input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "7.5N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 7.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:部品確認",
"挿入1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "7.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み①",
"WorkItems": [],
"WorkPoints": [
"平行度:0.02㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸ﾎﾞｰﾙねじとLMｶﾞｲﾄﾞとの平行度 LMｶﾞｲﾄﾞとの芯振れ"
],
... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み②",
"WorkItems": [
"2. 1完成品ﾍﾞｱﾘﾝｸﾞに①を挿し込みBOLT で取付ける",
"3. ②のﾎﾞｰﾙﾈｼﾞ先端にRING をBOLT で取付ける",
"1. ②のﾎﾞｰﾙﾈｼﾞにBEARING C-RING を取付ける"
],
"WorkPoints": [
"押し当てて取付"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み③",
"WorkItems": [
"1. ①のﾎﾞｰﾙﾈｼﾞの芯振れを測定する"
],
"WorkPoints": [
"芯振れ測定:0.01㎜以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:MH軸ﾎﾞｰﾙねじとL... | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01m以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "7cN･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み③",
"WorkItems": [
"2. 1完成品のﾎﾞｰﾙねじの回転ﾄﾙｸを3か所測定する"
],
"WorkPoints": [
"①上側",
"②中央",
"③下側"
],
"Tolks": [
"回転ﾄﾙｸ:7cN･m以内"
],
"InspectionNo": "WWYJ-5300-057",
"In... | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品にCOUPLING を挿入し､①に... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品にCOUPLING を挿入し､①に... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "19.6N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [],
"WorkPoints": [
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "19.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [],
"WorkPoints": [
"芯出し手順1.ﾓｰﾀｰを原点位置(Z相｢00｣)にする2.ｶｯﾌﾟﾘﾝｸﾞの割りを下面にし固定する"
],
"Tolks": [
"締付ﾄﾙｸ 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "原点確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み④",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. 1完成品にLABEL TERMINAL PROCESS を取付ける",
"4. ﾓｰﾀｰとｶｯﾌﾟﾘﾝｸﾞの芯出しを行い､本締めする",
"◆5. ﾍﾞｰｽ､ﾓｰﾀｰﾌﾞﾗｹｯﾄの加工面すべてに金ﾆｽを塗る",
"3. 2完成品にCOUPLING を挿入し､①に... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "金ﾆｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_組込み⑤",
"WorkItems": [
"1. ①のﾍﾞｰｽにSENSOR をBOLT WASHER WASHER で取付ける",
"2. ①のﾌﾞﾛｯｸにDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_原点出し①",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"【MH軸原点出し手順】",
"1. ①のﾓｰﾀｰﾌﾞﾗｹｯﾄ側ｽﾄｯﾊﾟｰとﾎﾞｰﾙねじ間にﾌﾞﾛｯｸｹﾞｰｼﾞ(5mm)を挟み込む",
"2. 1の位置でRUFｾﾝｻｰの中心になるように①のｾﾝｻｰﾄﾞｸﾞ位置を調整する",
"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5.0㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"本締め",
"【MH軸原点出し手順】",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する"
],
"Tolks": [... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(24V_PFSS輸出用)",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"本締め",
"【MH軸原点出し手順】",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する"
... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "19.6N･m",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾓｰﾀｰ部_原点出し②",
"WorkItems": [
"1. ①のMH軸の原点出しを行う"
],
"WorkPoints": [
"本締め",
