｰｰと干渉していないか確認",
"ﾌﾞﾗｹｯﾄ調整にて開口部中央が出ない時､5㎜の隙間を無視しｾﾝﾀｰ重視にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側",
"後側",
"現在の作業位置",
"前側",
"後側",
"現在の作業位置",
"5㎜",
"SD差込口が中央に来ること"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付寸法:架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"下側より取付",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"現在の作業位置",
"後側",
"前側",
"50㎜",
"切替仕様時も取付る事",
"26.5N･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付寸法:架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"下側より取付",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"現在の作業位置",
"後側",
"前側",
"50㎜",
"切替仕様時も取付る事",
"26.5N･m"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:50㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-3310",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取付寸法:架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"下側より取付",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"現在の作業位置",
"後側",
"前側",
"50㎜",
"切替仕様時も取付る事",
"26.5N･m"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3310",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "ﾌﾞﾗｹｯﾄ位置決め治具",
"RecordMethod": "-",
"Other": "ﾄﾚｲ仕様切替仕様",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｷﾏ確認治具",
"Size": "5㎜",
"ToolOther": "FM-3224",
"WorkName": "右側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"3. 調整･締付け",
"1. COVER をSCREW で仮付",
"2. COVER ･COVER をSCREW で仮付",
"3. 調整･締付け",
"1. COVER をSCREW で仮付"
],
"WorkPoints": [
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"中央に仮付",
"COVER とCOVER COVER の隙間を1~2㎜開けること",
"高さを中央ｶﾊﾞｰに合わせる(隙間5㎜)",
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"中央に仮付",
"COVER とCOVER COVER の隙間を1~2㎜開けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側",
"現在の作業位置",
"高さをそろえる",
"高さをそろえる",
"ｶﾐﾅﾘﾏｰｸが左下",
"ｶﾐﾅﾘﾏｰｸが右下",
"前側"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ｽｷﾏ確認治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.3",
"ToolOther": "350cN･m",
"WorkName": "右側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"3. 調整･締付け",
"1. COVER をSCREW で仮付"
],
"WorkPoints": [
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"中央に仮付",
"COVER とCOVER COVER の隙間を1~2㎜開けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"3. 調整･締付け",
"1. COVER をSCREW で仮付"
],
"WorkPoints": [
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"中央に仮付",
"COVER とCOVER COVER の隙間を1~2㎜開けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1~2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [],
"WorkPoints": [
"配線終了後にPCｶﾊﾞｰを再度取付",
"参考値:ﾚｰﾙとｶﾊﾞｰの隙間7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [],
"WorkPoints": [
"配線終了後にPCｶﾊﾞｰを再度取付",
"参考値:ﾚｰﾙとｶﾊﾞｰの隙間7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [],
"WorkPoints": [
"配線終了後にPCｶﾊﾞｰを再度取付",
"参考値:ﾚｰﾙとｶﾊﾞｰの隙間7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側延長ｺﾝﾍﾞｱ配線①",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱのP板検出の配線を接続しｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"ｺﾈｸﾀ名称 (右側)B1114R･B1116R",
"ﾋﾟﾝの破損､抜けの確認をする",
"配線に負荷がかからない様､注意"
],
"Tolks": [],
"InspectionNo": "WEBS-F013-103",
"InspectionItems": [
"検査表①:延長ｺﾝﾍﾞｱｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"B1114R",
"前側",
"後側",
"現在の作業位置",
"B1116R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEBS-F013-103"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "延長ｺﾝﾍﾞｱ仕様",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"1. COVER をSCREW で取付"
],
"WorkPoints": [
"COVER ｶﾊﾞｰ取付時､配線の挟み込みに注意･確認してから締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"1. COVER をSCREW で取付"
],
"WorkPoints": [
"COVER ｶﾊﾞｰ取付時､配線の挟み込みに注意･確認してから締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"3. ｱﾝﾀﾞｰｶﾊﾞｰにCABLE-SUPPORT BOLT を取付",
