input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ前組み",
"Words": [],
"WorkItems": [
"1. BEARING にPIN を圧入する"
],
"WorkPoints": [
"治具にBEARING をｾｯﾄする",
"ﾃｰﾊﾟｰ側を上にして圧入",
"治具の上側を下側のﾋﾟﾝにはめ込む",
"PIN を挿入し圧入する"
],
"Tolks": [],
"InspectionItems": [],
"I... | [
{
"WorkName": "ﾍﾞｱﾘﾝｸﾞ前組み",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾌﾞﾛｯｸ前組み",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. 1完成品にPIN を圧入する",
"1. PLATE に砥石をかける"
],
"WorkPoints": [
"PIN を挿入し圧入する",
"ﾃｰﾊﾟｰ側を下にして圧入",
"治具にPLATE をｾｯﾄする",
"治具の上側を載せる",
"面取りが大きい方を上... | [
{
"WorkName": "ﾌﾞﾛｯｸ前組み",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Work... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ準備",
"Words": [],
"WorkItems": [
"1. BASE の指示部に油砥石をかける"
],
"WorkPoints": [
"指示部にﾊﾞﾘ･打痕無き事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"... | [
{
"WorkName": "ﾍﾞｰｽ準備",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_止めねじ取付け",
"Words": [],
"WorkItems": [
"1. ①にSCREW を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 35cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾍﾞｰｽ組立_止めねじ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ｽﾄｯﾊﾟｰ接着",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2"
],
"WorkItems": [
"▲1. ①にSTOPPER を接着する"
],
"WorkPoints": [
"接着穴に塗布する",
"面取り側から挿入する",
"飛び出した接着剤は拭き取ること"
],
"Tolks": [],
"InspectionItems": [],
"Inspectio... | [
{
"WorkName": "ﾍﾞｰｽ組立_ｽﾄｯﾊﾟｰ接着",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｽｰﾊﾟｰX(AX039)",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入1",
"Words": [],
"WorkItems": [
"1. ①にPIN を圧入する"
],
"WorkPoints": [
"㉖に①を搭載する",
"㉖にPIN を挿入する",
"上記完成品をｼﾞｸﾞ穴へ挿入する",
"ﾚﾊﾞｰを引いて圧入する",
"ﾃｰﾊﾟｰ側"
],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入1",
"QualityItem": "圧入確認",
"ToolManageNo": "FM-3032",
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入2",
"Words": [],
"WorkItems": [
"1. ①にPIN を圧入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
... | [
{
"WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入2",
"QualityItem": "圧入確認",
"ToolManageNo": "FM-6578",
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ(φ3_2㎜)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ｼｰﾄ貼付け",
"Words": [],
"WorkItems": [
"1. ①にSHEET を貼付ける"
],
"WorkPoints": [
"8㎜",
"面に合わせて貼付けのこと",
"8.5㎜",
"剥がれ無き事",
"面に合わせて貼付けのこと",
"上下共に､面に合わせてｶｯﾄする"
],
"Tolks": [],
"InspectionItems": ... | [
{
"WorkName": "ﾍﾞｰｽ組立_ｼｰﾄ貼付け",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WETE-G002-C13",
"Others": "-",
"ProcessNames": [
"-"
]
}
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ﾍﾞｱﾘﾝｸﾞ圧入",
"Words": [],
"WorkItems": [
"1. ①に②SPACER を取付ける"
],
"WorkPoints": [
"2箇所圧入する",
"反対側も同様に圧入する",
"①を㉗に搭載する",
"㉗のブロックで固定する",
"㉗の反対側に上記完成品を搭載しなおす"
],
"Tolks": [],
"InspectionItems": [... | [
{
"WorkName": "ﾍﾞｰｽ組立_ﾍﾞｱﾘﾝｸﾞ圧入",
"QualityItem": "圧入確認",
"ToolManageNo": "FM-6207",
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入ｼﾞｸﾞ(3ﾉｽﾞﾙﾍｯﾄﾞ)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_底面ﾍﾞｱﾘﾝｸﾞ取付け",
"Words": [],
"WorkItems": [
"1. ①にBEARING SPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsMod... | [
{
"WorkName": "ﾍﾞｰｽ組立_底面ﾍﾞｱﾘﾝｸﾞ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ﾌﾟﾚｰﾄ取付け",
"Words": [],
"WorkItems": [
"1. ①に②を挿入しBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾍﾞｰｽ組立_ﾌﾟﾚｰﾄ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾍﾞｰｽ組立_ｸﾞﾘｰｽ塗布",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"接着剤塗布 米粒:各1",
"接着剤塗布 米粒:各2"
],
"WorkItems": [
"◆1. ①のﾍﾞｱﾘﾝｸﾞとﾋﾟﾝにｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "ﾍﾞｰｽ組立_ｸﾞﾘｰｽ塗布",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2,各1・2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ面処理",
