input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾁｪｯｶｰの接続と立ち上げ",
"Words": [],
"WorkItems": [
"1. ﾄﾚｲ本体とﾁｪｯｶｰの接続",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝの立ち上げ",
"3. PC画面が立ち上がったらNPM-WXのｱｲｺﾝをﾀﾞﾌﾞﾙｸﾘｯｸ",
"4. ﾁｪｯｶｰの電源BOXのSWをON",
"5. ｼｽﾃﾑ立ち上げ"
],
"WorkPoints": [
"･ﾁｪｯｶｰ電... | [
{
"WorkName": "ﾁｪｯｶｰの接続と立ち上げ",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TP軸原点登録-1",
"Words": [
"148.5㎜",
"1㎜",
"ﾒｶｽﾄｯﾊﾟｰ",
"ﾌﾞﾗｹｯﾄ端面",
"②",
"③",
"⑤",
"①",
"④",
"⑥"
],
"WorkItems": [
"1. TP軸のﾊﾟﾜｰON",
"2. TP軸仮原点登録",
"3. ﾀｲﾐﾝｸﾞﾌﾟｰﾘの固定確認... | [
{
"WorkName": "TP軸原点登録-1",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TP軸原点登録-2",
"Words": [
"148.5㎜",
"ﾒｶｽﾄｯﾊﾟｰ",
"ﾌﾞﾗｹｯﾄ端面",
"①",
"②"
],
"WorkItems": [
"1. TP軸原点復帰を行う",
"2. ﾒｶｽﾄよりﾌﾞﾗｹｯﾄ端面148.5mm位置を確認"
],
"WorkPoints": [
"･ｾﾝｻｰ光軸より1㎜位置･ﾒｶｽﾄよりﾌﾞﾗｹｯﾄ端... | [
{
"WorkName": "TP軸原点登録-2",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-1",
"Words": [
"②",
"③",
"④",
"⑤",
"⑥",
"⑦",
"⑩",
"①",
"⑧",
"⑨"
],
"WorkItems": [
"1. ﾊﾟﾜｰONを行う",
"2. TL軸原点復帰を行う",
"3. 引き出部を原点位置から下段23ｽﾛｯﾄ高さへ... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-1",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-2",
"Words": [
"A 2",
"A-A断面",
"測定位置(上面から見た図)",
"下23段目",
"引き出部",
"A1A2",
"A",
"A",
"引き出部搬送面",
"下23段目",
"治具ﾊﾟﾚｯﾄ",
"治具ﾊﾟﾚｯﾄ",
"※1",
"+",
"... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-2",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-3",
"Words": [
"締める",
"緩める",
"③",
"FM-5946",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5946",
"ﾊﾟﾚｯﾄｽﾄｯｸ部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
],
"WorkIt... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-3",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-1(ｵﾌｾｯﾄ値入力-1)",
"Words": [
"①",
"②",
"⑤",
"⑥",
"⑦",
"⑧",
"⑨",
"④",
"③"
],
"WorkItems": [
"1. TL軸の原点復帰を行う",
"2. 原点復帰完了を押す",
"3. ｵﾌｾｯﾄ値の確認",
"4. 連結位... | [
{
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-1(ｵﾌｾｯﾄ値入力-1)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-2(ｵﾌｾｯﾄ値入力-2)",
"Words": [
"①",
"③",
"④",
"⑤",
"⑥",
"②"
],
"WorkItems": [
"1. 入力を確認したら TLｵﾌｾｯﾄ書込みを押す",
"2. 入力がされているか確認",
"3. 数値が出ればOK",
"4. 原点復帰を行う",
"5. 原点... | [
{
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-2(ｵﾌｾｯﾄ値入力-2)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-3(-側ORｾﾝｻｰ調整)",
"Words": [
"①",
"-1.5㎜",
"②"
],
"WorkItems": [
"1. ﾏｲﾅｽﾘﾐｯﾄｾﾝｻｰ側のﾄﾞｸﾞ位置の確認",
"2. TL軸ﾏﾆｭｱﾙ動作で-1.5mm入力する",
"3. TL軸ﾏﾆｭｱﾙ動作で-0.1㎜追加し-1.6㎜迄下げる"
],
"WorkPoints": [
... | [
{
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-3(-側ORｾﾝｻｰ調整)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-4(ｵﾌｾｯﾄ値0戻し-1)",
"Words": [
"①",
"②",
"③",
"④",
"⑤",
"⑥",
"⑦",
"⑨",
"⑧"
],
"WorkItems": [
"1. TL軸の原点復帰を行う",
"2. 原点復帰完了を押す",
"3. 連結位置へTL軸を上げる",
"4.... | [
{
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-4(ｵﾌｾｯﾄ値0戻し-1)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-5(ｵﾌｾｯﾄ値0戻し-2)",
"Words": [
"①",
"②",
"③",
"④",
"⑤"
],
"WorkItems": [
"1. ｵﾌｾｯﾄ値の確認",
"4. 原点復帰後ｵﾌｾｯﾄ値の確認",
"2. TL軸の原点復帰を行う",
"3. 原点復帰完了を押す",
"5. TL軸のｵﾌｾｯﾄ値が\"0\"... | [
{
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄの調整-5(ｵﾌｾｯﾄ値0戻し-2)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞの実施",
"Words": [
"①",
"②",
"高速になっている事を確認"
],
"WorkItems": [
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認する",
"2. ｴｰｼﾞﾝｸﾞの実施"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ﾁｪｯｶｰ画面で90... | [
{
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞの実施",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "各ﾍﾞﾙﾄﾃﾝｼｮﾝの確認-1",
"Words": [],
"WorkItems": [
"1. ①のTL軸のﾍﾞﾙﾄ張力を調整",
"2. TP軸のﾍﾞﾙﾄ張力を調整"
],
"WorkPoints": [