"【MH軸原点出し手順】",
"1.①のMH軸ﾓｰﾀｰに原点出し治具､ﾌﾞﾚｰｷ解除治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する"
],
"Tolks... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "19.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.3,0.5㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [],
"WorkPoints": [
"4㎜",
"CYLINDER 付属の小径ﾜｯｼｬｰを入れる事"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [],
"WorkTypes": [],
"Words... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.3,0.5㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [],
"WorkPoints": [
"4㎜",
"CYLINDER 付属の小径ﾜｯｼｬｰを入れる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "端面から4㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組立",
"WorkItems": [
"◆4. LEVER にｸﾞﾘｰｽを塗り､3完成品にPIN SCREW で取付ける",
"2. 1完成品のｼﾘﾝﾀﾞﾛｯﾄﾞ先端にBLOCK を取付ける",
"3. 2完成品にCYLINDER 付属ｾﾝｻｰとJOINT を取付ける",
"1. BLOCK にCYLINDER をBOLT で取付ける"
],
"WorkPoints": ... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸落下防止ｼﾘﾝﾀﾞ部_組込み",
"WorkItems": [
"1. ②にLABEL TERMINAL PROCESS を取付ける",
"2. ①に1完成品をSPACER BOLT で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MHV軸ｾﾝｻｰ部_組込み①",
"WorkItems": [
"2. ①のｽﾌﾟﾗｲﾝ先端部に1完成品をSCREW で取付ける",
"1. DOG にBRACKET をSCREW で取付ける"
],
"WorkPoints": [
"ｾﾝｻｰとの位置調整するため､仮取付にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MHV軸ｾﾝｻｰ部_組込み②",
"WorkItems": [],
"WorkPoints": [
"【MHV軸原点出し手順】",
"1.①のMHV軸ﾓｰﾀｰに原点出し治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"3. PHﾁｪｯｶｰで ORGｾﾝｻｰ がONする位置に①のｾﾝｻｰﾄﾞｸﾞを調整する",
"4. ... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MHV軸ｾﾝｻｰ部_組込み②",
"WorkItems": [],
"WorkPoints": [
"【MHV軸原点出し手順】",
"1.①のMHV軸ﾓｰﾀｰに原点出し治具を接続する",
"2. ﾓｰﾀｰを原点位置(Z相｢00｣にしｶｯﾌﾟﾘﾝｸﾞを固定する",
"3. PHﾁｪｯｶｰで ORGｾﾝｻｰ がONする位置に①のｾﾝｻｰﾄﾞｸﾞを調整する",
"4. 軸を左右に... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ｵｲﾙﾊﾟﾝ_組込み",
"WorkItems": [
"1. ①にOIL-PAN をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [
"◆1. BOLT BOLT BOLT に耐熱ｸﾞﾘｰｽを塗布する",
"4. 3完成品にBOLT NUT BOLT を取付ける",
"2. HOLDER にPIN を圧入する",
"3. HOLDER のｶｯﾌﾟﾘﾝｸﾞ部をBOLT で仮締めする"
],
"WorkPoints": [
"矢視A",
"仮締め:SD-A04... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [
"◆1. BOLT BOLT BOLT に耐熱ｸﾞﾘｰｽを塗布する",
"2. HOLDER にPIN を圧入する",
"3. HOLDER のｶｯﾌﾟﾘﾝｸﾞ部をBOLT で仮締めする"
],
"WorkPoints": [
"仮締め:SD-A044466-034にて本締め"
],
"Tolks": [],
"... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立①",
"WorkItems": [
"4. 3完成品にBOLT NUT BOLT を取付ける"
],
"WorkPoints": [
"前後左右4箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:14.0㎜±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立②",
"WorkItems": [
"2. ①にJOINT JOINT を取付ける",
"3. 2完成品にPLATE をBOLT で取付ける",
"◆1. JOINT JOINT BOLT ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"Inspe... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立③",
"WorkItems": [
"1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "10.0㎜±0.5㎜15.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立③",
"WorkItems": [
"◆2. BOLT ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"1. BRACKET にLABEL を貼付ける",
"3. ①に1完成品をBOLT WASHER で取付ける",
