input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にWASHER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkT... | [
{
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_デュアルコンベヤー:NPM-GW（001-",
"WorkName": "製造手配銘板貼付け",
"Words": [
"100±2㎜",
"120±2㎜",
"100±2㎜",
"120±2㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
".",
"2. ①と②に③を貼付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの裏面(部品取付面)に貼付ける事",
"REAR",
"FRON... | [
{
"WorkName": "製造手配銘板貼付け",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "本体側ｼｭｰﾄ組立",
"Words": [
"裏面"
],
"WorkItems": [
"1. CHUTE にBRACKET BRACKET をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Ji... | [
{
"WorkName": "本体側ｼｭｰﾄ組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立①",
"Words": [],
"WorkItems": [
"1. PLATE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"下側端面を合わせる"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立②",
"Words": [
"端面"
],
"WorkItems": [
"1. ①にPLUNGER を取付ける"
],
"WorkPoints": [
"この部分が端面から出ない所で固定する"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立③",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1"
],
"WorkItems": [
"2. ③に1.完成品をBOLT WASHER で取付ける",
"◆1. COLLAR にｸﾞﾘｰｽを塗布しSTAY へ挿入する"
],
"WorkPoints": [
"COLLAR COLLARの周囲に㉖を薄く均等に塗布する",
"㉖グリース塗布後、挿入する"
],
"Tolks": [],
"I... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立③",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立④",
"Words": [
"端面"
],
"WorkItems": [
"2. 1.完成品にPIN を挿入する",
"1. BRACKET にPLUNGER を取付ける"
],
"WorkPoints": [
"この部分が端面から出ない所で固定する",
"ｽﾌﾟﾘﾝｸﾞﾋﾟﾝの出代と方向に注意する"
],
"Tolks": [],
"InspectionItems": [],
"Ins... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立④",
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑤",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1"
],
"WorkItems": [
"2. ③に1.完成品をBOLT WASHER で取付ける",
"◆1. COLLAR にｸﾞﾘｰｽを塗布しSTAY へ挿入する"
],
"WorkPoints": [
"COLLAR COLLARの周囲に㉖を薄く均等に塗布する",
"㉖グリース塗布後、挿入する",
"この面の平行を合わせる(目視)"
... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑤",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑥",
"Words": [
"950㎜",
"950㎜"
],
"WorkItems": [
"2. CHUTE に1.完成品を貼付ける",
"1. GASKET を下記寸法にｶｯﾄする"
],
"WorkPoints": [
"貼付け前に脱脂すること",
"端面を合わせる"
],
"Tolks": [],
"InspectionItems": [],
"InspectionN... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑥",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
... | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑦",
"Words": [],
"WorkItems": [
"1. ①に②③をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [
"◆作業者安全作業"
],
"ToolPartsModels": [
{
"JiguN... | [
{
"WorkName": "ﾕﾆｯﾄ側ｼｭｰﾄ組立⑦",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:シート廃棄部:P1(001-009)",
"WorkName": "支給品",
"Words": [],
"WorkItems": [
"2. 本体部ﾄﾞｯｷﾝｸﾞ工程へ支給する",
"1. BOX のｼｰﾙを剥がす"
],
"WorkPoints": [
"全体に傷や割れが無いか確認する(2個)",
"ｼｰﾙを剥がす",
"1.完成品",
"②本体側ｼｭｰﾄ完成品",
"③ﾕﾆｯﾄ側ｼｭｰﾄ完成品",
"取付用部材六角穴付きﾎﾞﾙﾄ M6×12(4P)厚肉座金 M6(4P)"... | [
{
"WorkName": "支給品",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"作業者安全工程"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"Words": [
"FM-5626",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"治具との隙間:0.05㎜が入ら無い事",
"表... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立1(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"①に治具をｾｯﾄする",
"BLOCK を治具に挿入し取付ける",
"取付け方向に注意する事(面取り側)",
"表面",
"裏面"
],
"Tolks": [... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立2(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具をｾｯﾄする",
"治具との隙間:0.05㎜が入ら無い事",
"治具のﾅｯﾄ向きに注意する事",
