hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.1.1.5 Test requirement | Same as the test requirements given in clause 7.5.8.1.1.5 with following exceptions:
- Table 7.5.8.1.1.5-1 is replaced by Table 17.5.4.1.1.5-1;
- Table 7.5.8.1.1.5-2 is replaced by Table 17.5.4.1.1.5-2;
Table 17.5.4.1.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Frequency Range
FR2
Duplex mode
TDD
TDD ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2 RRC based active TCI state switch for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1 NR SA FR2 RRC-CE based active TCI state switch for a known TCI state for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
- Test frequency f ≤ 40.8 GHz
- UE PC3
- The test is incomplete for UE power classes other than PC3
- The test is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.1 Test purpose | To verify the active TCI state switch delay requirement defined in TS 38.133 [6] clause 8.10B.5. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards supporting SA FR2, more than one TCI state configuration, and more than one simultaneously trackable TRS resource set. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.5.4.0.1 and 17.5.4.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.17.5.4.2.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.5.8.2.1.4.1 with following exceptions:
- Table 7.5.8.2.1.4.1-1 is replaced by Table 17.5.4.2.1.4.1-1;
- Table 7.5.8.2.1.4.1-2 is replaced by Table 17.5.4.2.1.4.1-2;
- Table 7.5.8.2.1.4.1-3 is replaced by Table 17.5.4.2.1.4.1-3;
Table 17.5.4.2.1.4.1-1: Supported test conf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.4.2 Test procedure | Same as the test procedure given in clause 7.5.8.2.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.4.3 Message contents | Same as the message contents given in clause 7.5.8.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.4.2.1.5 Test requirement | Same as the test requirements given in clause 7.5.8.2.1.5 with following exceptions:
- Table 7.5.8.2.1.5-1 is replaced by Table 17.5.4.2.1.5-1;
- Table 7.5.8.2.1.5-2 is replaced by Table 17.5.4.2.1.5-2;
Table 17.5.4.2.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Frequency Range
FR2
Duplex mode
TDD
TDD ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5 Uplink spatial relation switch delay for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1 MAC-CE based Spatial Relation switch for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.0 Minimum conformance requirements MAC-CE based uplink spatial relation switch delay | The spatial relation associated to DL RS is known if the following conditions are met:
- During the period from the last transmission of the DL RS resource used for the L1-RSRP measurement reporting for the target spatial relation to the completion of active spatial relation, where the DL RS resource for L1-RSRP measur... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1 NR SA FR2 MAC-CE based spatial relation switch associated with known DL-RS for 2 Rx UE | Editor’s Note: This test case is incomplete in following aspects:
- Message contents are still TBD.
TT analysis is available for the following configurations:
- Test frequency f ≤ 40.8 GHz
- UE PC3
- The test is incomplete for UE power classes other than PC3
- The test is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.1 Test purpose | To verify fulfillment of the uplink spatial relation switch delay requirement defined in 38.133 [6] clause 8.12A.3 by a UE capable of beam correspondence without the need for UL beam sweeping. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.2 Test applicability | This test applies to all types of NR RedCap UE from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.5.5.1.0.
The normative reference for this requirement is TS 38.133 [6] clause A.17.5.5.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.5.9.1.1.4.1 with following exceptions:
• Table 7.5.9.1.1.4.1-1 is replaced by Table 17.5.5.1.1.4.1-1;
• Table 7.5.9.1.1.4.1-2 is replaced by Table 17.5.5.1.1.4.1-2;
• Table 7.5.9.1.1.4.1-3 is replaced by Table 17.5.5.1.1.4.1-3;
Table 17.5.5.1.1.4.1-1: Supported test conf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.4.2 Test procedure | Same as the test procedure given in clause 7.5.9.1.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.4.3 Message contents | Same as the message contents given in clause 7.5.9.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.1.1.5 Test requirements | Same as the test requirements given in clause 7.5.9.1.1.5 with following exceptions:
• Table 7.5.9.1.1.5-1 is replaced by Table 17.5.5.1.1.5-1;
• Table 7.5.9.1.1.5-2 is replaced by Table 17.5.5.1.1.5-2.
