input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "前段取り2",
"Words": [],
"WorkItems": [
"■2. NOISE-FILTER の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"■1. CIRCUIT-PROTECTOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する"
],
"WorkPoints": [
"この部分の番号を記入する",
"この部分の番号を記入する",
"この部分の... | [
{
"WorkName": "前段取り2",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "前段取り3",
"Words": [],
"WorkItems": [
"■1. POWER-SUPPLY POWER-SUPPLY の型式をﾁｪｯｸし､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"この部分の型式を確認する",
"この部分の番号を記入する",
"T102",
... | [
{
"WorkName": "前段取り3",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "前段取り4",
"Words": [],
"WorkItems": [
"■1. MAGNET-CONTACTOR MOTOR-DRIVER の型式をﾁｪｯｸし､ｼﾘｱﾙNoを検査表に記入する",
"2. MOTOR-DRIVER の設定を確認する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"この部分の型式を確認する"... | [
{
"WorkName": "前段取り4",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "前段取り5",
"Words": [],
"WorkItems": [
"■1. CONTROLLER の型式をﾁｪｯｸし､ｼﾘｱﾙNoを検査表に記入する",
"2. CONTROLLER の各種設定を確認する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"裏側",
"設定:OFF",
"設定:0",... | [
{
"WorkName": "前段取り5",
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "配線前段取り1",
"Words": [],
"WorkItems": [
"1. CABLE CABLE の配線に③④のｺﾈｸﾀを取付ける"
],
"WorkPoints": [
"端子の凸凹面を裏にする"
],
"Tolks": [],
"InspectionItems": [
"検査表①:4-2.ﾓｰﾀﾄﾞﾗｲﾊﾞ接続確認"
],
"InspectionNos":... | [
{
"WorkName": "配線前段取り1",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "配線前段取り2",
"Words": [],
"WorkItems": [
"1. CABLE の配線に②のｺﾈｸﾀを取付ける",
"2. CABLE にLABEL を取付ける"
],
"WorkPoints": [
"B側に取付けの事",
"OPTK301",
"CN1AK401",
"取付け方向に注意する事",
"端子の凸凹面を裏にする"
],
... | [
{
"WorkName": "配線前段取り2",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "CP前組み1",
"Words": [],
"WorkItems": [
"3. 2完成品にCABLE-SUPPORT COVER を取付ける",
"■1. BRACKET にLABEL LABEL を貼付ける",
"2. 1完成品に④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"20㎜",
"4㎜",
"27㎜",
"49.... | [
{
"WorkName": "CP前組み1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "CP前組み2",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. CABLE を指示通りの位置にﾏｰｷﾝｸﾞする",
"■2. 1完成品を①に接続し､CABLE とFG線をSCREW で取付け配線を固定する"
],
"WorkPoints": [
"... | [
{
"WorkName": "CP前組み2",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ前組み",
"Words": [],
"WorkItems": [
"3. 2完成品にCLIP をBOLT で取付ける",
"2. 1完成品にBRACKET BRACKET BRACKET をBOLT WASHER で取付ける",
"1. BRACKET に②をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N... | [
{
"WorkName": "ﾄﾞﾗｲﾊﾞｰ前組み",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "基板前組み1",
"Words": [],
"WorkItems": [
"2. 1完成品にLABEL を貼付ける",
"■1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [
"2.5㎜",
"表面",
"24.5㎜",
"45㎜",
"20㎜",
"20㎜",
"18㎜",
"32㎜",
... | [
{
"WorkName": "基板前組み1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "基板前組み2",
"Words": [],
"WorkItems": [
"1. ①にSPACER をSCREW で取付ける",
"2. 1完成品にSPACER を取付ける"
],
"WorkPoints": [
"目安出代:2.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionI... | [
{
"WorkName": "基板前組み2",
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "基板前組み3",
"Words": [],
"WorkItems": [
"★1. ①に②③をSCREW で取付ける",
"★2. 1完成品にSCREW SPACER CLIP SCREW を取付ける"
],
"WorkPoints": [
"目安出代:3㎜"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 80cN･m",
"締付... | [
{
"WorkName": "基板前組み3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "基板前組み4",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"★1. ①にCABLE ⑦CABLE を接続し配線を固定する"
],
"WorkPoints": [
"CN-PASSK301",
"CN-HEAD2K301",
"CN-INK3... | [
{
"WorkName": "基板前組み4",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾊﾟﾜｰｻﾌﾟﾗｲ前組み",