"矢印方向に押さえて固... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立3(F側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立4(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPa... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立4(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE(NPM-GW) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"ﾌﾟﾚｰﾄ間の隙間①~④:0.1㎜が入り､0.3㎜が入ら無い事ﾎﾞﾙﾄとﾌﾟﾚｰﾄの隙間⑤~⑧:0.5㎜が入る事",... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立5(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolName": "基板下受け組立台",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"Words": [
"❶",
"❷",
"❺",
"❸",
"❹",
"⓬",
"❻",
"❼",
"❽",
"❾",
"❿",
"⓫",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],... | [
{
"WorkName": "ﾌﾟﾚｰﾄ測定(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolName": "平面度測定ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(F側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にWASHER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkT... | [
{
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(F側)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"Words": [
"FM-5626",
"FM-5626",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にCAM-FOLLOWER をWASHER WASHER NUT で取付ける",
"2. 1完成品をPLATE にBOLT で取付ける"
],
"WorkPoints": [
"表面",
"矢... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立1(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"取付け方向に注意する事(面取り側)",
"裏面",
"表面",
"表面から①BLOCK に治具を挿入し､BOLT を締め付ける",
"裏面"
],
"Tolk... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立2(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"①にBRACKET を仮取付けする",
"治具のﾅｯﾄ向きに注意する事",
"治具との隙間:0.05㎜が入ら無い事",
"BRACKET ﾌﾞﾗｹｯﾄの取付方向に注意する事",... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立3(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE(NPM-GW SINGLE CONVEYOR) をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"ﾅｯﾄの2度締めを行うこと(緩み防止)",
"FM-3433",
"ﾌﾟﾚｰﾄ間 0.2㎜のｼｯｸﾈｽｹﾞｰｼﾞを挟み込... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立4(R側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-3433",
"ToolName": "基板下受け組立台",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. ①の平面度を測定する"
],
"WorkPoints": [
"平面度:-0.20㎜~+0.10㎜",
"一番高い所を0(基準)とする",
"測定位置❶～⓰に測定シャフトを置きその上を測定する（皿ネジ近傍の内より側）",
... | [
{
"WorkName": "ﾌﾟﾚｰﾄ測定(R側)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5001",
"ToolName": "平面度測定ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(R側)",
"Words": [
"この作業では同じものを2個製作",
"削除"
],
"WorkItems": [
"1. ①にWASHER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionNos": []... | [
{
"WorkName": "誤挿入防止ﾎﾞﾙﾄ取付(R側)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：下受けブロック自動交換_シングルコンベヤー:NPM-GW（001-",
"WorkName": "製造手配銘板貼付け",
"Words": [
"100±2㎜",
"120±2㎜",
"100±2㎜",
"120±2㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①と②に③を貼付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの裏面(部品取付面)に貼付ける事",
"REAR",
"FRONT"
],
... | [
{
"WorkName": "製造手配銘板貼付け",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立横",
"Words": [
"1.完成品",
"M6",
"M5",
"M4",
"M3",
"×3",
"×2"
],
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT NUT CABLE-SUPPORT を取付",
"2. 1.完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"背... | [
{
"WorkName": "ﾌﾚｰﾑ組立横",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立縦",
"Words": [
"M6",
"M5",
"M4",
"M3",
"1.完成品",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付",
"2. 1.完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"左面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立縦",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"2. ㉘にBOLT WASHER (各8個)を入れマスキングテープで止め同梱"
],
"WorkPoints": [
"ﾌﾚｰﾑ面に段差無き事",
"正面",
"背面",
"上面"
],
"Tolks": [],
"Inspec... | [
{
