command stringlengths 2 75 | syntax stringlengths 0 289k | hierarchy_level stringlengths 0 6.91k | description stringlengths 0 45.2k | options listlengths 0 499 | required_privilege_level stringlengths 0 330k | release_information stringlengths 0 3.14k | related_documentation listlengths 0 22 |
|---|---|---|---|---|---|---|---|
request server authenticate-peer-server | request server authenticate-peer-server | Copy the ssh public key to the peer JDM. This command is equivalent to ssh-copy-id user@jdm-server<0/1>.
NOTE: If the JDM fails to establish SSH connection with its peer on either of the two CB
links, you need to run the JDM CLI command request server authenticate-peer-server. You
can use the JDM CLI command show serve... | [] | View
Sample Output
command-name
user@jdm> request server authenticate-peer-server
/usr/bin/ssh-copy-id: INFO: attempting to log in with the new key(s), to filter out anythat are
already installed
/usr/bin/ssh-copy-id: INFO: 1 key(s) remain to be installed -- if you are prompted now it is to
install the new keys
user@... | Command introduced in Junos OS Release 17.4R1. | [
"Generic Guidelines for Using JDM Server Commands"
] | |
request services advanced-anti-malware data-connection | request services advanced-anti-malware data-connection test (start <0-32768> | status) | Test not started.
You cannot view the status without first running the data connection test. Run the request
services advanced-anti-malware data-connection test start CLI command and then check the
status again.
Test in progress.
The data connection test has not finished. Wait a few seconds and try the command again.
D... | [
{
"name": "start <0-32768>",
"desc": "Start the data connection test and specify the packet payload size in bytes."
},
{
"name": "status",
"desc": "Returns the result of the data connection test. See Table 140 on page 15452."
}
] | View
Output Fields
This CLI command returns a single line that indicates the data connection results. Table 140 on page
15452 lists the possible results.
Table 140: Data Connection Test Output
Message | Command introduced in Junos OS Release 15.1X49-D60. | [] | |
request services advanced-anti-malware diagnostic | request services advanced-anti-malware diagnostic url (detail | pre-detection url | routing-
instance instance-name) | SSL profile ssl profile name is empty.
The SSL profile has neither trusted CA nor client certificate
configured.
SSL local certificate local certificate is
inconsistent between PFE and RE.
The SSL client certificate does not exist in PFE.
SSL CA ca name is inconsistent between
PFE and RE.
The SSL CA exists in the RE bu... | [
{
"name": "url",
"desc": "URL to the Juniper Advanced Threat Prevention Cloud server."
},
{
"name": "detail",
"desc": "(optional) Debug mode that provides more verbose output."
},
{
"name": "pre-detection",
"desc": ""
},
{
"name": "url",
"desc": "(optional) Pre-detection ... | View
Sample Output
request services advanced-anti-malware diagnostic
user@host> request services advanced-anti-malware diagnostic abc.def.junipersecurity.net
Time check : [OK]
DNS check : [OK]
SKYATP reachability check ... | Command introduced in Junos OS Release 15.1X49-D60. The interface name to cloud check, MTU
warning, and client and server clock check added in Junos OS Release 15.1X49-D90. routing-instance
option added in Junos OS Release 15.1X49-D100. | [] | |
request services advanced-anti-malware redirect-file | request services advanced-anti-malware redirect-file
<add|delete ></var/tmp/custom_page.html>
Note that the file path is required when adding a file. When deleting a file, only the file name, no path, is
required. For example: request services advanced-anti-malware redirect-file delete custom_page.html | Allows you to add a customized file for users to be directed to. The file must be no larger than 8KB.
A default rich html file named “aamw_default_page.html” is included on the SRX Series Firewall for you
to use. It says the following:
THIS SITE HAS BEEN BLOCKED
Sorry, the page you are looking for has been blocked due ... | [
{
"name": "add",
"desc": "Add a redirect file"
},
{
"name": "delete",
"desc": "Delete a redirect file Additional Information See \"advanced-anti-malware policy\" on page 2172 for the set services advanced-anti-malware policy p1 http client-notify file command."
}
] | View | Command introduced in Junos OS Release 19.3R1. | [] | |
request services anti-virus machine-learning-engine | request services anti-virus machine-learning-engine start
request services anti-virus machine-learning-engine stop
request services anti-virus machine-learning-engine status | Run these commands to enable and disable machine learning (ML)-based zero-day threat detection. | [
{
"name": "start",
"desc": "Enable ML-based threat detection."
},
{
"name": "stop",
"desc": "Disable ML-based threat detection."
},
{
"name": "status",
"desc": "Check the status of ML-based threat detection."
}
] | View
Sample Output
request services anti-virus machine-learning-engine start
request services anti-virus machine-learning-engine start
request services anti-virus machine-learning-engine status
request services anti-virus machine-learning-engine status
Active (enabled)
request services anti-virus machine-learning-engin... | Command introduced in Junos OS Release 24.2R1. | [] | |
request services anti-virus update | request services anti-virus update
request services anti-virus update status
request services anti-virus update-check-server | No AV license detected or license is expired
Specifies that either Juniper AV license is not installed or
the license has expired.
Anti-virus update is in progress
Specifies that the antivirus update is in progress.
Virus DB version
Specifies the antivirus database version.
Virus DB total count
Total number of antiviru... | [
{
"name": "status",
"desc": "Check the download status of antivirus database."
},
{
"name": "update-check-server",
"desc": "Check the connection status with the CDN server, from which you download the antivirus database package. Additional Information See \"anti-virus (Services)\" on page 2460 t... | View
Output Fields
This CLI command returns a single line that indicates the status of antivirus update. Table 143 on page
15463 lists the possible results.
Table 143: Antivirus Update Output Fields
Message | Command introduced in Junos OS Release 23.4R1.
request services application identification install ignore duplicate version | [] | |
check | request services application-identification install ignore-duplicate-version-check | Forcefully installs the application signature package over the same version of the signature package. | [] | maintenance
Sample Output
When you enter this command, the system provides feedback on the status of your request.
request services application-identification install ignore-duplicate-version-check
user@host> request services application-identification install ignore-duplicate-version-check
Please use command
... | Command introduced in Junos OS Release 21.1R1. | [
"Predefined Application Signatures for Application Identification"
] | |
request services application identification new to production | request services application-identification new-to-production [applications-list
application-name | all]] | Migrate the applications tagged as new in the installed application signature pack on your security
device to normal applications.
The applications tagged as new are part of junos:all-new-apps group. Once you migrate the new
applications to normal applications, these applications will no longer be tagged as new and wil... | [
{
"name": "applications-list",
"desc": "Specify list of applications to migrate to normal applications."
},
{
"name": "all",
"desc": "Migrate all new applications as normal applications"
}
] | view
Sample Output
request services application-identification new-to -production application-list
user@host> request services application-identification new-to-production applications-list
[junos:RLOGIN junos:LINKEDIN]
Please wait while we are updating signatures ...
new-to-production command successfully executed
r... | Command introduced in Junos OS Release 21.1R1. | [
"Predefined Application Signatures for Application Identification"
] | |
request services application-identification application | request services application-identification application [disable | enable] predefined-
application-name | Disable, or enable a predefined application signature. | [
{
"name": "predefined-application-name",
"desc": "Application name; a maximum of up to 31 characters. Predefined applications"
},
{
"name": "disable",
"desc": "(Optional) Disable a predefined application signature, initiate signature recompilation, and"
},
{
"name": "enable",
"desc":... | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
request services application-identification application disable
user@host> request services application-identification application disable junos:163
Please wait while we are updating signat... | Command introduced in Junos OS Release 11.4. | [] | |
request services application-identification clear packet-capture all | request services application-identification clear packet-capture all | Clear all packet capture files generated for unknown application traffic. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
command-name
user@host> request services application-identification clear packet-capture all
Packet-capture file(s) deleted | Statement introduced in Junos OS Release 20.2R1. | [
"Configure Packet Capture For Unknown Application Traffic"
] | |
request services application-identification download status | request services application-identification download status | Check the download status of the application signature package. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request. The output
displays the application package version.
Sample Output
request services application-identification download status
user@host> request services application-identifications download status ... | Statement introduced in Junos OS Release 10.2. | [] | |
request services application-identification download | request services application-identification download
<check-server>
<minor-only>
<status>
<version> | Manually download the application signature package for Junos OS application identification.
Juniper Networks regularly updates the predefined application signature package database and makes it
available to subscribers on the Juniper Networks website.