Table 17.5.5.1.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Frequency Range
FR2
Duplex mode
TDD
TDD ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2 RRC based spatial relation switch for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.0 Minimum conformance requirements RRC based uplink spatial relation switch delay | The spatial relation associated to DL RS is known if the following conditions are met:
- During the period from the last transmission of the DL RS resource used for the L1-RSRP measurement reporting for the target spatial relation to the completion of active spatial relation, where the DL RS resource for L1-RSRP measur... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1 NR SA FR2 RRC-based spatial relation switch associated with a known DL-RS for 2 Rx UE | Editor’s Note: This test case is incomplete in following aspects:
- Message contents are still TBD.
TT analysis is available for the following configurations:
- Test frequency f ≤ 40.8 GHz
- UE PC3
- The test is incomplete for UE power classes other than PC3
-- The test is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.1 Test purpose | To verify fulfillment of the uplink spatial relation switch delay requirement defined in 38.133 [6] clause 8.12A.5 by a UE capable of beam correspondence without the need for UL beam sweeping. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.2 Test applicability | This test applies to all types of NR RedCap UE from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.5.5.2.0.
The normative reference for this requirement is TS 38.133 [6] clause A.17.5.5.2.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.4 Test description | Same as the test description given in clause 7.5.9.2.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.5.9.2.1.4.1 with following exceptions:
• Table 7.5.9.2.1.4.1-1 is replaced by Table 17.5.5.2.1.4.1-1;
• Table 7.5.9.2.1.4.1-2 is replaced by Table 17.5.5.2.1.4.1-2;
• Table 7.5.9.2.1.4.1-3 is replaced by Table 17.5.5.2.1.4.1-3;
Table 17.5.5.2.1.4.1-1: Supported test conf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.4.2 Test procedure | Same as the test procedure given in clause 7.5.9.2.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.4.3 Message contents | Same as the message contents given in clause 7.5.9.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.5.2.1.5 Test requirements | Same as the test requirements given in clause 7.5.9.2.1.5 with following exceptions:
• Table 7.5.9.2.1.5-1 is replaced by Table 17.5.5.2.1.5-1;
• Table 7.5.9.2.1.5-2 is replaced by Table 17.5.5.2.1.5-2.
Table 17.5.5.2.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Frequency Range
FR2
Duplex mode
TDD
TDD ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6 UE specific CBW change for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.0.1 Minimum conformance requirements for UE specific CBW change | The minimum conformance requirements given in clause 16.5.4.0.1 applies. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1 NR SA FR2 UE specific CBW change on PCell for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.1 Test purpose | To verify the UE specific CBW change delay requirement defined in 38.133 [6] clause 8.13A. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.5.6.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.5.6.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.4 Test description | The test scenario comprises of one Cell, PCell (Cell 1), which has constant signal levels throughout the test. The test consists of 1 time period with duration of T1.
During T1 the TE sends an RRCReconfiguration message containing SCS-SpecificCarrier to reconfigure UE-specific CBW. The test equipment verifies the UE sp... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.5.6.1.4.1-1.
Table 17.5.6.1.4.1-1: Supported test configurations
Config
Description
17.5.6.1-1
NR 120 kHz SSB SCS, 100 MHz bandwidth, TDD duplex mode
17.5.6.1-2
NR 240 kHz SSB SCS, 100 MHz bandwidth, TDD duplex mode
Note 1: The UE is only requir... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.4.2 Test procedure | 1. Ensure the UE is in state RRC_CONNECTED with generic procedure parameters Connectivity NR, Connected without release On and Test Mode On according to TS 38.508-1 [14] clause 4.5. UE has been configured with UE specific CBW (CBW-1), initial BWP (BWP-1) and firstActiveDownlinkBWP-Id indicating BWP-1 is the active BWP.... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.5.6.1.4.3-1:ServingCellConfigCommon (step 1, 3 and 8, test procedure)
Derivation Path: TS 38.508-1 [14], Table 4.6.3-168
Information Element
Value/remark
Comment
Condition
ServingCellConfigCommon::= SEQUENCE {
downlink... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.5.6.1.5 Test requirement | Table 17.5.6.1.4.1-3, Table 17.5.6.1.5-1 and Table 17.5.6.1.5-2 define the primary level settings including test tolerances.