"測定箇所",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ規格値:74N±10%質量(M):2.5g/mm幅 (W):15mmｽﾊﾟﾝ(S):88mm",
"ﾍﾞﾙﾄの測定箇所付近を弾いて測定する",
... | [
{
"WorkName": "各ﾍﾞﾙﾄﾃﾝｼｮﾝの確認-1",
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolName": "ﾍﾞﾙﾄ張力計",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "74N･m±10%",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WEAV-G002-C36",
"Others": "TL軸",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "各ﾍﾞﾙﾄﾃﾝｼｮﾝの確認-2",
"Words": [],
"WorkItems": [
"1. TP軸のﾓｰﾀｰ側ﾍﾞﾙﾄ張力を調整",
"2. ﾀｲﾐﾝｸﾞﾌﾟｰﾘｰとﾀｲﾐﾝｸﾞﾍﾞﾙﾄとの合わせﾏｰｸを付ける"
],
"WorkPoints": [
"ﾍﾞﾙﾄﾃﾝｼｮﾝ規格値:44N±10%質量(M):2.5g/mm幅 (W):9mmｽﾊﾟﾝ(S):68mm",
"ﾍﾞﾙﾄの測定箇所付近を弾... | [
{
"WorkName": "各ﾍﾞﾙﾄﾃﾝｼｮﾝの確認-2",
"QualityItem": "張力確認",
"ToolManageNo": "-",
"ToolName": "ﾍﾞﾙﾄ張力計",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "44N･m±10%",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WEAV-G002-C36",
"Others": "TP軸",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-4",
"Words": [
"②",
"③",
"④",
"⑧",
"⑩",
"⑦",
"①",
"⑤",
"⑥",
"⑨",
"⑪",
"⑫",
"⑬"
],
"WorkItems": [
"1. ﾊﾟﾜｰONを行う",
"2. ｵﾌｾｯﾄ値の確認",
... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-4",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-5",
"Words": [
"A 2",
"A 0",
"A 1",
"A-A断面",
"測定位置(上面から見た図)",
"下23段目",
"引き出部",
"A1A0A2",
"A",
"A",
"引き出部搬送面",
"下23段目",
"治具ﾊﾟﾚｯﾄ",
"治具ﾊﾟﾚｯﾄ",
... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-5",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-6",
"Words": [
"締める",
"①",
"緩める",
"③",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5946",
"治具ﾊﾟﾚｯﾄ",
"FM-5946",
"ﾊﾟﾚｯﾄｽﾄｯｸ部",
"引き出部",
"A1A0A2",
"②",
"③",
... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-6",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-7",
"Words": [
"①",
"引き出部搬送面",
"ﾊﾟﾚｯﾄｽﾄｯｸ部",
"FM-5946",
"治具ﾊﾟﾚｯﾄ",
"FM-5946",
"ﾊﾟﾚｯﾄｽﾄｯｸ部",
"引き出部",
"A1A0A2",
"②",
"③",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]... | [
{
"WorkName": "TL軸とﾊﾟﾚｯﾄｽﾄｯｸ部の高さ調整-7",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TL軸原点登録とﾏｲﾅｽ側ｾﾝｻｰの確認",
"Words": [
"①",
"-1.5㎜",
"②"
],
"WorkItems": [
"3. 再度原点復帰し､-M/S位置Bを確認｡また､-O/R PH位置Cを確認",
"■4. 各段の高さを再確認しｶｯﾌﾟﾘﾝｸﾞを締め付ける",
"1. 原点復帰後､TL軸ﾏﾆｭｱﾙ動作で-1.5mm入力する",
"2. TL軸ﾏﾆｭｱﾙ動... | [
{
"WorkName": "TL軸原点登録とﾏｲﾅｽ側ｾﾝｻｰの確認",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-1(TP軸ﾚﾊﾞｰ位置確認)",
"Words": [
"①",
"②",
"③",
"④",
"2.ﾄﾚｲ本体のの原点復帰",
"⑤",
"⑥",
"⑪",
"⑫",
"⑦",
"⑧",
"⑨",
"⑩"
],
"WorkItems": [
"1. TP軸のﾊﾟﾜｰON",
... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-1(TP軸ﾚﾊﾞｰ位置確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-2(TP軸ﾚﾊﾞｰ位置確認)",
"Words": [],
"WorkItems": [
"2. ｶﾞｲﾄﾞ平行出し治具とﾍﾞｱﾘﾝｸﾞの隙間を調整",
"1. ｶﾞｲﾄﾞ平行出し治具を引き出部に取付"
],
"WorkPoints": [
"接触",
"基準となるLMｶﾞｲﾄﾞとの隙間が無い事をｼｯｸﾈｽｹﾞｰｼﾞで確認",
"治具とﾍﾞｱﾘﾝｸﾞの隙間を0.2㎜の... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-2(TP軸ﾚﾊﾞｰ位置確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-3(TP軸ﾚﾊﾞｰ位置確認)",
"Words": [],
"WorkItems": [
"1. ﾚﾊﾞｰ位置の調整"
],
"WorkPoints": [
"ｽﾄﾛｰｸ調整治具",
"ｶｯﾌﾟﾘﾝｸﾞを緩める｡ｵｰﾊﾞｰﾗﾝまで行か無い事",
"治具の設置",
"ｽﾄﾛｰｸ調整治具を入れ微調整する",
"①左右同時前後調整",
"②左右片側毎の調... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-3(TP軸ﾚﾊﾞｰ位置確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-4(TP軸ﾚﾊﾞｰ位置確認)",
"Words": [
"G",
"H",
"①"
],
"WorkItems": [
"1.吸着位置でﾚﾊﾞｰの確認を行う",
"2. ﾊﾟﾜｰをOFF",
"■3. TP軸のｶｯﾌﾟﾘﾝｸﾞの増し締め"
],
"WorkPoints": [
"･ﾍﾞｱﾘﾝｸﾞに接触させ片側の隙間を測定",
"固定... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-4(TP軸ﾚﾊﾞｰ位置確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-5(ﾊﾟﾚｯﾄ検出ｾﾝｻｰの確認調整)",
"Words": [],
"WorkItems": [
"2. 引き出部を連結位置へ移動",
"4. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ戻しへ移動",
"3. 引き出部をNG排出部へ移動",
"1. ﾄﾚｲ本体のの原点復帰",
"5. ﾊﾟﾚｯﾄ検出ｾﾝｻｰの光軸の確認"
],