"1. COVER をSCREW で取付",
"2. 外したPCｶﾊﾞｰ取付"
],
"WorkPoints": [
"M6ﾄﾗｽﾎﾞﾙﾄを取外して取付",
"取外したPCｶﾊﾞｰを取付 ･M4ﾎﾞﾙﾄ6本",
"COVER ｶﾊﾞｰ取付時､配線の挟み込みに注意･確認してから締結する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 110N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "延長ｺﾝﾍﾞｱ仕様",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲ接続ｺﾈｸﾀｰｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [
"1. 架台に①を付属ﾈｼﾞで取付"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側 左下ｶﾊﾞｰに取付",
"切替仕様時作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"台車使用時の取付方",
"ﾄﾚｲ使用時の取付方"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ確認",
"WorkItems": [
"4. 4つの水準器が3目盛(0.06㎜)以内になるよう調整",
"4. 4つの水準器が3目盛(0.06㎜)以内になるよう調整"
],
"WorkPoints": [
"調整時にｱｼﾞｬｽﾄﾎﾞﾙﾄの浮きがないように注意する",
"調整時にｱｼﾞｬｽﾄﾎﾞﾙﾄの浮きがないように注意する"
],
"Tolks": [],
"InspectionNo": "WEBS-F013-101",
"InspectionItems": [
"検査表①:架台ﾚﾍﾞﾙ確認",
"検査表①:架台ﾚﾍﾞﾙ確認"
],
"WorkTypes": [],
"Words": [
"WEBS-F013-101"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3目盛(0.06㎜)以内",
"Method": "目視",
"RecordMethod": "WEBS-F013-101",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5858",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [
"2. ﾍｯﾄﾞﾌﾟﾚｰﾄに㉗-１を仮取付けする",
"1. ﾈｼﾞを4箇所緩める",
"3. 高さ調整治具位置出しを行う",
"4. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄの位置決めﾋﾟﾝを㉗-1に押し当て締結する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"㉗-1をﾍｯﾄﾞ取付け部にｾｯﾄする（治具を上に持ち上げ仮止め）",
"X軸及びY軸を移動し㉗-1を㉗-2の上に移動",
"㉗-1の仮止めﾋﾞｽを緩め㉗の1を㉗-2に当付けﾋﾞｽを締結する",
"ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ取付後､治具にﾋﾟﾝが当たっているかｼｯｸﾈｽｹﾞｰｼﾞにて確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉗-１",
"㉗-2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5858",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"X軸及びY軸を移動し㉗-1を㉗-2の上に移動",
"㉗-1の仮止めﾋﾞｽを緩め㉗の1を㉗-2に当付けﾋﾞｽを締結する",
"ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ取付後､治具にﾋﾟﾝが当たっているかｼｯｸﾈｽｹﾞｰｼﾞにて確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"X軸及びY軸を移動し㉗-1を㉗-2の上に移動",
"㉗-1の仮止めﾋﾞｽを緩め㉗の1を㉗-2に当付けﾋﾞｽを締結する",
"ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ取付後､治具にﾋﾟﾝが当たっているかｼｯｸﾈｽｹﾞｰｼﾞにて確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付",
"ｼﾘｱﾙNo.記載位置",
"規正ﾋﾟﾝ穴",
"規正ﾋﾟﾝ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:1. 型式･検査書確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付",
"ｼﾘｱﾙNo.記載位置",
"規正ﾋﾟﾝ穴",
"規正ﾋﾟﾝ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:1. 型式･検査書確認"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D08"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付",
"ｼﾘｱﾙNo.記載位置",
"規正ﾋﾟﾝ穴",
"規正ﾋﾟﾝ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:1. 型式･検査書確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ取付け(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付",
"ｼﾘｱﾙNo.記載位置",
"規正ﾋﾟﾝ穴",
"規正ﾋﾟﾝ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:1. 型式･検査書確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "検査書有無確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ接続(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗより配線が出無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事",
"ｺﾈｸﾀが差込めるようにRを小さくとる事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付け確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ接続(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗより配線が出無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事",
"ｺﾈｸﾀが差込めるようにRを小さくとる事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付け確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗ接続(標準:ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗより配線が出無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事",
"ｺﾈｸﾀが差込めるようにRを小さくとる事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付け確認"