"Words": [],
"WorkItems": [
"1. PLATE に②③をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 49cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
... | [
{
"WorkName": "ﾊﾟﾜｰｻﾌﾟﾗｲ前組み",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "49cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾊﾟﾜｰｻﾌﾟﾗｲ配線接続",
"Words": [],
"WorkItems": [
"■1. ①にCABLE CABLE CABLE CABLE CABLE を接続する"
],
"WorkPoints": [
"ET102",
"-V1aT102",
"-V2aT102",
"+V1aT102",
"+V2aT102",
"AC(L)aT102",
... | [
{
"WorkName": "ﾊﾟﾜｰｻﾌﾟﾗｲ配線接続",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "下面ﾌﾞﾗｹｯﾄ組立",
"Words": [],
"WorkItems": [
"1. BRACKET にSPACER をBOLT WASHER NUT で取付ける",
"3. 2完成品にCABLE-SUPPORT を取付ける",
"2. 1完成品にSPACER SPACER SPACER SPACER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"To... | [
{
"WorkName": "下面ﾌﾞﾗｹｯﾄ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ取付け",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"■2. 1完成品にCABLE CABLE CABLE を接続する"
],
"WorkPoints": [
"刻印位置に注意する事",
"4aV001",
"3aV001",
"2aV001",
"1aV001",
... | [
{
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立1",
"Words": [],
"WorkItems": [
"3. 2完成品にSPACER SPACER をWASHER BOLT で取付ける",
"■1. BRACKET にLABEL を貼付ける",
"2. 1完成品にBRACKET をBOLT WASHER で取付ける",
"4. 3完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints... | [
{
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立2",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT WASHER WASHER で取付ける",
"3. 2完成品にTERMINAL-SUPPORT を取付ける",
"2. 1完成品にRAIL をBOLT WASHER で取付ける",
"4. 3完成品にTERMINAL-SUPPORT ⑤を取付ける"
],
"WorkPoints":... | [
{
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "130cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立3",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"■1. ①にCABLE CABLE CABLE を接続し､配線の引き回し･固定を行う"
],
"WorkPoints": [
"A2aQ201",
"22aQ201",
... | [
{
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立4",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①にCONNECTOR をSCREW で取付ける",
"■2. 1完成品に⑥⑦を接続する",
"■3. 2完成品にCABLE をSCREW で取付け､配線の接続･固定をする"
],... | [
{
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立4",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立5",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①にCABLE を接続し固定する"
],
"WorkPoints": [
"T33K101",
"T32K101",
"T31K101",
"D1K101... | [
{
"WorkName": "後面ﾌﾞﾗｹｯﾄ組立5",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立1",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"2. 1完成品にBRACKET をWASHER BOLT で取付ける",
"3. 2完成品にCABLE-SUPPORT を取付ける",
... | [
{
"WorkName": "BOX組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立2",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"■2. 1完成品の配線とCABLE を接続し固定する",
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"Dx201",
"+VaT1... | [
{
"WorkName": "BOX組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立3",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"■1. ①にCABLE を引き回し､ｱｰｽ線をTERMINAL にSCREW で固定する",
"2. 1完成品の配線を固定する"
],
"WorkPoints": [
"AC線とDC線を左右... | [
{
"WorkName": "BOX組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "T101・T102電圧調整",
"Words": [],
"WorkItems": [
"1. ①のｺﾈｸﾀAX211を抜き､治具ｺﾈｸﾀを接続する",
"2. 治具の電源を接続しAC入力電圧を測定する",
"3. T101･T102の電圧を調整し､検査表に記入する",
"4. 治具の電源を落としｺﾈｸﾀを抜き､AX211のｺﾈｸﾀを接続する"
],
"WorkPoints": [
... | [
{
"WorkName": "T101・T102電圧調整",
"QualityItem": "接続確認",
"ToolManageNo": "FM-5166",
"ToolName": "ﾄﾚｲ制御BOX電源供給ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "導通確認",
"Words": [],
"WorkItems": [
"■1. ①のT101ｱｰｽ~E2X001の導通確認を行い､検査表に記入する",
