input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "台車ｶﾞｲﾄﾞ位置調整ｼﾞｸﾞ(NPM-GH)",
"Size": "",
"ToolOther": "FM-6549",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6549",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "台車ｶﾞｲﾄﾞ位置調整ｼﾞｸﾞ(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEPJ-G002-C20",... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②を⑯⑰で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "39.0±0.5㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ⑥に①を⑯⑰⑱⑲で取付",
"締付ﾄﾙｸ 194cN･m",
"締付... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ⑥に①を⑯⑰⑱⑲で取付",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 19... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ⑥に①を⑯⑰⑱⑲で取付",
"締付ﾄﾙｸ 95cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK を矢印方向に㉙に押し当て",
"黄線部㉚が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部ﾌﾞﾛｯｸ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6400",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK を矢印方向に㉙に押し当て",
"黄線部㉚が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6400",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部ﾌﾞﾛｯｸ位置決めｼﾞｸﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK を矢印方向に㉙に押し当て",
"黄線部㉚が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK を矢印方向に㉙に押し当て",
"黄線部㉚が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK を矢印方向に㉙に押し当て",
"黄線部㉚が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品(H1工程)",
"WorkItems": [
"1. ①BOLT BOLT WASHER BOLT BOLT WASHER ㉒をH1工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認①:『動作ｽｲｯﾁ設定』",
"WorkItems": [
"1. 装着ﾍｯﾄﾞの調整/ｷｬﾘﾌﾞが終了している事",
"2. ①『ﾎｰﾑ』を選択する",
"3. ②『ｻｰﾋﾞｽｴﾝｼﾞﾆｱ』をONにする",
"4. ③『動作ｽｲｯﾁ』を選択",
"5. ④『荷重ﾁｪｯｶｰF･R』､『実負荷(分銅)校正機能』を選択",
"6. ①『ﾎｰﾑ』を選択し⑤『はい』を選択",
"7.... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認②:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』",
"WorkItems": [
"3. ③『荷重ﾁｪｯｶｰ』を選択",
"1. ①『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択",
"2. ②『第4工程』を選択",
"4. ④『荷重ﾁｪｯｶｰ位置測定』を選択する",
"5. 指定されたﾉｽﾞﾙを準備･ｾｯﾄし⑤を選択する",
"6. ⑥『正常に終了しました』の表示が出ていることを確認",
"7. ⑦『ﾒﾝﾃ... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "完了出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具分銅ｷｯﾄ",
"Size": "5N",
"ToolOther": "MTKA041625AA",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認③:『出力荷重確認1』",
"WorkItems": [
"1. ①『調整』を選択",
"2. ②『荷重ﾁｪｯｶｰ』を選択",
"3. ③『実荷重計測』を選択",
"4. ④『ｼﾞｸﾞ取付け』を選択",
"5. ｻﾎﾟｰﾄ治具をｾｯﾄし⑤『確認』を選択"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合は... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具分銅ｷｯﾄ分銅ｷｯﾄ分銅ｷｯﾄ",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認④:『出力荷重確認2』",
"WorkItems": [
"1. 計測する①『0.5N』を選択し､②『計測ｽﾀｰﾄ』を選択する",
"2. 分銅を取付③『実行』を選択する",
"3. 分銅を取外し④『確認』を選択",
"4. ①『分銅』→1N､5Nそれぞれ作業項目1~4を実施"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認④:『出力荷重確認2』",
"WorkItems": [
"1. 計測する①『0.5N』を選択し､②『計測ｽﾀｰﾄ』を選択する",
"2. 分銅を取付③『実行』を選択する",
"3. 分銅を取外し④『確認』を選択",
"4. ①『分銅』→1N､5Nそれぞれ作業項目1~4を実施"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯ... | {
"QualityItem": "荷重確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.5N:±0.11.0N:±0.15.0N:±0.3",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑤:『動作確認1』",
"WorkItems": [
"1. ①｢機種切替｣を選択",
"2. ②｢生産ﾃﾞｰﾀ選択｣を選択",
"3. 下記注記が表示されるので③｢確認｣を選択",
"4. ④｢簡易ﾃﾞｰﾀ生成｣を選択",
"5. ⑤｢ｵﾌｾｯﾄ反映｣を選択",
"6. ⑥『1005』を選択",
"7. ⑦『ﾉｽﾞﾙ種別230､1001』を選択",
"8. ⑧｢読... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑥:『動作確認2』",
"WorkItems": [
"1. ①『ﾍｯﾄﾞ』を選択する",
"2. ②で指定されたﾉｽﾞﾙを準備する",
"3. ﾁｪﾝｼﾞｬｰにﾉｽﾞﾙをｾｯﾄしﾏｼﾝにｾｯﾄする",
"4. ③『交換』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑥:『動作確認2』",
"WorkItems": [
"1. ①『ﾍｯﾄﾞ』を選択する",
"2. ②で指定されたﾉｽﾞﾙを準備する",
"3. ﾁｪﾝｼﾞｬｰにﾉｽﾞﾙをｾｯﾄしﾏｼﾝにｾｯﾄする",
"4. ③『交換』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "完了出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑦:『動作確認3』",
"WorkItems": [
"1. ①『ﾒﾝﾃﾅﾝｽ』を選択する",
"2. ②『ﾍｯﾄﾞ』を選択する",
"6. ⑥NGになっていないことの確認",
"3. ③『装着荷重計測』を選択する",
"4. ④『全選択』を選択する",
"5. ⑤『計測ｽﾀｰﾄ』を選択する",
"7. 確認後､ﾉｽﾞﾙを外す"
],
"WorkPoints": ... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "警告における上限値・下限値以内である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り1",
"WorkItems": [
"■1. ANALYZER の型式を確認する",
"■2. ANALYZER の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の型式を確認する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表ANALY... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り2",
"WorkItems": [
"1. ①②のｽｲｯﾁを設定する"
],
"WorkPoints": [
"B2004",
"B2005",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF"
],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り3",
"WorkItems": [
"■1. SENSOR SENSOR SENSOR SENSOR SENSOR の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表SENSOR :APD.1 型式確認"
],
"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り4",
"WorkItems": [