"4. 3.完成品に㉙200㎜を取付ける"
],
"WorkPoints": [
"15㎜",
"10㎜"
],
"Tolks": [],... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立④",
"WorkItems": [
"■1. HEATER THERMO-COUPLE の型式を確認し､ｼﾘｱﾙを検査表に記入する",
"2. 1完成品のHEATER THERMO-COUPLE にLABEL TERMINAL PROCESS を取付ける",
"◆3. SCREW ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"4. ①に2完成品を3完成品で取付ける"
],
"Work... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立④",
"WorkItems": [
"■1. HEATER THERMO-COUPLE の型式を確認し､ｼﾘｱﾙを検査表に記入する",
"2. 1完成品のHEATER THERMO-COUPLE にLABEL TERMINAL PROCESS を取付ける",
"◆3. SCREW ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"4. ①に2完成品を3完成品で取付ける"
],
"Work... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立④",
"WorkItems": [
"■1. HEATER THERMO-COUPLE の型式を確認し､ｼﾘｱﾙを検査表に記入する",
"2. 1完成品のHEATER THERMO-COUPLE にLABEL TERMINAL PROCESS を取付ける",
"◆3. SCREW ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"4. ①に2完成品を3完成品で取付ける"
],
"Work... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-057",
"InspectionItems": [
"検査表①:ﾋｰﾀｰの取付位置"
],
"WorkTypes": [],
"Words": [
"E11203P",
"検査表①:安全部品... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:14.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"E11203P",
"検査表①:安全部品確認",
"検査表①:高温部ﾎﾞﾙﾄへの耐熱ｸﾞﾘｰｽ塗布",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立⑤",
"WorkItems": [
"1. CABLE の型式･ｼﾘｱﾙNo.確認",
"◆2. BOLT BOLT ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"3. HOLDER にHOLDER SPACER CABLE をBOLT で取付ける",
"4. ①に3完成品をBOLT で取付ける",
"5. 4完成品をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立⑤",
"WorkItems": [
"1. CABLE の型式･ｼﾘｱﾙNo.確認",
"◆2. BOLT BOLT ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"3. HOLDER にHOLDER SPACER CABLE をBOLT で取付ける",
"4. ①に3完成品をBOLT で取付ける",
"5. 4完成品をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組立⑤",
"WorkItems": [
"1. CABLE の型式･ｼﾘｱﾙNo.確認",
"◆2. BOLT BOLT ﾈｼﾞ部に耐熱ｸﾞﾘｰｽを塗布する",
"3. HOLDER にHOLDER SPACER CABLE をBOLT で取付ける",
"4. ①に3完成品をBOLT で取付ける",
"5. 4完成品をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "WWYJ-5300-057",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組込み",
"WorkItems": [
"2. 1完成品のﾂｰﾙ平行度を測定する"
],
"WorkPoints": [
"平行度:0.01㎜以内",
"2.①のMHV軸ﾓｰﾀｰに原点出し治具を接続し原点位置にする",
"3.てこ式ダイヤルゲージで㉘治具ツール面の平行度を確認、調整し固定ボルトを本締めする",
"1.ヘッド先端部に㉘治具ツ... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "",
"ToolOther": "FM-3278",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ﾍｯﾄﾞ先端部_組込み",
"WorkItems": [
"2. 1完成品のﾂｰﾙ平行度を測定する"
],
"WorkPoints": [
"平行度:0.01㎜以内",
"2.①のMHV軸ﾓｰﾀｰに原点出し治具を接続し原点位置にする",
"3.てこ式ダイヤルゲージで㉘治具ツール面の平行度を確認、調整し固定ボルトを本締めする",
"1.ヘッド先端部に㉘治具ツールを取付ける",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-3278",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_真空ｾﾝｻｰ部_組立",
"WorkItems": [
"1. SWITCH にJOINT を取付け､BRACKET にBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_真空ｾﾝｻｰ部_組込み",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_ｸﾘｰﾝｹｰﾌﾞﾙ連結ﾌﾞﾗｹｯﾄ_組込み",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾎﾞｰﾙねじｶﾊﾞｰ_組込み",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"3. ①にCOVER をBOLT WASHER で取付ける",