],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ取付け(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA:(WD42) をBOLT WASHER で取付ける",
"■1. HEAD CAMERA:(WD42) の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する"
],
"WorkPoints": [
"規正ﾋﾟﾝ",
"規正ﾋﾟﾝ穴",
"ｼﾘｱﾙNo.記載位置",
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表HEAD CAMERA:(WD42) :1. 型式･検査書確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ取付け(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA:(WD42) をBOLT WASHER で取付ける",
"■1. HEAD CAMERA:(WD42) の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する"
],
"WorkPoints": [
"規正ﾋﾟﾝ",
"規正ﾋﾟﾝ穴",
"ｼﾘｱﾙNo.記載位置",
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表HEAD CAMERA:(WD42) :1. 型式･検査書確認"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D08"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ取付け(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA:(WD42) をBOLT WASHER で取付ける",
"■1. HEAD CAMERA:(WD42) の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する"
],
"WorkPoints": [
"規正ﾋﾟﾝ",
"規正ﾋﾟﾝ穴",
"ｼﾘｱﾙNo.記載位置",
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表HEAD CAMERA:(WD42) :1. 型式･検査書確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ取付け(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA:(WD42) をBOLT WASHER で取付ける",
"■1. HEAD CAMERA:(WD42) の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する"
],
"WorkPoints": [
"規正ﾋﾟﾝ",
"規正ﾋﾟﾝ穴",
"ｼﾘｱﾙNo.記載位置",
"ｶﾒﾗ側の規正穴とﾌﾟﾚｰﾄ側の規正ﾋﾟﾝを合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表HEAD CAMERA:(WD42) :1. 型式･検査書確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "検査書有無確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ接続(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗに配線が接触して無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ接続(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗに配線が接触して無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞｶﾒﾗ接続(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"■1. ｶﾒﾗｹｰﾌﾞﾙを接続する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"基板ｶﾒﾗに配線が接触して無い事",
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表②:20.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付確認"
],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP対応】ｸﾘｯﾌﾟ取付け(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"1. CLIP をBOLT で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】配線引き回し(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"2. 配線を引き回し､ｲﾝｼｭﾛｯｸで固定する",
"1. 文字認識ﾍｯﾄﾞｶﾒﾗにCABLE を接続し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"文字認識ｶﾒﾗに接触しないように配線を固定",
"ﾍｯﾄﾞを右側ﾒｶｽﾄに当付けた際に､配線と接触し無い事",
"下枠から配線を通す",
"配線の余長を矢印方向に逃がす"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表CABLE :4.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP対応】ｸﾘｯﾌﾟ取付け(高さｾﾝｻ仕様)",
"WorkItems": [
"1. CLIP をBOLT で取付ける",
"1. CLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP対応】高さｾﾝｻ取付け(高さｾﾝｻ仕様)",
"WorkItems": [
"1. ①をBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの裏側から固定する"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】配線引き回し(高さｾﾝｻ仕様)",
"WorkItems": [
"2. 配線を引き回し､ｲﾝｼｭﾛｯｸで固定する",
"1. 配線を引き回し､ｲﾝｼｭﾛｯｸで固定する(ﾌｪﾗｲﾄｺｱから固定)"
],
"WorkPoints": [
"配線の余長を矢印方向に逃がす",
"ﾍｯﾄﾞを右側ﾒｶｽﾄに当付けた際に､配線と接触し無い事",
"下枠から配線を通す",
"ﾌｪﾗｲﾄｺｱはﾏｳﾝﾄに合わせて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線用ﾏｳﾝﾄ取付け",
"WorkItems": [
"1. CABLE-SUPPORT を㉖で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"取付け方向",
"全12箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"丸穴ｾﾝﾀｰでの取付のこと"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ取付け1",
"WorkItems": [
"3. ①のX軸固定側をBOLT で取付ける",
"3. ①のX軸固定側をBOLT で取付ける"
],