"Words": [],
"WorkItems": [
"1. GUIDE BLOCK BLOCK の全体に､軽く砥石をかける"
],
"WorkPoints": [
"ｴｯｼﾞ部にﾊﾞﾘ無き事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModel... | [
{
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ面処理",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ｼｬｯﾀｰ前組み",
"Words": [
"仮止め:SD-A051321-016にて本締め"
],
"WorkItems": [
"1. SHUTTER に②③④COLLAR をBOLT BOLT BOLT で仮取付けする",
"2. 1完成品を定盤上で仮締結する"
],
"WorkPoints": [
"隙間無い事",
"隙間無い事",
"面を合わせる事",
"面を合わせる事",
... | [
{
"WorkName": "ｼｬｯﾀｰ前組み",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ｼｬｯﾀｰ取付け1",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1",
"仮止め:SD-A051321-016にて本締め",
"仮止め:SD-A051321-016にて本締め",
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆2. SPRING WASHER にｸﾞﾘｰｽを塗布し⑤に貼付ける",
"1. ①に②を取付け､③COLLAR をBOLT で仮取付けする",
"... | [
{
"WorkName": "ｼｬｯﾀｰ取付け1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Wor... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ｼｬｯﾀｰ取付け2",
"Words": [],
"WorkItems": [
"3. ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が無い事を確認する",
"1. ①を定盤上で仮締結する",
"2. 1完成品のｼｬｯﾀｰ開閉時に､4つのﾍﾞｱﾘﾝｸﾞが回転する事を確認し本締結する"
],
"WorkPoints": [
"COLLAR以外を全て定盤に当付けて締結の事",
"隙間無い事",
"面を合わせる事",
... | [
{
"WorkName": "ｼｬｯﾀｰ取付け2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"Words": [],
"WorkItems": [
"1. ①にBLOCK BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"BLOCK BLOCK をﾋﾟﾝに挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け",
"Words": [
"㉙を黄緑の矢印方向に当付ける"
],
"WorkItems": [
"1. ①にSPACER をBOLT で取付ける",
"2. 1完成品にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG を仮取付けする",
"DOG をﾋﾟﾝｸの矢印方向に当付け取付ける"
],
"Tolks": [
"... | [
{
"WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "識別用ﾌﾞﾛｯｸ取付け",
"Words": [
"㉙を黄緑の矢印方向に当付ける"
],
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BLOCK を仮取付けする",
"BLOCK をﾋﾟﾝｸの矢印方向に当付け取付ける"
],
"Tolks": [],
"InspectionItems": [],
"Inspec... | [
{
"WorkName": "識別用ﾌﾞﾛｯｸ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾜｯｼｬｰ取付け",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
],
"WorkItems": [
"◆1. ①WASHER にｸﾞﾘｰｽを塗布する",
"2. 1完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [
"内側側面に塗布する",
"外周に塗布する"
],
"Tolks": [
"締付ﾄﾙｸ... | [
{
"WorkName": "ﾜｯｼｬｰ取付け",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1・ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "脱着・ｼｬｯﾀｰ動作確認",
"Words": [],
"WorkItems": [
"1. ①の脱着確認をする",
"2. ①のｼｬｯﾀｰの動作確認をする"
],
"WorkPoints": [
"引っ掛かり無き事",
"開くときの最大荷重をｽﾄﾛｰｸ全域で測定する",
"規格値:4.2N以下",
"ﾚﾊﾞｰを押す",
"自重落下する事"
],
"Tolks": [],
"Ins... | [
{
"WorkName": "脱着・ｼｬｯﾀｰ動作確認",
"QualityItem": "脱着確認",
"ToolManageNo": "FM-6553",
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾁｪｯｶｰ機構部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりが無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C13",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "ﾉｽﾞﾙｾｯﾄ確認",
"Words": [],
"WorkItems": [
"1. ﾉｽﾞﾙのｾｯﾄ確認をする"
],
"WorkPoints": [
"引っ掛かりなくｽﾑｰｽﾞである事",
"15ヵ所すべて確認する",
"ｼｬｯﾀｰを閉じた状態で､ﾉｽﾞﾙが抜け無い事"
],
"Tolks": [],
"InspectionItems": [
"検査表①:4.ﾉｽﾞﾙｾｯﾄ確認"
],
... | [
{
"WorkName": "ﾉｽﾞﾙｾｯﾄ確認",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C13",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャーユニット(FC03)(L)（001-",
"WorkName": "銘板貼付け",
"Words": [],
"WorkItems": [
"1. ①にLABEL LABEL LABEL ⑤を貼付ける"
],
"WorkPoints": [
"25㎜",
"2.5㎜",
"32㎜",
"0.5㎜",
"ｼｬｯﾀｰを開けて貼付ける",
"㉘を使用し貼付ける",
"30㎜",
"3㎜"
],
"Tolks": [],
"Inspec... | [
{
"WorkName": "銘板貼付け",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"W... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立①",
"Words": [
"表面",
"裏面"
],