"4. 2完成品に1完成品をSCREW WASHER で取付ける",
"■1. LABEL の形式を確認する"
],
"WorkPoints": [
"端に合わせる事(目視)"
],
"Tolks... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞ:M_(正流れ)_MH軸ﾎﾞｰﾙねじｶﾊﾞｰ_組込み",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の形式を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立①",
"WorkItems": [
"1. VALVE にAIR-FILTER JOINT を取付ける",
"2. VALVE にJOINT を取付ける",
"3. VALVE にJOINT を取付ける",
"4. VALVE にJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立②",
"WorkItems": [
"3. TUBE TUBE を指定の長さにｶｯﾄし③に取付ける",
"1. TUBE TUBE を指定の長さにｶｯﾄし①に取付ける",
"2. TUBE TUBE を指定の長さにｶｯﾄし②に取付ける",
"4. TUBE TUBE を指定の長さにｶｯﾄし④に取付ける",
"3. TUBE TUBE を指定の長さにｶｯﾄし③に取付ける... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立③",
"WorkItems": [
"1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [
"48㎜",
"1㎜",
"98㎜",
"1㎜",
"32㎜",
"47㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立④",
"WorkItems": [
"1. ①にREGULATOR をSCREW で取付ける",
"2. 1完成品にJOINT を取付ける",
"3. 2完成品に②③④⑤をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立⑤",
"WorkItems": [
"1. TUBE を下記の寸法にｶｯﾄする",
"2. ①にCABLE-SUPPORT を取付ける",
"3. 2完成品にJOINT をBOLT WASHER WASHER で取付ける",
"4. 3完成品に1完成品を接続する",
"6. 5完成品A配管とCABLE-SUPPORT をｲﾝｼｭﾛｯｸで結束する",
"5. ｴｱｰ配... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "200.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立⑤",
"WorkItems": [
"1. TUBE を下記の寸法にｶｯﾄする",
"2. ①にCABLE-SUPPORT を取付ける",
"3. 2完成品にJOINT をBOLT WASHER WASHER で取付ける",
"4. 3完成品に1完成品を接続する",
"6. 5完成品A配管とCABLE-SUPPORT をｲﾝｼｭﾛｯｸで結束する",
"5. ｴｱｰ配管A､... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_空圧部_組立⑥",
"WorkItems": [
"1. BRACKET にJOINT を取付ける",
"2. 1完成品にJOINT JOINT CABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_廃棄BOX部_組立①",
"WorkItems": [
"1. AIR CYLINDER にSPEED-CONTROLLER を取付ける",
"2. 1完成品にBRACKET を取付ける",
"3. 2完成品にAIR CYLINDER 付属ｹｰﾌﾞﾙを取付ける",
"4. 3完成品のｼﾘﾝﾀﾞｰﾛｯﾄにFLOATING-JOINT を取付ける",
"5. 4完成品にBRACKET を取付ける"
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から2回転開いてﾛｯｸ",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_廃棄BOX部_組立①",
"WorkItems": [
"4. 3完成品のｼﾘﾝﾀﾞｰﾛｯﾄにFLOATING-JOINT を取付ける",
"5. 4完成品にBRACKET を取付ける"
],
"WorkPoints": [
"3㎜",
"ｼﾘﾝﾀﾞｰﾛｯﾄのねじ込みは､底当たりしてから2回転戻した位置でﾛｯｸする事"
],
"Tolks": [],
"Insp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_廃棄BOX部_組立②",
"WorkItems": [
"1. ①にBRACKET をSCREW WASHER で取付ける",
"2. 1完成品にBOX を取付ける"
],
"WorkPoints": [
"はめ込みのみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_廃棄BOX部_組立③",
"WorkItems": [
"1. PLATE にRAIL をSCREW で取付ける",
"2. ①を1完成品のPLATE にBOLT WASHER で取付け､1完成品のRAIL にSCREW で連結する"
],
"WorkPoints": [
"4箇所",
"2箇所",
"RAIL ﾚｰﾙ側から締付けて連結"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ｺﾈｸﾀﾌﾞﾗｹｯﾄ部_組立",
"WorkItems": [
"1. BRACKET にCABLE をBOLT WASHER WASHER で取付ける",
"2. 1完成品にBRACKET をBOLT で取付ける",
"3. 2完成品のBRACKET にBOLT を取付ける"
],
"WorkPoints": [
"表面",
"裏面",
"熱電対ｺﾈｸﾀ取付け用"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_組込み①",
"WorkItems": [
"4. 3完成品にCLIP をBOLT で取付ける",
"1. ⑥に①をBOLT WASHER で取付ける",