"■2. ①のT102ｱｰｽ~E4X001の導通確認を行い､検査表に記入する"
],
"WorkPoints": [
"判定値:0Ω~0.10Ω",
"判定値:0Ω~0.10Ω"
],
"Tolks": [],
"Insp... | [
{
"WorkName": "導通確認",
"QualityItem": "導通確認",
"ToolManageNo": "-",
"ToolName": "ﾏﾙﾁﾃｽﾀｰ",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "0~0.1Ω",
"Method": "ﾏﾙﾁﾃｽﾀｰ",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立4",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"2. ﾌﾞﾗｹｯﾄにｺﾈｸﾀを取付け､配線を固定する"
],
"WorkPoints": [
"1S310P",
"1TRA... | [
{
"WorkName": "BOX組立4",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立5",
"Words": [],
"WorkItems": [
"1. CABLE を指示通りの位置にﾏｰｷﾝｸﾞする",
"■★2. 1完成品のFG線をSCREW で固定する"
],
"WorkPoints": [
"290㎜",
"120㎜",
"FGS"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"Insp... | [
{
"WorkName": "BOX組立5",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立6",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"★1. ①②の配線を引き回し･接続し､配線を固定する"
],
"WorkPoints": [
"CN24VK302",
"CN-HEADK302",
"CN5K302",
... | [
{
"WorkName": "BOX組立6",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D32",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立7",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"■★2. 1完成品にCABLE を接続し固定する"
],
"WorkPoints": [
"CN3K401",
"E1K40... | [
{
"WorkName": "BOX組立7",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立8",
"Words": [],
"WorkItems": [
"1. ①に②を接続し､ｺﾈｸﾀをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"CNP3AK401",
"ｺﾈｸﾀにﾅｯﾄを挿入する",
"『AMP』表示が見える様固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"... | [
{
"WorkName": "BOX組立8",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立9",
"Words": [],
"WorkItems": [
"1. ①に②COVER をBOLT WASHER で取付ける",
"2. 1完成品にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"面を合わせて取付けの事",
"面を合わせて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
... | [
{
"WorkName": "BOX組立9",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "BOX組立10",
"Words": [],
"WorkItems": [
"■1. ①の入力電源を接続し､ｱｰｽ線をSCREW で固定する"
],
"WorkPoints": [
"E16",
"E11",
"電源線はｱｰｽ線の後側を通しておく事",
"2aF101",
"4aF101"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"... | [
{
"WorkName": "BOX組立10",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾁｪｯｶｰ作業準備1",
"Words": [],
"WorkItems": [
"1. ①に治具のｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CN29/30/32/33/34",
"CN10/17",
"CN1",
"CN29",
"CN30",
"CN32",
"CN33",
"CN34",
"CN10",
... | [
{
"WorkName": "ﾁｪｯｶｰ作業準備1",
"QualityItem": "接続確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾁｪｯｶｰ作業準備2",
"Words": [],
"WorkItems": [
"1. ①に治具のｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CN10/17",
"CN1",
"M401R",
"CN2A/BK401",
"CNP3BK401",
"USB",
"CNP3BK401",
"CN2A",
"CN2... | [
{
"WorkName": "ﾁｪｯｶｰ作業準備2",
"QualityItem": "接続確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾌｧｰﾑｳｴｱ確認",
"Words": [],
"WorkItems": [
"2. 『NPM-GH ﾄﾚｲ制御BOXﾁｪｯｶｰ』を起動する",
"1. 治具ﾊﾟｿｺﾝ･ﾁｪｯｶｰ･制御BOXのCPの電源をONする",
"3. 検査員を選択し『OK』をｸﾘｯｸする",
"4. 『ﾃﾞﾊﾞｯｸ⇒ﾌｧｰﾑｳｴｱ書込み』をｸﾘｯｸする",
"5. 『読み出し』をｸﾘｯｸする",
"6.... | [
{
"WorkName": "ﾌｧｰﾑｳｴｱ確認",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み1",
"Words": [],
"WorkItems": [
"1. 『検査開始』をｸﾘｯｸする",
"2. ｼﾘｱﾙNo.を入力し『OK』をｸﾘｯｸする",
"3. 下記指示が表示されるので『OK』をｸﾘｯｸする",
"4. 下記画面が表示されたらﾀｽｸﾊﾞｰの『MR Cpnfigurator2』を起動する"
],
"WorkPoints": [
... | [
{
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み1",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み2",
"Words": [],
"WorkItems": [
"1. 『ﾌﾟﾛｼﾞｪｸﾄ⇒新規作成』をｸﾘｯｸする",
"2. 下記設定にして『OK』をｸﾘｯｸする",
"3. ﾌﾟﾛｼﾞｪｸﾄを閉じてもよろしいですか？ と表示されるので『はい』をｸﾘｯｸする",
"4. ｻｰﾎﾞｱﾝﾌﾟからﾊﾟﾗﾒｰﾀを読み出し、ﾌﾟﾛｼﾞｪｸﾄを作成しますか? と表示される... | [
{