"1. ①②③を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰを下げてﾛｯｸする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "55cN･m",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B200... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B2004",
"B9_B2004"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り6",
"WorkItems": [
"1. ①にJOINT JOINT JOINT を取付ける"
],
"WorkPoints": [
"ﾒｲﾝｴｱ圧用ﾃﾞｼﾞﾀﾙｹﾞｰｼﾞに接続された配管を外してJOINT に接続する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｱﾅﾗｲｻﾞ取付け",
"WorkItems": [
"1. RAIL にTERMINAL-BLOCK を取付ける",
"2. 1完成品をBOLT WASHER で架台に取付ける",
"3. ③を取付ける"
],
"WorkPoints": [
"上側を引掛け矢印方向に押して取付ける",
"ﾚｰﾙ端面に合わせて取付けのこと",
"矢印方向に当付け取付けのこと",
"上側を引掛け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "ｾｰﾌﾃｨｺﾝﾄﾛｰﾗ取付け",
"WorkItems": [
"1. TERMINAL-SUPPORT を取付ける",
"3. TERMINAL-BLOCK を取付ける",
"4. ｹｰﾌﾞﾙを固定する",
"2. ｾｰﾌﾃｨｺﾝﾄﾛｰﾗを取付ける"
],
"WorkPoints": [
"矢印方向に当付け取付けのこと",
"矢印方向に当付け取付けのこと"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 配線を引き回し固定する"
],
"WorkPoints": [
"B130/1/2/3/4P",
"CX1221TM3R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭ... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し・接続",
"WorkItems": [
"★1. CABLE を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"MTKC036462"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"★静電対策作業",
"■安全作業"
],
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し・接続",
"WorkItems": [
"★1. CABLE を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"MTKC036462"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表CABLE :APD.6 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. 配線を引き回し固定する"
],
"WorkPoints": [
"B130/1/2/3/4P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞ... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧ｾﾝｻｰ接続",
"WorkItems": [
"1. 各ｾﾝｻｰを接続する"
],
"WorkPoints": [
"B131P",
"B132P",
"B133P",
"B130P",
"B134P",
"SD-EJM8EB1-611で配線した各空圧ｾﾝｻｰを接続する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"I... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｰ切替ﾊﾞﾙﾌﾞ・ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部配管接続",
"WorkItems": [
"1. ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部の配管を接続し､配管を固定する"
],
"WorkPoints": [
"配管折れに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Wo... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｺｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立①",
"WorkItems": [
"1. BRACKET に油砥石かけ"
],
"WorkPoints": [
"指定箇所に油砥石をかける",
"油砥石かけ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [... | {
"QualityItem": "脱脂確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所が脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立①",
"WorkItems": [
"1. BRACKET に油砥石かけ"
],
"WorkPoints": [
"指定箇所に油砥石をかける",
"油砥石かけ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. 1の完成品へLABEL を指定... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆2個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. 1の完成品へLABEL を指定... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:各1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立③",
"WorkItems": [
"1. ①にPIN を圧入"
],
"WorkPoints": [
"PIN の出代10mm",
"PIN の圧入方向､場所に注意(下図参照)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安出代:10㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "切替台座部(支持部側)組立③",
"WorkItems": [
"2. 1の完成品にCOLLAR BOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立④",
"WorkItems": [
"1. ①にPLATE ③④を取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "切替台座部(支持部側)組立④",
"WorkItems": [
"1. ①にPLATE ③④を取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑤",
"WorkItems": [
"1. ①にBOLT WASHER を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"BOLT WASHER を挿入してから②を取付する事",
"ﾎﾞﾙﾄの出代調整の為WASHER を2枚入れる",
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "切替台座部(支持部側)組立⑤",
"WorkItems": [
"1. ①にBOLT WASHER を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"BOLT WASHER を挿入してから②を取付する事",
"ﾎﾞﾙﾄの出代調整の為WASHER を2枚入れる",
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑥",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ①にBOLT を挿入し､②をBOLT WASHER で取付",
"BOLT を挿入してから②を取付する事",
... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "切替台座部(支持部側)組立⑥",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ①にBOLT を挿入し､②をBOLT WASHER で取付",
"BOL... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ①にCAP を挿入"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑧",
"WorkItems": [
"◆1. ①のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け"
],
"WorkPoints": [
"各銘板の貼付け向きに注意(下図参照)",
"3mm",
"3mm",
"3mm",
"3mm",
"4mm",
"ﾗﾍﾞﾙ貼付け面"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "脱脂確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所が脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑧",
"WorkItems": [
"◆1. ①のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け"