When you enter the command, the system retrieves the application pa... | [
{
"name": "check-server",
"desc": "Retrieve the latest application signature package details available from the sigpack"
},
{
"name": "minor-only",
"desc": "Download the minor type of application package. If you do not specify this option, the"
},
{
"name": "status",
"desc": "Check t... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services application-identification download
user@host> request services application-identifications download
Please use command "request services application-identification... | Statement introduced in Junos OS Release 10.2. | [] | |
request services application-identification group | request services application-identification group [copy | disable | enable] predefined-
application-group-name | Copy, disable, or enable a predefined application signature group. | [
{
"name": "copy",
"desc": "(Optional) Copy a predefined application signature group from the database to the configuration and change the name (for example, my:FTP). The ID and order are generated automatically. Do not name your custom application signature group with the junos prefix; this prefix is reserv... | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
request services application-identification group
user@host> request services application-identification group disable
junos:infrastructure:networking
Disable application group ... | Command introduced in Junos OS Release 11.4. | [] | |
request services application-identification install status | request services application-identification install status | Display the status of the install operation. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
request services application-identification install status
user@host> request services application-identification install status
Installed Application package (3702) and Protoco... | Statement introduced in Junos OS Release 11.4. | [] | |
request services application-identification install | request services application-identification install | Install the downloaded predefined application signature package. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
command-name
user@host> request services application-identification install
Please use command "request services application-identification install status" to check status
and ... | Statement introduced in Junos OS Release 11.4. | [
"request services application-identification offline-download package-"
] | |
path | request services application-identification offline-download package-path <path> | Extract the application signature package from a downloaded local tar file.
When you enter this command, the system untars the signature package and places the extracted files in
the proper locations on the device. | [] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services application-identification offline-download package-path
user@host> request services application-identification offline-download package-path /root/appid-
offline-update.tar-2.g... | Statement introduced in Junos OS Release 24.4R1. | [
"request services application-identification download status",
"request services application-identification install"
] | |
request services application-identification proto-bundle-status | request services application-identification proto-bundle-status | Display the status of the install operation of the protocol bundle. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
command-name
user@host> request services application-identification proto-bundle-status
Protocol Bundle Version (1.30.4-22.005 (build date Jan 17 2014)) and application secpack ... | Statement introduced in Junos OS Release 12.1X47-D10. | [] | |
request services application-identification rollback status | request services application-identification rollback status | Displays the status of the application signature package rollback.
You can use this command when you manually rollback the application signature package to the
previously installed version using the request services application-identification rollback command. | [] | maintenance
Output Fields
This command provides the application signature package rollback status.
Sample Output
request services application-identification rollback status
user@host> request services application-identification rollback status
Sample: When rollback is successful.
Application package (3250) and Protoco... | Command introduced in Junos OS Release 20.3R1. | [] | |
request services application-identification uninstall status | request services application-identification uninstall status | Display the status of the uninstall operation. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
command-name
user@host> request services application-identification uninstall status
Uninstall application package version (1776) succeed. | Statement introduced in Junos OS Release 11.4. | [] | |
request services application-identification uninstall | request services application-identification uninstall | Uninstall the predefined application package.
The uninstall operation will fail if any active security policies reference predefined application signatures
or predefined application signature groups in the Junos OS configuration. | [] | maintenance
Output Fields
When you enter this command, the system provides feedback on the status of your request.
Sample Output
command-name
user@host> request services application-identification uninstall
Please use command "request services application-identification uninstall status" to check
status ... | Statement introduced in Junos OS Release 10.2. Statement modified in Junos OS Release 10.4.
Statement modified in Junos OS Release 11.4. | [] | |
request services extensible-subscriber-services reload-dictionary | request services extensible-subscriber-services reload-dictionary | Reload the configured dictionary to essmd. | [] | system—To view this statement in the configuration.
system-control—To add this statement to the configuration.
Sample Output
command-name
# request services extensible-subscriber-services reload-dictionary
Dictionary reloaded successfully | Command introduced in Junos OS Release 15.1. | [
"Understanding the Dictionary File"
] | |
request services flow-collector change-destination primary interface | request services flow-collector change-destination primary interface cp-fpc/pic/port
<clear-files>
<clear-logs>
<immediately | gracefully> | (M40e, M160, and M320 Series routers and T Series routers only) Switch to the primary File Transfer
Protocol (FTP) server that is configured as a flow collector. | [
{
"name": "none",
"desc": "Switch to the primary FTP server."
},
{
"name": "cp-fpc/pic/port",
"desc": "Use the specified flow collector interface name for the primary destination."
},
{
"name": "clear-files",
"desc": "(Optional) Request clearing of existing data files in the FTP wait... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services flow-collector change-destination primary interface
user@host> request services flow-collector change-destination primary interface
cp-6/0/0
Flow collector interfa... | Command introduced before Junos OS Release 7.4. | [] | |
request services flow-collector change-destination secondary interface | request services flow-collector change-destination secondary interface cp-fpc/pic/
port
<clear-files>
<clear-logs>
<immediately | gracefully> | (M40e, M160, and M320 Series routers and T Series routers only) Switch to the secondary File Transfer
Protocol (FTP) server that is configured as a flow collector. | [
{
"name": "none",
"desc": "Switch to the secondary FTP server."
},
{
"name": "cp-fpc/pic/port",
"desc": "Use the specified flow collector interface name (cp-fpc/pic/port) for the secondary destination."
},
{
"name": "clear-files",
"desc": "(Optional) Request clearing of existing data... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services flow-collector change-destination secondary interface
user@host> request services flow-collector change-destination secondary interface
cp-6/0/0
Flow collector in... | Command introduced before Junos OS Release 7.4. | [] | |
request services flow-collector test-file-transfer | request services flow-collector test-file-transfer filename interface (all | cp-fpc/pic/port)
(channel-zero | channel-one) (primary | secondary) | (M40e, M160, and M320 Series routers, PTX Series, and T Series routers only) Transfer a test file to the
primary or secondary File Transfer Protocol (FTP) server that is configured as a flow collector. This
command verifies that the output side of the flow collector interface is operating properly. | [
{
"name": "filename",
"desc": "Name of the test file to transfer."
},
{
"name": "interface (all | cp-fpc/pic/",
"desc": ""
},
{
"name": "port)",
"desc": "Transfer a test file of flows from all configured flow collector interfaces or from only the specified interface."
},
{
"n... | network
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services flow-collector test-file-transfer interface channel-one primary
user@host> request services flow-collector test-file-transfer test_file interface cp-7/1/0
channel-one primary
Flow... | Command introduced before Junos OS Release 7.4. | [] | |
request services ip-monitoring preempt-restore policy | request services ip-monitoring preempt-restore policy
<policy-name> | If the no–preempt option is specified, the policy will not perform preemptive failback when it is in a
failover state, and when the RPM probe test recovers from failure. To manually revert to the failback
state, run the request services ip-monitoring preempt-restore policy command.
NOTE: The request services ip-monito... | [
{
"name": "policy name",
"desc": "Name of the policy."
}
] | maintenance
Output Fields
When you run this command, the policy is restored to the failback state.
Sample Output
run request services ip-monitoring preempt-restore policy <policy name>
user@host> run request services ip-monitoring preempt-restore policy policy1
Restore request succeeded: Policy policy1 | Command introduced in Junos OS Release 11.4. | [] | |
request services ipsec-vpn ipsec switch tunnel | request services ipsec-vpn ipsec switch tunnel local-gateway address remote-gateway
address
<routing-instance instance-name> | (Adaptive services interface only) Manually switch between primary and backup IP Security (IPsec)
tunnels. | [
{
"name": "local-gateway address",
"desc": "Gateway address of the local system."
},
{
"name": "remote-gateway address",
"desc": "Gateway address of the remote system."
},
{
"name": "routing-instance instance-name",
"desc": "(Optional) VRF instance associated with local gateway addre... | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services ipsec-vpn ipsec switch tunnel
user@host> request services ipsec-vpn ipsec switch tunnel local-gateway 10.1.1.1 remote gateway
10.100.10.1 | Command introduced before Junos OS Release 7.4.
routing-instance option added in Release 8.1. | [] | |
request services l2tp destination unlock | request services l2tp destination unlock destination-name | Remove the specified destination from the destination lockout list immediately, before its lockout period
expires. As a result, the L2TP process can again consider the destination during the selection of new
tunnels. | [
{
"name": "destination-name",
"desc": "Name of the destination to be unlocked."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services l2tp destination unlock
user@host> request services l2tp destination unlock dest-a
Destination dest-a unlocked | Command introduced in Junos OS Release 13.2. | [
"L2TP Tunnel Switching For Multiple-Domain Networks",
"L2TP Tunnel Switching For Multiple-Domain Networks"
] | |
request services monitoring twamp client | request services monitoring twamp client (start | stop)
<control-connection-name>
repeat <number> | Start or stop a Two-Way Active Measurement Protocol (TWAMP) session. You can start or stop all of the
sessions for all of the TWAMP clients, or start or stop a session for a specific TWAMP client control
connection. When you start all the test sessions configured for a particular TWAMP client, the control-
client start... | [
{
"name": "control-connection-name",
"desc": "(Optional) Start or stop the TWAMP session with the server for only the specified control-connection or TWAMP control-client. If you do not specify this option, all control connections are either started or stopped."