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み2",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み3",
"Words": [],
"WorkItems": [
"3. 再度PA08 ｵｰﾄﾁｭｰﾆﾝｸﾞﾓｰﾄﾞを選択し『選択項目書込み』をｸﾘｯｸする",
"1. PA08 ｵｰﾄﾁｭｰﾆﾝｸﾞﾓｰﾄﾞに『0001』を入力する",
"2. 1度他の項目を選択する",
"4. 選択した枠内のﾊﾟﾗﾒｰﾀを書込みますか？ と表示されるので『はい』をｸﾘｯｸする",
... | [
{
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み3",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み4",
"Words": [],
"WorkItems": [
"1. 下記設定にして『OK』をｸﾘｯｸする",
"2. ﾌﾟﾛｼﾞｪｸﾄを閉じてもよろしいですか？ と表示されるので『はい』をｸﾘｯｸする",
"3. ﾌﾟﾛｼﾞｪｸﾄは変更されています。保存しますか？と表示されるので 『いいえ』をｸﾘｯｸする",
"4. ｻｰﾎﾞｱﾝﾌﾟからﾊﾟﾗﾒｰﾀを読み出し... | [
{
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み4",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み5",
"Words": [],
"WorkItems": [
"3. 再度PA08 ｵｰﾄﾁｭｰﾆﾝｸﾞﾓｰﾄﾞを選択し『選択項目書込み』をｸﾘｯｸする",
"1. PA08 ｵｰﾄﾁｭｰﾆﾝｸﾞﾓｰﾄﾞに『0001』を入力する",
"2. 1度他の項目を選択する",
"4. 選択した枠内のﾊﾟﾗﾒｰﾀを書込みますか？ と表示されるので『はい』をｸﾘｯｸする",
... | [
{
"WorkName": "ｻｰﾎﾞｱﾝﾌﾟﾊﾟﾗﾒｰﾀ書込み5",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "TL軸・TP軸動作確認",
"Words": [],
"WorkItems": [
"1. 下記指示が表示されるので『OK』をｸﾘｯｸする",
"2. 検査が正常終了すると下記指示が表示されるので 『OK』をｸﾘｯｸし指示に従って作業する",
"3. 『終了』をｸﾘｯｸしｿﾌﾄを終了する"
],
"WorkPoints": [
"上記『OK』をｸﾘｯｸすると治具のﾓｰﾀｰが動作するので異... | [
{
"WorkName": "TL軸・TP軸動作確認",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾄﾚｲ制御BOX)) NPM-G Serirs (001-035）",
"WorkName": "ﾁｪｯｶｰ取外し",
"Words": [],
"WorkItems": [
"1. 『MR Cpnfigurator2』の『×』をｸﾘｯｸする",
"2. ﾌﾟﾛｼﾞｪｸﾄを閉じてもよろしいですか？ と表示されるので『はい』をｸﾘｯｸする",
"3. ﾌﾟﾛｼﾞｪｸﾄは変更されています。保存しますか？と表示されるので 『いいえ』をｸﾘｯｸする",
"4. 治具ﾊﾟｿｺﾝの電源をOFFする",
... | [
{
"WorkName": "ﾁｪｯｶｰ取外し",
"QualityItem": "作業確認",
"ToolManageNo": "FM-6214",
"ToolName": "NPM-GH_ﾄﾚｲ制御BOXﾁｪｯｶ-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾓｰﾀ組立",
"Words": [
"1.8mm",
"ﾓｰﾀとﾌﾟｰﾘの隙間;1.8mm",
"②と③のｽﾘｯﾄを合わせる事",
"隙間無い事",
"ﾃｰﾊﾟ面",
"ﾃｰﾊﾟ面"
],
"WorkItems": [
"2. MOTOR へCOUPLING PULLEY をBOLT で取付ける",
"■1. 型式確認､ｼﾘｱﾙ№記入"
]... | [
{
"WorkName": "ﾓｰﾀ組立",
"QualityItem": "型式確認･ｼﾘｱﾙNo.記録",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､及びｼﾘｱﾙNo.記録",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C33",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ組立",
"Words": [
"幅が狭い",
"OR",
"OR"
],
"WorkItems": [
"1. BLOCK へSPACER BEARING (ORBEARING )をBOLT で取付ける"
],
"WorkPoints": [
"BLOCK をﾊﾞｲｽで固定し締結する"
],
"Tolks": [
"締付ﾄﾙ... | [
{
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "TL軸ｾﾝｻｰ組立",
"Words": [
"押し付け",
"平行に取付ける事"
],
"WorkItems": [
"1. PLATE へSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"SENSOR は上に押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
... | [
{
"WorkName": "TL軸ｾﾝｻｰ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "給油部組立①",
"Words": [],
"WorkItems": [
"1. BLOCK へSCREW を挿入する",
"2. 1の完成品へGREASE-NIPPLE を挿入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],... | [
{
"WorkName": "給油部組立①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "給油部組立②",
"Words": [
"押し付け"
],
"WorkItems": [
"1. ①へJOINT を挿入する",
"2. 1の完成品へBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET は上に押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
... | [
{
"WorkName": "給油部組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "前面ﾌﾟﾚｰﾄ組立",
"Words": [
"割り方向",
"割り方向",
"出代:5mm±0.5㎜",
"押し付け",
"押し付け/丸穴ｾﾝﾀｰ",
"押し付け/丸穴ｾﾝﾀｰ"
],
"WorkItems": [
"2. 1の完成品へDOG DOG をBOLT WASHER で取付ける",
"1. PLATE へSPRING-PIN を圧入する... | [
{
"WorkName": "前面ﾌﾟﾚｰﾄ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾎﾞｰﾙﾈｼﾞ組立①",
"Words": [],
"WorkItems": [
"1. TUBE を指定長さにｶｯﾄする",
"2. JOINT へTUBE を挿入する",
"3. BALL-SCREW へ2の完成品を取付ける"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記録",