Table 17.5.6.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Frequency Range
FR2
Duplex mode
TDD
TDD configuration
TDDConf.3.1
BWchannel
100 MHz: NRB,c = 66
Active DL BWP ID
1
Initi... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6 Measurement procedures for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1 Intra-frequency measurements for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.0.1 General | A measurement is defined as a SSB based intra-frequency measurement provided the centre frequency of the reference SSB of the serving cell and the centre frequency of the SSB of the neighbour cell are the same, and the subcarrier spacing of the two SSBs are also the same. The reference SSB is the SSB defined in BWP-spe... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.0.2 Minimum conformance requirements for event-triggered measurement without gap | The UE shall be able to identify a new detectable intra-frequency cell within Tidentify_intra_without_index_RedCap if the UE is not indicated to report SSB based RRM measurement result with the associated SSB index(reportQuantityRsIndexes or maxNrofRSIndexesToReport is not configured), or the UE is indicated that the n... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.0.3 Minimum conformance requirements for event-triggered measurement with gap | The UE shall be able to identify a new detectable intra frequency cell within Tidentify_intra_without_index_RedCap if UE is not indicated to report SSB based RRM measurement result with the associated SSB index (reportQuantityRsIndexes or maxNrofRSIndexesToReport is not configured), or the UE has been indicated that th... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1 NR SA FR2 event triggered reporting without gap in non-DRX for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
Test frequency f ≤ 40.8 GHz
UE PC3
This test case is incomplete for UE power classes other than PC3 (e.g. PC7)
This test case is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the TDD intra-frequency cell search requirements for RedCap in 38.133 [6] clause 9.2B.5.1 and 9.2B.5.2 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.2 Test applicability | This test applies to all types of NR RedCap UE from release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.1.0.1 and 17.6.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.6.1.1.4.1 with following exceptions:
- Table 7.6.1.1.4.1-1 is replaced by Table 17.6.1.1.4.1-1.
- Table 7.6.1.1.4.1-2 is replaced by Table 17.6.1.1.4.1-2.
Table 17.6.1.1.4.1-1: Supported test configurations
Test Config
Description
17.6.1.1-1
120 kHz SSB SCS, 100MHz bandw... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.4.2 Test procedure | Same as the test procedure given in clause 7.6.1.1.4.2 with following exceptions:
- Step 6 in test procedure in clause 7.6.1.1.4.2 is replaced by following steps.
6. UE shall transmit a MeasurementReport message triggered by Event A3. If the overall delays measured from the beginning of time period T2 is less than X ms... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.4.3 Message contents | Same as the message contents given in clause 7.6.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.1.5 Test requirement | Same as the test requirements given in clause 7.6.1.1.5 with following exceptions:
- Table 7.6.1.1.5-1 is replaced by Table 17.6.1.1.5-1.
- Table 7.6.1.1.5-2 is replaced by Table 17.6.1.1.5-2.
- X is
- 2.4s for a UE supporting power class 1 or 5,
- 1.44s for a UE supporting power class 2, 3, 4 or 7.