},
{
"name": "repeat number",
"de... | view | Command introduced in Junos OS Evolved 20.3R1. | [
"Understanding Two-Way Active Measurement Protocol on Routers"
] | |
request services paa install | request services paa install
cc-account account
cc-host host
cc-user user@domain
cc-password password
ta-version version
ta-name name
cc-port port
<cc-insecure>
<ta-debug> | Install the Paragon Active Assurance (PAA) test agent. Junos OS Evolved Release 22.3R1 supports
installing test agents for PAA 4.0 and later. This command fetches the PAA test agent software image
from the PAA Control Center for you and installs the software into a Docker container.
Before issuing this command, make su... | [
{
"name": "cc-account",
"desc": ""
},
{
"name": "account",
"desc": "(Required) Your PAA Control Center user account."
},
{
"name": "cc-host host",
"desc": "(Required) IP address or DNS host name of the PAA Control Center."
},
{
"name": "cc-user",
"desc": ""
},
{
"... | maintenance
Sample Output
request services paa install (first-time installation)
user@host> request services paa install cc-account my_account cc-host host cc-user user@domain
cc-password $1234abc ta-version 4.0.0.29 ta-name my_test_agent cc-port 6800
PAA installation files copied from 10.83.153.119.
Starting docker d... | Command introduced in Junos OS Evolved Release 22.3R1.
Command deprecated in Junos OS Evolved Release 23.4R1. Replaced by the test-agent configuration
statement at the [edit services paa] hierarchy level. | [
"Install the Paragon Active Assurance (PAA) Test Agent"
] | |
request services paa uninstall | request services paa uninstall | Uninstall the Paragon Active Assurance (PAA) test agent. Before installing a different version of the test
agent software, you must uninstall the previous test agent software.
Additional Information
You can also use NETCONF to uninstall the PAA test agent:
<rpc>
<uninstall-paa-ta>
</uninstall-paa-ta>
</... | [] | maintenance
Sample Output
request services paa uninstall
user@host> request services paa uninstall
Stopping PAA test agent.
Done. Un-installation of PAA test agent. | Command introduced in Junos OS Evolved Release 22.3R1.
Command deprecated in Junos OS Evolved Releases 23.4R1. Replaced by deleting the test-agent
configuration statement at the [edit services paa] hierarchy level. | [
"Install the Paragon Active Assurance (PAA) Test Agent"
] | |
request services redundancy-set trigger | request services redundancy-set (redundancy-set |all) trigger redundancy-event | Manually trigger a redundancy event for the specified redundancy set or all sets on the current gateway. | [] | view | Statement introduced in Junos OS Release 16.1. | [] | |
request services remote-device-management reconfigure service-device | request services remote-device-management reconfigure service-device device-name | Reconfigure a remote device to provision all active subscriber services matching the access domain (list
of VLAN ranges and IDs) configured for this remote device with the vlan-id-list option at the [[edit
system services remote-device-management service-device device-nameaccess-domain] hierarchy level. | [
{
"name": "device-name",
"desc": "System-wide name of the remote device that uniquely identifies the device across routing instances."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services remote-device-management reconfigure service-device (Successful)
user@host> request services remote-device-management reconfigure service-device OLT1
succeeded
request services remote... | Command introduced in Junos OS Release 18.3R1. | [
"Reconfiguring a Remote Device for RDSM",
"Remote Device Services Manager (RDSM) Overview"
] | |
request services remote-device-management reload-dictionary | request services remote-device-management reload-dictionary absolute file path | Reload the specified dictionary to the RDSM database. The dictionary is configured with the dictionary
option at the [edit system services remote-device-management service-devicedevice-name] hierarchy level. The
reload affects all remote service devices that are configured with this dictionary. When you modify an
exist... | [
{
"name": "absolute file",
"desc": ""
},
{
"name": "path",
"desc": "Absolute file path for the vendor-specific dictionary that defines the set of NETCONF XML protocol commands required to provision, deprovision, and roll back a subscriber service on the remote device. The dictionary is stored on... | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services remote-device-management reload-dictionary (Successful)
user@host> request services remote-device-management reload-dictionary /var/home/dict/vendor-1-
dictionary.xml
Dictionary reloa... | Command introduced in Junos OS Release 18.3R1. | [
"Reloading a Dictionary File for RDSM",
"Remote Device Services Manager (RDSM) Overview"
] | |
request services rpm twamp | request services rpm twamp (start | stop) client <control-connection-name> | Start or stop a TWAMP session. You can start or stop all of the sessions for all of the TWAMP clients, or
start or stop a session for a specific TWAMP client. When you start all the test session configured for a
particular TWAMP client, the control-client initiates all requested testing with a Start-Sessions message,
a... | [
{
"name": "start client",
"desc": "Start the TWAMP session between the TWAMP client and the TWAMP server."
},
{
"name": "stop client",
"desc": "Terminate the TWAMP session between the TWAMP client and the TWAMP server."
},
{
"name": "control-connection-name",
"desc": "(Optional) Star... | view
Output Fields
When you enter this command, you are not provided feedback on the status of your request.
Sample Output
request services rpm twamp start client
user@host> request services rpm twamp start client c1 | Command introduced in Junos OS Release 15.1. | [] | |
request services static-subscribers login group | request services static-subscribers login group group-name | Resets the state of an interface group on which static subscribers were forcibly logged out by the request
services static-subscribers logout group command. This action enables static subscriber to login on the
interfaces in the group. | [
{
"name": "group group-name",
"desc": "Group of static subscriber interfaces on which static subscribers have been created."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services static-subscribers login group
user@host> request services static-subscribers login group boston | Command introduced in Junos OS Release 9.6. | [
"Monitoring and Managing Static Subscriber Information"
] | |
request services static-subscribers login interface | request services static-subscribers login interface interface-name | Resets the state of an interface on which a static subscriber was forcibly logged out by the request
services static-subscribers logout interface command. This action enables a static subscriber to login on
the interface. | [
{
"name": "interface interface-name",
"desc": "Static interface on which a static subscriber has been created."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services static-subscribers login interface
user@host> request services static-subscribers login interface ge-2/0/1.5 | Command introduced in Junos OS Release 9.6. | [
"Monitoring and Managing Static Subscriber Information"
] | |
request services static-subscribers logout group | request services static-subscribers logout group igroup-name | Force static subscribers on the interfaces in the group to be logged out. No subscriber can subsequently
log in on the interface group until the interface state is reset by a router reset or the request services
static-subscribers login group command. | [
{
"name": "group group-name",
"desc": "Group of static subscriber interfaces on which static subscribers have been created."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services static-subscribers logout group
user@host> request services static-subscribers logout group boston | Command introduced in Junos OS Release 9.6. | [
"Monitoring and Managing Static Subscriber Information"
] | |
request services static-subscribers logout interface | request services static-subscribers logout interface interface-name | Force static subscriber on the interface to be logged out. No subscriber can subsequently log in on the
interface until the interface state is reset by a router reset or the request services static-subscribers login
interface command. | [
{
"name": "interface interface-name",
"desc": "Static interface on which a static subscriber has been created."
}
] | view
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request services static-subscribers logout interface
user@host> request services static-subscribers logout interface ge-2/0/1.5 | Command introduced in Junos OS Release 9.6. | [
"Monitoring and Managing Static Subscriber Information"
] | |
request services subscribers clear | request services subscribers clear subscriber-profile profile client-id client-id | Clear the subscriber profile associated with the given subscriber. | [
{
"name": "profile",
"desc": "Name of the subscriber profile to clear the active subscriber profile for the given subscriber."
},
{
"name": "client-id",
"desc": "Client session ID assigned to the subscriber."
}
] | clear
Sample Output
request services subscriber clear subscriber-profile tc_act_prof client-id
user@host>request services subscriber clear subscriber-profile tc_act_prof client-id
2533274790395909 | display xml
rpc-reply xmlns:junos="http://xml.juniper.net/junos/11.1I0/junos"
packet-triggered-subscribers-informati... | Command introduced in Junos OS Release 11.4. | [] | |
request services subscribers | request services subscribers set subscriber-profile profile client-id client-id | Set the subscriber profile associated with the given subscriber. | [
{
"name": "profile",
"desc": "Name of the subscriber profile to create or override the currently active subscriber profile for the given subscriber."
},
{
"name": "client-id",
"desc": "Client session ID assigned to the subscriber."
}
] | view
Sample Output
request services subscriber set subscriber-profile tc_act_prof client-id
user@host> request services subscriber set subscriber-profile tc_act_prof client-id
2533274790395909 | display xml
rpc-reply xmlns:junos="http://xml.juniper.net/junos/11.1I0/junos"
packet-triggered-subscribers-information x... | Command introduced in Junos OS Release 11.4. | [] | |
request services url-filter delete gencfg-data | request services url-filter delete gencfg-data | Delete url-filterd–ased objects. This is historical information.
WARNING: Do not use this command unless explicitly instructed to do so.