],
"WorkPoints": [
"各銘板の貼付け向きに注意(下図参照)",
"3mm",
"3mm",
"3mm",
"3mm",
"4mm",
"ﾗﾍﾞﾙ貼付け面"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "貼付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. BRACKET へLINEAR-SCALE (S/N $$$$$$$$-02)をBOLT WASHER で取付ける",
"3. BRACKET へLINEAR-SCALE (S/N ********-01)をBOLT WASHER で取付ける",
"1. LINEAR-SCALE LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を記入する"
],
"WorkPoin... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. BRACKET へLINEAR-SCALE (S/N $$$$$$$$-02)をBOLT WASHER で取付ける",
"1. LINEAR-SCALE LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を記入する",
"3. BRACKET へLINEAR-SCALE (S/N ********-01)をBOLT WASHER で取付ける... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"2. Yフレームに㉖を置いてMOTOR を置く"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事"... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-3046",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者側な... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事",
"型式確認､ｼﾘｱﾙNo.記入"... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-3046",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者側な... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)①",
"WorkItems": [
"◆1. MOTOR を㉖へ表示通りにセットする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)①",
"WorkItems": [
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする",
"◆1. MOTOR を㉖へ表示通りにセットする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6607",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6607",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付③",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)④",
"WorkItems": [
"◆1. MOTOR を②へ表示通りにｾｯﾄする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする",
"◆1. MOTOR を②へ表示通りにｾｯﾄする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)④",
"WorkItems": [
"◆1. MOTOR を②へ表示通りにｾｯﾄする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ保護ｼﾞｸﾞ(中央取付用)",
"Size": "",
"ToolOther": "FM-6605",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6605",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付⑥",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)⑦",
"WorkItems": [
"◆1. MOTOR を㉖へ表示通りにセットする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)⑦",
"WorkItems": [
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする",
"◆1. MOTOR を㉖へ表示通りにセットする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ保護ｼﾞｸﾞ(ﾘｱ側取付用)",
"Size": "",
"ToolOther": "FM-6606",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6606",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付⑨",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付(右側)",
"WorkItems": [
"1. 本体に①②COVER をSCREW で取付ける"
],
"WorkPoints": [
"･上側ｶﾊﾞｰ:上に押し付け取付ける事･下側ｶﾊﾞｰ:固定金具取付穴に合わせ､Yﾌﾚｰﾑと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸固定子簡易保護ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-3050",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付(右側)",
"WorkItems": [
"1. 本体に①②COVER をSCREW で取付ける"
],
"WorkPoints": [
"･上側ｶﾊﾞｰ:上に押し付け取付ける事･下側ｶﾊﾞｰ:固定金具取付穴に合わせ､Yﾌﾚｰﾑと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3050",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5858",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [
"3. ヘッドカメラプレートの位置決めピンを㉘に押し当て締結する"
],
"WorkPoints": [
"マルチカメラ搭載付近に㉘をセットする",
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 1.9N･m"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5858",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words":... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [
"3. ヘッドカメラプレートの位置決めピンを㉘に押し当て締結する"
],
"WorkPoints": [
"マルチカメラ搭載付近に㉘をセットする"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "FM-6090",
"ToolOther": "3.6N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [
"3. ヘッドカメラプレートの位置決めピンを㉘に押し当て締結する"
],
"WorkPoints": [
"マルチカメラ搭載付近に㉘をセットする"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"Tolks": [
... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"To... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表②:... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LED照明の下面よりも下方向に垂れ下がら無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT 2 :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT 2 :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"Tolks... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT 2 :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT 2 :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LED照明の下面よりも下方向に垂れ下がら無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付③",
"WorkItems": [
"1. CLIP をBOLT で取付ける"
],
"WorkPoints": [
"OP;高さｾﾝｻ仕様がある場合はCLIP BOLT 取付不要"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する",
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表CABLE :... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.