"WorkName": "ﾌﾚｰﾑ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "HEPA組立",
"Words": [
"1.完成品"
],
"WorkItems": [
"3. BOLT WASHER WASHER (残り2個)を㉙に入れマスキングテープで止め同梱",
"2. BLOWER の取付ﾌﾞﾗｹｯﾄを1.完成品と交換し取り外したﾎﾞﾙﾄで固定",
"1. BRACKET のﾌﾞﾗｹｯﾄ2個にTAPE ｶﾌﾟﾄﾝﾃｰﾌﾟを貼付け"
],
"WorkPoints": [
"4ヶ所",
"交... | [
{
"WorkName": "HEPA組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"Words": [
"1.完成品"
],
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. COVER に1.完成品･GROMMET を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"Words": [],
"WorkItems": [
"1. COVER にGROMMET を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立横",
"Words": [
"1.完成品",
"M6",
"M5",
"M4",
"M3",
"×3",
"×2"
],
"WorkItems": [
"1. ①に②③④⑤⑥を取付",
"2. 1.完成品に⑦を⑯⑧で取付"
],
"WorkPoints": [
"背面",
"上面",
"正面",
"下面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立横",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立縦",
"Words": [
"M6",
"M5",
"M4",
"M3",
"1.完成品",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②③を取付",
"2. 1.完成品に④を⑯⑤で取付"
],
"WorkPoints": [
"左面",
"上面",
"正面",
"下面",
"上面",
... | [
{
"WorkName": "ﾌﾚｰﾑ組立縦",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ組立",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を⑯③で取付",
"2. ㉘に⑯③(各8個)を入れマスキングテープで止め同梱"
],
"WorkPoints": [
"ﾌﾚｰﾑ面に段差無き事",
"正面",
"背面",
"上面"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ﾌﾚｰﾑ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "HEPA組立",
"Words": [
"1.完成品"
],
"WorkItems": [
"3. ⑯⑰③(残り2個)を㉘に入れマスキングテープで止め同梱",
"2. ②の取付ﾌﾞﾗｹｯﾄを①･1.完成品と交換し取り外したﾎﾞﾙﾄで固定",
"1. ①のﾌﾞﾗｹｯﾄ2個に④ｶﾌﾟﾄﾝﾃｰﾌﾟを貼付け"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で... | [
{
"WorkName": "HEPA組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"Words": [
"1.完成品"
],
"WorkItems": [
"1. ①に切り込みを入れる",
"2. ②に1.完成品･③を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPart... | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "305CG逆流れ:HEPAフィルター:P1(001-006)",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"Words": [],
"WorkItems": [
"1. ①に②を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": []
} | [
{
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｵｲﾙﾊﾟﾝ組立",
"Words": [
"この部分を持ってﾋﾞｰﾑを移動し無い事 /Do not move an X beam with this part / □□□□□□□□□□□□□□",
"396㎜",
"1㎜",
"接着剤塗布 1ﾄﾘﾑにつきｺﾞﾏ粒:6",
"①",
"②",
"④",
"③",
"⑤",
"⑥",
"この作業では同じものを2個製作",
"②",
"①",
... | [
{
"WorkName": "ｵｲﾙﾊﾟﾝ組立",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①",
"Words": [
"裏 面",
"表 面",
"2.5㎜",
"表 面",
"2.5㎜",
"表 面",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. PLATE の両面に砥石をかける",
"2. 1完成品にPIN を圧入する(4箇所)"
],
"WorkPoints": [
"ﾋﾟﾝ圧入面(ｻﾞｸﾞﾘ穴側)と圧入方向に注意する",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②",
"Words": [
"7mm",
"表 面",
"裏 面",
"7mm",
"5mm"
],
"WorkItems": [
"1. X-PLATE の両面に砥石をかける",
"2. X-PLATE にPIN を圧入する"
],
"WorkPoints": [
"表裏でﾋﾟﾝ出代が違うので注意する事",
"この作業では同じものを2個製作",
"PIN ﾋﾟﾝ出代:7㎜",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立③",
"Words": [
"A視点",
"B視点"
],
"WorkItems": [
"1. ①にCLIP BOLT を取付ける"
],
"WorkPoints": [
"表 :4箇所",
"B視点",
"A視点",
"この作業では同じものを2個製作",
"CLIP の取付方向や位置を間違えないように取付ける事(下図参照)",
"このﾏｳﾝﾄは矢印方向に当てつけて取付ける",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④",
"Words": [],
"WorkItems": [
"■3. FAN の型式を確認し､ｼﾘｱﾙ番号を転記",
"1. ①にSTOPPER SPACER をBOLT で取付ける",
"2. FAN にLABEL を取付ける",
"4. 1完成品に2完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"ﾌｧﾝの銘板が下になるようにして取付ける事",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑤",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にBOLT を挿入する",
"2. 1完成品にWASHER BOLT を取付ける",
"3. 2完成品に③をWASHER BOLT で取付"
],
"WorkPoints": [
"③を矢印方向に押し当てる事",
"WASHER をBOLT の方向に当てつけて取付ける事"