"WorkPoints": [
"ﾍﾞｱを反時計回りに半回転させ､取付ける",
"ﾍﾞｱを反時計回りに半回転させ､取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7 組立時調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ取付け1",
"WorkItems": [
"2. ①のY軸稼働側をBOLT で取付ける",
"3. ①のX軸固定側をBOLT で取付ける",
"1. ①のY軸固定側をBOLT で取付ける"
],
"WorkPoints": [
"ﾍﾞｱを反時計回りに半回転させ､取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:7 組立時調整"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D08"
]
} | {
"QualityItem": "組立時調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査書の規格値であること",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ取付け2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ取付け2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D08"
]
} | {
"QualityItem": "組立時調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査書の規格値であること",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "ﾓｰﾀ配線処理1",
"WorkItems": [
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM501】をBOLT WASHER で取付ける",
"■2. ｱｰｽ線をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ｼｰﾙ側が上にくるように取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:2 ﾈｼﾞ締めﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾓｰﾀ配線処理1",
"WorkItems": [
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM501】をBOLT WASHER で取付ける",
"■2. ｱｰｽ線をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ｼｰﾙ側が上にくるように取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:2 ﾈｼﾞ締めﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀ配線処理2",
"WorkItems": [
"3. ﾓｰﾀ線をｲﾝｼｭﾛｯｸで固定する",
"2. ﾓｰﾀｺﾈｸﾀを接続する",
"1. ﾓｰﾀｰｺﾈｸﾀを枠の中に通し､ﾓｰﾀ線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸで動力線を直に固定しない黒ﾁｭｰﾌﾞ箇所で固定",
"配線にたるみを持たせないようにする",
"ﾓｰﾀ配線の下にｸﾞﾘｰｽﾁｭｰﾌﾞを通しておくこと"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｴﾝｺｰﾀﾞｺﾈｸﾀ固定用ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. ①をBOLT WASHER BOLT で取付ける",
"1. ①の左枠に左側ｸﾞﾘｰｽﾁｭｰﾌﾞ×2､右枠に右側ｸﾞﾘｰｽﾁｭｰﾌﾞ×2 X軸ﾌｧﾝ配線を通す"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾄﾘﾑが付いている方を機械奥側にして取付",
"ﾌﾞﾗｹｯﾄを斜めにして挿入",
"取付方向",
"M4×6 (短い方)",
"M4×8 (長い方)",
"ﾎﾞﾙﾄの長さが違う為､付け間違いに気を付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｴﾝｺｰﾀﾞｺﾈｸﾀ固定用ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. ①をBOLT WASHER BOLT で取付ける",
"1. ①の左枠に左側ｸﾞﾘｰｽﾁｭｰﾌﾞ×2､右枠に右側ｸﾞﾘｰｽﾁｭｰﾌﾞ×2 X軸ﾌｧﾝ配線を通す"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾄﾘﾑが付いている方を機械奥側にして取付",
"ﾌﾞﾗｹｯﾄを斜めにして挿入",
"取付方向",
"M4×6 (短い方)",
"M4×8 (長い方)",
"ﾎﾞﾙﾄの長さが違う為､付け間違いに気を付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽﾁｭｰﾌﾞ取付け",
"WorkItems": [
"1. グリスチューブの長さを合わせ㉗で切断し、ジョイントに挿入する",
"2. ｸﾞﾘｰｽﾁｭｰﾌﾞをﾏｳﾝﾄにｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｸﾞﾘｰｽﾁｭｰﾌﾞが折れないようにを付けること",
"X軸 下側LMｶﾞｲﾄﾞ",
"X軸 上側LMｶﾞｲﾄﾞ",
"【XMM501】のｹｰﾌﾞﾙも一緒に固定すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"左側",
"右側",
"左側",
"右側",
"XMM501",
"左側",
"右側",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配線処理1",
"WorkItems": [
"3. 【XEM501】をﾌﾞﾗｹｯﾄに固定する",
"1. 【ｴﾝｺｰﾀﾞ線】【CN3/4】を板金の下枠に通し､ｲﾝｼｭﾛｯｸで固定する",
"2. 【XEM501】 【CN3/4】の配線を枠の中から通す､【CN3/4】をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"絶縁ﾁｭｰﾌﾞｾﾝﾀｰ位置に合わせて固定すること",
"CMFR は入れない",
"ｺﾈｸﾀの切り欠きがある方を上向きにする",
"ｺﾈｸﾀの爪がひっかかるところまで押し込むこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "43cN･m",
"WorkName": "ﾍｯﾄﾞ配線処理2",
"WorkItems": [
"1. 【1A21】をSCREW WASHER で取付る",
"2. ｴﾝｺｰﾀﾞ線･LED制御基板配線を整線し､ｴﾝｺｰﾀﾞ線を差込み後､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｴﾝｺｰﾀﾞ線はﾓｰﾀ線の内側を通す"
],
"Tolks": [
"締付ﾄﾙｸ 43cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"1A21"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "43cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配線処理2",
"WorkItems": [
"1. 【1A21】をSCREW WASHER で取付る",