"3. 2完成品に③をBOLT で取付ける",
"2. 1完成品に②をBOLT WASHER で取付ける",
"5. 4完成品に㉙を取付ける"
],
"WorkPoints": [
"参考図"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_組込み②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ空圧部_配管",
"WorkItems": [
"1. ①の正圧配管を下図の様に接続する",
"2. 1完成品の真空/吸着配管を下図の様に接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ｸﾘｰﾝｹｰﾌﾞﾙ_組込み",
"WorkItems": [
"1. ①のﾌﾞﾗｹｯﾄにCABLE をBOLT で取付ける"
],
"WorkPoints": [
"ｸﾘｰﾝｹｰﾌﾞﾙ取り扱い注意 ｸﾘｰﾝｹｰﾌﾞﾙはﾕﾆｯﾄ組立が完了するまでｴｱﾏｯﾄ等で保護する事 ※汚れが付くと浸み込む為取ることが出来ません"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ｸﾘｰﾝｹｰﾌﾞﾙﾍｯﾄﾞ側_配線",
"WorkItems": [
"1. ①ﾍｯﾄﾞ側の配線配管を引き回しする"
],
"WorkPoints": [
"コネクタブラケット⇐方向に挿し込み",
"ﾌﾞﾗｹｯﾄ裏側を引き回し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞ部_配線①",
"WorkItems": [
"2. 熱電対ｺﾈｸﾀをBOLT で固定する",
"■3. ｱｰｽ線をSCREW で固定する",
"■1. ①ﾍｯﾄﾞ側の配線配管を引き回し接続する"
],
"WorkPoints": [
"ｶｯﾄした配管を2股ｼﾞｮｲﾝﾄの下側に接続",
"ｶｯﾄし2股ｼﾞｮｲﾝﾄの上側に接続"
],
"Tolks": [
... | {
"QualityItem": "配線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞ部_配線①",
"WorkItems": [
"2. 熱電対ｺﾈｸﾀをBOLT で固定する",
"■3. ｱｰｽ線をSCREW で固定する",
"■1. ①ﾍｯﾄﾞ側の配線配管を引き回し接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞ部_配線②",
"WorkItems": [
"1. ①ﾍｯﾄﾞ先端部の吸着配管を接続する"
],
"WorkPoints": [
"ﾍｯﾄﾞ先端部(MHV軸)を手動でﾌﾙｽﾄﾛｰｸ回して配線配管の干渉が無いことを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞ部_配線③",
"WorkItems": [
"2. の1完成品の配線配管を引き回しする",
"■1. ①ｾﾝｻにCABLE を接続する"
],
"WorkPoints": [
"仮引き回し:SD-A044666-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)/ｲｵﾅｲｻﾞｰ_組込み",
"WorkItems": [
"1. ①に⑪を㉓BOLT で取付け、⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)/ｲｵﾅｲｻﾞｰ_配線",
"WorkItems": [
"1. 1完成品の配線配管を引き回し接続する"
],
"WorkPoints": [
"H-BOX",
"仮引き回し:SD-A044466-064にて束線",
"①空圧部ﾌﾞﾗｹｯﾄの開口部を通して後部へ引き回し"
],
"Tolks": [],
"InspectionNo": "WWXJ-5300-086",
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-086",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_廃棄BOX部_配線",
"WorkItems": [
"1. ①廃棄BOX部の配線配管を引き回しする"
],
"WorkPoints": [
"仮引き回し:SD-A044666-065にて束線､接続",
"空圧部の配管を廃棄BOXｼﾘﾝﾀﾞへ引き回し",
"廃棄BOXｼﾘﾝﾀﾞ配線を上部へ引き回し"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ空圧部_配線",
"WorkItems": [
"1. ①ﾍｯﾄﾞﾍﾞｰｽ空圧部の配線を引き回し､CABLE CABLE を接続する"
],
"WorkPoints": [
"仮引き回し:SD-A044466-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ｸﾘｰﾝｹｰﾌﾞﾙﾍｯﾄﾞﾍﾞｰｽ側_配線",
"WorkItems": [
"1. ①ﾍｯﾄﾞﾍﾞｰｽ側の配線配管を引き回しする"
],
"WorkPoints": [
"①ﾍｯﾄﾞ側ﾌﾞﾗｹｯﾄ裏図",
"仮引き回し:SD-A044466-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_配管",
"WorkItems": [
"1. TUBE TUBE TUBE を下記の寸法にｶｯﾄする",
"2. ①に1完成品とJOINT を接続し引き回しする",
"3. 2完成品をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにSD-44466-60の 34aK001、11bK001とCABLE CABLE CABLE を取付け、㉙で結束する"
],... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにSD-44466-60の 34aK001、11bK001とCABLE CABLE CABLE を取付け、㉙で結束する"
],... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "0.9N･m",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:接続確認",
"検査表①:型式... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.9N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにSD-44466-60の 34aK001、11bK001とCABLE CABLE CABLE を取付け、㉙で結束する"
],... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_配線",
"WorkItems": [
"1. ①ｺﾈｸﾀﾌﾞﾗｹｯﾄにCABLE CABLE CABLE CABLE CABLE CABLE CABLE を取付け､引き回し結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(正流れ)_ﾍｯﾄﾞ部、ﾍｯﾄﾞﾍﾞｰｽ部_配線",
"WorkItems": [
"2. ①ﾍｯﾄﾞ部､ﾍｯﾄﾞﾍﾞｰｽ部の配線配管を引き回し接続する",
"1. ①にCABLE を接続する",
"3. BOLT は2完成品に添付し次工程(本体ﾄﾞｯｷﾝｸﾞ)に引渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC廃棄ﾎﾞｯｸｽ組立",
"WorkItems": [
"2. 1.完成品にKNOB WASHER を取付ける",
"1. BRACKET にBOX をSCREW WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明(TCP専用対応)組立①",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認しｼﾘｱﾙ番号を検査書に記入する",
"2. LED LIGHTING UNIT にOPTICAL-FILTER を隙間のないように当付けて組付ける",
"3. BRACKET に2の完成品を組付ける",
"4. BRACKET に3の完成品をBOLT WASHER で組付ける"
],
"WorkPoi... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明(TCP専用対応)組立①",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認しｼﾘｱﾙ番号を検査書に記入する",
"2. LED LIGHTING UNIT にOPTICAL-FILTER を隙間のないように当付けて組付ける",
"3. BRACKET に2の完成品を組付ける",
"4. BRACKET に3の完成品をBOLT WASHER で組付ける"
],
"WorkPoi... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-086",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "TCP認識照明(TCP専用対応)組立①",
"WorkItems": [],
"WorkPoints": [
"0.02㎜以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LED LIGHTING UNIT :安全部品確認",
"検査表LED LI... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.02㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "TCP認識照明(TCP専用対応)組立①",
"WorkItems": [
"3. BRACKET に2の完成品を組付ける",
"4. BRACKET に3の完成品をBOLT WASHER で組付ける"
],
"WorkPoints": [
"拡散ﾌｨﾙﾀ上面からﾌﾞﾗｹｯﾄ下面までの高さを50㎜で調整",
"ｹｰﾌﾞﾙは右側に出るように取付け"
],
"Tolks": [],
"InspectionN... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:50㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明(TCP専用対応)組立②",
"WorkItems": [
"1. SPACER SPACER を2本連結させる(2ｾｯﾄ)",
"2. 1.完成品､③BOLT WASHER ､BRACKET BOLT WASHER を本体工程へ引き渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾊﾟｯﾄﾞ取付",
"WorkItems": [
"1. 各吸着ﾊﾝﾄﾞにVACUUM-PAD を取付"
],
"WorkPoints": [
"吸着ﾊﾝﾄﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"▲2. 1.完成品にSPACER SPACER SPACER をBOLT WASHER BOLT WASHER BOLT ADHESIVE で組付け",
"1. BRACKET にLABEL を指定の寸法で貼付け"
],
"WorkPoints": [
"SPACER SPACER SPACER は裏面から固定",
"ﾛｯｸﾀｲﾄはSPACER のみ"
],
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"▲2. 1.完成品にSPACER SPACER SPACER をBOLT WASHER BOLT WASHER BOLT ADHESIVE で組付け",
"1. BRACKET にLABEL を指定の寸法で貼付け"
],
"WorkPoints": [
"SPACER SPACER SPACER は裏面から固定",
"ﾛｯｸﾀｲﾄはSPACER のみ"
],
"Tolks... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"▲2. 1.完成品にSPACER SPACER SPACER をBOLT WASHER BOLT WASHER BOLT ADHESIVE で組付け",
"1. BRACKET にLABEL を指定の寸法で貼付け"
],
"WorkPoints": [
"SPACER SPACER SPACER は裏面から固定",
"ﾛｯｸﾀｲﾄはSPACER のみ"
],
"Tolks... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立②",
"WorkItems": [
"2. 1.完成品にCABLE-SUPPORT を挿入",
"1. ①にVALVE MANIFOLD MANIFOLD をBOLT WASHER BOLT WASHER BOLT で組付け"
],
"WorkPoints": [
"締めすぎに注意の事(板金が曲がる)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立③",