],
"Tolks": [... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑤",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥",
"Words": [
"この作業では同じものを2個製作",
"11mm"
],
"WorkItems": [
"1. PIN にBOLT WASHER を挿入する",
"2.1完成品を①に挿入する",
"3. 2完成品にSCREW を取付ける"
],
"WorkPoints": [
"Dｶｯﾄ面を矢印方向に向ける",
"Dｶｯﾄ面",
"PIN のﾋﾟﾝの出代が11㎜になるように取付ける"
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆",
"Words": [
"型式",
"Ser.No"
],
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"2. ①にMOTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"MOTOR のﾓｰﾀ線は左側から出る様に取付ける事"
],
"Tolks": [
"締付ﾄ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆",
"QualityItem": "型式確認･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C09",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①",
"Words": [
"Ser.No.型式",
"S/N ※※※※※※※",
"Model ST748C-0980E-PF",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を検査書に転記する",
"2. 橙色の斜線部分に砥石をかける",
"3. BRACKET にBOLT WASHER を差込む",
"4. B... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①",
"QualityItem": "型式確認･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C09",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②",
"Words": [
"60㎜",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①のｴﾝｺｰﾀﾞｰ線の60㎜位置にﾏｰｸする(ｲﾝｼｭﾛｯｸ固定位置)",
"2. 1完成品にCLIP をBOLT で取付ける",
"3. 2完成品の配線を㉙インシュロックで固定する"
],
"WorkPoints": [
... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①",
"Words": [
"この作業では同じものを8個製作"
],
"WorkItems": [
"1. BLOCK のGREASE-NIPPLE JOINT 取付面にｱﾙｶﾝｻｽをかける",
"2. BLOCK にGREASE-NIPPLE を取付ける",
"3. 2完成品にJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立銘板",
"Words": [
"B矢視",
"8㎜",
"18㎜",
"A矢視",
"30㎜",
"5㎜",
"7㎜",
"1.5㎜",
"7㎜",
"1.5㎜"
],
"WorkItems": [
"1. BRACKET BRACKET にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立銘板",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾄﾞﾛｱｺﾈｸﾀｰ組立",
"Words": [
"11㎜",
"7㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"3. 2完成品にBRACKET BRACKET をBOLT で仮付けする",
"2. COUPLER にBRACKET をSPACER BOLT WASHER で取付ける",
"1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [
"本締工程:... | [
{
"WorkName": "ﾍｯﾄﾞﾄﾞﾛｱｺﾈｸﾀｰ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②",
"Words": [
"3mm",
"この作業では同じものを2個製作",
"1mm",
"接着剤塗布 ｺﾞﾏ粒:2"
],
"WorkItems": [
"1. ①にCOVER を貼付ける",
"2. ①にSHEET SHEET を貼付ける",
"▲3. 2完成品にWASHER を貼付ける"
],
"WorkPoints": [
"ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をSCREW WASHER BOLT で仮付けする",
"2. 1完成品にWASHER BOLT を固定する",
"3. 2完成品をWASHER BOLT で固定する"
],
"WorkPoints": [
"面に合わして仮付けする(黄緑色線)",
"ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)"
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④",
"Words": [
"2㎜",
"2㎜",
"2㎜",
"3㎜",
"この作業では同じものを2個製作",
"12㎜",
"3㎜",
"2㎜",
"2㎜"
],
"WorkItems": [
"1. ①にCOVER COVER COVER COVER を貼付ける",
"2. SPACER にSCREW を挿入する",
"3. ①に2完成品を挿入しSPACER を締... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑤",
"Words": [
"②の取付位置(向き)に気を付ける事",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にCLIP をBOLT で取付ける",
"2. 1完成品にCABLE-SUPPORT をBOLT で固定する"
],
"WorkPoints": [
"縦向きにし､仮付けすること",
"ﾏｳﾝﾄはSD‐A051867‐047で本締め"
],
"Tolks"... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑤",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑥",
"Words": [
"矢印の方向に当てつけて取付ける事",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で固定する",
"2. 1完成品にBRACKET をBOLT で固定する"
],
"WorkPoints": [
"②の向きに注意し平行に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m",
"締付ﾄ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑥",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ・ｽﾄｯﾊﾟｰ組立",
"Words": [
"2㎜",
"14.5㎜",
