hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the SA inter-frequency NR cell search requirements for RedCap in 38.133 [6] clause 9.3B.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.2 Test applicability | This test applies to all types of NR RedCap UE supporting long DRX cycle from release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.2.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.2.2.4.1-1.
Table 17.6.2.2.4.1-1: Supported test configurations
Test Config
Description
17.6.2.2-1
120 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
Configure the test requirement and the DUT according to the parameters in Table 17.6.2.2.4.1-2... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.4.2 Test procedure | Same as the test procedure given in clause 7.6.2.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.4.3 Message contents | Same as the message contents given in clause 7.6.2.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.2.5 Test requirement | Same as the test requirements given in clause 7.6.2.1.5 with following exceptions:
- Table 7.6.2.1.5-1 is replaced by Table 17.6.2.2.5-1.
Table 17.6.2.2.5-1: Cell specific test parameters for SA inter-frequency event triggered reporting for FR2 without SSB time index detection
Parameter
Unit
Test configuration
Cell 1
C... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3 NR SA FR2-FR2 event triggered reporting with SSB time index detection in non-DRX for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
Test frequency f ≤ 40.8 GHz
UE PC3
This test case is incomplete for UE power classes other than PC3 (e.g. PC7)
This test case is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the SA inter-frequency NR cell search requirements for RedCap in 38.133 [6] clause 9.3B.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.2 Test applicability | This test applies to all types of NR RedCap UE from release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.2.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.1.2.4.1-1.
Table 17.6.2.3.4.1-1: Supported test configurations
Test Config
Description
17.6.2.3-1
120 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
Configure the test requirement and the DUT according to the parameters in Table 17.6.1.2.4.1-2... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.4.2 Test procedure | Same as the test procedure given in clause 7.6.2.3.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.4.3 Message contents | Same as the message contents given in clause 7.6.2.3.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.3.5 Test requirement | Same as the test requirements given in clause 7.6.2.3.5 with following exceptions:
- Table 7.6.2.3.5-1 is replaced by Table 17.6.2.3.5-1.
Table 17.6.2.3.5-1: Cell specific test parameters for SA inter-frequency event triggered reporting for FR2 with SSB time index detection
Parameter
Unit
Test configuration
Cell 1
Cell... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4 NR SA FR2-FR2 event triggered reporting with SSB time index detection in DRX for 2 Rx UE | Editor's Note: This test case has been completed for the following configurations:
Test frequency f ≤ 40.8 GHz
UE PC3
This test case is incomplete for UE power classes other than PC3 (e.g. PC7)
This test case is incomplete for test frequencies > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.1 Test purpose | To verify that the UE makes correct reporting of an event. This test will partly verify the SA inter-frequency NR cell search requirements for RedCap in 38.133 [6] clause 9.3B.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.2 Test applicability | This test applies to all types of NR RedCap UE from release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.2.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.1.2.4.1-1.
Table 17.6.2.4.4.1-1: Supported test configurations
Test Config
Description
17.6.2.4-1
120 kHz SSB SCS, 100MHz bandwidth, TDD duplex mode
Configure the test requirement and the DUT according to the parameters in Table 17.6.1.2.4.1-2... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.4.2 Test procedure | Same as the test procedure given in clause 7.6.2.4.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.4.3 Message contents | Same as the message contents given in clause 7.6.2.4.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.2.4.5 Test requirement | Same as the test requirements given in clause 7.6.2.4.5 with following exceptions:
- Table 7.6.2.4.5-1 is replaced by Table 17.6.2.4.5-1.
Table 17.6.2.4.5-1: Cell specific test parameters for SA inter-frequency event triggered reporting for FR2 with SSB time index detection
Parameter
Unit
Test configuration
Cell 1
Cell... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3 L1-RSRP measurement for beam reporting for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.0 Minimum conformance requirements for L1-RSRP measurement for beam reporting | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.0.1 Minimum conformance requirements for SSB-based L1-RSRP measurement for beam reporting | The minimum requirements given in 5.6.3.0.1 applies.
The normative reference for this requirement is TS 38.133 [6] clause 9.5B.1, 9.5B.2, 9.5B.3.1, 9.5B.4.1 and 9.5B.5.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.0.2 Minimum conformance requirements for CSI-RS-based L1-RSRP measurement for beam reporting | The minimum requirements given in clause 5.6.3.0.2 applies.
