hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and AWGN noise source and fading simulators to the UE antenna connector as shown in figure Figure A.11.
2) The UL Reference Measurement Channel parameters are defined in Annex C.11.
3) Set the... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.3.2.4.2 Procedure | NOTE: The measurement principle of the missed hold test (step 3 to 5) is as follows: Upon the UE transmission on E-DPCCH and E-DPDCH, the SS responds as follows: Cell 1 responds "up" on the E-RGCH and a fixed SG on the E-AGCH. Cell 2 responds DTX=hold. The SS reads the transport format, signalled on the E-DPCCH, corres... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.3.2.5 Test Requirements | For table 10.3.2.5.1, the missed HOLD probability shall be below the specified value in Table 10.3.2.5.2. For table 10.3.2.5.1, the average downlink E-RGCH Ec/Ior power ratio shall be below the specified value for the missed DOWN probabilities in Table 10.3.2.5.3
Table 10.3.2.5.1: Test scenario parameters for E-RGCH – ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4 Demodulation of E-DCH Absolute Grant Channel (E-AGCH) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1 Single link performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.1 Definition and applicability | The receive characteristics of the E-DCH Absolute Grant Channel (E-AGCH) in multi-path fading environment is determined by the missed detection probability. The requirements and this test apply to Release 6 and later releases for all types of UTRA for the FDD UE that support HSDPA and E-DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.2 Minimum requirement | For the parameters specified in Table 10.4.1.1 the average downlink E-AGCH Ec/Ior power ratio shall be below the specified value for the missed detection probability in Table 10.4.1.2.
Table 10.4.1.1: Test parameters for E-AGCH detection – single link
Parameter
Unit
Missed detection
dBm/3.84 MHz
-60
Phase reference
-
P... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.3 Test Purpose | The aim of the test is to verify that the missed detection probability of the E-AGCH channel does not exceed 0.01. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.4.1 Initial conditions | Test environment: normal; see clause G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4
1) Connect the SS and AWGN noise source and fading simulator to the UE antenna connector as shown in Figure A.10.
2) The UL Reference Measurement Channel parameters are defined in Annex C.11.
3) Set the test para... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.4.2 Procedure | 1) The SS shall signal 100% ACK on the E-HICH for all processes.
2) The SS shall signal the Absolute Grants according to the E-AGCH information sequence as defined in Table 10.4.1.3.
3) The SS shall analyse the E-TFCI transmitted on the E-DPCCH for each E-DCH TTI to determine if a missed detection event has occurred by... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 10.4.1.5 Test Requirements | The missed detection probability shall not exceed to the values specified in Table 10.4.1.3a.
The missed detection probability = the ratio of (missed detection event)/ (all detected E-TFCI event) ≤ 0.01.
Tables 10.4.1.3 and 10.4.1.3a define the primary level settings including test tolerance and test parameters for the... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11 Performance requirement (MBMS) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.1 General | The performance requirements for the UE in this subclause are specified for the propagation conditions specified in Annex D.2 and the Downlink Physical channels specified in Annex E.5B.
Unless otherwise stated the receiver characteristics are specified at the antenna connector of the UE. For UEs with more than one rece... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2 Demodulation of MTCH | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.1 Definition and applicability | The receive characteristic of the MTCH is determined by RLC SDU error rate (RLC SDU ER). RLC SDU ER is specified for each individual data rate of the MTCH. The requirement is valid for all RRC states for which the UE has capabilities for MBMS.
The requirements and this test apply to Release 6 and later releases for all... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.2 Minimum requirement | For the parameters specified in Table 11.2.2.1 the average downlink S-CCPCH_Ec /Ior power ratio shall be below the specified value for the RLC SDU ER shown in Table 11.2.2.2.
Table 11.2.2.1: Parameters for MTCH detection
Parameter
Unit
Test 1
Test 2
Test 3
Phase reference
-
P-CPICH
dBm/3.84 MHz
-60
dB
-3
-3
-3
MTCH Dat... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.3 Test Purpose | The aim of the test is to verify that the RLC SDU error rate (RLC SDU ER) for each individual data rate of the MTCH channel does not exceed 0.1. The test shall be performed in CELL_PCH state only. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and AWGN noise source and fading simulator to the UE antenna connector as shown in Figure A.23.
2) The DL Reference Measurement Channel parameters are defined in Annex C.12.1.
3) The configura... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.4.2 Procedure | 1) Initiate the variables NSS_ACC to 0.
2) SS shall start the test by sending valid MAC headers and RLC SDUs on the MTCH radio bearer for 164 seconds (10 seconds in the second or later iteration) on each Radio Link. The delays of Radio Link 2 and 3 compared with Radio Link 1 are specified in Table 11.2.5.1. SS stores t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.2.5 Test Requirements | Table 11.2.5.1: Parameters for MTCH detection
Parameter
Unit
Test 1
Test 2
Test 3
Phase reference
-
P-CPICH
dBm/3.84 MHz
-60
Cell1
dB
-2.4
-2.4
-2.4
Cell2
dB
-2.4
-2.4
-2.4
Cell3
dB
-2.4
-2.4
-2.4
MTCH Data Rate
128 kbps
256 kbps
128 kbps
Transmission Time Interval
ms
40
40
80
Propagation condition
VA3
Number of Radio ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3 Demodulation of MTCH and cell identification | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.1 Definition and applicability | MBMS combining is not controlled by a network but instead it is autonomously handled by a terminal. UE has to be able to receive MTCH and identify intra-frequency neighbour cells according to the requirements. The receive characteristic of the MTCH combined with cell identification is determined by RLC SDU error rate (... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.2 Minimum requirements | For the parameters specified in Table 11.3.2.1 the average downlink S-CCPCH_Ec/Ior power ratio shall be below the specified value for the RLC SDU error rate shown in Table 11.3.2.2. The cell reselection parameters are given in clause in Table 11.3.2.3. The different cells are assumed to be time aligned.