"2. ｴﾝｺｰﾀﾞ線･LED制御基板配線を整線し､ｴﾝｺｰﾀﾞ線を差込み後､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"上図(配線引き回し)",
"角が直角に膨らむように整線する",
"ﾌﾞﾗｹｯﾄの切り欠きにｲﾝｼｭﾛｯｸを合わせる",
"ｴﾝｺｰﾀﾞ線はﾓｰﾀ線の内側を通す"
],
"Tolks": [
"締付ﾄﾙｸ 43cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･･･",
"･･･1A21",
"･･･XEM501",
"･･･CN14",
"･･･CN2",
"･･･CN16",
"ﾄﾞﾛｱｺﾈｸﾀ【1A21】",
"ｲﾝｼｭﾛｯｸ(100mm)",
"1A21"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞ配線引き回し(高さｾﾝｻ仕様)",
"WorkItems": [
"1. 配線【CN13】をｴﾝｺｰﾀﾞ線と配管の間を通す",
"2. 配線を引き回し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"上図(配線引き回し)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN13",
"･･･",
"･･･1A21",
"･･･XEM501",
"･･･CN14",
"･･･CN2",
"･･･CN16",
"ﾄﾞﾛｱｺﾈｸﾀ【1A21】",
"･･･CN13",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP対応】ﾍｯﾄﾞ配線引き回し(文字認識対応ﾍｯﾄﾞｶﾒﾗﾕﾆｯﾄ仕様)",
"WorkItems": [
"1. 配線【CN5】をｴﾝｺｰﾀﾞ線と配管の間を通す",
"2. 配線を引き回し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN5",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾍｯﾄﾞ配線処理3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ配線処理3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ配線処理4",
"WorkItems": [
"1. 【FGFX1】【FGFX2】をSCREW で取付る",
"2. LED制御基板配線を整線し､ｲﾝｼｭﾛｯｸで仮締めで保持する"
],
"WorkPoints": [
"左側から順に取付",
"※ﾌﾛﾝﾄ無し､ﾘｱのみ"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:2 ﾈｼﾞ締めﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED照明制御基板ｺﾈｸﾀ接続",
"WorkItems": [
"★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①にｺﾈｸﾀを接続する",
"3. 【CN17】の線をﾌﾞﾗｹｯﾄにｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"DipSWの設定を確認",
"ｼﾘｱﾙ№",
"型式",
"基板裏面が上側",
"真ん中の丸穴で固定",
"絶縁ﾁｭｰﾌﾞのｾﾝﾀｰ位置で下目にして固定",
"ｲﾝｼｭﾛｯｸの頭は外側に向けること"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:3 基板設定確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:1 型式･検査書確認",
"検査表①:4 ｺﾈｸﾀ接続確認",
"CN17",
"CN4",
"CN14",
"CN2",
"CN6",
"CN1",
"CN3",
"CN13",
"CN5",
"CN16",
"CN13はOP:文字認識仕様時のみ",
"CN5はOP:高さｾﾝｻ仕様時のみ",
"CN17",
"CN15",
"CN19",
"ｲﾝｼｭﾛｯｸ(100mm)",
"CN7",
"CN15は前準備で接続済",
"CN19は前準備で接続済",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED照明制御基板ｺﾈｸﾀ接続",
"WorkItems": [
"★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①にｺﾈｸﾀを接続する",
"3. 【CN17】の線をﾌﾞﾗｹｯﾄにｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"DipSWの設定を確認",
"ｼﾘｱﾙ№",
"型式",
"基板裏面が上側",
"真ん中の丸穴で固定",
"絶縁ﾁｭｰﾌﾞのｾﾝﾀｰ位置で下目にして固定",
"ｲﾝｼｭﾛｯｸの頭は外側に向けること"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:1 型式･検査書確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:3 基板設定確認",
"検査表①:4 ｺﾈｸﾀ接続確認",
"CN17",
"CN4",
"CN14",
"CN2",
"CN6",
"CN1",
"CN3",
"CN13",
"CN5",
"CN16",
"CN13はOP:文字認識仕様時のみ",
"CN5はOP:高さｾﾝｻ仕様時のみ",
"CN17",
"CN15",
"CN19",
"ｲﾝｼｭﾛｯｸ(100mm)",
"CN7",
"CN15は前準備で接続済",
"CN19は前準備で接続済",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED照明制御基板ｺﾈｸﾀ接続",
"WorkItems": [
"★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①にｺﾈｸﾀを接続する",
"3. 【CN17】の線をﾌﾞﾗｹｯﾄにｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"DipSWの設定を確認",
"ｼﾘｱﾙ№",
"型式",
"基板裏面が上側",
"真ん中の丸穴で固定",
"絶縁ﾁｭｰﾌﾞのｾﾝﾀｰ位置で下目にして固定",
"ｲﾝｼｭﾛｯｸの頭は外側に向けること"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:3 基板設定確認",
"検査表①:1 型式･検査書確認",
"CN17",
"CN4",
"CN14",
"CN2",
"CN6",
"CN1",
"CN3",
"CN13",
"CN5",
"CN16",
"CN13はOP:文字認識仕様時のみ",
"CN5はOP:高さｾﾝｻ仕様時のみ",
"CN17",
"CN15",
"CN19",
"ｲﾝｼｭﾛｯｸ(100mm)",
"CN7",
"CN15は前準備で接続済",
"CN19は前準備で接続済",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED照明制御基板ｺﾈｸﾀ接続",
"WorkItems": [
"★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①にｺﾈｸﾀを接続する",
"3. 【CN17】の線をﾌﾞﾗｹｯﾄにｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"DipSWの設定を確認",
"ｼﾘｱﾙ№",
"型式",
"基板裏面が上側",
"真ん中の丸穴で固定",
"絶縁ﾁｭｰﾌﾞのｾﾝﾀｰ位置で下目にして固定",
"ｲﾝｼｭﾛｯｸの頭は外側に向けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:3 基板設定確認",