Table 17.6.1.1.5-1:... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2 NR SA FR2 event triggered reporting without gap in DRX for 2 Rx UE | Editor's Note: This test case is complete for the following configurations:
• Test frequency f ≤ 40.8 GHz
• UE PC3
This test case is incomplete for Test frequency f > 40.8 GHz
This test case is incomplete for UE power class other than PC3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.1 Test purpose | The purpose of this test is to verify that the UE makes correct reporting of an event. This test will partly verify the TDD intra-frequency cell search requirements in 38.133 [6] clause 9.2B.5.1 and 9.2B.5.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.2 Test applicability | This test applies to all types of NR RedCap UEs from release 17 supporting 5GS NR SA FR2 and long DRX cycle. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.1.0.1 and 17.6.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.4.1 Initial conditions | Same as the initial conditions given in clause 7.6.1.2.4.1 with following exceptions:
- Table 7.6.1.2.4.1-1 is replaced by Table 17.6.1.2.4.1-1.
- Table 7.6.1.2.4.1-2 is replaced by Table 17.6.1.2.4.1-2.
Table 17.6.1.2.4.1-1: Supported test configurations
Test Case ID
Description
7.6.1.2-1
120 kHz SSB SCS, 100MHz bandw... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.4.2 Test procedure | Same as the test procedure given in clause 7.6.1.2.4.2 with following exceptions:
6. UE shall transmit a MeasurementReport message triggered by Event A3. If the overall delays measured from the beginning of time period T2 is less than X ms for sub-test 1 or less than Y ms for sub-test 2 then the number of successful te... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.4.3 Message contents | Same as the message contents given in clause 7.6.1.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.2.5 Test requirement | Same as the test requirements given in clause 7.6.1.2.5 with following exceptions:
- For sub-test 1, X is
- X = 7202 for UE supporting power class 1 or 5;
- X = 4322 for UE supporting power class 2, 3, 4 or 7;
- For sub-test 2, X is
- X = 51202 for UE supporting power class 1 or 5;
- X = 30722 for UE supporting power c... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3 NR SA FR2 event triggered reporting with gap in non-DRX for 2 Rx UE | Editor's Note:
This test case is complete for the following configurations:
- UE PC3
- Test frequencies f ≤ 40.8 GHz;
This test case is incomplete for UE power classes other than PC3;
This test case is incomplete for test frequencies f > 40.8 GHz. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.1 Test purpose | The purpose of this test is to verify UE’s ability to make a correct reporting of an event with gaps under non-DRX within intra-frequency cell search with gaps requirements. This test will partly verify the TDD intra-frequency cell search requirements in TS 38.133 [6] clause 9.2B.6.1 and 9.2B.6.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards supporting CSI-RS based RLM and BWP operation without bandwidth restriction. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.1.0.1 and 17.6.1.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.1.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.4 Test description | Two cells are deployed in the test, which are FR1 PCell (Cell 1) and a FR1 neighbour cell (Cell 2) on the same frequency as the PCell. The general and cell specific test parameters for PCell and neighbour cell are given in Table 17.6.1.3.4.1-3, Table 17.6.1.3.5-1 and Table 17.6.1.3.5-2, respectively. In the measurement... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.1.3.4.1-1.
Table 17.6.1.3.4.1-1: Supported test configurations
Test Case ID
Description
17.6.1.3-1
120 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
17.6.1.3-2
240 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
Note: The UE is only required t... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.4.2 Test procedure | The test consists of two successive time periods, with time duration of T1, and T2 respectively. During time duration T1, the UE shall not have any timing information of Cell 2.
There are two BWPs configured in Cell 1, BWP1 which contains the cell defining SSB, and BWP2 which does not contain any SSB of Cell 1. During ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 4.6 with the following exceptions:
Table 17.6.1.3.4.3-1: Common Exception messages for NR SA FR1 event-triggered reporting with gap in non-DRX
Default Message Contents
Common contents of system information blocks exceptions
Default RRC messages and information e... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.3.5 Test requirement | Table 17.6.1.3.4.1-3 and Table 17.6.1.3.5-1 define the primary level settings including test tolerances.