"37.5㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. BRACKET にCOVER を取付ける",
"2. 1完成品とBRACKET に①をBOLT WASHER で取付ける",
"3. NUT にSCREW を取付ける",
"4. 3完成品にSTOPPER を取付ける"
],
... | [
{
"WorkName": "X軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ・ｽﾄｯﾊﾟｰ組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "X軸ﾍﾞｱ受け組立",
"Words": [
"A矢視図",
"350mm",
"この部分を持って･･･",
"ｽﾗｲﾄﾞ",
"ｽﾗｲﾄﾞ",
"10㎜",
"35㎜",
"25㎜",
"1㎜",
"接着剤塗布 ｺﾞﾏ粒:各2",
"A矢視",
"この作業では同じものを2個製作"
],
"WorkItems": [
"▲4. 3完成品にWASHER を貼付ける",
"2. ... | [
{
"WorkName": "X軸ﾍﾞｱ受け組立",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"Words": [
"8mm",
"12mm",
"14mm"
],
"WorkItems": [
"1. BRACKET にCOVER COVER を取付ける",
"2. 1完成品にLABEL を貼付ける",
"3. 2完成品にCLIP BOLT を取付ける"
],
"WorkPoints": [
"COVER をBRACKET に当てつけて取付ける",
"この作業はR側のみ行う"... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"Words": [
"長い",
"短い",
"短い",
"長い"
],
"WorkItems": [
"1. ①BRACKET にBRACKET をSCREW で取付ける",
"2. 1完成品にROD をBOLT WASHER SCREW で固定する",
"3. 2完成品にROD を取付ける"
],
"WorkPoints": [
"ﾊﾞﾘがある場合はｱﾙｶﾝｻｽをかける",
... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立②",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立③",
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2",
"仮止め:SD-A051867-048にて本締め"
],
"WorkItems": [
"1. ①②にBRACKET をSCREW BOLT WASHER で取付ける",
"2. 1完成品にBRACKET をSCREW で仮付けする",
"▲3. 2完成品にWASHER を貼付ける"
],
"WorkPoints": [
"①(②)とWASHER の円... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ組立③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "BEAM加工面確認",
"Words": [
"A",
"E",
"C",
"D",
"B",
"F",
"G",
"砥石かけ面"
],
"WorkItems": [
"1. X-BEAM の加工面に砥石をかける"
],
"WorkPoints": [
"D矢視 (C矢視同様)",
"G矢視 (F矢視同様)",
"A矢視",
"C矢視",
"E矢視",
... | [
{
"WorkName": "BEAM加工面確認",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "ｱﾙｶﾝｻｽ",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷、ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "PIN圧入",
"Words": [
"5mm",
"2mm",
"2mm",
"2.5mm"
],
"WorkItems": [
"1. ①にPIN PIN を圧入する"
],
"WorkPoints": [
"PIN ﾋﾟﾝの出代:5㎜",
"PIN ﾋﾟﾝ出代:2.5㎜",
"PIN ﾋﾟﾝの出代:2㎜測定箇所に注意する事(図参照)",
"この作業では同じものを2個製作",
"ﾋﾟﾝの出代に注意す... | [
{
"WorkName": "PIN圧入",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"W... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "銘板貼付け①",
"Words": [
"ﾊﾝﾄﾞﾙを持ってﾋﾞｰﾑを移動させること/･･",
"3mm",
"120mm",
"120mm",
"Be careful.Metal product, such as wrench or bolt,",
"中国文",
"ﾚﾝﾁ､ﾎﾞﾙﾄ等の金属類は磁力にとって強力吸引さ",
"Be careful.Metal product, such as wrench or bolt... | [
{
"WorkName": "銘板貼付け①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｶｰﾎﾞﾝﾌﾟﾚｰﾄ取付、F・R銘板貼付け",
"Words": [
"F",
"R",
"390㎜",
"F",
"30㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にPLATE をBOLT で取付ける",
"2. 1完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付け面は脱脂する事"
],
"Tolks": [
"締... | [
{
"WorkName": "ｶｰﾎﾞﾝﾌﾟﾚｰﾄ取付、F・R銘板貼付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessName... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "銘板貼付け②",
"Words": [
"この作業では同じものを2個製作",
"10mm",
"4mm",
"3㎜",
"F側",
"R側",
"F側",
"R側",
"X軸(R側)",
"㉙で貼付ける事",
"接着剤塗布 小豆:3",
"10mm",
"4mm",
"2㎜"
],
"WorkItems": [
"▲2. 1の完成品にLABEL を㉙で貼付ける",
... | [
{
"WorkName": "銘板貼付け②",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾏｳﾝﾄ取付",
"Words": [
"A矢視",
"A矢視",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にCLIP BOLT を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向きに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"... | [
{
"WorkName": "ﾏｳﾝﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "板金取付",
"Words": [],
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"矢印(黄色)方向に押し当てながら取付ける",
"内側に当てつけて取付ける",
"BRACKET には向きがあるので注意する事",
"長い",
... | [
{