"検査表①:1 型式･検査書確認",
"検査表①:4 ｺﾈｸﾀ接続確認",
"CN17",
"CN4",
"CN14",
"CN2",
"CN6",
"CN1",
"CN3",
"CN13",
"CN5",
"CN16",
"CN13はOP:文字認識仕様時のみ",
"CN5はOP:高さｾﾝｻ仕様時のみ",
"CN17",
"CN15",
"CN19",
"ｲﾝｼｭﾛｯｸ(100mm)",
"CN7",
"CN15は前準備で接続済",
"CN19は前準備で接続済",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "LED照明制御基板取付け",
"WorkItems": [
"1. SPACER を取付ける",
"★2. LED制御基板をSPACER で取付ける",
"3. 仮締め状態のｲﾝｼｭﾛｯｸを本締めして固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "120cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ中継ﾕﾆｯﾄ取付け",
"WorkItems": [
"1. ①BRACKET をBOLT で取付け"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ中継ﾕﾆｯﾄ取付け",
"WorkItems": [
"■2. ｶﾒﾗｹｰﾌﾞﾙをﾌﾞﾗｹｯﾄに固定する",
"3. ｶﾒﾗｹｰﾌﾞﾙ･CN17 の配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ中継ﾕﾆｯﾄ取付け",
"WorkItems": [
"1. ①BRACKET をBOLT で取付け",
"■2. ｶﾒﾗｹｰﾌﾞﾙをﾌﾞﾗｹｯﾄに固定する",
"3. ｶﾒﾗｹｰﾌﾞﾙ･CN17 の配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"CN17の折り返しを共縛り",
"ﾈｼﾞを完全に緩め片方ずつ枠に通していき固定する"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m",
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"CMFR",
"検査表①:4.ｺﾈｸﾀ接続確認",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "30cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ接続",
"WorkItems": [
"■2. ｶﾒﾗｹｰﾌﾞﾙをｺﾈｸﾀに接続する",
"1. ①をWASHER WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｶﾒﾗｹｰﾌﾞﾙ:CMFP",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ接続",
"WorkItems": [
"■2. ｶﾒﾗｹｰﾌﾞﾙをｺﾈｸﾀに接続する",
"1. ①をWASHER WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｶﾒﾗｹｰﾌﾞﾙ:CMFP",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "160cN･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ接続",
"WorkItems": [],
"WorkPoints": [
"SHIELD はｶﾒﾗｼｰﾙﾄﾞ部の中心になるように取付の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CMFP",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ接続",
"WorkItems": [
"3. ｶﾒﾗｹｰﾌﾞﾙにSHIELD を通し､SPACER BOLT WASHER で取付ける",
"■2. ｶﾒﾗｹｰﾌﾞﾙをｺﾈｸﾀに接続する",
"1. ①をWASHER WASHER BOLT で取付ける"
],
"WorkPoints": [
"SHIELD はｶﾒﾗｼｰﾙﾄﾞ部の中心になるように取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 30cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4 ｺﾈｸﾀ接続確認",
"ｶﾒﾗｹｰﾌﾞﾙ:CMFP",
"CMFP",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱ配管接続1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱ配管接続2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "55cN･m",
"WorkName": "ﾍｯﾄﾞｶﾊﾞｰ取付け",
"WorkItems": [
"1. COVER を被せる",
"2. COVER をSCREW で固定する"
],
"WorkPoints": [
"左右4箇所にねじを入れてから均等に下側に押さえながら締付けのこと"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左側",
"右側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理1",
"WorkItems": [
"2. Y軸右側ﾓｰﾀ線【YMM506】をBOLT WASHER で取付ける",
"1. Y軸右側に接続するﾓｰﾀ･ｴﾝｺｰﾀﾞ線を引き回しする"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"銘板が見えるように取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･･･YEM506",
"･･･YMM506",
"左側",
"右側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理2",
"WorkItems": [
"1. Y軸右側ﾓｰﾀ線を接続し､ｲﾝｼｭﾛｯｸで固定する",
"2. 【YEM506】【YMM506】をｲﾝｼｭﾛｯｸで固定する",
"3. 【YEM506】をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"黄色ﾏｰｷﾝｸﾞの位置でｲﾝｼｭﾛｯｸを固定する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･･･YEM506",
"･･･YMM506",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理3",
"WorkItems": [
"1. SPACER をWASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀ線を挟みこまないように気を付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理4",
"WorkItems": [
"2. 配線の余長を左側に持っていきながら､COVER をBOLT で固定する",
"1. 【YEM506】【YMM506】をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"線の余長を左側に持ってきながら固定する",
"ﾌﾞﾗｹｯﾄは機械奥側に押し当てて取付(青色矢印)"
],
"Tolks": [
"締付ﾄﾙｸ 243cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"配線の余長左側へ",
"右側",
"左側",