NOTE: Starting in Junos OS Release 18.3R1, the request services url-filter delete gencfg-
data command is deprecated and has been replaced by the request services web-filter
delete ge... | [] | view | Command introduced in Junos OS Release 17.2. | [
"Configuring URL Filtering"
] | |
request services url-filter force dns-resolution | request services url-filter force dns-resolution (all | profile profile-name)
<template template-name> | Force the domain name system (DNS) resolution request.
NOTE: Starting in Junos OS Release 18.3R1, the request services url-filter force dns-
resolution command is deprecated and has been replaced by the request services web-filter
force dns-resolution command. | [
{
"name": "all",
"desc": "Force a DNS resolution request for all profiles."
},
{
"name": "profile profile-name",
"desc": "Force a DNS resolution request for the profile (all templates)."
},
{
"name": "template template-name",
"desc": "Force a DNS resolution request for the template."... | view
Sample Output
request services url-filter force dns-resolution profile profile1
user@host> request services url-filter force dns-resolution profile profile1
STATUS: DNS resolution is triggered for profile profile1
request services url-filter force dns-resolution profile profile1 template template1
user@host> requ... | Command introduced in Junos OS Release 17.2. | [
"Configuring URL Filtering"
] | |
request services url-filter update url-filter-database file | request services url-filter update url-filter-database file filename | Update the URL filter database. If you change the database file, run this command. It sends a request to
the DNS server for only the new hostnames that were not in the previous version of URL database file.
NOTE: Starting in Junos OS Release 18.3R1, the request services url-filter update url-
filter-database file comma... | [
{
"name": "filename",
"desc": "Use the database filename."
}
] | view | Command introduced in Junos OS Release 17.2. | [
"Configuring URL Filtering"
] | |
request services url-filter validate | request services url-filter validate (all | file-name filename) | Validate the URL filter database to ensure the database is correct.
NOTE: Starting in Junos OS Release 18.3R1, the request services url-filter validate
command is deprecated and has been replaced by the request services web-filter validate
url-filter-file-name command. | [
{
"name": "all",
"desc": "Validate the URL filter database for all profiles."
},
{
"name": "file-name filename",
"desc": "Validate the URL filter database for the database file specified."
}
] | view | Command introduced in Junos OS Release 17.2. | [
"Configuring URL Filtering",
"request services user-identification active-directory-access active-"
] | |
directory-authentication-table delete | request services user-identification active-directory-access active-directory-authentication-
table delete
(domain name | ip-address ip-address | group group-name <domain name> | user name <domain name> | Delete entries from the active directory authentication table by domain, address, group, or user. This
command provides the network administrator with flexibility and control over the table entries beyond
what is automatically added to or deleted from the table. For example, if a person leaves the company,
the correspo... | [
{
"name": "domain name",
"desc": "Delete the entries from the authentication table for the specified domain."
},
{
"name": "ip-address ip-address",
"desc": "Delete the entry from the authentication table for the specified IP address."
},
{
"name": "group group-name",
"desc": "Delete ... | maintenance
Output Fields
This command produces no output. | Command introduced in Junos OS Release 12.1X47-D10. | [
"show services user-identification active-directory-access active-directory-authentication-table",
"Understanding Active Directory Authentication Tables",
"request services user-identification active-directory-access domain-"
] | |
controller | request services user-identification active-directory-access domain-controller discovery
domain name | Discover and display the name and address of all domain controllers in the specified domain. | [
{
"name": "domain name",
"desc": "Name of the domain for which to get and display domain controller names and"
}
] | maintenance
Output Fields
This command displays the discovered domain controllers.
Sample Output
request services user-identification active-directory-access domain-controller discovery
domain <domain-name>
user@host> request services user-identification active-directory-access domain-controller
discovery domain examp... | Command introduced in Junos OS Release 12.1X47-D10. | [] | |
request services user-identification active-directory-access ip-user-probe | request services user-identification active-directory-access ip-user-probe
address ip-address <domain name> | Probe the PC at the specified IP address to get an authentication entry, which is used for the integrated
user firewall feature. You can display the authentication table to see the results. If the probe succeeded,
there will be a valid authentication entry. If the probe failed, there will be an invalid authentication e... | [
{
"name": "address ip-address",
"desc": "Probe the PC at this IP address."
},
{
"name": "domain name",
"desc": "Probe the IP address in the specified domain."
}
] | maintenance
Output Fields
The following command displays the results of the IP address probe:
Sample Output
show services user-identification active-directory-access active-directory-authentication-
table address <ip-address>
user@host> show services user-identification active-directory-access active-directory-
authen... | Command introduced in Junos OS Release 12.1X47-D10. | [
"show services user-identification active-directory-access active-directory-authentication-table",
"request services user-identification authentication-source aruba-"
] | |
clearpass user-query | request services user-identification authentication-source authentication-source user-query
address ip-address | Manually send to the ClearPass website a request for user authentication and identity information for
an individual user. The command specifies the IP address of the user’s device to identify the user whose
information you want to obtain. If the user query command executes successfully, an entry for the user
(IP addres... | [
{
"name": "ip-address",
"desc": "The IP address of the user’s device for whom you are manually requesting authentication information. NOTE: Starting with Junos OS Release 15.1X49-D130, SRX Series Firewall can query ClearPass for IPv6 addresses, in addition to IPv4 addresses for an individual user."
}
] | maintenance
Sample Output
request services user-identification authentication-source authentication-source user-query
address ip-address
user@host> request services user-identification authentication-source aruba-clearpass user-query
address 40.0.0.1
user@host> request services user-identification authentication-sourc... | Command introduced in Junos OS Release 12.3X48-D30.
request services user-identification authentication-source jims groups | [] | |
domain <domain-name> (force-fetch|status) | request services user-identification authentication-source jims groups domain <domain-name>
request services user-identification authentication-source jims groups domain <domain-name>
status
request services user-identification authentication-source jims groups domain <domain-name>
force-fetch | You can request JIMS server to retrieve the group list for Active Directory (AD) domain using root logic-
system. There are no new requests triggered if the group query for the domain is ongoing. | [
{
"name": "force-fetch",
"desc": "This option is used to send out the group query even if you retrieve the group-list. The force-fetch does not take effect even if the group query is already sent out and that does not retrieve result."
},
{
"name": "status",
"desc": "This option displays the sta... | view
Sample Output
request services user-identification authentication-source jims groups domain <domain-
name> (force-fetch|status)
user@host> request services user-identification authentication-source jims groups domain <domain-
name>
node0:
--------------------------------------------------------------------------
u... | Command introduced in Junos OS Release 20.2R1. | [] | |
request services user-identification authentication-source jims validate | request services user-identification authentication-source jims validate (user <user-name>|group
<group-name>|device <device-name>) domain <domain-name> | Displays the list of status of some user or group or device information.
•
When the client-id or client secret is error, the command shows the unauthorized error in the
received status message.
•
When the server is offline, the command shows couldn’t connect to server error in the received
status message.
•
When the HT... | [
{
"name": "user-name",
"desc": "User ID."
},
{
"name": "group-name",
"desc": "Name of the group."
},
{
"name": "device-name",
"desc": "Name of the connected device."
},
{
"name": "domain-name",
"desc": "Name of the domain."
}
] | view
Output Fields
The following examples cover how to validate the valid user, device, and group for JIMS.
Sample Output
request services user-identification authentication-source jims validate (user <user-name>|
group <group-name>|device <device-name>) domain <domain-name>
The following commands are used to request J... | Command introduced in Junos OS Release 20.2R1. | [] | |
request services user-identification authentication-table delete | request services user-identification authentication-table delete (ip-address ip-address |
authentication-source (all | active-directory | authentication-source (domain domain-name |
group group-name |user user-name) ) | Delete entries from the ClearPass authentication table based on the IP address of the user’s device, or
on the authentication source and the name of a domain, a group, or a user. When only the
authentication source is specified, the entire ClearPass authentication table is deleted. For the
integrated ClearPass authenti... | [
{
"name": "ip-address",
"desc": "Deletes a user authentication entry from the ClearPass authentication table, and the Active Directory (AD) table, based on the IP address of the user’s device. NOTE: Starting with Junos OS Release 15.1X49-D130, SRX Series device supports to delete IPv6 addresses if IPv6 addr... | maintenance
Output Fields
The following examples cover how to delete various user entries from the ClearPass authentication
table based on the specified parameter. It also shows how to check to ensure that the user entries were
deleted successfully.
Sample Output
request services user-identification authentication-tabl... | Command introduced in Junos OS Release 12.3X48-D30. | [] | |
request services web-filter delete gencfg-data | request services web-filter delete gencfg-data | Delete url-filterd–ased objects. This is historical information.
WARNING: Do not use this command unless explicitly instructed to do so. | [] | view | Command introduced in Junos OS Release 18.3R1. | [
"Configuring URL Filtering"
] | |
request services web-filter force dns-resolution | request services web-filter force dns-resolution (all | profile profile-name)
<template template-name> | Force the domain name system (DNS) resolution request. | [
{
"name": "all",
"desc": "Force a DNS resolution request for all profiles."