"2の完成品は上に向けて取付ける事",
"125mm"
... | [
{
"WorkName": "ﾎﾞｰﾙﾈｼﾞ組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾎﾞｰﾙﾈｼﾞ組立②",
"Words": [],
"WorkItems": [
"2. ④へ1の完成品をBOLT で仮取付けする",
"1. BLOCK へCLIP をBOLT で取付ける"
],
"WorkPoints": [
"CLIP は図の方向に向けて取付ける事",
"SD-A041321-022にて本締め"
],
"Tolks": [
"締付ﾄﾙｸ... | [
{
"WorkName": "ﾎﾞｰﾙﾈｼﾞ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "上部ﾌﾞﾛｯｸ組立",
"Words": [
"座ｸﾞﾘ側に挿入する事"
],
"WorkItems": [
"1. BLOCK へSPACER STOPPER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos... | [
{
"WorkName": "上部ﾌﾞﾛｯｸ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "下部ﾌﾞﾛｯｸ組立①",
"Words": [
"ｸﾞﾘｰｽ塗布:空間容積の30%~40%",
"ﾏｰｸ面を合わせる"
],
"WorkItems": [
"2. 1の完成品をBLOCK へ挿入しPLATE をBOLT WASHER で仮取付けする",
"◆1. BEARING へ㉖を塗布する"
],
"WorkPoints": [
"BEARING のﾏｰｸ面側か... | [
{
"WorkName": "下部ﾌﾞﾛｯｸ組立①",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "空間容積の30%~40%",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "下部ﾌﾞﾛｯｸ組立②",
"Words": [],
"WorkItems": [
"1. ①へSPACER STOPPER WASHER SPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Wo... | [
{
"WorkName": "下部ﾌﾞﾛｯｸ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "下部ﾌﾞﾛｯｸ組立③",
"Words": [
"8mm"
],
"WorkItems": [
"1. SPACER へSCREW を挿入する",
"2. ①へ1の完成品とCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
... | [
{
"WorkName": "下部ﾌﾞﾛｯｸ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾌﾚｰﾑ組立",
"Words": [
"出代:5mm±0.5mm",
"出代:6mm±0.5mm",
"出代:4mm±0.5mm"
],
"WorkItems": [
"1. FRAME へPIN PIN PIN を圧入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"Inspect... | [
{
"WorkName": "ﾌﾚｰﾑ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立①",
"Words": [
"締結②",
"締結①",
"締結③",
"締結④",
"隙間無い事"
],
"WorkItems": [
"1. ①FRAME ③④をBOLT BOLT で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"図の順番に締結する事"
],
... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立①",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4835",
"ToolName": "ﾘﾌﾄ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立②",
"Words": [
"D-PINとの隙間無い事",
"測定面",
"D-PINへ押し付け"
],
"WorkItems": [
"1. LINEAR-WAY の防錆油を拭き取る",
"2. ②へ1の完成品をBOLT で取付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞﾌﾞﾛｯｸ基準面(加工面)",
"型式確... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4835",
"ToolName": "ﾘﾌﾄ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立③",
"Words": [
"㉖へ押し付け",
"㉖へ押し付け",
"測定面"
],
"WorkItems": [
"2. ㉖を取り外す",
"1. ①へLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"従属側平行度;0.02㎜以下",
"ｽﾗｲﾄﾞﾌﾞﾛｯｸ基準面(加工面)"
],... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立③",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4835",
"ToolName": "ﾘﾌﾄ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立④",
"Words": [
"240mm",
"190mm",
"210mm",
"95mm"
],
"WorkItems": [
"1. TUBE を指定長さにｶｯﾄする",
"2. ②へJOINT を取付けTUBE を挿入する"
],
"WorkPoints": [
"②はﾘﾆｱﾚｰﾙと平行に取付ける事",
"9... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立④",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑤",
"Words": [],
"WorkItems": [
"1. ①へCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安全作業"
],
"ToolPart... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑤",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑥",
"Words": [],
"WorkItems": [
"1. ①へ②を挿入し､BEARING-UNIT をBOLT で仮取付けする",
"2. ㉖を取り外す"
],
"WorkPoints": [
"BEARING-UNIT の止めﾈｼﾞ(2箇所)がﾎﾞｰﾙﾈｼﾞ挿入穴に出てい無い事",
"止めﾈｼﾞ",
"SD-A041321-022にて本締... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑥",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4835",
"ToolName": "ﾘﾌﾄ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑦",