"配線の余長左側へ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "243cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理1",
"WorkItems": [
"2. Y軸右側ﾓｰﾀ線【YMM502】をBOLT WASHER で取付ける",
"1. Y軸右側に接続するﾓｰﾀ･ｴﾝｺｰﾀﾞ線を引き回しする"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"銘板が見えるように取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･･･YEM502",
"･･･YMM502"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. 【YEM502】【YMM502】をｲﾝｼｭﾛｯｸで固定する",
"3. 【YEM502】をｲﾝｼｭﾛｯｸで固定する",
"1. Y軸右側ﾓｰﾀ線を接続し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"黄色ﾏｰｷﾝｸﾞの位置でｲﾝｼｭﾛｯｸを固定する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･･･YEM502",
"･･･YMM502",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理3",
"WorkItems": [
"1. SPACER をWASHER BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀ線を挟みこまないように気を付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "X-Y軸連結部_ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER NUT で取付ける",
"2. ①をSCREW で取付ける",
"3. ①をNUT SCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視B"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "1.8N･m",
"WorkName": "X-Y軸連結部_ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER NUT で取付ける",
"2. ①をSCREW で取付ける",
"3. ①をNUT SCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視B"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "X-Y軸連結部_ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER NUT で取付ける",
"2. ①をSCREW で取付ける",
"3. ①をNUT SCREW で取付ける"
],
"WorkPoints": [
"取付け位置に配線があるので挟み込み注意",
"標準+ﾄﾞﾗｲﾊﾞｰはｱｸｾｽ不可の為､+ﾛﾝｸﾞﾋﾞｯﾄを使用し締付け",
"下記2.3作業を考慮して他ねじ穴位置を合わせておくこと",
"ﾌﾞﾗｹｯﾄをX軸ﾍﾞｱ受けの下にくるように取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A",
"矢視B",
"矢視B"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X-Y軸連結部_配線処理",
"WorkItems": [
"1. X･Y軸ｹｰﾌﾞﾙﾍﾞｱ間の配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"4箇所",
"2箇所",
"2箇所",
"3箇所",
"配線の余長はここに逃がすこと",
"最終確認:ﾍｯﾄﾞを左側ﾒｶｽﾄに当てた際に接触し無い事を確認",
"右側はﾓｰﾀ･ｴﾝｺｰﾀﾞ線(4本)を固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"手順:1",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"手順:3",
"ｲﾝｼｭﾛｯｸ(200mm)",
"手順:1",
"手順:2",
"手順:3",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"手順:2"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線処理1",
"WorkItems": [
"1. Y軸ｹｰﾌﾞﾙﾍﾞｱ配線をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"7本",
"14本の配線を真ん中分け",
"7本",
"ｲﾝｼｭﾛｯｸの頭は機械外側に向けること※可動部との干渉防止の為",
"配線/配管がｽﾄｯﾊﾟｰ角に押し当てられないよう注意して固定する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"15箇所",
"6箇所",
"外側",
"矢視A",
"矢視A"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾍﾞｱ配線処理2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "配線配管処理確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉､当り､引っ張り無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線処理3",
"WorkItems": [
"1. 架台左下に配線を引き回し固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"配線と架台の隙間を通す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･･･ﾓｰﾀ線",
"【XBK501】",
"･･･ｴﾝｺｰﾀﾞ線 ｶﾒﾗｹｰﾌﾞﾙ",
"【X5K501】【2K303】【HF_K313】【HFPWA11】",
"ｲﾝｼｭﾛｯｸ(100mm)",
"【X5K501】【2K303】【HF_K313】【HFPWA11】",
"【XBK501】"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線処理4",
"WorkItems": [
"1. 架台左内側に配線を引き回し固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"本体束線に沿わせながら整線する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･･･ﾓｰﾀ線",
"【XBK501】",
"･･･ｴﾝｺｰﾀﾞ線 ｶﾒﾗｹｰﾌﾞﾙ",
"【X5K501】【2K303】【HF_K313】【HFPWA11】",
"【2K303】【HF_K313】【HFPWA11】",
"【XBK501】",
"【X5K501】",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線処理5",
"WorkItems": [
"1. 架台左中心部に配線を引き回し固定する",
"■2. ｶﾒﾗｹｰﾌﾞﾙをCPU BOXに接続し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"R側から来た【4K303】も一緒に固定すること",
"ﾏﾙﾁｶﾒﾗに接続する配線を一緒に固定し無い事",
"配線の余長はここで丸めて吸収する事",