"WorkItems": [
"2. 1.完成品にPLATE をBOLT WASHER で組付け",
"1. ①にBRACKET SENSOR JOINT をBOLT WASHER BOLT WASHER WASHER BOLT で組付け"
],
"WorkPoints": [
"SENSOR はBRACKET に組付け"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立①",
"WorkItems": [
"3. 1.完成品にLINEAR-WAY の基準ﾚｰﾙをBOLT でﾋﾟﾝに当付けで組付け",
"1. PLATE にPIN ･LINEAR-WAY をBOLT で組付け",
"2. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立①",
"WorkItems": [
"3. 1.完成品にLINEAR-WAY の基準ﾚｰﾙをBOLT でﾋﾟﾝに当付けで組付け",
"1. PLATE にPIN ･LINEAR-WAY をBOLT で組付け",
"2. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録",
"Dﾋﾟﾝ押し当ての事"
],... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立①",
"WorkItems": [
"3. 1.完成品にLINEAR-WAY の基準ﾚｰﾙをBOLT でﾋﾟﾝに当付けで組付け",
"1. PLATE にPIN ･LINEAR-WAY をBOLT で組付け",
"2. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録",
"Dﾋﾟﾝ押し当ての事"
],... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立②",
"WorkItems": [
"2. ①にLINEAR-WAY をBOLT で基準ﾚｰﾙに平行に組付け",
"1. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録",
"片側Dﾋﾟﾝに当付けで平行を調整",
"平行度 0.02mm以下",
"LINEAR-... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立②",
"WorkItems": [
"2. ①にLINEAR-WAY をBOLT で基準ﾚｰﾙに平行に組付け",
"1. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録",
"片側Dﾋﾟﾝに当付けで平行を調整",
"平行度 0.02mm以下",
"LINEAR-WAY ｽﾗｲﾄﾞは組付け後元に戻す... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立②",
"WorkItems": [
"2. ①にLINEAR-WAY をBOLT で基準ﾚｰﾙに平行に組付け",
"1. LINEAR-WAY の型式を確認し､ｼﾘｱﾙ番号を検査書に記載"
],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録",
"片側Dﾋﾟﾝに当付けで平行を調整",
"平行度 0.02mm以下",
"LINEAR-WAY ｽﾗｲﾄﾞは組付け後元に戻す... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "ﾓﾝｷｰ",
"ToolOther": "9.0N･m",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立③",
"WorkItems": [],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 9.0N･m",
"ﾎﾞｰﾙﾈｼﾞ"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立③",
"WorkItems": [
"2. BALL-SCREW にSUPPORT-UNIT のｶﾗｰ･ｻﾎﾟｰﾄﾕﾆｯﾄ･ｶﾗｰ･ﾅｯﾄの順で挿入",
"1. BALL-SCREW の型式を確認し､ｼﾘｱﾙ番号を検査書に記載",
"3. 2.完成品のﾅｯﾄをﾄﾙｸｽﾊﾟﾅで締付､ﾅｯﾄをｾｯﾄﾋﾟｰｽ･ｾｯﾄﾋﾞｽで固定",
"4. 3.完成品にSUPPORT-UNIT のﾍﾞｱﾘﾝｸﾞを挿入しCﾘﾝｸﾞで固定後､ｻ... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立③",
"WorkItems": [
"2. BALL-SCREW にSUPPORT-UNIT のｶﾗｰ･ｻﾎﾟｰﾄﾕﾆｯﾄ･ｶﾗｰ･ﾅｯﾄの順で挿入",
"1. BALL-SCREW の型式を確認し､ｼﾘｱﾙ番号を検査書に記載",
"3. 2.完成品のﾅｯﾄをﾄﾙｸｽﾊﾟﾅで締付､ﾅｯﾄをｾｯﾄﾋﾟｰｽ･ｾｯﾄﾋﾞｽで固定",
"4. 3.完成品にSUPPORT-UNIT のﾍﾞｱﾘﾝｸﾞを挿入しCﾘﾝｸﾞで固定後､ｻ... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立④",
"WorkItems": [
"2. ﾎﾞｰﾙﾈｼﾞの芯振れを測定し検査書に記入",
"1. ①に②をBOLT でﾋﾟﾝに当付けで組付け"
],
"WorkPoints": [
"Dﾋﾟﾝに押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 9.0N･m"
],
"InspectionNo": "WWYJ-5300-087",
"In... | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02m以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "ﾓﾝｷｰ",
"ToolOther": "9.0N･m",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立④",
"WorkItems": [
"2. ﾎﾞｰﾙﾈｼﾞの芯振れを測定し検査書に記入",
"1. ①に②をBOLT でﾋﾟﾝに当付けで組付け"
],
"WorkPoints": [
"Dﾋﾟﾝに押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 9.0N･m"
],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.