"Words": [],
"WorkItems": [
"1. ①へCOLLAR LOCK-NUT を取付ける",
"2. 仮締めﾎﾞﾙﾄ(4-M4)を本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
"InspectionNos":... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑦",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑧",
"Words": [],
"WorkItems": [
"2. 1の完成品へBOLT WASHER を仮取付けする",
"1. ①へ②をSPACER BOLT で取付ける"
],
"WorkPoints": [
"ﾘﾆｱﾌﾞﾛｯｸとS-pinに隙間無い事",
"SD-A041321-022にて本締め"
],
"Tolks": [
"締... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑧",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑨",
"Words": [
"2-M6×20締付ﾄﾙｸ 9.8N･m",
"4-M5×20締付ﾄﾙｸ 6.0N･m",
"4-M4×16締付ﾄﾙｸ 3.2N･m",
"押し上げ"
],
"WorkItems": [
"2. 回転ﾄﾙｸ確認",
"1. ①のﾌﾟﾚｰﾄを上部ﾒｶｴﾝﾄﾞまで移動し､本締めする"
],
"WorkPoints... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑨",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑩",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"2. 1の完成品へCABLE を接続し整線する",
"1. ①へ②SENSOR をBOLT WASHER BOLT WASHER WASHER で取付ける"
],
"WorkPoint... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑩",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑪",
"Words": [],
"WorkItems": [
"1. ①へPULLEY をBOLT で取付ける",
"2. 1の完成品へSCREW WASHER を取付ける"
],
"WorkPoints": [
"PULLEY はﾎﾞｰﾙﾈｼﾞへ押し付ける事",
"隙間を均等にする事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑪",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑫",
"Words": [
"2㎜",
"3㎜"
],
"WorkItems": [
"1. COVER へLABEL を貼付ける",
"2. ②へ1の完成品をBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 150cN･... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑫",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑬",
"Words": [],
"WorkItems": [
"1. ①へCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"干渉無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"W... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑬",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑭",
"Words": [
"ｲﾝｼｭﾛｯｸ150mm",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"◆2. グリスチューブを接続し、㉛を注入する",
"1. ①へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑭",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑮",
"Words": [],
"WorkItems": [
"1. ①へBRACKET をBOLT WASHER で取付ける",
"2. 1の完成品へSPACER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"In... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑮",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑯",
"Words": [],
"WorkItems": [
"1. ①へ②をBOLT で取付ける",
"2. 1の完成品へT-BELT をｾｯﾄし､④をBOLT WASHER で取付ける"
],
"WorkPoints": [
"質量(M):2.5g/m幅 (W):15mmｽﾊﾟﾝ(S):88mm",
"74.0N･m±10%"
],
"Tolk... | [
{
"WorkName": "ﾒｲﾝﾌﾚｰﾑ組立⑯",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ｻﾌﾞﾌﾚｰﾑ組立",
"Words": [],
"WorkItems": [
"3. ㉗を取り外す",
"1. ㉗へFRAME FRAME を取付ける",
"2. 1の完成品へPLATE をBOLT で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"FRAME FRAME を定盤及びDピンに押し付け㉗の取付けネジを締結する事"... | [
{
"WorkName": "ｻﾌﾞﾌﾚｰﾑ組立",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5050",
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞｻﾌﾞﾌﾚｰﾑ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "引き出部受けﾌﾞﾗｹｯﾄ(左)組立",
"Words": [
"この作業では同じものを2個製作",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"黄色ﾏｰｸ方向"
],
"WorkItems": [
"◆1. PIN の最も中心に寄っている位置にマーキングし、㉖を塗布する",
"2. BRACKET へ1の完成品をWASHER NUT で取付ける",
"3. 2の完成品へBRA... | [
{
"WorkName": "引き出部受けﾌﾞﾗｹｯﾄ(左)組立",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "引き出部受けﾌﾞﾗｹｯﾄ(右)組立",
"Words": [
"黄色ﾏｰｸ方向",
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆1. PIN の最も中心に寄っている位置にマーキングし、PIN PIN に㉖を塗布する",
"2. BRACKET へ1の完成品をWASHER NUT WASHER WASHER で取付ける",