"WorkItems": [
"1. BASE に油砥石をかける"
],
"WorkPoints": [
"表裏､指示部に油砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等を取除く"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
... | [
{
"WorkName": "ﾍﾞｰｽ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｽｰﾊﾟｰｼｬｲﾅ",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立②",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2"
],
"WorkItems": [
"▲1.②にSTOPPER を接着剤で取付ける"
],
"WorkPoints": [
"ｱﾙｺｰﾙで清掃後､②の取付穴にｽｰﾊﾟｰXを塗布し､STOPPER を取付ける",
"STOPPER の面取り側を②に向けて取付け",
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈ着用の事"
],
"Tol... | [
{
"WorkName": "ﾍﾞｰｽ組立②",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2個",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｽｰﾊﾟｰX",
"ProcessNames": [
"特殊工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立③",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1.②にPIN を取付ける"
],
"WorkPoints": [
"PIN PIN外周にグリスを塗布し、㉘で圧入する",
"PIN PINの面取り側を②へ向けて圧入する",
"PIN出代:6㎜"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ﾍﾞｰｽ組立③",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2個",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立④",
"Words": [
"28-2",
"28-1"
],
"WorkItems": [
"1. PLATE に砥石を掛ける",
"2. 1完成品にPIN を圧入"
],
"WorkPoints": [
"ﾋﾟﾝ圧入面の裏表面に掛ける事",
"2個製作",
"28-1にPLATE を入れる",
"穴の面取りが多きい面が上",
"28-2を被せる",... | [
{
"WorkName": "ﾍﾞｰｽ組立④",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "加工面に打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Work... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立⑤",
"Words": [],
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"圧入する",
"残り16本も同様に圧入する",
"残り3本も同様に圧入する",
"ﾋﾟﾝをﾃｰﾊﾟｰ側を下にして載せる",
"㉘を載せてからピンを挿入し圧入する",
"ﾃｰﾊﾟｰ側",
"㉙をピンに挿入する",
"②を㉗に載... | [
{
"WorkName": "ﾍﾞｰｽ組立⑤",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3031",
"ToolName": "Dﾋﾟﾝ圧入治具(表側)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立⑥",
"Words": [
"15mm",
"15mm",
"22mm",
"22mm",
"15mm",
"15mm"
],
"WorkItems": [
"1. ②にSHEET を貼付ける"
],
"WorkPoints": [
"貼付け面の清掃､脱脂を行う",
"緑色丸:長さ22㎜×6枚 端面合わせで貼付け",
"黄色丸:長さ15㎜×1... | [
{
"WorkName": "ﾍﾞｰｽ組立⑥",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ﾋﾟﾝｾｯﾄ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾐ､埃が無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Work... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立⑦",
"Words": [
"※D-pin(2ヶ所)と穴(2ヶ所)を はめ込む(赤矢印参照)"
],
"WorkItems": [
"1. 治具(FM-2250)にBEARING を挿入し 上治具をｾｯﾄする",
"2. 1.上治具の穴に､PIN を挿入･圧入する",
"3. 2.の上治具を外し､ SPACER を挿入する"
],
"WorkPoints": [
"治具･下側の列にﾍﾞｱﾘﾝ... | [
{
"WorkName": "ﾍﾞｰｽ組立⑦",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立⑧",
"Words": [],
"WorkItems": [
"1. ①に②を圧入する"
],
"WorkPoints": [
"①を㉗に搭載しブロックで固定する",
"㉗の反対側に搭載しなおし②を圧入する",
"㉘に搭載しなおし②を圧入する",
"ピンを㉘に挿入し矢印方向に当付ける",
"②を2ヵ所圧入する"
],
"Tolks": [],
"InspectionIt... | [
{
"WorkName": "ﾍﾞｰｽ組立⑧",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "圧入台",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Work... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾌﾞﾛｯｸ取付",
"Words": [],
"WorkItems": [
"1. ④に③をBOLT で取付ける",
"1. ④にBLOCK ､BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"④のPIN穴に③を挿入し取付け",
"③のPINにBLOCK ､BLOCK を挿入し取付け",
"PINの出代の長いほうを④に向ける"
],
"Tolks": [
"締付... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆2. 1.完成品のﾍﾞｱﾘﾝｸﾞ部にｸﾞﾘｰｽを塗布する",
"1. ③にBEARING SPACER をBOLT で取付ける"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄの頭のみにすること",
"ﾍﾞｱﾘﾝｸﾞ(大､小 各4個)にｸﾞﾘｰｽを塗布する"
],
... | [
{
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "周辺部品取付け面処理",
"Words": [],
"WorkItems": [
"1.GUIDE BLOCK BLOCK COLLAR に油砥石をかける"
],
"WorkPoints": [
"全体に油砥石をかけ､ﾊﾞﾘ等の無き事の確認を行う",