Table 17.6.1.3.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Cell 2
T1
T2
T1
T2
TDD configuration
TDDConf.3.1
TDDConf.3.1
BWchannel
MHz
100: NRB,c = 66
100: NRB,c = 66
Data RBs allocated
Config 1
24
24... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4 NR SA FR2 event triggered reporting with gap in DRX for 2 Rx UE | Editor's Note:
This test case is complete for the following configurations:
- UE PC3
- Test frequencies f ≤ 40.8 GHz;
This test case is incomplete for UE power classes other than PC3;
• This test case is incomplete for test frequencies f > 40.8 GHz. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the TDD intra-frequency cell search requirements in TS 38.133 [6] clause 9.2B.6.1 and 9.2B.6.2 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards supporting CSI-RS based RLM, BWP operation without bandwidth restriction and long DRX cycle. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.1.0.1 and 17.6.1.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.4.1 Initial conditions | Same as the initial conditions given in clause 7.6.1.4.4.1 with following exceptions:
- Table 7.6.1.4.4.1-1 is replaced by Table 17.6.1.4.4.1-1.
- Table 7.6.1.4.4.1-2 is replaced by Table 17.6.1.4.4.1-2.
- Table 7.6.1.4.4.1-3 is replaced by Table 17.6.1.4.4.1-3.
Table 17.6.1.4.4.1-1: Supported test configurations
Test ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.4.2 Test procedure | Same as the test procedure given in clause 7.6.1.4.4.2 with following exceptions:
• Step 6 in clause 7.6.1.4.4.2 is replaced by:
6. UE shall transmit a MeasurementReport message triggered by Event A3. If the overall delays measured from the beginning of time period T2 is less than X ms for Test 1 or less than Y ms for ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.4.3 Message contents | Same as the message contents given in clause 7.6.1.4.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.1.4.5 Test requirement | Same as the test requirements given in clause 7.6.1.4.5 with following exceptions:
- Table 7.6.1.4.5-1 is replaced by Table 17.6.1.4.5-1.
- Table 7.6.1.4.5-2 is replaced by Table 17.6.1.4.5-2.
- In Test 1 the overall delay measured shall be less than a total of X ms, where
- X = 7202 for UE supporting power class 1 or ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2 Inter-frequency measurements for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.0 Minimum conformance requirements | The requirements in clause 17.6.2.0 apply, provided:
- The cell being identified or measured is detectable.
An inter-frequency cell shall be considered detectable when for each relevant SSB:
- For 2 Rx RedCap UE:
- SS-RSRP related side conditions given in 38.133 [6] clauses 10.1.4 and 10.1.5 for FR1 and FR2, respective... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1 NR SA FR2-FR2 event triggered reporting in non-DRX for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
Test frequency f ≤ 40.8 GHz
UE PC3
This test case is incomplete for UE power classes other than PC3 (e.g. PC7)
This test case is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the SA inter-frequency NR cell search requirements for RedCap in 38.133 [6] clause 9.3B.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.2 Test applicability | This test applies to all types of NR RedCap UE from release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.2.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.1.2.4.1-1.
Table 17.6.2.1.4.1-1: Supported test configurations
Test Config
Description
17.6.2.1-1
120 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
Configure the test requirement and the DUT according to the parameters in Table 17.6.1.2.4.1-2... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.4.2 Test procedure | Same as the test procedure given in clause 7.6.2.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.4.3 Message contents | Same as the message contents given in clause 7.6.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.1.5 Test requirement | Same as the test requirements given in clause 7.6.2.1.5 with following exceptions:
- Table 7.6.2.1.5-1 is replaced by Table 17.6.2.1.5-1.
Table 17.6.2.1.5-1: Cell specific test parameters for SA inter-frequency event triggered reporting for FR2 without SSB time index detection
Parameter
Unit
Test configuration
Cell 1
C... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2 NR SA FR2-FR2 event triggered reporting in DRX for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
Test frequency f ≤ 40.8 GHz
UE PC3
This test case is incomplete for UE power classes other than PC3 (e.g. PC7)
This test case is incomplete for test frequencies > 40.8 GHz |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.