"3. 2の完成品へBRAC... | [
{
"WorkName": "引き出部受けﾌﾞﾗｹｯﾄ(右)組立",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "ｸﾞﾘｰｽ飛散防止ｶﾊﾞｰ組立",
"Words": [],
"WorkItems": [
"1. COVER にBRACKET をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"SD-A041086-503にて本締め"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "ｸﾞﾘｰｽ飛散防止ｶﾊﾞｰ組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "補強ﾌﾞﾗｹｯﾄ組立①",
"Words": [],
"WorkItems": [
"1. BRACKET にBRACKET をWASHER BOLT で仮取付けする"
],
"WorkPoints": [
"SD-A041086-516にて本締め"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "補強ﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GH ：ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ(ﾘﾌﾄ部 ﾏｶﾞｼﾞﾝ側)) NPM-G Serirs (001-035）",
"WorkName": "補強ﾌﾞﾗｹｯﾄ組立②",
"Words": [],
"WorkItems": [
"1. PLATE へPOST をSCREW で仮取付けする"
],
"WorkPoints": [
"SD-A041086-516にて本締め"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes":... | [
{
"WorkName": "補強ﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立1",
"Words": [],
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付ける",
"2. 1完成品にSENSOR SENSOR をSCREW BOLT WASHER で取付ける"
],
"WorkPoints": [
"面を合わせて取付ける",
"投光側:ｺﾈｸﾀ名称_B1304TR",
"投光側... | [
{
"WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立2",
"Words": [],
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付ける",
"2. 1完成品に③をSCREW WASHER WASHER で取付ける"
],
"WorkPoints": [
"面を合わせて取付ける",
"受光側:ｺﾈｸﾀ名称_B1304R",
"ｾﾝｻｰ付属品"
],
... | [
{
"WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "水準器組立",
"Words": [
"削除"
],
"WorkItems": [
"1. BLOCK にPRECISION-LEVEL をSCREW で取付ける",
"2. 1完成品をBRACKET にBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"BLOCK とPRECISION-LEVEL の両端揃え",
"同一の物を2個作製",
... | [
{
"WorkName": "水準器組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "開閉ｱｰﾑ組立",
"Words": [],
"WorkItems": [
"1. LEVER にBOLT NUT ･BOLT を取付ける"
],
"WorkPoints": [
"11㎜",
"取付け寸法:11㎜",
"BOLT はﾎﾞﾙﾄ先端が穴から出ない様挿入する",
"各2個づつ作製する"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],... | [
{
"WorkName": "開閉ｱｰﾑ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立1",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1"
],
"WorkItems": [
"1. CYLINDER CYLINDER CYLINDER CYLINDER にBRACKET をBOLT WASHER で取付ける",
"◆2. COLLAR にｸﾞﾘ-ｽを塗布し､1の完成品にCOLLAR BRACKET をNUT で取付ける"
],
"WorkPo... | [
{
"WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立2",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"▲1. COLLAR にｸﾞﾘｰｽを塗布する",
"◆2. ②③に④⑤をCOLLAR BOLT で取付ける"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置",
"ﾚﾊﾞｰとﾌﾞﾗｹｯﾄの間に... | [
{
"WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立1",
"Words": [],
"WorkItems": [
"2. 1完成品にSPACER をBOLT WASHER で取付ける",
"1. BRACKET にLABEL を貼付ける",
"3. 2完成品にSPACER をBOLT NUT で取付ける"
],
"WorkPoints": [
"24㎜",
"2㎜",
"5㎜",
"3... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立1",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立2",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆1. COLLAR にｸﾞﾘ-ｽを塗布する",
"◆2. ①に②③をCOLLAR COLLAR BOLT で取付ける"
],
"WorkPoints": [
"ｸﾞﾘ-ｽ塗布位置",
"接触面にｸﾞﾘ-ｽ塗... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立3",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆2. 1完成品にSTOPPER をBOLT で取付ける",
"1. ①にSPACER BEARING をBOLT で取付ける"
],
"WorkPoints": [
"ﾚﾊﾞｰとの接触部分にｸﾞﾘｰｽ塗布",
"ｽﾄｯﾊﾟｰにﾚﾊﾞｰを当付け､ｽﾄｯ... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立4",
"Words": [],
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT WASHER で取付ける",
"2. 1完成品に④をBOLT WASHER で取付け後､CABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"B1304TR"
],
"Tolks": [