"油砥石は表面処理がはげない程度にかけること",
"GUIDE は全面に油砥石をかける",
"BLOCK BLOCK COLLAR は上下面に油砥石をかける"
... | [
{
"WorkName": "周辺部品取付け面処理",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ面処理",
"Words": [],
"WorkItems": [
"1. SHUTTER に油砥石をかける"
],
"WorkPoints": [
"表裏面のｴｯｼﾞ部分､穴加工部分に油砥石を軽くかけ､ﾊﾞﾘ等の無き事の確認を行う表面に傷が入らないように注意",
"表面:刻印あり穴加工部付近に油砥石をかける",
"裏面:刻印なし全体的に軽く油砥石をかける"
],
"Tolks": [],
"... | [
{
"WorkName": "ｼｬｯﾀｰ面処理",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ組立",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1"
],
"WorkItems": [
"◆2. 1.完成品にWASHER を貼付ける",
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を①にｼｬｯﾀｰに平行に取付ける",
"上面:刻印番号あり",
"青線部 ｼｬｯﾀｰとの隙間無い事",
"黄色面部 定盤上でｶﾞｲﾄﾞをｼｬｯ... | [
{
"WorkName": "ｼｬｯﾀｰ組立",
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ取付①",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆ 1.SPRING にｸﾞﾘｰｽを塗布する",
"2. ①の上に②をおく",
"3. 2.完成品にSPRING を挿入 ､③④をBOLT BOLT で仮取付け"
],
"WorkPoints": [
"表面全体にｸﾞﾘｰｽを塗布",
"①ｶﾞｲﾄﾞ穴にﾋﾟﾝを挿入",
"③... | [
{
"WorkName": "ｼｬｯﾀｰ取付①",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2個",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ取付②",
"Words": [],
"WorkItems": [
"1.①に②③をBOLT BOLT で仮取付け",
"2.1.完成品に④をBOLT で仮取付け"
],
"WorkPoints": [
"本締め: SD-052599-016",
"本締め: SD-052599-016"
],
"Tolks": [],
"InspectionItems": [],
"Inspection... | [
{
"WorkName": "ｼｬｯﾀｰ取付②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視手感",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ取付③",
"Words": [
"裏面",
"表面",
"定盤",
"定盤"
],
"WorkItems": [
"2.仮締めﾎﾞﾙﾄを締結する(緑丸6か所)",
"2. ﾍﾞｱﾘﾝｸﾞの当たり調整",
"3. ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が無い事を確認する"
],
"WorkPoints": [
"ｼｬｯﾀｰを左右に動作時※ﾍﾞｱﾘﾝｸﾞに空回りが無く､4か... | [
{
"WorkName": "ｼｬｯﾀｰ取付③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｬｯﾀｰ動作確認",
"Words": [],
"WorkItems": [
"1. ①ｼｬｯﾀｰの動作確認を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰをﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞで押して､開く時のｽﾄﾛｰｸ全域での最大荷重を測定する※この確認はあくまでの最終検査前の事前確認です",
"目安値: 4.2N 以下",
"最終検査はSD-A052599-022にて実施",
"①を㉖冶具(FM-65... | [
{
"WorkName": "ｼｬｯﾀｰ動作確認",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6553",
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾁｪｯｶｰ機構部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "周辺部品取付",
"Words": [
"㉙を黄緑の矢印方向に当付ける"
],
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付け",
"2.. ①にSPACER をBOLT で取付け"
],
"WorkPoints": [
"DOG を仮取付する",
"SPACER をﾋﾟﾝｸの矢印方向に当付け取付ける"
],
"Tolks": [
"締付ﾄﾙｸ ... | [
{
"WorkName": "周辺部品取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾍﾞｰｽ組立⑨",
"Words": [
"･内面(側面)に ｸﾞﾘｰｽを塗布する",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
],
"WorkItems": [
"◆1. ①WASHER にｸﾞﾘｰｽを塗布する",
"2. WASHER をBOLT WASHER で取付ける",
"3. COLLAR をBOLT で取付ける"
],
"WorkPoints": []... | [
{
"WorkName": "ﾍﾞｰｽ組立⑨",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各各95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ﾌﾞﾛｯｸ取付",
"Words": [
"裏面",
"㉚を黄緑の矢印方向に当付ける"
],
"WorkItems": [
"1.①にBLOCK をBOLT WASHER で取付け",
"2.①にSCREW を取付け"
],
"WorkPoints": [
"BLOCK をﾋﾟﾝｸの矢印方向に当付け取付ける",
"BLOCK を仮取付けする"
],
"Tolks": [
"... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "銘板貼付",
"Words": [
"0.5mm",
"1mm",
"1mm",
"2.5mm",
"32mm",
"30mm",
"3mm",
"25mm"
],
"WorkItems": [
"■1. ①にLABEL LABEL LABEL ⑨を貼付ける"
],
"WorkPoints": [
"指示箇所にﾗﾍﾞﾙを貼付け､剥がれが無い事を確認する",... | [
{
"WorkName": "銘板貼付",
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付けられている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "機能検査①",
"Words": [],
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"2. ｼｬｯﾀｰ動作確認"
],
"WorkPoints": [
"･ｽﾄﾛｰｸ全域で最大荷重を測定する",
"規格値:4.2N以下",
"引っ掛かり無き事",
"ﾚﾊﾞｰを押す",