"WorkPoints": [
"投光側ｾﾝ... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-5(ﾊﾟﾚｯﾄ検出ｾﾝｻｰの確認調整)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-6(ﾊﾟﾚｯﾄ検出ｾﾝｻｰの確認調整)",
"Words": [
"⑥",
"②",
"①",
"③",
"④",
"⑤"
],
"WorkItems": [
"1. ﾊﾟﾚｯﾄ検出ｾﾝｻｰの光軸の調整",
"2. TP軸原点復帰",
"3. ﾊﾟﾚｯﾄ戻し"
],
"WorkPoints": [
"1,投光側ｾ... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-6(ﾊﾟﾚｯﾄ検出ｾﾝｻｰの確認調整)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-7(TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ-調整)",
"Words": [
"①",
"- +",
"下記動作で､ｾﾝｻｰの状態を確認する｡148.5stの位置を基準に ･+0.23stで投光 ･+0.40stで遮光(+0.24~+0.39st間は どちらでも可) (吸着側への移動)",
"②"
],
"WorkItems": [
"... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-7(TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ-調整)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-8(TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ-調整)",
"Words": [
"≪付録≫",
"①",
"+",
"-",
"②",
"③",
"④",
"⑤",
"⑥"
],
"WorkItems": [
"1. ﾏﾆｭﾋﾟﾚｰﾀｰを押し+0.40st -148.14㎜位置へ移動",
"2. ｾﾝｻｰ位置調整後ｾﾝｻｰの固定... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-8(TL軸ｲﾝﾀｰﾛｯｸｾﾝｻ-調整)",
"QualityItem": "原点確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames":... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-9(ﾏｲﾅｽ側ﾒｶｽﾄｯﾊﾟｰの確認調整)",
"Words": [
"①",
"②",
"⑤",
"③",
"④",
"ｽﾄｯﾊﾟｰ",
"調整ﾎﾞﾙﾄ",
"ﾛｯｸﾅｯﾄ"
],
"WorkItems": [
"2. 隙間確認後PT軸の原点復帰を行う",
"3. 引き出部ｱｰﾑをﾊﾟﾚｯﾄ引き出部へ移動する",
... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-9(ﾏｲﾅｽ側ﾒｶｽﾄｯﾊﾟｰの確認調整)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-10(ﾄﾞｸ・ｾﾝｻｰの位置確認)",
"Words": [
"原点ｾﾝｻ",
"③",
"④",
"②",
"⑥",
"①",
"⑤",
"⑦",
"⑧",
"⑩",
"⑪"
],
"WorkItems": [
"1. PT軸の原点復帰を行う",
"2. ﾘﾌﾄ上昇で吸着位置へ",
... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-10(ﾄﾞｸ・ｾﾝｻｰの位置確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-11(吸着位置でのO/Rｾﾝｻｰの投光・遮光の確認)",
"Words": [
"②",
"①",
"③",
"④",
"⑤",
"⑥",
"⑦",
"⑧"
],
"WorkItems": [
"2. TP軸ﾏﾆｭｱﾙ動作で83.2㎜の位置まで移動",
"3. TP軸ﾏﾆｭｱﾙ動作で83.4㎜の位置まで移動",
"... | [
{
"WorkName": "引き出軸のｽﾄﾛｰｸ調整-11(吸着位置でのO/Rｾﾝｻｰの投光・遮光の確認)",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"Process... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻｰの調整",
"Words": [
"補給段",
"上23段目",
"下23段目"
],
"WorkItems": [
"2. 製品ﾊﾟﾚｯﾄにてｾﾝｻの確認をする",
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻｰの位置調整"
],
"WorkPoints": [
"17㎜時LED(緑)→点灯LED(赤)→点灯",
"16㎜時LED(緑)→点灯L... | [
{
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻｰの調整",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻｰ確認",
"Words": [
"①",
"②",
"③",
"④",
"⑤",
"⑥"
],
"WorkItems": [
"4. 補給位置へ一段下げる",
"2. TL軸･TP軸の原点復帰を行う",
"3. 原点復帰確認後ﾘﾌﾄ吸着位置へﾘﾌﾄｱｯﾌﾟ",
"5. ﾊﾟﾚｯﾄ有り･無しで検出ｾﾝｻｰがON･OFFするかを... | [
{
"WorkName": "ﾊﾟﾚｯﾄ有無検出ｾﾝｻｰ確認",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "TTL軸のｽﾄﾛｰｸ調整と異音確認",
"Words": [
"①",
"②",
"①",
"②",
"④",
"③",
"①",
"②",
"⑤",
"高速になっている事を確認",
"連結ﾌﾞﾛｯｸ",
"連結ﾌﾞﾛｯｸ"
],
"WorkItems": [
"4. TTL軸異音確認の為TL軸のｽﾋﾟｰﾄﾞを高速へ変更... | [
{
"WorkName": "TTL軸のｽﾄﾛｰｸ調整と異音確認",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "引き出軸ﾊﾟﾚｯﾄ有り無しｾﾝｻｰ確認",
"Words": [
"①",
"②",
"③",
"④",
"⑦",
"⑧",
"⑥",
"⑤",
"⑨"
],
"WorkItems": [
"2. TL軸･TP軸の原点復帰を行う",
"3. 原点復帰確認後ﾘﾌﾄ連結位置へ移動する",
"4. ﾊﾟﾚｯﾄ戻しを押して引き出部ｱｰﾑを... | [
{
"WorkName": "引き出軸ﾊﾟﾚｯﾄ有り無しｾﾝｻｰ確認",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄの取付-1【ｽﾄｯｶｰ側】",
"Words": [],
"WorkItems": [
"1. ①にSHAFT をBOLT WASHER で仮取付け"
],
"WorkPoints": [
"Dｶｯﾄ面",
"SHAFT を上から挿入",
"ｼｬﾌﾄ取付ﾎﾞﾙﾄ",
"左側下",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
... | [
{
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄの取付-1【ｽﾄｯｶｰ側】",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄの取付-2【ｽﾄｯｶｰ側】",
"Words": [
