input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK のDｶｯﾄの位置に注意して取付ける事",
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOL... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ組立17連/34連(LCRﾁｪｯｶｰ仕様)",
"WorkItems": [
"1. COVER にLABEL を貼付ける",
"2. JOINT を払い出す"
],
"WorkPoints": [
"気泡無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ準備1",
"WorkItems": [
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝを立ち上げる",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝを立ち上げる",
"1. ﾄﾚｲ配線とﾁｪｯｶｰの配線･配管を接続する",
"3. ﾁｪｯｶｰの電源をONする",
"4. ﾄﾚｲ本体の電源をONし､ｴｱｰ圧を確認する"
],
"WorkPoints": [
"ﾓﾆﾀｰ電源SW",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ準備1",
"WorkItems": [
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝを立ち上げる",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝを立ち上げる",
"1. ﾄﾚｲ配線とﾁｪｯｶｰの配線･配管を接続する",
"3. ﾁｪｯｶｰの電源をONする",
"4. ﾄﾚｲ本体の電源をONし､ｴｱｰ圧を確認する"
],
"WorkPoints": [
"ﾓﾆﾀｰ電源SW",
... | {
"QualityItem": "圧力確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5MPaである事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ準備2",
"WorkItems": [
"2. 検査員を選択し『OK』を押す",
"3. ﾕﾆｯﾄｼﾘｱﾙﾗﾍﾞﾙのQRｺｰﾄﾞをｽｷｬﾝし『OK』を押す",
"1. PCが立ち上がったら『NPM-GWﾄﾚｲ』をﾀﾞﾌﾞﾙｸﾘｯｸする",
"3. ﾕﾆｯﾄｼﾘｱﾙﾗﾍﾞﾙのQRｺｰﾄﾞをｽｷｬﾝし『OK』を押す",
"1. PCが立ち上がったら『NPM-GWﾄﾚｲ』をﾀﾞﾌﾞ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ準備3",
"WorkItems": [
"1. PnP情報書込み内容が表示されるので『書込み』を押す",
"2. PnP情報を書込みますと表示されるので『OK』を押す",
"3. PnP情報書込み終了と表示されるので『OK』を押す",
"4. 自動運転の画面が表示されるので『通信ｺﾏﾝﾄﾞ』を押す"
],
"WorkPoints": [],
"Tolks": [],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給完了SW・ﾌｧﾝｱﾗｰﾑ確認",
"WorkItems": [],
"WorkPoints": [
"FANｺﾈｸﾀ(G101R)",
"FANｺﾈｸﾀ(G101R)",
"FANｺﾈｸﾀ(G101R)"
],
"Tolks": [],
"InspectionNo": "WETE-G002-B03",
"InspectionItems": [
"検査表①:I/Oﾁ... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾏｶﾞｼﾞﾝﾄﾞｱ開確認",
"WorkItems": [
"1. ｱｸﾁｭｴｰﾀを近づけた時､『ﾏｶﾞｼﾞﾝﾄﾞｱSW』が水色表示になる事を確認する",
"2. ｱｸﾁｭｴｰﾀを離すと黒色表示になる事を確認する",
"1. ｱｸﾁｭｴｰﾀを近づけた時､『ﾏｶﾞｼﾞﾝﾄﾞｱSW』が水色表示になる事を確認する",
"2. ｱｸﾁｭｴｰﾀを離すと黒色表示になる事を確認する"
],
"Wor... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸±OVRｾﾝｻ確認",
"WorkItems": [
"1. TL軸+OVERｾﾝｻを遮光すると『TL軸+OVER』が黒色表示になる事を確認する",
"2. TL軸-OVERｾﾝｻを遮光すると『TL軸-OVER』が黒色表示になる事を確認する",
"1. TL軸+OVERｾﾝｻを遮光すると『TL軸+OVER』が黒色表示になる事を確認する",
"2. TL軸-OVERｾﾝｻを遮光すると『TL軸-... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部ｼｬｯﾀｰ確認1",
"WorkItems": [
"1. 『補給部ｼｬｯﾀｰ閉』を押す",
"2. 補給部ｼｬｯﾀｰ閉と表示されるので『OK』を押す",
"3. 補給部ｼｬｯﾀｰ閉『B1315』が水色表示､補給部ｼｬｯﾀｰ開閉『R402』が水色表示になる事を確認する",
"1. 『補給部ｼｬｯﾀｰ閉』を押す",
"2. 補給部ｼｬｯﾀｰ閉と表示されるので『OK』を押す",
... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部ｼｬｯﾀｰ確認2",
"WorkItems": [
"2. 補給部ｼｬｯﾀｰ開と表示されるので『OK』を押す",
"1. 『補給部ｼｬｯﾀｰ開』を押す",
"3. 補給部ｼｬｯﾀｰ開『B1314』が水色表示､補給部ｼｬｯﾀｰ開閉『R402』が黒色表示になる事を確認する"
],
"WorkPoints": [
"上下動作が問題なければ､出力の補給部ｼｬｯﾀｰ(R402)もOKとする... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻ・補給ﾄﾞｱSW確認",
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し有無ｾﾝｻを遮光すると『B1301』が黒色表示になる事を確認する",
"2. 補給部のﾄﾞｱSWを押した時『S02』が水色表示になる事を確認する"
],
"WorkPoints": [
"ﾊﾟﾚｯﾄはみだし有無",
"ﾊﾟﾚｯﾄはみだし有無ｾﾝｻ:B1301",
"補給ﾄ... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "引き出し軸ﾊﾟﾚｯﾄ有無確認",
"WorkItems": [
"1. 引き出し軸ﾊﾟﾚｯﾄ有無(ﾏｶﾞｼﾞﾝ側)を遮光すると『B1303』が黒色表示になる事を確認する",
"2. 引き出し軸ﾊﾟﾚｯﾄ有無(吸着側)を遮光すると『B1304』が黒色表示になる事を確認する",
"1. 引き出し軸ﾊﾟﾚｯﾄ有無(ﾏｶﾞｼﾞﾝ側)を遮光すると『B1303』が黒色表示になる事を確認する",
"2. 引き出... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "吸着部高さ確認、TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無確認",
"WorkItems": [
"2.TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻを遮光すると『B1302』が黒色表示になる事を確認する",
"1. 吸着部高さｾﾝｻを遮光すると『B1305』が水色表示になる事を確認する",
"2.TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻを遮光すると『B1302』が黒色表示になる事を確認する",
"1. 吸着部高さｾ... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸±OVRｾﾝｻ確認",
"WorkItems": [],
"WorkPoints": [
"A矢視",
"-OVRｾﾝｻ:B1323",
"+OVRｾﾝｻ:B1322",
"A矢視",
"-OVRｾﾝｻ:B1323",
"+OVRｾﾝｻ:B1322"
],
"Tolks": [],
"InspectionNo": "WETE-G002-B03",
... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸引き出し位置ｾﾝｻ確認",
"WorkItems": [
"1. TP軸引き出し位置ｾﾝｻを遮光すると『B1324』が黒色表示になる事を確認する",
"2. TP軸引き出し位置ｾﾝｻ2を遮光すると『B1325』が黒色表示になる事を確認する",
"1. TP軸引き出し位置ｾﾝｻを遮光すると『B1324』が黒色表示になる事を確認する",
"2. TP軸引き出し位置ｾﾝｻ2を遮光すると『B1325... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉確認",
"WorkItems": [
"1. 『ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開』を押す",
"3. 『ﾏｶﾞｼﾞﾝ右側/左側ｼｬｯﾀ-開』が水色表示､ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉『R401』が水色表示になる事を確認する",
"1. 『ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開』を押す",
"3. 『ﾏｶﾞｼﾞﾝ右側/左側ｼｬｯﾀ-開』が水色表示､ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉『R401』が水色表示に... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉確認2",
"WorkItems": [
"1. 『ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉』を押す",
"3. 『ﾏｶﾞｼﾞﾝ右側/左側ｼｬｯﾀ閉』が水色表示､ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉『R401』が黒色表示になる事を確認する",
"1. 『ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉』を押す",
"3. 『ﾏｶﾞｼﾞﾝ右側/左側ｼｬｯﾀ閉』が水色表示､ﾏｶﾞｼﾞﾝｼｬｯﾀｰ開閉『R401』が黒色表示にな... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給完了SW点灯確認",
"WorkItems": [
"1. 『補給完了SW点灯』を押す",
"2. 補給完了SW点灯と表示されるので『OK』を押す",
"2. 補給完了SW点灯と表示されるので『OK』を押す",
"5. 補給完了SW消灯と表示されるので『OK』を押し､消灯を確認する",
"5. 補給完了SW消灯と表示されるので『OK』を押し､消灯を確認する"
],
"Wo... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸ確認",
"WorkItems": [
"1. 『ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸ閉』を押す",
"3. ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸが指示通り動作している事を確認する",
"2. ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸ閉と表示されるので『OK』を押し､ｼﾘﾝﾀﾞを確認する",
"4. 『ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸ開』を押す",
"5. ﾏｶﾞｼﾞﾝﾄﾞｱﾛｯｸ開と表示されるので『OK』を押... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "安全状態確認・安全ｺﾝﾄﾛｰﾗﾘｾｯﾄ確認",
"WorkItems": [
"1. 『ｾｰﾌﾃｨﾘﾚｰﾘｾｯﾄ』を押す",
"3. 安全状態確認が水色表示と､ﾏｸﾞﾈｯﾄｺﾝﾀｸﾀの接点が『ON』になっている事を確認する",
"4. ﾏｶﾞｼﾞﾝﾄﾞｱを開けると安全状態確認が黒色表示と､ﾏｸﾞﾈｯﾄｺﾝﾀｸﾀの接点が『OFF』になっている事を確認する",
"1. 『ｾｰﾌﾃｨﾘﾚｰﾘｾｯﾄ』を押... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "MBR信号確認1",
"WorkItems": [
"1. 『異常解除要求』を押す",
"3. 『ｾｰﾌﾃｨﾘﾚｰﾘｾｯﾄ』を押す",
"2. 異常解除要求と表示されるので『OK』を押す",
"1. 『異常解除要求』を押す",
"3. 『ｾｰﾌﾃｨﾘﾚｰﾘｾｯﾄ』を押す",
"2. 異常解除要求と表示されるので『OK』を押す",
"1. 『異常解除要求』を押す",
... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "MBR信号確認2",
"WorkItems": [
"1. 『ｻｰﾎﾞﾏｽｸ解除』を押す",
"2. ｻｰﾎﾞﾏｽｸ解除と表示されるので『OK』を押す",
"1. 『ｻｰﾎﾞﾏｽｸ解除』を押す",
"2. ｻｰﾎﾞﾏｽｸ解除と表示されるので『OK』を押す",
"1. 『ｻｰﾎﾞﾏｽｸ解除』を押す",
"2. ｻｰﾎﾞﾏｽｸ解除と表示されるので『OK』を押す"
],
... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ｻｰﾎﾞON・VTSU付ﾄﾚｲﾕﾆｯﾄ判別ﾋﾞｯﾄ確認",
"WorkItems": [
"1. 『SUB』を押しVTSU付ﾄﾚｲﾕﾆｯﾄ判別が黒色表示の事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-B03",
"InspectionItems": [
"検査表①:I/Oﾁｪｯｸ",
"... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GW_ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "安全ｺﾝﾄﾛｰﾗｰON確認",
"WorkItems": [
"1. 非接触式ﾄﾞｱSWｺﾝﾄﾛｰﾗ電源が供給されている事を確認する",
"2. 確認終了後全ての治具の電源を落とし､ｴｱｰ供給を切断する事"
],
"WorkPoints": [
"電源供給されている事で安全ｺﾝﾄﾛｰﾗ ON 確認はOKとする",
"LEDが点灯している事"
],
"Tolks": [],
... | {
"QualityItem": "I/O確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りにON/OFFする事",
"Method": "目視",
"RecordMethod": "WETE-G002-B03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"T... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. 『起動』をｸﾘｯｸする",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"1. Xﾋﾞｰﾑをﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰ~ﾘｱﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞｰﾑを移動後は動かさ無い事(信号調整Startの開始位置にな... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾘｱ側に動かす",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"2. Xﾋﾞｰﾑをﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰ~ﾘｱﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"3. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [
"Scale A:min40max80... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸②_信号Monitor1",