"締付ﾄﾙｸ 194... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立4",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立5",
"Words": [],
"WorkItems": [
"1. ①に②③を取付け検出動作を確認する"
],
"WorkPoints": [
"上側:B1320R",
"上側:B1322R",
"下側:B1321R",
"下側:B1323R",
"取付け寸法:22㎜",
"取付け寸法:9㎜",
"取付け寸法:22㎜",
... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立5",
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolName": "PHﾁｪｯｶｰ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WEMA-G002-C11",
"Others": "-",
"ProcessNames": [
"作... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立6",
"Words": [
"接着剤塗布 米粒:各1",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①の配線を固定する",
"◆2. 1完成品にSPRING を取付ける"
],
"WorkPoints": [
"ﾊﾞﾈとﾎﾞﾙﾄの... | [
{
"WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立6",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立1",
"Words": [],
"WorkItems": [
"1. BRACKET にLABEL を貼付ける",
"2. 1完成品ににSPACER をBOLT WASHER で取付ける",
"3. 2完成品にSPACER をBOLT NUT で取付ける"
],
"WorkPoints": [
"24㎜",
"18㎜",
"5㎜",
"... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立1",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立2",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆1. COLLAR にｸﾞﾘ-ｽを塗布する",
"◆2. ①に②③をCOLLAR COLLAR BOLT で取付ける"
],
"WorkPoints": [
"ｸﾞﾘ-ｽ塗布位置",
"接触面にｸﾞﾘ-ｽ塗布... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立3",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆2. 1完成品にSTOPPER をBOLT で取付ける",
"1. ①にSPACER BEARING をBOLT で取付ける"
],
"WorkPoints": [
"ﾚﾊﾞｰとの接触部分にｸﾞﾘｰｽ塗布",
"ｽﾄｯﾊﾟｰにﾚﾊﾞｰを当付け､ｽﾄｯﾊ... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立4",
"Words": [],
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT WASHER で取付ける",
"2. 1完成品に④をBOLT WASHER で取付け後､CABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"B1344TR"
],
"Tolks": [
"締付ﾄﾙｸ 194c... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立4",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立5",
"Words": [
"ｸﾞﾘｰｽ塗布 豆粒:各1"
],
"WorkItems": [
"◆1. ①にSPRING を取付ける"
],
"WorkPoints": [
"ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": ... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立5",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立6",
"Words": [],
"WorkItems": [
"1. ①に②③を取付け検出動作を確認する"
],
"WorkPoints": [
"下側:B1341T",
"上側:B1340T",
"上側:B1340",
"下側:B1341",
"取付け寸法:19㎜",
"取付け寸法:19㎜",
"B1341･B1341Tｾﾝ... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立6",
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolName": "PHﾁｪｯｶｰ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WEMA-G002-C11",
"Others": "-",
"ProcessNames": [
"作業... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立7",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸにより､ﾗﾍﾞﾙを配線に固定する",
"･ｲﾝｼｭﾛｯｸによる固定方法"
],
"WorkItems": [
"1. ①にCABLE を引き回し配線を固定する",
"■2. 1完成品のｾﾝｻｰﾗﾍﾞﾙ... | [
{
"WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立7",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D06",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "ｼｬｯﾀｰ部前組み",
"Words": [],
"WorkItems": [
"1. LEVER にSPACER をBOLT NUT で取付ける",
"2. 1完成品をBRACKET BRACKET にBEARING BOLT WASHER で取付ける",
"3. 2完成品にSTOPPER をBOLT で取付ける"
],
"WorkPoints": [
"BOLT はﾎﾞﾙﾄ先端が穴から出ないよ... | [
{
"WorkName": "ｼｬｯﾀｰ部前組み",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／ﾊﾟﾚｯﾄｽﾄｯｸ部(001-039)",
"WorkName": "銘板貼付け1",
"Words": [],
"WorkItems": [
"1. GUIDE にLABEL を､GUIDE にLABEL を貼付ける"
],
"WorkPoints": [
"反対面も同様に貼付けの事",
"1㎜",
"1㎜",
"1㎜",
"2㎜"
],
"Tolks": [],
"InspectionItems": [],
"Insp... | [
{
"WorkName": "銘板貼付け1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.