"ｱｰﾑ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"WorkItems": [
"1. ｼｬｯﾀｰｼｬﾌﾄﾌﾟﾚｰﾄとｽﾄｯﾊﾟｰﾎﾞﾙﾄと調整",
"2. 隙間が無い事を確認しｼｬﾌﾄ取付ﾎﾞﾙﾄとｼｬﾌﾄ抜け防止ﾎﾞﾙﾄを増し締めする"
],
"WorkPoints": [
"※ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事... | [
{
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄの取付-2【ｽﾄｯｶｰ側】",
"QualityItem": "動作確認",
"ToolManageNo": "FM-6005",
"ToolName": "ﾄﾚｲﾕﾆｯﾄ専用配線検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄの取付-1【ｽﾄｯｶｰ側】",
"Words": [
"仮止め:SD-A042069-645にて本締め"
],
"WorkItems": [
"1. ①にSHAFT をBOLT WASHER で仮取付け"
],
"WorkPoints": [
"Dｶｯﾄ面",
"SHAFT を上から挿入",
"ｼｬﾌﾄ取付ﾎﾞﾙﾄ",
"左側下",
"ｼｬｯﾀｰ... | [
{
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄの取付-1【ｽﾄｯｶｰ側】",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄの取付-2【ｽﾄｯｶｰ側】",
"Words": [
"ｱｰﾑ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"WorkItems": [
"2. ｽﾄｯﾊﾟｰとの隙間が無い事を確認しｼｬﾌﾄ取付ﾎﾞﾙﾄとｼｬﾌﾄ抜け防止ﾎﾞﾙﾄを増し締めする",
"1. ｼｬｯﾀｰｼｬﾌﾄﾌﾟﾚｰﾄとｽﾄｯﾊﾟｰﾎﾞﾙﾄとの調整"
],
"WorkPoints": [
"※ｽﾄｯﾊﾟｰﾎﾞ... | [
{
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄの取付-2【ｽﾄｯｶｰ側】",
"QualityItem": "動作確認",
"ToolManageNo": "FM-6005",
"ToolName": "ﾄﾚｲﾕﾆｯﾄ専用配線検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ｼｬｯﾀｰｼｬﾌﾄ位置調整【ｽﾄｯｶｰ側】",
"Words": [],
"WorkItems": [
"1. ①のｼｬｯﾀｰ位置を調整する"
],
"WorkPoints": [
"治具は引き出部側のｼｬｯﾀｰに当付けの事",
"t0.02のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"NG排出部:t0.05",
"上23段目:t0.15",
"下23段目:t0.05",
"各... | [
{
"WorkName": "ｼｬｯﾀｰｼｬﾌﾄ位置調整【ｽﾄｯｶｰ側】",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻｰの調整【ｽﾄｯｶｰ側】",
"Words": [
"上23段目",
"下23段目",
"NG排出部",
"補給段",
"2mm",
"1mm"
],
"WorkItems": [
"1. ﾊﾟﾚｯﾄはみ出し検出PHｾﾝｻｰの位置調整",
"2. 製品ﾊﾟﾚｯﾄにてｾﾝｻの確認をする"
],
"WorkPoints": [
... | [
{
"WorkName": "ﾊﾟﾚｯﾄはみ出しｾﾝｻｰの調整【ｽﾄｯｶｰ側】",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整2(601-648)",
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"Words": [
"⑤",
"④",
"①",
"②",
"⑥",
"4ｻｲｸﾙ入力",
"高速になっている事を確認",
"③",
"補給位置､NGﾊﾟﾚｯﾄ位置及び全段数について､全段数確認する事｡",
"⑦"
],
"WorkItems": [
"2. ﾃﾞｰﾀｰ編集画面でTL軸･TP軸のｽﾋﾟｰﾄﾞを高... | [
{
"WorkName": "ﾊﾟﾚｯﾄ搬送ﾁｪｯｸ",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "上部ｶﾊﾞｰ取付",
"Words": [],
"WorkItems": [
"1. ①に②をSCREW SCREW で取付ける"
],
"WorkPoints": [
"SCREW の皿ﾋﾞｽで固定する為､おのずと位置が決まるのでSCREW を固定の際負荷を掛け無い事"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 350cN･m"
],
"Ins... | [
{
"WorkName": "上部ｶﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "P622ﾌﾞﾗｹｯﾄ取付",
"Words": [
"37.5㎜",
"19㎜"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"Work... | [
{
"WorkName": "P622ﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｼｭｰﾄ取付",
"Words": [],
"WorkItems": [
"1. ①に②を取付ける",
"2. 1完成品に③をBOLT WASHER で取付ける",
"3. 2完成品にCOVER をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 320cN･m",
"締付ﾄﾙｸ ... | [
{
"WorkName": "ｼｭｰﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "320cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "引き出部搬送ｶﾊﾞｰ取付-1",
"Words": [
"端面合わせ",
"端面合わせ"
],
"WorkItems": [
"1. ①にCOVER COVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"COVER COVER 取付時ﾊﾞｶ穴分外向きに取付け",
"前側端面に面合わせで取付ける事",
"吸着部取付けﾌﾟﾚｰﾄとの隙間を確認"... | [
{
"WorkName": "引き出部搬送ｶﾊﾞｰ取付-1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "引き出部搬送ｶﾊﾞｰ取付-2",
"Words": [],
"WorkItems": [
"1. ①にCOVER COVER をWASHER BOLT で取付ける"
],
"WorkPoints": [
"COVER とCOVER の切り欠き部を確認し取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionItems": [],
"Inspe... | [
{
"WorkName": "引き出部搬送ｶﾊﾞｰ取付-2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ﾘﾌﾄ部吸着側搬送ｶﾊﾞｰ取付-1",
"Words": [],
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"引き出部ｱｰﾑとの隙間を確認し干渉が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "ﾘﾌﾄ部吸着側搬送ｶﾊﾞｰ取付-1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ﾘﾌﾄ部吸着側搬送ｶﾊﾞｰ取付-2",