},
{
"name": "profile profile-name",
"desc": "Force a DNS resolution request for the profile (all templates)."
},
{
"name": "template template-name",
"desc": "Force a DNS resolution request for the template."... | view | Command introduced in Junos OS Release 18.3R1. | [
"Configuring URL Filtering"
] | |
request services web-filter update dns-filter-database | request services web-filter update dns-filter-database filename | When you make changes to the domain filter database file, which is used in filtering DNS requests for
disallowed domains, apply the changes. | [
{
"name": "filename",
"desc": "File name of the database file."
}
] | maintenance | Command introduced in Junos OS Release 18.3R1.
Support added in Junos OS Release 19.3R2 for Next Gen Services on MX Series routers MX240, MX480
and MX960 with the MX-SPC3 services card. | [
"DNS Request Filtering for Disallowed Website Domains"
] | |
request services web-filter update url-filter-database file | request services web-filter update url-filter-database file filename | Update the URL filter database. If you change the database file, run this command. It sends a request to
the DNS server for only the new hostnames that were not in the previous version of the URL database
file. | [
{
"name": "filename",
"desc": "Use the database filename."
}
] | view | Command introduced in Junos OS Release 18.3R1. | [
"Configuring URL Filtering"
] | |
request services web-filter validate dns-filter-file-name | request services web-filter validate dns-filter-file-name filename hash-key key-string hash-
method hash-method-name | Validate the file format of the domain filter database file, which is used in filtering DNS requests for
disallowed domains. | [
{
"name": "filename",
"desc": "File name of the database file."
},
{
"name": "hash-method-name",
"desc": "Hash method you used to produce the hashed domain name values in the database file."
},
{
"name": "key-string",
"desc": "Hash key you used to produce the hashed domain name value... | maintenance | Command introduced in Junos OS Release 18.3R1.
Support added in Junos OS Release 19.3R2 for Next Gen Services on MX Series routers MX240, MX480
and MX960 with the MX-SPC3 services card. | [
"DNS Request Filtering for Disallowed Website Domains"
] | |
request services web-filter validate url-filter-file-name | request services web-filter validate (all | url-filter-file-name filename) | Validate the URL filter database to ensure the database is correct. | [
{
"name": "all",
"desc": "Validate the URL filter database for all profiles."
},
{
"name": "url-filter-file-name filename",
"desc": "Validate the URL filter database for the database file specified."
}
] | view | Command introduced in Junos OS Release 18.3R1. | [
"Configuring URL Filtering"
] | |
request session member | request session member member-id | Start a session with the specified member of a Virtual Chassis or a VCF. | [
{
"name": "member-id",
"desc": "Member ID for the specific member of the Virtual Chassis or VCF."
}
] | maintenance | Command introduced in Junos OS Release 9.0. | [
"Understanding Virtual Chassis Components"
] | |
request snmp spoof-trap | request snmp spoof-trap
<trap> variable-bindings <object> <instance> <value> | Spoof (mimic) the behavior of a Simple Network Management Protocol (SNMP) trap. | [
{
"name": "<trap>",
"desc": "Name of the trap to spoof."
},
{
"name": "variable-bindings",
"desc": ""
},
{
"name": "<object>",
"desc": ""
},
{
"name": "<instance>",
"desc": ""
},
{
"name": "<value>",
"desc": "(Optional) List of variables and values to include ... | request
Sample Output
request snmp spoof-trap (with Variable Bindings)
user@host> request snmp spoof-trap linkUp variable-bindings “ifIndex[14] = 14, ifAdminStatus[14]
= 1, ifOperStatus[14] = 2”
Spoof trap request result: trap sent successfully
user@host> request snmp spoof-trap jnxFruOnline variable-bindings "jnxFru... | Command introduced in Junos OS Release 8.2. | [] | |
request snmp utility-mib clear instance | request snmp utility-mib clear instance name
object-type type | Clear the data stored in the specified container object in the SNMP Utility MIB. | [
{
"name": "name",
"desc": "Name of the SNMP instance that is used to identify the data stored in the container object."
},
{
"name": "object-type type",
"desc": "Type of container object in which the data is stored. The following container object types"
},
{
"name": "are supported:",
... | clear | Command introduced in Junos OS Release 12.2. | [
"Understanding the Implementation of SNMP on the QFabric System"
] | |
request snmp utility-mib set instance | request snmp utility-mib set instance name
object-type type
object-value value | Store data in the specified container object in the SNMP Utility MIB. The data may be retrieved by
SNMP operations. | [
{
"name": "name",
"desc": "Name of the SNMP instance that is used to identify the data stored in the container object."
},
{
"name": "object-type",
"desc": ""
},
{
"name": "type",
"desc": "Type of container object in which to store data. The following container object types"
},
{... | request | Command introduced in Junos OS Release 12.2. | [
"Understanding the Implementation of SNMP on the QFabric System"
] | |
request stop system-counter-script | request stop system-counter-script | Stop the shell script that collects and archives system-state counters for debugging uses.
Here are some examples of times when you might use this command (this list is just a starting place; it is
not all-inclusive):
•
Using the request stop system-counter-script command to manage CPU usage—You might use this
command ... | [] | Command introduced in Junos OS Evolved Release 25.2R1. | [
"No Link Title"
] | ||
request support information | request support information
<archive>
<dot1x>
<evpn-mpls>
<evpn-vxlan>
<security-components component>
<with-components>
<with-logs>
<with-options> | Display all configuration data for the system, including data hidden with the apply-flags omit command.
Issue this command before contacting customer support, and then include the command output in your
support request. Output from this command varies somewhat, depending on which platform you issue
the command from. H... | [
{
"name": "brief",
"desc": "(Optional) Display brief information for the command output. Without this option, display of the output can take a long time to complete."
},
{
"name": "archive",
"desc": "Display a compressed archive file (tar.gz) in the /var/tmp/rsi directory containing all output f... | maintenance, view, and view-configuration
Output Fields
For information about output fields, see the description for the specific command-–listed in the output–
in which you are interested.
Sample Output
request support information | save
user@host> request support information | save hostA
Wrote 1143 lines of output t... | Command introduced before Junos OS Release 7.4.
Option brief introduced in Junos OS Release 13.2.
Option secure-gateway introduced in Junos OS Release 15.1X49-D110 for SRX5400, SRX5600, and
SRX5800 devices.
Options security-components and ipsec-vpn introduced in Junos OS Release 20.2R1.
Options evpn-mpls and evpn-vxlan... | [] | |
request system application (Junos OS Evolved) | request system application app application-name node node-name restart | Use this command to stop and then start (restart) an application on the specified node. Use the show
system applications command to verify if an application is started or stopped. | [
{
"name": "app application-name",
"desc": "Specify the application you want started or stopped."
},
{
"name": "node node-name",
"desc": "Specify the name of the node on which to start or stop the application."
},
{
"name": "restart",
"desc": "Restart the application. NOTE: Make sure ... | view
Sample Output
request system application app application-name node node-name restart
user@host> request system application app cmdd node fpc0 restart
This may affect traffic in the system. Proceed ? [yes,no] (no) yes
App cmdd on node fpc0 restart request is submitted | Command introduced in Junos OS Evolved Release 18.3R1. | [] | |
request system autorecovery state | request system autorecovery state (save | recover | clear) | Use this command to prepare the system for autorecovery of configuration, licenses, and disk
information.
In devices running FreeBSD Release 12 or later, you cannot back up data with the autorecovery feature.
Instead, back up data using snapshots. To learn if your device is running FreeBSD Release 12 or later,
issue th... | [
{
"name": "save",
"desc": "Save the current state of the disk partitioning, configuration, and licenses for autorecovery. The active Junos OS configuration is saved as the Junos rescue configuration, after which the rescue configuration, licenses, and disk partitioning information is saved for autorecovery.... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system autorecovery state save
user@host> request system autorecovery state save
Saving config recovery information
Saving license recovery information
Saving b... | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system boot console | request system boot-console <all-members|auxiliary|console|local|member> | Use this command to choose the port for early boot logs. | [
{
"name": "all-members",
"desc": "Switch boot-console port all virtual chassis members"
},
{
"name": "auxiliary",
"desc": "Set Auxiliary port as boot console"
},
{
"name": "console",
"desc": "Set Console port as boot console"
},
{
"name": "local",
"desc": "Switch boot-con... | maintenance
Sample Output
request system boot-console
user@host> request system boot-console
Command options:
console : RJ-45 console port
auxiliary : USB-C console port
(rest of the options are the usual option related to VC) | Command introduced in Junos OS Release 21.3R1. | [] | |
request system certificate add | request system certificate add (filename | terminal) | (Encryption interface on M Series and T Series routers, PTX Series, and QFX Series switches only) Add a
certificate provided by the Juniper Networks certificate authority (CA). | [
{
"name": "filename",
"desc": "Filename (URL, local, or remote)."