"WorkName": "板金取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ取付①",
"Words": [
"IKO",
"ser.No",
"RX002",
"RX001",
"この作業では同じものを2個製作",
"ｸﾞﾘｰｽ塗布 小豆:各5"
],
"WorkItems": [
"2. 防錆油を拭き取る",
"1. LINEAR-WAY のｼﾘｱﾙNo.の組合わせを確認し､ｽﾗｲﾀﾞｰﾌﾞﾛｯｸが動かないように注意して開梱する",
"3. LINEAR-WAY の基準面と取付面... | [
{
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ取付①",
"QualityItem": "ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C09",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ取付②",
"Words": [
"PIN",
"ﾘﾆｱｶﾞｲﾄﾞ基準位置",
"RY002",
"RY001",
"RX002",
"RX001",
"基準ﾋﾟﾝ位置",
"基準",
"基準",
"上段ﾚｰﾙ基準側",
"下段ﾚｰﾙ従動側",
"この作業では同じものを2個製作",
"仮止め:SD-A051867-033にて本締め"
],
"WorkItems": [
... | [
{
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ取付②",
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ真直度・平行度調整",
"Words": [
"+0.025±0.005",
"反基準側(下段)",
"ｸﾞﾘｰｽ塗布 小豆:各5",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. 反基準側ﾚｰﾙ(下段)の真直度･平行度を調整する",
"1. 基準側ﾚｰﾙ(上段)の真直度を調整する",
"◆3. 基準面にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾋﾟｯ... | [
{
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ真直度・平行度調整",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "定盤",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①にJOINT を取付ける"
],
"WorkPoints": [
"ﾘﾆｱｶﾞｲﾄﾞ右端で取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
... | [
{
"WorkName": "ｸﾞﾘｰｽｼﾞｮｲﾝﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付",
"Words": [
"PIN",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｶﾞｲﾄﾞの右端で取付ける事",
"②の取付け位置決めﾋﾟﾝとﾘﾆｱｶﾞｲﾄﾞｽﾗｲﾀﾞｰの当付け面に隙間が無き事(0.01㎜)確認後ﾋﾟﾝに黄色ﾏｰｶｰをする"
],
"Tolks": [
"締付... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ配線引き回し(可動子側)",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"可動子配線",
"可動子配線",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①の可動子ﾓｰﾀ配線を下記指示に従い固定する"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸの頭の位置",
"ｲﾝｼｭﾛ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ配線引き回し(可動子側)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "定盤",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Y・Z方向変位測定",
"Words": [
"真直度 0.03mm以下",
"両端で0㎜",
"両端で0㎜",
"69mm",
"測定範囲:(0.03mm以下)",
"②測定範囲",
"482.5mm",
"632.5mm",
"①測定範囲",
"測定範囲:(0.01mm以下)",
"③測定範囲",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. ﾍｯ... | [
{
"WorkName": "Y・Z方向変位測定",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "定盤",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｵｲﾙﾊﾟﾝ・ﾘﾆｱｽｹｰﾙの取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"2. ①に③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽｹｰﾙ検出面を清掃する事",
"PINの位置に注意して取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m",
"締付ﾄﾙ... | [
{
"WorkName": "ｵｲﾙﾊﾟﾝ・ﾘﾆｱｽｹｰﾙの取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞの取付・調整",
"Words": [
"FM",
"FM",
"FM",
"左端",
"中央",
"右端",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をWASHER BOLT で仮付めする",
"2. 隙間調整を行い､WASHER BOLT を本締めする"
],
"WorkPoints": [
"ｽｹｰﾙ隙間測定は右端･中央･左端で確... | [
{
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞの取付・調整",
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"XBEAM の上面を傷つけ無い事",
"両側の下2本だけを取付ける",
"両側の上2本はSD‐A051867‐047で取付ける",
"ﾈｼﾞ穴を合わせて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付",
"Words": [
"B312",
"B311",
"CMRR",
"CMFR",
"A",
"CMFR",
"8㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. CABLE のｺﾈｸﾀｰへLABEL のﾗﾍﾞﾙを貼付ける(下図参照の事)"
],
"WorkPoints": [
"ｺﾈｸﾀｰの広い側に貼付ける事",
"A矢視"... | [
{
"WorkName": "ｹｰﾌﾞﾙﾗﾍﾞﾙ貼付",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ(及び、OP:文字認識対応ｶﾒﾗﾕﾆｯﾄｹｰﾌﾞﾙ時含む)",
"Words": [
"45㎜",
"110㎜",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①とCABLE に指定の寸法の位置でﾏｰｷﾝｸﾞをする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"Wor... | [