"Words": [
"45㎜",
"41.5㎜"
],
"WorkItems": [
"1. ①にCOVER をWASHER BOLT で取付ける"
],
"WorkPoints": [
"COVER の取付方向は短い方をﾌﾟﾚｰﾄ側へ",
"この部分にﾈｼﾞ穴分隙間を確保する事"
],
"Tolks": [
"締付ﾄﾙｸ ... | [
{
"WorkName": "ﾘﾌﾄ部吸着側搬送ｶﾊﾞｰ取付-2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "連結部(ﾄﾚｲ側)取付-1",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsMod... | [
{
"WorkName": "連結部(ﾄﾚｲ側)取付-1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-1(左前)",
"Words": [
"隙間確認項目",
"連結用ｹｰﾌﾞﾙの取り出し口",
"31㎜"
],
"WorkItems": [
"1. ①に②をSCREW SCREW で取付ける"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ･ｴｱｰ配管のかみ込みが無いよう注意する事",
"隙間無い事"
],
"Tolks": [
"締付... | [
{
"WorkName": "ｶﾊﾞｰ取付-1(左前)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-2(右前)",
"Words": [
"隙間確認項目",
"31㎜"
],
"WorkItems": [
"1. ①に②をSCREW で取付ける"
],
"WorkPoints": [
"隙間無い事"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"InspectionItems": [],
"InspectionNos":... | [
{
"WorkName": "ｶﾊﾞｰ取付-2(右前)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "連結部(ﾄﾚｲ側)取付-2",
"Words": [],
"WorkItems": [
"2. 1完成品にBRACKET をBOLT WASHER で取付ける",
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"取付は下図参照､矢印方向へﾊﾞｶ穴分押し当てて取付",
"取付は下図参照､矢印方向へﾊﾞｶ穴分押し当てて取付"
],
"T... | [
{
"WorkName": "連結部(ﾄﾚｲ側)取付-2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-3(上前)",
"Words": [
"隙間確認項目"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"隙間均等",
"隙間均等",
"長穴ｾﾝﾀｰに合せる"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems":... | [
{
"WorkName": "ｶﾊﾞｰ取付-3(上前)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-4(左後)",
"Words": [
"隙間確認項目"
],
"WorkItems": [
"1. ①にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"この高さを合わせる事",
"隙間無い事",
"この高さを合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"Inspection... | [
{
"WorkName": "ｶﾊﾞｰ取付-4(左後)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-5(右後)",
"Words": [
"隙間確認項目"
],
"WorkItems": [
"1. ①に②をSCREW で取付ける"
],
"WorkPoints": [
"この高さを合わせる事",
"この高さを合わせる事",
"隙間無い事"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m"
],
"InspectionItems... | [
{
"WorkName": "ｶﾊﾞｰ取付-5(右後)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "連結部(ﾄﾚｲ側)取付-3",
"Words": [],
"WorkItems": [
"1. ①に②をWASHER BOLT で取付ける"
],
"WorkPoints": [
"※ｶﾊﾞｰは取付けた状態で②を取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "連結部(ﾄﾚｲ側)取付-3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "連結ｺﾈｸﾀｰ・ｴｱｰﾁｭｰﾌﾞの固定",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)"
],
"WorkItems": [
"1. ①の連結ﾌﾞﾗｹｯﾄにｴｱｰ配管とｺﾈｸﾀｰ2本を固定する",
... | [
{
"WorkName": "連結ｺﾈｸﾀｰ・ｴｱｰﾁｭｰﾌﾞの固定",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-6(制御BOX前)",
"Words": [],
"WorkItems": [
"1. ﾕﾆｯﾄ本体とｱｰｽﾏｯﾄを接続している ｱｰｽ線を取り外す",
"2. ①に②をSCREW SCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionItems": [],
"Inspection... | [
{
"WorkName": "ｶﾊﾞｰ取付-6(制御BOX前)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-7(ｼｬｯﾀｰ機構部)",
"Words": [
"隙間確認項目"
],
"WorkItems": [
"1. ①にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"矢印部分の隙間を均等に｡傾きが有ればｻｲﾄﾞのｶﾊﾞｰで修正する",
"SCREW を締める際に両ｻｲﾄﾞのｶﾊﾞｰとの高さを合わせて固定する"
],
"Tolks": [
... | [
{
"WorkName": "ｶﾊﾞｰ取付-7(ｼｬｯﾀｰ機構部)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-8(後面下)",
"Words": [
"ﾌﾚｰﾑに合わせた時､この部分に隙間が生じる",
"隙間確認"
],
"WorkItems": [
"1. ①にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"COVER は①のﾌﾚｰﾑに乗せた状態で両ｻｲﾄﾞ均等に合わせ固定する"
],
"Tolks": [
"締付ﾄﾙｸ 350cN･m... | [
{
"WorkName": "ｶﾊﾞｰ取付-8(後面下)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰ取付-9(吸着部保護ｶﾊﾞｰの取付)",
"Words": [],
"WorkItems": [