The normative reference for this requirement is TS 38.133 [6] clauses 9.5B.1, 9.5B.2, 9.5B.3.3, 9.5B.4.2 and 9.5B.5.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1 NR SA FR2 SSB based L1-RSRP measurement in non-DRX for 2 Rx UE | Editor’s Notes:
This test case has been completed for the following configurations:
- Test frequencies f ≤ 40.8 GHz
- UE PC3
- This test case is incomplete for UE power classes other than PC3
- This test case is incomplete for Test frequencies f > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.1 Test purpose | To verify that the UE makes correct reporting of L1-RSRP measurement. This test will partly verify the L1-RSRP measurement requirements in TS 38.133 [6] clause 9.5B.4.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.3.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.3.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.6.3.1.4.1 with following exceptions:
- Table 7.6.3.1.4.1-1 is replaced by Table 17.6.3.1.4.1-1.
- Table 7.6.3.1.4.1-3 is replaced by Table 17.6.3.1.4.1-2.
Table 17.6.3.1.4.1-1: Supported test configurations
Test Case ID
Description
17.6.3.1.4.1-1
NR 120 kHz SSB SCS, 100 ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.4.2 Test procedure | Same as the test procedure given in clause 7.6.3.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.4.3 Message contents | Same as the test procedure given in clause 7.6.3.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.1.5 Test requirement | Same as the test requirements given in clause 7.6.3.1.5. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2 NR SA FR2 SSB based L1-RSRP measurement in DRX for 2 Rx UE | Editor’s Notes:
This test case has been completed for the following configurations:
- Test frequencies f ≤ 40.8 GHz
- UE PC3
This test case is incomplete for UE power classes other than PC3
This test case is incomplete for Test frequencies f > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.1 Test purpose | To verify that the UE makes correct reporting of L1-RSRP measurement. This test will partly verify the L1-RSRP measurement requirements in TS 38.133 [6] clause 9.5B.4.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards supporting long DRX cycle. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.3.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.3.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.4.1 Initial conditions | Same as the initial conditions given in 7.6.3.2.4.1 with following exceptions:
- Table 7.6.3.2.4.1-1 is replaced by Table 17.6.3.2.4.1-1.
- Table 7.6.3.2.4.1-3 is replaced by Table 17.6.3.2.4.1-2.
- Table 7.6.3.2.4.1-2 is replaced by Table 17.6.3.2.4.1-3.
Table 17.6.3.2.4.1-1: Supported test configurations
Test Config
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.4.2 Test procedure | Same as the test procedure given in clause 7.6.3.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.4.3 Message contents | Same as the message content given in 7.6.3.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.2.5 Test requirement | Same as the test requirements given in clause 7.6.3.2.5 with following exceptions:
- Table 7.6.3.2.5-1 is replaced by Table 17.6.3.2.5-1.
Table 17.6.3.2.5-1: Cell specific test parameters
Parameter
Config
Unit
SSB#0
SSB#1
T1
T2
T1
T2
Angle of arrival configuration
Setup 1 according to A.9
Assumption for UE beamsNote 4
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3 NR SA FR2 CSI-RS based L1-RSRP measurement in non-DRX for 2 Rx UE | Editor’s Notes:
This test case has been completed for the following configurations:
- Test frequencies f ≤ 40.8 GHz
- UE PC3
This test case is incomplete for UE power classes other than PC3
This test case is incomplete for Test frequencies f > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.1 Test purpose | To verify that the UE makes correct reporting of L1-RSRP measurement. This test will partly verify the L1-RSRP measurement requirements in TS 38.133 [6] clause 9.5B.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.3.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.3.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.4.1 Initial conditions | Same as the initial conditions given in 7.6.3.3.4.1 with following exceptions:
- Table 7.6.3.3.4.1-1 is replaced by Table 17.6.3.3.4.1-1.
- Table 7.6.3.3.4.1-3 is replaced by Table 17.6.3.3.4.1-2.
- Table 7.6.3.3.4.1-2 is replaced by Table 17.6.3.3.4.1-3.
Table 17.6.3.3.4.1-1: Supported test configurations
Test Config
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.4.2 Test procedure | Same as the test procedure given in clause 7.6.3.3.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.4.3 Message contents | Same as the message content given in 7.6.3.3.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.3.5 Test requirement | Same as the test requirements given in clause 7.6.3.3.5 with following exceptions:
- Table 7.6.3.3.5-1 is replaced by Table 17.6.3.3.5-1.