"自重落下する事"
],
"Tolks": [],
"Inspection... | [
{
"WorkName": "機能検査①",
"QualityItem": "脱着確認",
"ToolManageNo": "FM-6553",
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾁｪｯｶｰ機構部",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりが無い事",
"Method": "手感",
"RecordMethod": "WETE-G002-C22",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "機能検査②",
"Words": [
"ｼｬｯﾀｰ右側面",
"BASE右側段差側面",
"表面",
"裏面"
],
"WorkItems": [
"1. ｼｬｯﾀｰ位置調整",
"2. ﾉｽﾞﾙｾｯﾄ確認"
],
"WorkPoints": [
"･ｼｬｯﾀｰを開いてﾉｽﾞﾙが11ヵ所すべてにｽﾑｰｽﾞにｾｯﾄ出来ること確認",
"･ｼｬｯﾀｰが閉じた状態で､右側の隙間が均... | [
{
"WorkName": "機能検査②",
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolName": "ﾀﾞﾐｰﾉｽﾞﾙ(3ﾉｽﾞﾙ用)",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C22",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ノズルチェンジャー：L（FC03シールドノズル対応）（001-",
"WorkName": "ｼｰﾄ確認",
"Words": [
"ｼｰﾄ"
],
"WorkItems": [
"1. シート（傷防止）が剝がれていないことを確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [
"検査表①:ｼｰﾄ(傷防止)貼付確認"
],
"InspectionNos": [
"WETE-G002-C22"
],
"Wo... | [
{
"WorkName": "ｼｰﾄ確認",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷等が無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C22",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける",
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
... | [
{
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"WorkN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"Words": [
"表 面",
"裏 面"
],
"WorkItems": [
"2. PLATE の平面度を測定する",
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙﾐ用砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"Words": [
"FM-5626"
],
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BRACK... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"Words": [
"面取り",
"面取り"
],
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前に... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_共通(Front側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"Words": [],
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"Inspection... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"Words": [
"この作業では同じものを4個製作"
],
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける",
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
... | [
{
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"WorkN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"Words": [
"表 面",
"裏 面"
],
"WorkItems": [
"2. PLATE の平面度を測定する",
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙﾐ用砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"Words": [
"FM-5626"
],
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BR... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"2箇所の取付調整を行う事",
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"InspectionNos": ... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"Words": [
"面取り",
"面取り"
],
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_デュアル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"Words": [],
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"Inspect... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける",
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"Inspecti... | [
{
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"WorkN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"Words": [
"表 面",
"裏 面"
],
"WorkItems": [
"2. PLATE の平面度を測定する",
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙﾐ用砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"Words": [
"FM-5626"
],
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BR... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉖の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"Words": [
"面取り",
"面取り"
],