"1. ①にCOVER をSCREW BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 350cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "ｶﾊﾞｰ取付-9(吸着部保護ｶﾊﾞｰの取付)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNa... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ｶﾊﾞｰの美観ﾁｪｯｸと連結部(ﾄﾚｲ側)取付",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"50㎜"
],
"WorkItems": [
"1. ①のｶﾊﾞｰ美観ﾁｪｯｸを行う",
"2. 1完成品にKNOB を取付ける",
"3. 2完成品に3をBOLT でGUIDE をBOLT WASHER ... | [
{
"WorkName": "ｶﾊﾞｰの美観ﾁｪｯｸと連結部(ﾄﾚｲ側)取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-WX ： ﾄﾚｲﾌｨ-ﾀﾞ-（ｽﾄｯｶ-仕様）:X11／全体組立調整3(701-722)",
"WorkName": "ﾄﾚｲ水準器の調整",
"Words": [],
"WorkItems": [
"1. ①の水準を再調整"
],
"WorkPoints": [
"内臓水準器:\"0\"に調整",
"・TL軸を上段マガジン 11段目に移動・チェッカーのパワーオフ・㉗冶具を引き出部に載せる・㉗に㉘水準器を載せる・トレイの水準を調整",
"基準水準器:X･Y方向 0.05㎜以内"
],
"Tolks": [],... | [
{
"WorkName": "ﾄﾚｲ水準器の調整",
"QualityItem": "手順確認",
"ToolManageNo": "FM-5247",
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面前側正面)",
"Words": [
"A",
"B",
"C",
"D",
"Ⓐ",
"Ⓓ",
"凸部"
],
"WorkItems": [
"1. FRAME にBRACKET BRACKET NUT CAP をBOLT WASHER BOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図",
"黒線部分の端面を揃え仮固定"
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面前側正面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面前側正面)",
"Words": [
"A",
"B",
"C",
"D",
"凸部",
"Ⓐ",
"Ⓑ"
],
"WorkItems": [
"1. FRAME にBRACKET BRACKET NUT CAP をBOLT WASHER BOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図",
"黒線部分の端面を揃え仮固定"
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面前側正面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面中央)",
"Words": [
"A",
"B",
"C",
"D",
"凸部",
"Ⓐ",
"Ⓒ",
"Ⓑ",
"仮止め:SD-A042452-015にて本締め"
],
"WorkItems": [
"1. FRAME にBRACKET BRACKET BRACKET BRACKET NUT CAP WASHER をBOLT WASHER BOLT BOLT で仮止め"
]... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面中央)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面中央)",
"Words": [
"凸部",
"Ⓐ",
"Ⓒ",
"Ⓑ",
"A",
"B",
"C",
"D",
"仮止め:SD-A042452-015にて本締め"
],
"WorkItems": [
"1. FRAME にBRACKET BRACKET BRACKET BRACKET NUT CAP WASHER をBOLT WASHER BOLT BOLT で仮止め"
]... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面中央)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面後側背面)",
"Words": [
"A",
"B",
"C",
"D",
"凸部",
"Ⓐ",
"Ⓑ",
"Ⓓ",
"Ⓒ"
],
"WorkItems": [
"1. FRAME にFRAME BRACKET NUT CAP をBOLT WASHER BOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図",
"... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面後側背面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面後側背面)",
"Words": [
"Ⓑ",
"Ⓓ",
"Ⓒ",
"Ⓐ",
"A",
"B",
"C",
"D",
"凸部",
"仮止め:SD-A042452-015にて本締め"
],
"WorkItems": [
"1. FRAME にBRACKET BRACKET NUT CAP CABLE-SUPPORT をBOLT WASHER BOLT で仮止め"
],
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面後側背面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面前側上面)",
"Words": [],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面前側上面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面前側上面)",
"Words": [],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面前側上面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面後側上面)",
"Words": [
"Ⓓ",
"Ⓑ",
"凸部",
"Ⓐ",
"A",
"B",
"C",
"D",
"仮止め:SD-A042452-015にて本締め"
],
"WorkItems": [
"1. FRAME にBRACKET NUT CAP をBOLT で仮止め"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面後側上面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面後側上面)",
"Words": [
"凸部",
"Ⓐ",
"Ⓓ",
"A",
"B",
"C",
"D",
"Ⓒ",
"ｹｰﾌﾞﾙ\u000bｻﾎﾟｰﾄ"
],
"WorkItems": [
"1. FRAME にBRACKET NUT CAP CABLE-SUPPORT をBOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面後側上面)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(中央面①)",
"Words": [],
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
"ToolName": "ｽｹｰﾙ",
"Size":... | [
{
"WorkName": "ﾌﾚｰﾑ組立(中央面①)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(後側中央①)",