Table 17.6.3.3.5-1: Cell specific test parameters
Parameter
Config
Unit
CSI-RS#0
CSI-RS#1
Angle of arrival configuration
1
Setup 1 according to A.9
Beam AssumptionNote 3
1
Rough
Roug... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4 NR SA FR2 CSI-RS based L1-RSRP measurement in DRX for 2 Rx UE | Editor’s Notes:
This test case has been completed for the following configurations:
- Test frequencies f ≤ 40.8 GHz
- UE PC3
This test case is incomplete for UE power classes other than PC3
This test case is incomplete for Test frequencies f > 40.8 GHz |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.1 Test purpose | To verify that the UE makes correct reporting of L1-RSRP measurement. This test will partly verify the L1-RSRP measurement requirements in TS 38.133 [6] clause 9.5B.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.2 Test applicability | This test applies to all types of NR RedCap UEs from Release 17 onwards supporting long DRX cycle. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.3.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.3.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.4.1 Initial conditions | Same as the initial conditions given in 7.6.3.4.4.1 with following exceptions:
- Table 7.6.3.4.4.1-1 is replaced by Table 17.6.3.4.4.1-1.
- Table 7.6.3.4.4.1-3 is replaced by Table 17.6.3.4.4.1-2.
- Table 7.6.3.4.4.1-2 is replaced by Table 17.6.3.4.4.1-3.
Table 17.6.3.4.4.1-1: Supported test configurations
Test Config
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.4.2 Test procedure | Same as the test procedure given in clause 7.6.3.4.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.4.3 Message contents | Same as the message content given in 7.6.3.4.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.3.4.5 Test requirement | Same as the test requirements given in clause 7.6.3.4.5 with following exceptions:
- Table 7.6.3.4.5-1 is replaced by Table 17.6.3.4.5-1.
Table 17.6.3.4.5-1: Cell specific test parameters
Parameter
Config
Unit
CSI-RS#0
CSI-RS#1
Angle of arrival configuration
1
Setup 1 according to A.9
Beam AssumptionNote 3
1
Rough
Roug... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4 NR Measurements with autonomous gaps for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.0.1 Minimum conformance requirements for CGI identification of an NR cell with autonomous gaps | The UE shall identify and report the CGI of a known NR target cell when requested by the network for the purpose of reportCGI. Only one cell is provided to the UE with cellForWhichToReportCGI for identifying the CGI.The UE may make autonomous gaps in both downlink reception and uplink transmission for receiving MIB and... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1 NR SA FR2-FR2 CGI identification of NR neighbour cell for 2 Rx UE | Editor’s Note: This test case is incomplete in following aspects:
- TT analysis is still missing. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.1 Test purpose | To verify that the UE makes correct reporting of an CGI. This test will partly verify the SA inter-frequency NR cell search requirements in TS 38.133 [6] clause 9.11A. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards supporting FR2 and acquisition of CGI from neighbour NR cell using autonomous gap. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.6.4.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.6.4.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.4 Test description | The test scenario comprises of two NR carriers and two NR cells: NR cell 1 as PCell in FR2 on NR RF channel 1 and NR cell 2 as neighbour cell in FR2 on NR RF channel 2.
The test consists of three successive time periods, with time durations of T1 and T2 respectively:
- Measurement gap patterns are configured. During T1... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.6.4.1.4.1-1.
Table 17.6.4.1.4.1-1: Supported test configurations
Configuration
Description
17.6.4.1-1
120 kHz SSB SCS, 100 MHz bandwidth, TDD duplex mode
Note: The UE is only required to be tested in one of the supported test configurations
Conf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.4.2 Test procedure | Throughout the test, the UE shall be scheduled to perform DL reception on every slot suitable for DL.
1. Ensure the UE is in State RRC_CONNECTED with generic procedure parameters Connectivity NR, Connected without release On according to TS 38.508-1 [14] clause 4.5. Establish SRB2 and DRB in the RRC Reconfiguration mes... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.6.4.1.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Default RRC messages and information elements contents exceptions
Table H.3.1-1
Table H.3.1-7 with... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.6.4.1.5 Test requirements | Table 17.6.4.1.4.1-3 and Table 17.6.4.1.5-1 define the primary level settings including test tolerances for the test.