},
{
"name": "terminal",
"desc": "Use login terminal."
}
] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system certificate add terminal
user@host> request system certificate add terminal | Command introduced before Junos OS Release 7.4. | [] | |
request system commit server pause | request system commit server pause | Pause the commit server.
NOTE: If you issue this command when a commit job is in process, the batch commit
server pauses only after the current commit job is completed. | [] | view
Sample Output
When you enter the request system commit server pause command, you are provided feedback on the status
of your request.
request system commit server pause
user@host> request system commit server pause
Successfully paused the commit server. | Command introduced in Junos OS Release 12.1. | [
"Example: Configuring Batch Commit Server Properties"
] | |
request system commit server queue cleanup | request system commit server queue cleanup <id commit-id | job-status (error | pending |
success)> | Clean up the batch commit queue. Note that the id argument cleans up batch commit operation
messages for a specific commit ID, whereas job-status cleans up more broadly, based on categories of
status messages. You can use either option, but not both. | [
{
"name": "id commit-id",
"desc": "(Optional) Clean up batch commit operation status messages for a specific commit ID."
},
{
"name": "job-status",
"desc": "(Optional) Clean up batch commit operation status messages for the following:"
},
{
"name": "error",
"desc": "Clean up status m... | view
Sample Output
When you enter the request system commit server queue cleanup command, you are provided feedback on the
status of your request. The first example demonstrates cleaning up job ID 1008, while the second shows
a queue clean up for all jobs marked as successfully completed.
request system commit server q... | Command introduced in Junos OS Release 12.1. | [
"Example: Configuring Batch Commit Server Properties"
] | |
request system commit server start | request system commit server start | Start the commit server. | [] | view
Sample Output
When you enter the request system commit server start command, you are provided feedback on the status
of your request.
request system commit server start
user@host> request system commit server start
Successfully started the commit server. | Command introduced in Junos OS Release 12.1. | [
"Example: Configuring Batch Commit Server Properties"
] | |
request system configuration database resize | request system configuration database resize
<force>
<re0 | re1>
<routing-engine backup | master | both | local> | You might require to perform a resizing of the configuration database as a result of performing frequent
load replacement operations which replaces the configuration hierarchy with the new configuration.
When this occurs, deleted objects store in the database, and the memory allocated in the database is
freed after the... | [
{
"name": "force",
"desc": "(Optional) If there are uncommitted changes and you execute the request system configuration database resize command, the command will fail and an error will be generated (error: Database resize failed, Configuration Database Modified.). To execute the command when this occurs, u... | maintenance
Output Fields
Sample Output
request system configuration database resize
user@host> show system configuration database usage
Maximum size of the database: 1309.99 MB
Current database size on disk: 500.00 MB
Actual database usage: 176.81 MB
Available database space: 1133.18 MB
user@host> request system co... | Command introduced in Junos OS Release 17.2R1. | [] | |
request system configuration rescue delete | request system configuration rescue delete | Delete an existing rescue configuration.
NOTE: The [edit system configuration] hierarchy is not available on QFabric systems. | [] | maintenance
Output Fields
This command produces no output.
Sample Output
request system configuration rescue delete
user@host> request system configuration rescue delete | Command introduced before Junos OS Release 7.4.
Command introduced in Junos OS Evolved Release 20.4R2. | [] | |
request system configuration rescue save | request system configuration rescue save | Save the most recently committed configuration as the rescue configuration so that you can return to it
at any time by using the rollback command. If saved on a device with redundant Routing Engines, the
rescue configuration file is saved on both Routing Engines.
NOTE: The [edit system configuration] hierarchy is not a... | [] | maintenance
Output Fields
This command produces no output.
Sample Output
request system configuration rescue save
user@host> request system configuration rescue save | Command introduced before Junos OS Release 7.4.
Command introduced in Junos OS Evolved Release 20.4R2. | [] | |
request system convert-json-configuration | request system convert-json-configuration filename output-filename output-filename
<origin-schema schema> | Convert the JSON configuration data in the specified input file so that list keys precede any other
siblings within a list entry as required by the Junos schema. The converted data is saved in the specified
output file in the current working directory. The command does not emit output when the conversion is
successful... | [
{
"name": "filename",
"desc": "Path to the input JSON configuration file."
},
{
"name": "origin-schema",
"desc": ""
},
{
"name": "schema",
"desc": "(Optional) The schema that defines the input configuration data. Specify one of the"
},
{
"name": "following:",
"desc": ""
... | maintenance
Sample Output
request system convert-json-configuration
user@host> request system convert-json-configuration config.json output-filename config-
converted.json origin-schema openconfig
user@host> | Command introduced in Junos OS Release 22.1R1 and Junos OS Evolved Release 22.1R1. | [
"Load JSON Configuration Data With Unordered List Entries"
] | |
request system debug-info | request system debug-info
<mode custom | lite | normal | show-all>
<node node-name>
<noninteractive>
<outdir output-directory>
<since duration> | Collect debug information from Junos OS Evolved, such as logs. Logs are stored in the /var/tmp/
directory. Debug collector collects cores, application traces, configurations, commits and so on. It also
collects outputs from CLI and CLI-PFE commands. You need to login to the device as root user to use
this command. Ente... | [
{
"name": "mode",
"desc": ""
},
{
"name": "custom",
"desc": "Support for custom debug collection. The values are rpd, normal, lite, l2, evpn-mpls, l3,"
},
{
"name": "lite",
"desc": "You can use this option to run selected debug commands."
},
{
"name": "normal",
"desc": "Y... | view
Sample Output
request system debug-info
root@host> request system debug-info
Log collection time is dependent upon mode, total size of logs and the device's uptime.
Executing the command in lite mode with last 1d log collection is typically the fastest
(less than 30 minutes). Continue? [yes,no] (no) yes
Initializ... | Command introduced in Junos OS Evolved Release 18.3R1.
Option noninteractive introduced in Junos OS Release 23.4R2.
Option outdir introduced in Junos OS Evolved Release 25.3R1.
Option show-all mode introduced in Junos OS Evolved Release 25.3R1. | [] | |
request system decrypt password | request system decrypt password | Use to display plain text versions of obfuscated ($9) or encrypted ($8) passwords. If the password was
encrypted using the new $8$ method, you are prompted for the primary password. | [
{
"name": "decrypt",
"desc": "Decrypt a $8$-encrypted or $9$-encrypted password."
}
] | system
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
// Decrypting a $9 password
user@host> request system decrypt password $9$ABC123
Plaintext password: mysecret
Sample Output
// Decrypting a $8 password
user@host> request system decrypt password $8$A... | Statement introduced in Junos OS Release 16.2R1.
Statement introduced in Junos OS Evolved Release 22.4R1. | [
"Hardening Shared Secrets in Junos OS"
] | |
request system disable unified-services | request system disable unified-services | Disable Next Gen Services services on the MX Series.
Before you disable Next Gen Services, delete any router configuration for services. This includes
configuration under the [edit services] hierarchy, configuration for services interfaces, and any
configuration that refers to services interfaces.
After you enter requ... | [] | Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system disable unified-services
user@host> request system disable unified-services
Before disabling unified services, please move to baseline configuration.
Are above conditions satisfied ? [yes,no] | Command introduced in Junos OS Release 19.3R1. | [
"Enabling and Disabling Next Gen Services"
] | |
request system download abort | request system download abort <download-id> | Use this command to terminate a download. The download instance is stopped and cannot be resumed.
Any partially downloaded file is automatically deleted to free disk space. Information regarding the
download is retained and can be displayed with the show system download command until a request system
download clear ope... | [
{
"name": "download-id",
"desc": "(Required) The ID number of the download to be terminated."
}
] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system download abort
user@host> request system download abort 1
Aborted download #1 | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system download clear | request system download clear | Use this command to delete the history of completed and aborted downloads. | [] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system download clear
user@host> request system download clear
Cleared information on completed and aborted downloads | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system download pause | request system download pause <download-id> | Use this command to suspend a particular download instance. Downloads in the active state can be
paused. | [
{
"name": "download-id",
"desc": "(Required) The ID number of the download to be paused."
}
] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system download pause
user@host> request system download pause 1
Paused download #1 | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system download resume | request system download resume download-id <max-rate> | Use this command to resume a download that has been paused. You can resume the downloaded
instances that are not in progress because of an error or that have been explicitly paused. The file will
continue downloading from the point where it paused. By default, the download resumes with the same
bandwidth specified wit... | [
{
"name": "download-id",
"desc": "(Required) The ID number of the download to be resumed."
},
{
"name": "max-rate",
"desc": "(Optional) The maximum bandwidth for the download."
}
] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system download resume
user@host> request system download resume 1
Resumed download #1 | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system download start | request system download start (sftp-url | delay | identity-file | login | max-rate | passphrase
| save as ) | Use this command to create a download instance and identify it with a unique integer called the
download ID. | [
{
"name": "sftp-url",
"desc": "(Required) The FTP or HTTP URL location of the file to be downloaded securely."