"Words": [
"Ⓒ",
"Ⓐ",
"Ⓓ",
"Ⓑ",
"凸部",
"A",
"C",
"B",
"D"
],
"WorkItems": [
"1. FRAME にNUT CAP BRACKET をBOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図",
"黒線部分の端面を揃え仮固定"
]... | [
{
"WorkName": "ﾌﾚｰﾑ組立(後側中央①)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(中央面②)",
"Words": [],
"WorkItems": [
"1. ①②③をBOLT で組立"
],
"WorkPoints": [
"端面を揃える ※下略図黒線部分",
"隙間を最小にする ※下略図青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],... | [
{
"WorkName": "ﾌﾚｰﾑ組立(中央面②)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(後側中央②)",
"Words": [],
"WorkItems": [
"1. ①②をBOLT で組立"
],
"WorkPoints": [
"端面を揃える ※下略図黒線部分",
"隙間を最小にする ※下略図青線部分",
"ﾅｯﾄの向きに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],... | [
{
"WorkName": "ﾌﾚｰﾑ組立(後側中央②)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(左面)",
"Words": [],
"WorkItems": [
"1. ①②③④⑤をBOLT で組立"
],
"WorkPoints": [
"端面を揃える ※下略図黒線部分",
"隙間を最小にする ※下略図青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],... | [
{
"WorkName": "ﾌﾚｰﾑ組立(左面)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "ﾌﾚｰﾑ組立(右面)",
"Words": [],
"WorkItems": [
"1. ①②③④⑤をBOLT で組立"
],
"WorkPoints": [
"端面を揃える ※下略図黒線部分",
"隙間を最小にする ※下略図青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],... | [
{
"WorkName": "ﾌﾚｰﾑ組立(右面)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "安全SW組立前準備",
"Words": [],
"WorkItems": [
"2. JOINT にCABLE を通し､SWITCH に端子を挿入",
"■3. SWITCH の刻印番号(青色文字)に合わせて各端子を取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙ№を検査表に記載する"
],
"WorkPoints": [
"SWITCH のｶﾊﾞｰを開けて実施",
"ｹｰﾌﾞﾙの噛み込み無き事",
"型式 D4NH-1D... | [
{
"WorkName": "安全SW組立前準備",
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEWD-F013-051",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "安全SWﾚﾊﾞｰ取付",
"Words": [
"ｼﾞｮｲﾝﾄを取付",
"ｼﾞｮｲﾝﾄのﾛｯｸを締付",
"ｽｲｯﾁのｶﾊﾞｰを取付"
],
"WorkItems": [
"2. ｶﾊﾞｰの取付",
"3. 純正ｱｰﾑをLEVER に交換",
"1. ①のｼﾞｮｲﾝﾄの締付"
],
"WorkPoints": [
"手で締め込む",
"心線の嚙み込みに注意",
"LEVER の折り曲げに注意して取... | [
{
"WorkName": "安全SWﾚﾊﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "安全SWﾌﾞﾗｹｯﾄ取付",
"Words": [],
"WorkItems": [
"1. ①にBRACKET をBOLT NUT WASHER WASHER にて取付",
"2. 1完成品にLABEL を貼付ける"
],
"WorkPoints": [
"①とBRACKET を平行に取付ける ※青線部分",
"平行に取付ける",
"㉚で脱脂後LABEL を貼付ける",
"BOLT の飛び出た部分にNUT WASHER を取付ける"... | [
{
"WorkName": "安全SWﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "安全SW取付",
"Words": [
"167mm±0.5mm"
],
"WorkItems": [
"1. ①に②をBOLT WASHER にて取付"
],
"WorkPoints": [
"指定寸法にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全... | [
{
"WorkName": "安全SW取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "安全SWｹｰﾌﾞﾙ引き回",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. 安全SWｹｰﾌﾞﾙを結束"
],
"WorkPoints": [
"必要部分のみ描いています"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "安全SWｹｰﾌﾞﾙ引き回",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "右側面ｶﾊﾞｰ(銘板貼付け)",
"Words": [
"115㎜",
"120㎜"
],
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"LABEL は①脱脂後､貼付ける事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"■安全作業"
]... | [
{
"WorkName": "右側面ｶﾊﾞｰ(銘板貼付け)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "右側面ｶﾊﾞｰ(非常停止SW取付)",
"Words": [
"2.残りの指で矢印のほうに引く",
"3.反時計方向に回転",
"1.指で押さえながら"
],
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"取付けﾘﾝｸﾞ",
"SW部",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"回り止め金具",
"内側から取付詳細図"
... | [
{
"WorkName": "右側面ｶﾊﾞｰ(非常停止SW取付)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5254",
"ToolName": "非常ｽｲｯﾁ締付けｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：カバー部前準備 (001-024）",
"WorkName": "右側面ｶﾊﾞｰ(ﾘｾｯﾄSW取付)",
"Words": [
"A",
"B",
"C",
"A",
"B",
"C"
],
"WorkItems": [
"1. ①に②を取付(2ヵ所)",
"2. 1完成品に⑥を取付"
],
"WorkPoints": [