"WorkItems": [
"4. 『終了』を押す",
"1. 『信号Monitor』をｸﾘｯｸする",
"3. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する",
"2. Xﾋﾞｰﾑをﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰ~ﾘｱﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸②_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾘｱ側に動かす",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸②_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸②_信号Monitor2",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"2. Xﾋﾞｰﾑをﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰ~ﾘｱﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"3. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [
"Scale A:min40max80... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①②_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"1. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"3. 『F側SET』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差測定1",
"WorkItems": [
"1. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『偏差測定』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑを押し【0(ｾﾞﾛ)】付近に移動する",
"4. 3の位置にて『ﾃﾞｰﾀ取込』をｸﾘｯｸする(PCの『Enterｷｰ』でも可)"
],
"WorkPoints": [],
"Tolks": [],
"Insp... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差測定2",
"WorkItems": [
"1. Xﾋﾞｰﾑを100㎜づつ移動させ､都度『ﾃﾞｰﾀ取込』をｸﾘｯｸする",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"移動誤差は±10㎜以内にする事",
"100㎜~1000㎜まで計10回取り込む"
],
"Tolks... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差設定",
"WorkItems": [
"1. 『偏差設定』をｸﾘｯｸする",
"2. 『F側SET』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰ(ﾘｱXﾋﾞｰﾑを押す)に当てる"
],
"WorkPoints": [
"Y軸①: -66.4㎜ ~ -66.0㎜ / Y軸②: 66.0㎜ ~ 66.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①-664㎜~-66.0㎜②66.0㎜~66.4㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰ(ﾘｱXﾋﾞｰﾑを押す)に当てる"
],
"WorkPoints": [
"Y軸①: -66.4㎜ ~ -66.0㎜ / Y軸②: 66.0㎜ ~ 66.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①1117㎜~(1243.2㎜)②(-1243.2㎜)~-1117㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①②_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 完了ﾗﾝﾌﾟ点灯を確認し､『終了』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tolks": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"2. 『起動』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へX軸を移動する"
],
"WorkPoints": [
"最大値の位置へX軸を移動後は動かさ無い事(信号調整Startの開始位置になる為)"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､X軸を右側に動かす",
"4. 【信号を確認します】が表示されたら､X軸を左側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上移動させる事",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号Moni... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:min40max80 / Scale B:m... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"3. 『F-X』をｸﾘｯｸする",
"4. 原点ﾌﾟﾘｾｯﾄ値に【 8.0000 】が表示されたら『SET』をｸﾘｯｸする",
"5. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(−)側ｽﾄﾛｰｸ規格値:7.8㎜~8.2㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(+)側ｽﾄﾛｰｸ規格値:968㎜~970㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tol... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. 『起動』をｸﾘｯｸする",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する",
"1. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞｰﾑを移動後は動かさ無い事(信号調整Startの開始位置になる為... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾘｱ側に戻す",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に動かす"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号M... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸をﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"OKを確認",
"OKを確認",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号Monitor1",
"WorkItems": [
"4. 『終了』を押す",
"1. 『信号Monitor』をｸﾘｯｸする",
"3. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する",