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：基板下受けブロック一括交換式_シングル対応(Rear側)（001-",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"Words": [],
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems": [],
"Inspect... | [
{
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "本体側ｼｭｰﾄ組立",
"Words": [
"裏面"
],
"WorkItems": [
"1. CHUTE にBRACKET BRACKET をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Ji... | [
{
"WorkName": "本体側ｼｭｰﾄ組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立①",
"Words": [],
"WorkItems": [
"1. PLATE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"下側端面を合わせる"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立②",
"Words": [
"端面"
],
"WorkItems": [
"1. ①にPLUNGER を取付ける"
],
"WorkPoints": [
"この部分が端面から出ない所で固定する"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立③",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1"
],
"WorkItems": [
"2. ③に1.完成品をBOLT WASHER で取付ける",
"◆1. COLLAR にｸﾞﾘｰｽを塗布しSTAY へ挿入する"
],
"WorkPoints": [
"COLLAR COLLARの周囲に㉖を薄く均等に塗布する",
"㉖グリース塗布後、挿入する"
],
"Tolks": [],
"I... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立③",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立④",
"Words": [
"端面"
],
"WorkItems": [
"2. 1.完成品にPIN を挿入する",
"1. BRACKET にPLUNGER を取付ける"
],
"WorkPoints": [
"この部分が端面から出ない所で固定する",
"ｽﾌﾟﾘﾝｸﾞﾋﾟﾝの出代と方向に注意する"
],
"Tolks": [],
"InspectionItems": [],
"Ins... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立④",
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑤",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1"
],
"WorkItems": [
"2. ③に1.完成品をBOLT WASHER で取付ける",
"◆1. COLLAR にｸﾞﾘｰｽを塗布しSTAY へ挿入する"
],
"WorkPoints": [
"COLLAR COLLARの周囲に㉖を薄く均等に塗布する",
"㉖グリース塗布後、挿入する",
"この面の平行を合わせる(目視)"
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑤",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑥",
"Words": [],
"WorkItems": [
"1. CHUTE に②③をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安全作業"
],
"ToolPartsModels": [
{
"... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑥",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P2(001-008)",
"WorkName": "支給品",
"Words": [
"ｼｰﾙを剥がす",
"1.完成品",
"②本体側ｼｭｰﾄ完成品",
"③ﾕﾆｯﾄ側ｼｭｰﾄ完成品",
"取付用部材六角穴付きﾎﾞﾙﾄ M6×12(4P)厚肉座金 M6(4P)",
"2個",
"取付用部材六角穴付きﾎﾞﾙﾄ M6×25(1P)六角穴付きﾎﾞﾙﾄ M6×16(2P)厚肉座金 M6(3P)"
],
"WorkItems": [
"2. 本体部ﾄﾞｯｷﾝｸﾞ工程へ支給する... | [
{
"WorkName": "支給品",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立横",
"Words": [
"1.完成品",
"M6",
"M5",
"M4",
"M3",
"×3",
"×2"
],
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT NUT CABLE-SUPPORT を取付",
"2. 1.完成品にBRACKET をBOLT ･WASHER で取付"
],
"WorkPoints": [
"... | [
{
"WorkName": "ﾌﾚｰﾑ組立横",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立縦",
"Words": [
"M6",
"M5",
"M4",
"M3",
"1.完成品",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付",
"2. 1.完成品にBRACKET をBOLT ･WASHER で取付"
],
"WorkPoints": [
"左面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立縦",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT ･WASHER で取付",
"2. ㉘にBOLT ・WASHER (各8個)を入れマスキングテープで止め同梱"
],
"WorkPoints": [
"ﾌﾚｰﾑ面に段差無き事",
"正面",
"背面",
"上面"
],
"Tolks": [],
"Insp... | [
{
"WorkName": "ﾌﾚｰﾑ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "HEPA組立①",
"Words": [
"1.完成品"
],
"WorkItems": [
"2. BLOWER の取付ﾌﾞﾗｹｯﾄを1.完成品と交換し取り外したﾎﾞﾙﾄとWASHER で固定",
"1. BRACKET のブラケット1個に㉖カプトンテープを貼付け"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で下面を合わせて固定する",
"BRACK... | [
{
"WorkName": "HEPA組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "HEPA組立②",
"Words": [],
"WorkItems": [
"2. BOLT ・WASHER ・WASHER を㉖に入れマスキングテープで止め同梱",
"1. ①にGASKET ･GASKET ･GASKET を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolP... | [
{