"両側のﾂﾒを開いてｹｰﾌﾞﾙと分ける",
"1完成品",
"ｶﾊﾞｰ正面",
"ﾗﾍﾞﾙが右側",
... | [
{
"WorkName": "右側面ｶﾊﾞｰ(ﾘｾｯﾄSW取付)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"Words": [],
"WorkItems": [
"1. PLATE にPULL をSCREW にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(正面左ﾌﾚｰﾑ前組)",
"Words": [
"Ⓐ",
"Ⓓ",
"Ⓒ",
"Ⓑ",
"A",
"B",
"C",
"D",
"凸部"
],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図"
],
"Tolks": [],
"In... | [
{
"WorkName": "開閉ｶﾊﾞｰ(正面左ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(正面右ﾌﾚｰﾑ前組)",
"Words": [
"Ⓒ",
"Ⓑ",
"A",
"B",
"C",
"D",
"凸部",
"Ⓐ",
"Ⓓ"
],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図"
],
"Tolks": [],
"In... | [
{
"WorkName": "開閉ｶﾊﾞｰ(正面右ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(傾斜部左ﾌﾚｰﾑ前組)",
"Words": [
"Ⓐ",
"Ⓑ",
"Ⓒ",
"Ⓓ",
"A",
"B",
"C",
"D",
"凸部"
],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図"
],
"Tolks": [],
"I... | [
{
"WorkName": "開閉ｶﾊﾞｰ(傾斜部左ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(傾斜部右ﾌﾚｰﾑ前組)",
"Words": [
"Ⓐ",
"Ⓑ",
"Ⓒ",
"Ⓓ",
"A",
"B",
"C",
"D",
"凸部"
],
"WorkItems": [
"1. FRAME にNUT CAP を取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ 組合せ図"
],
"Tolks": [],
"I... | [
{
"WorkName": "開閉ｶﾊﾞｰ(傾斜部右ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(上部左ﾌﾚｰﾑ前組)",
"Words": [
"Ⓐ",
"Ⓒ",
"Ⓑ",
"A",
"B",
"C",
"D",
"凸部",
"上側",
"上側",
"Ⓓ"
],
"WorkItems": [
"1. FRAME にNUT CAP BRACKET をBOLT で取付"
],
"WorkPoints": [
"ﾅｯﾄとｷｬｯﾌﾟ... | [
{
"WorkName": "開閉ｶﾊﾞｰ(上部左ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(上部右ﾌﾚｰﾑ前組)",
"Words": [
"Ⓐ",
"Ⓑ",
"Ⓒ",
"Ⓓ",
"A",
"B",
"C",
"D",
"凸部",
"仮止め:SD-A042452-114にて本締め"
],
"WorkItems": [
"1. FRAME にNUT CAP BRACKET BRACKET をBOLT で仮止め"
],
"WorkPoints"... | [
{
"WorkName": "開閉ｶﾊﾞｰ(上部右ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(正面中央ﾌﾚｰﾑ前組)",
"Words": [
"Ⓑ",
"M5",
"M4",
"Ⓐ",
"M5",
"凸部",
"Ⓒ",
"C",
"B",
"A",
"D",
"仮止め:SD-A042452-112にて本締め"
],
"WorkItems": [
"1. FRAME にNUT NUT CAP BRACKET をBOLT で仮止め"
... | [
{
"WorkName": "開閉ｶﾊﾞｰ(正面中央ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(傾斜部下ﾌﾚｰﾑ前組)",
"Words": [
"仮止め:SD-A042452-113にて本締め"
],
"WorkItems": [
"1. FRAME にNUT CAP BRACKET BRACKET をBOLT WASHER BOLT で指定寸法にて仮止め"
],
"WorkPoints": [
"FRAME BRACKET の端面を揃える",
"FRAME BRACKET の端面を揃える ※青線部分"
... | [
{
"WorkName": "開閉ｶﾊﾞｰ(傾斜部下ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(傾斜部上ﾌﾚｰﾑ前組)",
"Words": [],
"WorkItems": [
"1. FRAME にNUT CAP BRACKET BRACKET をBOLT WASHER BOLT で指定寸法にて取付"
],
"WorkPoints": [
"FRAME BRACKET BRACKET の端面を揃える",
"FRAME BRACKET の端面を揃える ※青線部分"
],
"Tolks": [],
"Inspe... | [
{
"WorkName": "開閉ｶﾊﾞｰ(傾斜部上ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(上部後ﾌﾚｰﾑ前組)",
"Words": [
"M5",
"Ⓒ",
"M4",
"M5",
"M5",
"Ⓐ",
"Ⓑ",
"凸部",
"D",
"C",
"B",
"A",
"Ⓓ",
"仮止め:SD-A042452-114にて本締め"
],
"WorkItems": [
"1. FRAME にNUT NUT CAP を... | [
{
"WorkName": "開閉ｶﾊﾞｰ(上部後ﾌﾚｰﾑ前組)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電対策工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(正面ﾌﾚｰﾑ組立)",
"Words": [],
"WorkItems": [
"1. ①②③をBRACKET BOLT BOLT WASHER にて取付"
],
"WorkPoints": [
"接合面の隙間を最小に取付",
"接合面の端面を揃える",
"接合面の端面を揃える",
"接合面の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"Insp... | [
{
"WorkName": "開閉ｶﾊﾞｰ(正面ﾌﾚｰﾑ組立)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "FMU ：ｶﾊﾞ-部 開閉ｶﾊﾞ-前準備 (101-124）",
"WorkName": "開閉ｶﾊﾞｰ(傾斜部組立)",
"Words": [],
"WorkItems": [
"1. ①に②③を④BRACKET BOLT WASHER BOLT にて取付"
],
"WorkPoints": [
"接合面の隙間を最小に取付",
"接合面の隙間を最小に取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionItems": [],
"InspectionNos":... | [
{
"WorkName": "開閉ｶﾊﾞｰ(傾斜部組立)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"静電... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.