},
{
"name": "delay",
"desc": "(Optional) The number of hours after which the download should start. Ranges from 1 through 48"
},
{
"name": "identity-file",
"desc": "(Requir... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system download start
user@host> request system download start identity-file mytestkey sftp://mysftpserver/homes/kelly/
test.tgz max-rate 200 save as newfile.tgz
Starting do... | Command introduced in Junos OS Release 15.1X49-D35. | [] | |
request system enable unified-services | request system enable unified-services | Enable Next Gen Services services on the MX Series.
Before you enable Next Gen Services, delete any router configuration for services. This includes
configuration under the [edit services] hierarchy, configuration for services interfaces, and any
configuration that refers to services interfaces.
After you enter request... | [] | Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system enable unified-services
user@host> request system enable unified-services
Before enabling unified services, please move to baseline configuration.
Are above conditions satisfied ? [yes,no] | Command introduced in Junos OS Release 19.3R1. | [
"Enabling and Disabling Next Gen Services"
] | |
request system filesystem encryption enable | request system filesystem encryption enable
<dry-run | re0 | re1>
Prerequisites
Following are the prerequisites to enable filesystem encryption:
•
System contains a TPM2.0 with IDevID provisioned.
•
System having single or redundant disk are supported.
•
Take data backup of configurations and log files. | When you enable encryption process on the filesystem, the conversion process starts with the backup
routing engine followed by the active Routing Engine. In the case of redundant disks, the conversion
starts with the primary disk followed by the secondary disk to avoid loss of data.
Once enabled, encryption cannot be d... | [
{
"name": "none",
"desc": "Enable filesystem encryption on all Routing Engines."
},
{
"name": "dry-run",
"desc": "(Optional) Display the filesystem encryption message without running the encryption process."
},
{
"name": "re0",
"desc": "(Optional) Enable filesystem encryption on RE0.... | maintenance
Sample Output
request system filesystem encryption enable (Junos OS)
user@host> request system filesystem encryption enable
Please check the message on enabling filesystem encryption enable using the dry-run option. i.e.
request system filesystem encrypton enable dry-run
Do you want to proceed ? [yes,no] (n... | Command introduced in Junos OS Release 22.3R1. | [
"Encryption with Trusted Platform Module"
] | |
request system filesystem encryption keys delete | request system filesystem encryption keys delete
<dry-run | re0 | re1 | routing-engine> | Key slots are the Keys used to encrypt an area or slot on the hard disk. You must enable file-system
encryption on the disk before deleting the key slots. After deleting the key slots, reboot the vmhost to
reflect the changes. You need to use USB based reinstall or recovery method to restore the system. | [
{
"name": "none",
"desc": "Erase all keyslots on all Routing Engines."
},
{
"name": "dry-run",
"desc": "(Optional) Display the keyslot deletion message without deleting any keyslots."
},
{
"name": "re0",
"desc": "(Optional) Erase all keyslots on RE0."
},
{
"name": "re1",
... | maintenance
Sample Output
request system filesystem encryption keys delete (Junos OS)
user@host> request system filesystem encryption keys delete
Please check the message on deleting filesystem encryption keyslots using the dry-run option.
i.e.
request system filesystem encrypton keys delete dry-run
Do you want to pro... | Command introduced in Junos OS Release 22.3R1. | [
"Encryption with Trusted Platform Module"
] | |
request system firmware optics switch (Junos OS Evolved) | request system firmware optics switch
<optics <(build-number | fpc-slot | image-version | part-number | pic-slot |
port)>> | This command starts running the image from the other (inactive) bank and commits it. If the no-commit
option is give, the command will only run the image. It will not make the image as default image.
Switching between active and inactive image.
•
Image A = version 1.0
•
Image B = version 1.2
If Image A is currently ru... | [
{
"name": "optics",
"desc": ""
},
{
"name": "suboptions",
"desc": "Use the request system firmware upgrade optics command to upgrade CMIS optics firmware on a system running Junos OS Evolved."
},
{
"name": "hitless",
"desc": "Perform hitless switch to other image."
},
{
"name... | [] | |||
request system firmware reload (Junos OS Evolved) | request system firmware reload
<fpc slot slot-number>
<sib slot slot-number> | CAUTION: Use extreme caution when using this command. You can cause significant
damage to your configuration if you use this command incorrectly.
Use this command to reload firmware after you issue the request system firmware upgrade operational mode
command. Requesting a firmware reload avoids having to power cycle th... | [
{
"name": "fpc slot slot-number",
"desc": "Reload FPC firmware."
},
{
"name": "slot slot-number",
"desc": "Specify the particular FPC slot (0-7) that should reload its"
},
{
"name": "sib slot slot-number",
"desc": "Reload SIB firmware."
},
{
"name": "slot slot-number",
"d... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request. | Command introduced in Junos OS Evolved Release 21.4R1. | [] | |
request system firmware upgrade (Junos OS Evolved) | request system firmware upgrade
<cb <(bcm-pfe | fancpld | fpga | port-fpga)>
<feb <(bcm-pfe | ctrl-fpga | dpll | i2cs-fpga | slot slot-number)>>
<fpc <(bcm-pfe | ctrl-fpga | dpll | dpll-cfg | i2cs-fpga | opticscpld<0|1|2|3> | slot slot-
number)>>
<ftc slot (0 | 1)>
<pic>
<poe (fpc-slot slot-number | poe-at-firmware | p... | After installing the jfirmware-junos-evo-install* package with the request system software add command, use
this command to upgrade firmware on a system running Junos OS Evolved. You can only upgrade one
option at a time; you cannot specify multiple options.
NOTE: For firmware upgrades on Junos OS Evolved, we recommend... | [
{
"name": "cb",
"desc": ""
},
{
"name": "suboptions",
"desc": "Upgrade control board firmware."
},
{
"name": "bcm-pfe",
"desc": "(Optional) Upgrade the BCM PFE chip."
},
{
"name": "cg0",
"desc": "(Optional) Upgrade the CG0."
},
{
"name": "fancpld",
"desc": "(O... | maintenance | [] | ||
request system firmware upgrade optics (Junos OS Evolved) | root@router> request system firmware upgrade optics ?Possible completions:
<[Enter]> Execute this command
firmware-path Enter firmware path
fpc-slot Slot number of FPC (0..0)
part-number Enter juniper optic part number
password Password to unlock firmware dow... | After installing the junos-evo-install*.iso package with the request system software add command, use the
request system firmware upgrade optics command to upgrade CMIS optics firmware on a system running
Junos OS Evolved.
NOTE: If the firmware file is not attached with this package, the users should copy this
firmware... | [
{
"name": "firmware-path",
"desc": "Path of the firmware bin file"
},
{
"name": "fpc-slot",
"desc": "Slot number of FPC"
},
{
"name": "part-number",
"desc": "Optic part number"
},
{
"name": "port",
"desc": "Slot number of port"
},
{
"name": "pic-slot",
"desc":... | [] | |||
request system firmware upgrade poe | request system firmware upgrade poe fpc-slot (number | all-members) <poe-at-firmware | poe-bt-
firmware> | Upgrade the PoE controller software on switches and line cards.
The Junos OS image running on the switch contains a copy of the PoE controller software. This
command compares the Junos OS version with the version of the software running on the PoE
controller. If the Junos OS version is a more recent version, the comman... | [
{
"name": "fpc-slot (number |",
"desc": ""
},
{
"name": "all-members)",
"desc": "Upgrade the PoE controller firmware for the Virtual Chassis member or line card specified by number, or for all Virtual Chassis members and line cards, specified by all-members."
},
{
"name": "poe-at-firmwar... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system firmware upgrade poe (Specific FPC Slot)
user@switch> request system firmware upgrade poe fpc-slot 8
Firmware upgrade initiated. Poe Upgrade takes about 10 minutes
Use 'show poe... | Command introduced in Junos OS Release 12.1.
Support for poe-at-firmware and poe-bt-firmware options introduced in 19.3 for EX4300-48MP switches. | [
"Upgrading the PoE Controller Software",
"Upgrading to IEEE 802.3bt PoE"
] | |
request system firmware upgrade | request system firmware upgrade
<allfw>
<bios <progress>
<cb <(fancpld | fpga | optics | port-fpga)>>
<cpld cpu <progress>>
<cpld sys <progress>>
<eth-switch>
<eusb <progress>>
<fpc <(bcm-pfe | dpll | dpll-cfg | opticscpld<0|1|2|3> | slot slot-number)>>
<fpga <(cb | re)>
<fpm... | Use this command to upgrade firmware and optics module on a system running Junos OS. | [
{
"name": "allfw",
"desc": "Upgrade all firmwares applicable in the jfirmware package."
},
{
"name": "bios",
"desc": "Upgrade BIOS."
},
{
"name": "progress",
"desc": "(Optional) Check the progress of BIOS upgrade."
},
{
"name": "cb",
"desc": "Upgrade baseboard FPGA."