"WorkName": "HEPA組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"Words": [
"1.完成品"
],
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. COVER に1.完成品･GROMMET を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"Words": [],
"WorkItems": [
"1. COVER にGROMMET を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立横",
"Words": [
"1.完成品",
"M6",
"M5",
"M4",
"M3",
"×3",
"×2"
],
"WorkItems": [
"1. ①に②③④⑤⑥を取付",
"2. 1.完成品に⑦を⑯⑧で取付"
],
"WorkPoints": [
"背面",
"上面",
"正面",
"下面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立横",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立縦",
"Words": [
"M6",
"M5",
"M4",
"M3",
"1.完成品",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②③を取付",
"2. 1.完成品に④を⑯⑤で取付"
],
"WorkPoints": [
"左面",
"上面",
"正面",
"下面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立縦",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を⑯③で取付",
"2. ㉘に⑯③(各8個)を入れマスキングテープで止め同梱"
],
"WorkPoints": [
"ﾌﾚｰﾑ面に段差無き事",
"正面",
"背面",
"上面"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ﾌﾚｰﾑ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "HEPA組立①",
"Words": [
"1.完成品"
],
"WorkItems": [
"2. ②の取付ﾌﾞﾗｹｯﾄを①･1.完成品と交換し取り外したﾎﾞﾙﾄで固定",
"1. ①のﾌﾞﾗｹｯﾄ1個に④ｶﾌﾟﾄﾝﾃｰﾌﾟを貼付け"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で下面を合わせて固定する",
"①の曲げが下側",
"下面... | [
{
"WorkName": "HEPA組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "HEPA組立②",
"Words": [],
"WorkItems": [
"2. ⑯⑰⑤を㉖に入れマスキングテープで止め同梱",
"1. ①に②③④を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguN... | [
{
"WorkName": "HEPA組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"Words": [
"1.完成品"
],
"WorkItems": [
"1. ①に切り込みを入れる",
"2. ②に1.完成品･③を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPart... | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P2(001-007)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"Words": [],
"WorkItems": [
"1. ①に②を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"Words": [
"FM-5626",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. 1完成品をPLATE にBOLT で取付ける",
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける",
"取付け方向に注意する事(面取り側)",
"表面",
"裏面"
],
"Tolks": [... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具との隙間:0.05㎜が入ら無い事",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立4(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPa... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立4(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolName": "基板下受け組立台",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"Words": [
"❶",
"❷",
"❺",
"❸",
"❹",
"⓬",
"❻",
"❼",
"❽",
"❾",
"❿",
"⓫",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],... | [
{
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolName": "平面度測定ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にWASHER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkT... | [
{
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"Words": [
"FM-5626",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"矢印方向に押えて固定の事",
... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionItems"... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具をｾｯﾄする",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固定の事",
... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に⑱を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPa... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolName": "基板下受け組立台",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"Words": [
"❶",
"❷",
"❺",
"❸",
"❹",
"⓬",
"❻",
"❼",
"❽",
"❾",
"❿",
"⓫",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],... | [
{
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolName": "平面度測定ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.