Table 17.6.4.1.5-1: NR Cell specific test parameters
Parameter
Unit
Cell 1
Cell 2
T1
T2
T1
T2
AoA setup
Setup 3 as specified in clause A.3.15
AoA1
AoA2
Beam AssumptionNote 7
Rough
NR RF Channel Number
1... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7 Measurement performance requirements for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1 SS-RSRP for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.0.1 Intra-frequency SS-RSRP measurement accuracy requirements | Same as in clause 5.7.1.0.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.0.2 Inter-frequency SS-RSRP measurement accuracy requirements | Same as in clause 5.7.1.0.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1 NR SA FR2 SS-RSRP measurement accuracy for 2 Rx UE | Editor’s Note: This test case has been completed for the following configurations:
- Test frequency f ≤ 40.8 GHz
- UE PC3
- Normal conditions
- The test is incomplete for UE power classes other than PC3
- The test is incomplete for test frequencies > 40.8 GHz
- The test is incomplete for extreme conditions |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.1 Test purpose | To verify that the intra-frequency SS-RSRP measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.2 Test applicability | This test applies to all types of NR RedCap UE from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.7.1.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.7.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.4 Test description | Same as the test description given in clause 7.7.1.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.7.1.1.4.1 with following exceptions:
• Table 7.7.1.1.4.1-1 is replaced by Table 17.7.1.1.4.1-1;
• Table 7.7.1.1.4.1-2 is replaced by Table 17.7.1.1.4.1-2;
Table 17.7.1.1.4.1-1: Supported test configurations
Configuration
Description
17.7.1.1-1
120 kHz SSB SCS, 100 MHz ba... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.4.2 Test procedure | Same as the test procedure given in clause 7.7.1.1.4.2 with following exceptions:
- Table 7.7.1.1.5-1 is replaced by Table 17.7.1.1.5-1;
- Table 7.7.1.1.5-2 is replaced by Table 17.7.1.1.5-2;
- Table 7.7.1.1.5-3 is replaced by Table 17.7.1.1.5-3;
- Table 7.7.1.1.5-3a is replaced by Table 17.7.1.1.5-4;
- Table 7.7.1.1.5... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.4.3 Message contents | Same as the message contents given in clause 7.7.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.1.5 Test requirement | Same as the test requirements given in clause 7.7.1.1.5 with followings exceptions:
- Table 7.7.1.1.5-1 is replaced by Table 17.7.1.1.5-1;
- Table 7.7.1.1.5-2 is replaced by Table 17.7.1.1.5-2;
- Table 7.7.1.1.5-3 is replaced by Table 17.7.1.1.5-3;
- Table 7.7.1.1.5-3a is replaced by Table 17.7.1.1.5-4;
- Table 7.7.1.1... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2 NR SA FR2-FR2 SS-RSRP measurement accuracy for 2 Rx UE | Editor’s Note: This test case has been completed for the following configurations:
- Test frequency f ≤ 40.8 GHz
- UE PC3
- Normal conditions
- The test is incomplete for UE power classes other than PC3
- The test is incomplete for test frequencies > 40.8 GHz
- The test is incomplete for extreme conditions17.7.1.2.1 Te... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.2 Test applicability | This test applies to all types of NR RedCap UE from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.7.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.7.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.4 Test description | Same as the test description given in clause 7.7.1.2.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.4.1 Initial conditions | Same as the initial conditions given in clause 7.7.1.2.4.1 with following exceptions:
• Table 7.7.1.2.4.1-1 is replaced by Table 17.7.1.2.4.1-1;
• Table 7.7.1.2.4.1-2 is replaced by Table 17.7.1.2.4.1-2;
Table 17.7.1.2.4.1-1: Supported test configurations
Configuration
Description
17.7.1.2-1
120 kHz SSB SCS, 100 MHz ba... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.4.2 Test procedure | Same as the test procedure given in clause 7.7.1.1.4.2 with following exceptions:
- Table 7.7.1.2.5-1 is replaced by Table 17.7.1.2.5-1;
- Table 7.7.1.2.5-2 is replaced by Table 17.7.1.2.5-2;
- Table 7.7.1.2.5-3 is replaced by Table 17.7.1.2.5-3;
- Table 7.7.1.2.5-3a is replaced by Table 17.7.1.2.5-4;
- Table 7.7.1.2.5... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.4.3 Message contents | Same as the message contents given in clause 7.7.1.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.7.1.2.5 Test requirement | Same as the test requirements given in clause 7.7.1.2.5 with followings exceptions:
- Table 7.7.1.2.5-1 is replaced by Table 17.7.1.2.5-1;
- Table 7.7.1.2.5-2 is replaced by Table 17.7.1.2.5-2;
- Table 7.7.1.2.5-3 is replaced by Table 17.7.1.2.5-3;
- Table 7.7.1.2.5-3a is replaced by Table 17.7.1.2.5-4;
- Table 7.7.1.2... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.