},... | maintenance
Output Fields
When you enter this command, you are provided with the resulting status of the command.
Sample Output
request system firmware upgrade
user@host> request system firmware upgrade re bios
Part Type Tag Current Available Status
... | Command introduced in Junos OS Release 10.2.
cb option added in Junos OS Evolved Releases 21.1R2 and 21.2R1. Support for the MX10004 router
added in Junos OS Release 22.3R1.
pem option introduced in Junos OS Release 21.2R1.
sfb option introduced in Junos OS Release 21.4R1 for the MX10008 router. Support for the MX10004... | [
"Installing and Upgrading Firmware"
] | |
request system halt | request system halt
<at time>
<in minutes>
<media (compact-flash | disk | usb)>
<message "text"> | Stop the device software.
NOTE: When you issue this command on an individual component—for example, a Node
device—in a QFabric system, you will receive a warning that says “Hardware-based
members will halt, Virtual Junos Routing Engines will reboot.” If you want to halt only
one member of a Node group, issue this comma... | [
{
"name": "none",
"desc": "Stop the router or switch software immediately."
},
{
"name": "all-members",
"desc": "(Optional) Halt all members of the Virtual Chassis configuration."
},
{
"name": "at time",
"desc": "(Optional) Time at which to stop the software, specified in one of the ... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system halt
user@host> request system halt
Halt the system ? [yes,no] (no) yes
*** FINAL System shutdown message from root@section2 ***
System going down IMMEDIATELY
Terminated
...
sy... | Command introduced before Junos OS Release 7.4.
other-routing-engine option introduced in Junos OS Release 8.0.
director-device option introduced for QFabric systems in Junos OS Release 12.2.
backup-routing-engine option introduced in Junos OS Release 13.1. | [
"clear system reboot",
"request system power-off",
"request vmhost halt"
] | |
request system license update | request system license update | Starts autoupdating license keys from the license portal.
•
The request system license update command always uses the default Juniper license server: https://
ae1.juniper.net/.
•
The request system license update command is supported only on SRX, vSRX Virtual Firewall, and
QFX Series devices.
The products supported by ... | [
{
"name": "trial",
"desc": "Immediately updates trial license keys from the license portal."
}
] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system license update
user@host> request system license update
Trying to update license keys from https://ae1.juniper.net has been sent, use show system
license to check st... | Command introduced in Junos OS Release 9.5. | [] | |
request system logout | request system logout (pid pid | terminal terminal | user username)
<all> | Log out users from the router or switch and the configuration database. If a user held the configure
exclusive lock, this command clears the exclusive lock. | [
{
"name": "all",
"desc": "(Optional) Log out all sessions owned by a particular PID, terminal session, or user. (On a TX Matrix or TX Matrix Plus router, this command is broadcast to all chassis.)"
},
{
"name": "pid pid",
"desc": "Log out the user session using the specified management process i... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system logout
user@host> request system logout user test all
Connection closed by foreign host. | Command introduced before Junos OS Release 7.4. | [
"Log a User Out of the Device"
] | |
request system malware-scan | request system malware-scan
integrity-check
quick-scan
clean-action (clean | warn)
pids set-of-pids
test
run-fake-malware | list-fake-malware | Run the Juniper Malware Removal Tool (JMRT), which scans for and removes malware running on
Juniper Networks devices. This command can perform multiple types of scans, detailed in the following
section. | [
{
"name": "integrity-check",
"desc": "Check whether integrity mechanisms are enabled and working properly. Integrity mechanisms allow only signed binaries to run on the system. NOTE: Junos OS with Junos Automation Enhancements does not run Veriexec. As such, running the integrity-check command on Junos OS w... | admin
Sample Output
request system malware-scan
user@host> request system malware-scan integrity-check
Integrity is enforced: No
user@host> request system malware-scan list-fake-malware
user@host> request system malware-scan quick-scan
Found potential malware: No
user@host> request system malware-scan run-fake-ma... | Command introduced in Junos OS Release 19.2R1.
Command option veriexec-check renamed as integrity-check in Junos OS Release 21.4R1.
Command introduced in Junos OS Evolved Release 21.4R1. | [
"Juniper Malware Removal Tool",
"request system software add"
] | |
request system partition abort | request system partition abort
<all-members>
<local>
<member member-id> | Terminate a previously scheduled storage media partition operation. If the command is issued between
the time of a partition request and a reboot, the partition request is terminated and the storage media is
not affected. | [
{
"name": "all-chassis",
"desc": "(TX Matrix and TX Matrix Plus routers only) (Optional) Terminate a previously scheduled partition operation for all chassis."
},
{
"name": "all-lcc",
"desc": "(TX Matrix and TX Matrix Plus routers only) (Optional) On a TX Matrix router, terminate a previously sc... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system partition terminate
user@host> request system partition abort
The hard disk is no longer scheduled to be partitioned. | Command introduced before Junos OS Release 7.4.
sfc option introduced for the TX Matrix Plus router in Junos OS Release 9.6.
Command deprecated for Junos OS with Upgraded FreeBSD in Junos OS Release 15.1.
NOTE: To determine which platforms run Junos OS with Upgraded FreeBSD, see the
table listing the platforms currentl... | [] | |
request system partition compact-flash | request system partition compact-flash | Use this command to reboot the device and repartition the compact flash. The CompactFlash card is
repartitioned only if it is possible to restore all the data on the CompactFlash card. Otherwise, the
operation is terminated, and a message is displayed indicating that the current disk usage needs to be
reduced. | [] | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system partition compact-flash (If Yes)
user@host> request system partition compact-flash
Are you sure you want to reboot
and partition the compact-flash ? [yes,no] yes
Initia... | Command introduced in Junos OS Release 9.2.
Command deprecated for Junos OS with Upgraded FreeBSD in Junos OS Release 15.1.
NOTE: To determine which platforms run Junos OS with Upgraded FreeBSD, see the
table listing the platforms currently running Junos OS with upgraded FreeBSD in Release
Information for Junos OS with... | [] | |
request system partition hard-disk | request system partition hard-disk
<all-members>
<local>
<member member-id> | Set up the hard disk for partitioning. After this command is issued, the hard disk is partitioned the next
time the system is rebooted. When the hard disk is partitioned, the contents of /altroot and /altconfig
are saved and restored. All other data on the hard disk is at risk of being lost. | [
{
"name": "all-chassis",
"desc": "(TX Matrix routers and TX Matrix Plus routers only) (Optional) Schedule a partition of the hard disk for all routers in the chassis at its next reboot."
},
{
"name": "all-lcc",
"desc": "(TX Matrix and TX Matrix Plus routers only) (Optional) On a TX Matrix router... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system partition hard-disk
user@host> request system partition hard-disk
WARNING: The hard disk is about to be partitioned. The contents
WARNING: of /altroot and /altc... | Command introduced before Junos OS Release 7.4.
sfc option introduced for the TX Matrix Plus router in Junos OS Release 9.6.
Command deprecated for Junos OS with Upgraded FreeBSD in Junos OS Release 15.1.
NOTE: To determine which platforms run Junos OS with Upgraded FreeBSD, see the
table listing the platforms currentl... | [
"Routing Matrix with a TX Matrix Plus Router Solutions Page"
] | |
request system power-off (SRX Series) | request system power-off
at <time>
in <minutes>
junos
message <message>
network
oam
power-off
usb
media (compact-flash | disk | usb | internal) | Use this command to power off the system. | [
{
"name": "at time",
"desc": "Time at which to power off the system."
},
{
"name": "in minutes",
"desc": "Number of minutes to delay before powering off the system."
},
{
"name": "media",
"desc": "Boot media for the next boot."
},
{
"name": "compact-flash",
"desc": "Stand... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system power-off
user@host> request system power-off
Power Off the system ? [yes,no] (no) yes
Shutdown NOW!
[pid 3300]
*** FINAL System shutdown message from user@host ***
System goin... | Command introduced in Junos OS Release 11.4. | [] | |
request system power-off | request system power-off
<all-members>
<at time>
<both-routing-engines>
<in minutes>
<local>
<member>
<message "text">
<other-routing-engine>
<slice slice> | Power off the Routing Engines.
NOTE: When you issue this command on an individual component in a QFabric system,
you will receive a warning that says “Hardware-based members will halt, Virtual Junos
Routing Engines will reboot.” If you want to halt only one member, use the member option.
You cannot issue this command f... | [
{
"name": "none",
"desc": "Power off the router or switch software immediately."
},
{
"name": "all-members",
"desc": "(QFX Series devices only) (Optional) Power off all members of the Virtual Chassis configuration."
},
{
"name": "at time",
"desc": "(Optional) Time at which to power o... | maintenance
Output Fields
When you enter this command, you are provided feedback on the status of your request.
Sample Output
request system power-off
user@host> request system power-off message “This router will be powered off in 30 minutes.
Please save your data and log out immediately.”
warning: This command wil... | Command introduced in Junos OS Release 8.0. | [] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.