{
"WorkName": "ｹｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ(及び、OP:文字認識対応ｶﾒﾗﾕﾆｯﾄｹｰﾌﾞﾙ時含む)",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回①",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作",
"A矢視",
"ｲﾝｼｭﾛｯｸの頭位置"
],
"WorkItems": [
"1. ①に②を下記指示の順番で㉗で固定する"
],
"WorkPoints": [
"束ね方向と位置に注意する事",
"ｽﾄｯﾊﾟｰより配... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回①",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回②",
"Words": [
"ｲﾝｼｭﾛｯｸの頭位置",
"ｲﾝｼｭﾛｯｸの頭位置",
"ｲﾝｼｭﾛｯｸを通しておく",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. TUBE TUBE を①のｼﾞｮｲﾝﾄに挿入する",
"2. 2完成品を㉖で固定する",
... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回②",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回③",
"Words": [],
"WorkItems": [
"2. 1完成品にTUBE を差込む",
"1. ①に②③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"矢印の方向に当付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],
"InspectionN... | [
{
"WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ部配線引き回③",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ取付",
"Words": [
"2度繰り返す",
"この作業では同じものを2個製作",
"ｲﾝｼｭﾛｯｸ指示",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"4. ｲﾝｼｭﾛｯｸで固定する",
"3. ﾄﾞﾛｱｺﾈｸﾀｰの位置調整を行う",
"2. 治具(FM-5782)を取付ける",
"1. ①に②をBOLT で仮付ける"
],
"WorkPoints": [
... | [
{
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-5782",
"ToolName": "ﾍｯﾄﾞﾄﾞﾛﾜ位置決め治具(設備側)",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付➀",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"3. ①に②を③⑯⑰⑲で取付ける",
"4. 3完成品に④を⑯⑱で取付ける",
"2. ①の仮止めされているﾏｳﾝﾄを角度を調整し本締めする",
"1. １完成品に⑳㉑を取付ける"
],
"WorkPoints": [
"②取付の際に②とBEAMが平行るように取付ける",
"②と④の間に隙間が無い事"... | [
{
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付➀",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": ... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付②",
"Words": [
"この作業では同じものを2個製作",
"⑰ ｺﾞﾏ粒:2粒",
"⑲ ｺﾞﾏ粒:3粒",
"ﾈｼﾞ山脱脂した後､ﾛｯｸﾀｲﾄ塗布の事"
],
"WorkItems": [
"2. ①に②をSPACER WASHER BOLT BOLT (ﾛｯｸﾀｲﾄ塗布済)で取付ける",
"3. 2完成品にBRACKET をWASHER BOLT で取付ける",
"1. BOLT にWASHER をセ... | [
{
"WorkName": "Ⅹ軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付②",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"-"
]
},... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②③をBOLT WASHER で取付ける",
"2. 1完成品の仮締めの板金を位置調整する"
],
"WorkPoints": [
"矢印方向に当てつけて取付ける",
"ﾋﾞｰﾑと隙間なく面で接している事",
"〇のBOLT WASHER のみ仮締めする事",
"②③はF側とR側で異なるので注... | [
{
"WorkName": "Y軸ﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾏｸﾞﾈｯﾄ取付①",
"Words": [
"Ser.No※※※※※",
"ﾏｸﾞﾈｯﾄ吸着部",
"この作業では同じものを2個製作"
],
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.の確認を行う",
"■◆2. ①の右側にMOTOR をBOLT で取付ける",
"■◆3. ２完成品にマグネット付属品と㉘を取付ける"
],
"WorkPoints": [
"ﾏｸﾞﾈｯﾄ吸着部に金属類を近づけ... | [
{
"WorkName": "ﾏｸﾞﾈｯﾄ取付①",
"QualityItem": "型式確認･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C09",
"Others": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ﾏｸﾞﾈｯﾄ取付②",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"■◆1. ①にMOTOR をBOLT で取付ける",
"■◆2. 固定子･可動子間の隙間確認後､固定子安全ｶﾊﾞｰ･半ｶﾊﾞｰを取付ける"
],
"WorkPoints": [
"Ser.No.LABEL",
"Ser.No.LABELを下面右側にして取付ける事",
"固定しの磁力に注意しながら作業する事"
],
... | [
{
"WorkName": "ﾏｸﾞﾈｯﾄ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "ｽﾄｯﾊﾟｰ・ﾊﾝﾄﾞﾙ取付",
"Words": [
"この作業では同じものを2個製作"
],
"WorkItems": [
"1. ①に②を取付ける",
"2. ①にHANDLE BRACKET をBOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"目視で真っすぐに取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 194cN･m",
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ・ﾊﾝﾄﾞﾙ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：X軸（001-",
"WorkName": "干渉ｾﾝｻｰ(Rのみ)取付",
"Words": [],