"2. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞｰﾑ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に動かす",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾘｱ側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号M... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号Monitor2",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"4. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"Scale A:min40max80 / S... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①②_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸする",
"1. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. 『R側SET』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差測定1",
"WorkItems": [
"2. 『偏差測定』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑを押し【0(ｾﾞﾛ)】付近に移動する",
"4. 3の位置にて『ﾃﾞｰﾀ取込』をｸﾘｯｸする(PCの『Enterｷｰ』でも可)",
"1. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [],
"Tolks": [],
"Inspecti... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差測定2",
"WorkItems": [
"1. Xﾋﾞｰﾑを100㎜づつ移動させ､都度『ﾃﾞｰﾀ取込』をｸﾘｯｸする",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"移動誤差は±10㎜以内にする事",
"100㎜~1000㎜まで計10回取り込む"
],
"Tolks": [... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差設定",
"WorkItems": [
"1. 『偏差設定』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. 『R側SET』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"3. ﾘｱXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰ(ﾌﾛﾝﾄXﾋﾞｰﾑを押す)に当てる",
"2. ﾘｱXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"Y軸①: -126.4㎜ ~ -126.0㎜ / Y軸②: 126.0㎜ ~ 126.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①-126.4㎜~-126.0㎜②126.0㎜~126.4㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"3. ﾘｱXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰ(ﾌﾛﾝﾄXﾋﾞｰﾑを押す)に当てる",
"2. ﾘｱXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"Y軸①: -126.4㎜ ~ -126.0㎜ / Y軸②: 126.0㎜ ~ 126.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①1117㎜~(1183.2㎜)②(-1183.2㎜)~-1117㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①②_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 完了ﾗﾝﾌﾟ点灯を確認し､『終了』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"T... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"2. 『起動』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へX軸を移動する"
],
"WorkPoints": [
"最大値の位置へX軸を移動後は動かさ無い事(信号調整Startの開始位置になる為)"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､X軸を右側に動かす",
"4. 【信号を確認します】が表示されたら､X軸を左側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上移動させる事",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号Monito... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:min40max80 / Scale B:min... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"3. 『F-X』をｸﾘｯｸする",
"4. 原点ﾌﾟﾘｾｯﾄ値に【 8.0000 】が表示されたら『SET』をｸﾘｯｸする",
"5. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾘｱX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾘｱX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
"Tol... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(−)側ｽﾄﾛｰｸ規格値:7.8㎜~8.2㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾘｱX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾘｱX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
"Tol... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(+)側ｽﾄﾛｰｸ規格値:968㎜~970㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に②③を④⑯⑰⑱⑲で取付",
"締付ﾄﾙｸ 194cN･m",
"下方向に当付けて取付",
"※赤線で示す箇... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.6N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"青線部分は端面合わせで取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付",
"WorkItems": [
"1. COVER にLABEL を貼付"
],
"WorkPoints": [
"2mm",
"5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBRACKET(L) をBOLT で取付"
],
"WorkPoints": [
"青線部当てつけ、㉘が入ら無い事",
"㉙付属のねじM10x35で取付",
"①重量物(17kg)運搬は二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBRACKET(L) をBOLT で取付"
],
"WorkPoints": [
"青線部当てつけ、㉘が入ら無い事",
"㉙付属のねじM10x35で取付",
"①重量物(17kg)運搬は二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"2. １完成品を㉙に取付"
],
"WorkPoints": [
"1完成品をDﾋﾟﾝに合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.