text
stringlengths
1
14.3k
https://www.amazon.com/Madison-Supply-Premium-Fluoride-Scissors/dp/B00YFG1U86/ref=sr_1_3?crid=36UNTRNDS31N2&dchild=1&keywords=trauma+shears&qid=1623891340&sprefix=trauma+s%2Caps%2C157&sr=8-3
They *will* cut my nickel or DULL TRYING
snipsnip
love the photo of someone using medical shears to cut gutters
Speaking of "Break it", my wife dumped her Vespa over while parking it and cracked her tibia in two places, so I'm full-time medical aide for the next 4-6 weeks.
It's a pisser that she just stuck her leg out to keep the damn thing from falling over and busted it.
It sucks getting old. (But being retired is awesome!)
Better the leg than landing on the shoulder and fucking up shoulder/ribs in a bad way. I had cracked ribs. Nothing can be done except pain for like a month at the slightest sneeze cough or laugh. Or picking up something etc. Never had a tib/femur break thou. At least not yet.
Last time I tried to cut something with tin snips. (Hint: Don't look)
my dad once had a moped tip over on him with the hot exhaust on his calf
2nd degree burn I'm pretty sure
it was on there a while
never understood why some moped riders insist on sticking their very breakable legs out forward/straight, knees locked, against unforgiving obstacles, but it's common enough here with emmo riders
do u have an exmaple? kinda hard to picture
at lower speed/coming to a stop or when turning at low speed for balance, it's fine if your knee can bend when/if it catches grip but locked out is a bit of asking to get bucked up/injured and drop the bike
the stance on the sit-down scooters doesn't help, in winter/slushy roads the less-experienced emmo riders here end up taking off from stops with both legs awkwardly out/forward, if either heel catches pavement they get bucked up/sideways
Only time my leg is out (never locked) is when I am about to come to a complete stop, or off roading purposely to kick the bike upright off a hill or something
With boots i am braver with the latter
@deleted_user_3f2cc2d1c92d always remember where your fingers are. also tin snips are awesome.
Oh I have a pair of these. They’re great
I blew up a phaserunner at the skate park, now I’m only front wheel drive :(
Oh no
How'd it happen
Go zoom then bang. Now phase to phase short
Wasn’t under stress at the time either
I can still smell the blown mosfet
*shudders*
Damn
My phaserunner gets a little toasty
but never seems like it's explodey
I did find a hover board thing in the parking lot though
They left it cause it wasn’t working
Just needed to be reset
This was hours later
you let that bomb in your house?
Has Samsung 22p cells and all are balanced
What setting were you running it at
And what were you doing lol
is set to 750w, was accelerating from a stop
Dafuq
How's your wires etc near connectors
My other phaserunner died
So the one for the rear wheel blow a mosfet or two and the one for the front wheel worked until I got home and unplugged it. This morning when I plugged it in and I got nothing. Even on the software it won’t detect it
Rip
@void loop ( ) inb4 it was your battery all along
Battery is at 54.6v
yeah but you dont just blow up 2 controllers
You can
What can a battery do to blow up a controller
Capacitor could maybe pop if you were doing regen at the time and battery cut out but you would have to reach a very high voltage
Iirc wasn’t a concern except for hv batteries
he was running 750W either combined or per controller and he managed to fry both of em
from stop
So what’s your theory
there must have been feedback somewhere
you may be right about regen either way it isnt normal
@void loop ( ) show us your setup
This but with phaserunners
send a pic of the phaserunners
like with it mounted on the frame
(if it still is)
2 different hub motors also is that front wheel bigger than rear
i know its not related but its curious
No, it’s just the angle
Will once I get home
Its all taken apart cause I was checking my wiring
@Akbar
Hmm interesting
How long have you been running this config?
step 1 get 2 phaserunners
step 2 duct tape
It’s a clever idea
Have you not seen Louis rossmann’s video?
step 3 duct tape entire bike
Purposefully make it look bad so no one steals it
https://youtu.be/suQx7lachDE?t=1097
Watch this, time stamped
ive seen it tho i dont think thats why he did it
void i mean
also this is the cable i used for my battery https://i.imgur.com/Rl0dSnY.png
Where did you get it from?
You actually have to derate it further since it’s no longer classed as two single cores like that
So looks nice but not as good for thermals
@izy
it came with the phaserunner
its meant to be anderson on the other end
A few months
The wires on that XT60 look thin
Can’t see any obvious faults
its 12awg ive checked when i soldered it directly to the battery
Exactly, I sent them an email. Didn't ask for replacements but ask for advice on what may have possibly happened. Even offered to mail them in so they can examine them
``Warranty covers items that fail when used within their normal operating parameters.
3 years on products designed and manufactured by GRIN (All Axle hub motor, Satiator charger, Phasernuner/Baserunner controller, Cycle Analyst Display, LiGo batteries etc.)``
``GRIN will repair or replace your item at our discretion
We will require you to go through a troubleshooting procedure prior to returning the item to GRIN. A majority of the problems people face do not require return shipment.
We do not have a "warranty void if opened" policy on any of our products or use that as an excuse to deny warranty. In fact, quite the contrary, we will usually require you to open up an item in order to help with troubleshooting and diagnostics before we will issue a warranty. We want our customers to become familiar with that is under the hood of their ebike. ``
https://ebikes.ca/shop/support/warranty.html
I've been through the pages, I work in customer service. We hate people that start off by immediately saying warranty so I just wanted to avoid that in the email
yeah i was pointed out you are covered but they will troubleshoot you first
i love this