"※目安:直径100mm以上",
"【4K303】",
"【2K303】"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:5.CPU BOX - ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"【2K303】",
"【HF_K313】",
"【HFPWA11】",
"【4K303】",
"･･･R側ｶﾒﾗｹｰﾌﾞﾙ",
"【4K303】",
"･･･ｴﾝｺｰﾀﾞ線 ｶﾒﾗｹｰﾌﾞﾙ",
"【X5K501】【2K303】【HF_K313】【HFPWA11】",
"ｲﾝｼｭﾛｯｸ(150mm)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線処理5",
"WorkItems": [
"1. 架台左中心部に配線を引き回し固定する",
"■2. ｶﾒﾗｹｰﾌﾞﾙをCPU BOXに接続し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"R側から来た【4K303】も一緒に固定すること",
"ﾏﾙﾁｶﾒﾗに接続する配線を一緒に固定し無い事",
"配線の余長はここで丸めて吸収する事",
"※目安:直径100mm以上",
"【4K303】",
"【2K303】"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"【2K303】",
"【HF_K313】",
"【HFPWA11】",
"【4K303】",
"ｲﾝｼｭﾛｯｸ(200mm)",
"･･･R側ｶﾒﾗｹｰﾌﾞﾙ",
"【4K303】",
"･･･ｴﾝｺｰﾀﾞ線 ｶﾒﾗｹｰﾌﾞﾙ",
"【X5K501】【2K303】【HF_K313】【HFPWA11】",
"検査表①:5.CPU BOX - ｺﾈｸﾀ接続確認",
"ｲﾝｼｭﾛｯｸ(150mm)",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "FY軸ﾄﾞﾗｲﾊﾞｰ配線接続",
"WorkItems": [
"■1. FYM軸ﾄﾞﾗｲﾊﾞｰ配線を接続する",
"■2. FYS軸ﾄﾞﾗｲﾊﾞｰ配線を接続する",
"■1. FYM軸ﾄﾞﾗｲﾊﾞｰ配線を接続する",
"■2. FYS軸ﾄﾞﾗｲﾊﾞｰ配線を接続する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾌﾛﾝﾄ側",
"ﾌﾛﾝﾄ側",
"ﾌﾛﾝﾄ側"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FY軸ﾄﾞﾗｲﾊﾞｰ配線接続",
"WorkItems": [
"■1. FYM軸ﾄﾞﾗｲﾊﾞｰ配線を接続する",
"■2. FYS軸ﾄﾞﾗｲﾊﾞｰ配線を接続する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾌﾛﾝﾄ側"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"検査表①:4.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"【X5K502】",
"【XBK502】",
"【K502】 FYM軸ﾄﾞﾗｲﾊﾞｰ",
"【X5K506】",
"【XBK506】",
"【K506】 FYS軸ﾄﾞﾗｲﾊﾞｰ",
"【E2K502】",
"【E2K506】",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "FX軸ﾄﾞﾗｲﾊﾞｰ配線接続",
"WorkItems": [
"■1. FX軸ﾄﾞﾗｲﾊﾞｰ配線を接続する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"【X5K501】",
"【XBK501】",
"【E2K501】",
"【K501】FX軸ﾄﾞﾗｲﾊﾞｰ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FX軸ﾄﾞﾗｲﾊﾞｰ配線接続",
"WorkItems": [
"■1. FX軸ﾄﾞﾗｲﾊﾞｰ配線を接続する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認",
"【X5K501】",
"【XBK501】",
"【E2K501】",
"【K501】FX軸ﾄﾞﾗｲﾊﾞｰ",
"WEPJ-G002-D08"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D08",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰ束配管投入",
"WorkItems": [
"1. ①を投入する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"架台の中へ",
"架台の中へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【901】",
"【101】【801】【306】【307】【501】【502】【701】【702】【703】 他",
"【703】【704】【202】【302】【203】【206】【209】【307】",
"【701】【702】【201】【301】【202】",
"【205】",
"【208】【306】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "80cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ取付け",
"WorkItems": [
"1. 束配管ﾏﾆﾎｰﾙﾄﾞをBOLT WASHER WASHER にて取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"架台とﾏﾆﾎｰﾙﾄﾞの間にWASHER 厚肉ﾜｯｼｬｰを入れる"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. ①をSCREW で取付ける",
"2. USBｺﾈｸﾀをBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"LCRﾁｪｯｶｰ仕様時のみ作業実施"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"【216】 【217】",
"裏面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "25cN･m",
"WorkName": "台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [],
"WorkPoints": [
"取付け方向に注意する事",
"余長は架台内で丸めておく",
"取付け方向に注意する事(JST文字が上部)"
],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:LCR4 ﾌﾞﾗｹｯﾄ部接続確認(F/R共通)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. ①をSCREW で取付ける",
"2. USBｺﾈｸﾀをBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"取付け方向に注意する事",
"LCRﾁｪｯｶｰ仕様時のみ作業実施",
"余長は架台内で丸めておく",
"取付け方向に注意する事(JST文字が上部)"
],
"Tolks": [
"締付ﾄﾙｸ 25cN･m",
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"【216】 【217】",
"裏面",
"検査表①:LCR4 ﾌﾞﾗｹｯﾄ部接続確認(F/R共通)",
"WEPJ-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.