"WorkItems": [
"1. ①にCLIP BOLT ､SENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"R側のみに取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
... | [
{
"WorkName": "干渉ｾﾝｻｰ(Rのみ)取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&トレイ)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&ﾄﾚｲ)1",
"Words": [],
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&ﾄﾚｲ)1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proce... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&トレイ)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&ﾄﾚｲ)2",
"Words": [
"仮止め:SD-EJM2FH1-276にて本締め"
],
"WorkItems": [
"1. ①にCOVER をBOLT WASHER BOLT で取付ける",
"2. 1完成品にBRACKET をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [
... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&ﾄﾚｲ)2",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proce... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&トレイ)NPM-GW専用（001-",
"WorkName": "ｽﾙｰ部品17連/34連(後側&右側&ﾄﾚｲ)",
"Words": [],
"WorkItems": [
"1. H1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [],
"Jigus": [... | [
{
"WorkName": "ｽﾙｰ部品17連/34連(後側&右側&ﾄﾚｲ)",
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(前側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&台車)1",
"Words": [],
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [],... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&台車)1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proces... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(前側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&台車)2",
"Words": [
"仮止め:SD-EJM2FH1-276にて本締め"
],
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付ける",
"2. 1完成品にBRACKET をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ ... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&台車)2",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proces... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(前側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｽﾙｰ部品17連/34連(前側&右側&台車)",
"Words": [],
"WorkItems": [
"1. H1工程へ払い出す"
],
"WorkPoints": [
"PLATE のﾌﾟﾚｰﾄは交換台車駆動部で組付けします｡(払い出しません)"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkType... | [
{
"WorkName": "ｽﾙｰ部品17連/34連(前側&右側&台車)",
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&台車)1",
"Words": [
"仮止め:SD-A051898-002にて本締め"
],
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける",
"2. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で仮に取付ける"
],
"WorkPo... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&台車)1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proces... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&台車)2",
"Words": [],
"WorkItems": [
"2. 1完成品にCOVER をBOLT WASHER で取付ける",
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"面位置に取付の事",
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(後側&右側&台車)2",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proce... | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(後側&右側&台車)NPM-GW専用（001-",
"WorkName": "ｽﾙｰ部品17連/34連(後側&右側&台車)",
"Words": [],
"WorkItems": [
"1. H1へ払い出す"
],
"WorkPoints": [
"PLATE のﾌﾟﾚｰﾄは交換台車駆動部で組付けします｡(払い出しません)"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes"... | [
{
"WorkName": "ｽﾙｰ部品17連/34連(後側&右側&台車)",
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-GW ：ITF17連ASF34連交換台車駆動部(前側＆右側＆トレイ)NPM-GW専用（001-",
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&ﾄﾚｲ)1",
"Words": [],
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionItems": [... | [
{
"WorkName": "ｶﾞｲﾄﾞ部組立17連/34連(前側&右側&ﾄﾚｲ)1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"Proce... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.