Table 11.3.2.1:... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.3 Test purpose | To verify that the SDU error rate does not exceed the value at the S-CCPCH_Ec/Ior specified in table 11.3.2.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and AWGN noise source and fading simulators to the UE antenna connector as shown in Figure A.23.
2) The DL Reference Measurement Channel (128kbps 40ms TTI) parameters are defined in Annex C.12... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.4.2 Procedures | 1) Initiate the variables NSS to 0.
2) The SS configures and activates cell 1 to 3 with RF parameters according to Stage 1 conditions in Table 11.3.5.1.
3) The SS transmits valid MAC headers and RLC SDUs on the MTCH radio bearer for 2 seconds during Stage 1, 0.8 seconds during Stage 2 and 2 seconds during T3. The SS ch... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 11.3.5 Test requirements | The test parameters are specified in table 11.3.5.1.
Table 11.3.5.1: Parameters for MTCH demodulation requirements with cell identification
Parameter
Unit
Test 1
Stage 1
Stage 2
Stage 2
Time in each stage
S
2
0.8
2
Phase reference
-
P-CPICH
dBm/3.84 MHz
-70
-73
-70
Cell1
dB
-2.4
0.6
-2.4
Cell2
dB
-2.4
0.6
-infinity
Cel... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 1 Scope | The present document specifies the protocol conformance testing for testing a MCData Server for compliance to the Mission Critical Data (MCData) over LTE protocol requirements defined by 3GPP. The present document addresses only MCData Server-Client, and, MCData Server-Server communication scenarios. It does not cover ... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 2 References | The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or non‑specific.
- For a specific reference, subsequent revisions do not apply.
- Fo... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 3 Definitions of terms, symbols and abbreviations | |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 3.1 Terms | For the purposes of the present document, the terms given in TR 21.905 [1] and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
For the purpose of the present document, the following terms given in TS 23.282 [33] apply:
Auto-rec... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 3.2 Symbols | Void. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 3.3 Abbreviations | For the purposes of the present document, the abbreviations given in 3GPP TR 21.905 [1] and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in 3GPP TR 21.905 [1].
CSK Client-Server Key
DS Data Streaming
ECGI E-UTRAN Cell Glob... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4 General | |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.1 Test methodology | |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.1.1 Testing of optional functions and procedures | Any function or procedure which is optional, may be subject to a conformance test if it is implemented in the MCData Server.
A declaration by the MCData Server supplier (to use the Implementation Conformance Statement (ICS) proforma specified in TS 36.579-4 [4]) is used to determine whether an optional function/procedu... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.1.2 Test interfaces and facilities | Detailed descriptions of the MCData test interfaces and special facilities for testing are provided in TS 36.509 [19]. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.2 Implicit testing | For some 3GPP MCData protocol features conformance is not verified explicitly in the present document. This does not imply that correct functioning of these features is not essential, but that these are implicitly tested to a sufficient degree in tests which are not explicitly dedicated to test the feature. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.3 Repetition of tests | As a general rule, the test cases specified in the present document are highly reproducible and do not need to be repeated unless otherwise stated. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.4 Handling of differences between conformance requirements in different releases of cores specifications | The conformance requirements which determine the scope of each test case are explicitly copy-pasted from relevant core specifications in the especially dedicated for this clause of each test with the title 'Conformance requirements'.
NOTE: When in the copy/pasted text there are references to other specifications the re... |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.5 Reference conditions | The reference environments used by all signalling and protocol tests is specified in TS 36.579-1 [2]. Where a test requires an environment that is different, this will be specified in the test itself.
For all test cases in this document unless specified otherwise the condition MCDATA applies for all message contents. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 4.6 Generic setup procedures | A set of basic generic procedures for MCData Client-Server communication are described in TS 36.579-1 [2]. These procedures will be used in numerous test cases throughout the present document. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 5 MCData Client Configuration | Editor’s Note: Intended for MCData server conformance test cases for configuration, authentication, authorization, and registration. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 6 MCData Server - MCData Client operation | Editor’s Note: Intended for MCData server conformance test cases for communications between the MCData server under test and a client. |
d3d27ffa25f98b699e8f75bb3e42d6fe | 36.579-9 | 7 MCData Server - MCData Server operation | Editor’s Note: Intended for MCData server conformance test cases for communications between the MCData server under test and another MCData server.
Annex A (informative):
Change history
Change history
Date
Meeting
TDoc
CR
Rev
Cat
Subject/Comment
New version
2023-03
RAN5#98
R5-230771
-
-
-
Introduction of TS 36.579-9
0.... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 1 Scope | The present document specifies the protocol conformance testing for testing a MCVideo Server for compliance to the Mission Critical Video (MCVideo) over LTE protocol requirements defined by 3GPP. The present document addresses only MCVideo Server-Client, and, MCVideo Server-Server communication scenarios. It does not c... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 2 References | The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or non‑specific.
- For a specific reference, subsequent revisions do not apply.
- Fo... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 3 Definitions of terms, symbols and abbreviations | |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 3.1 Terms | For the purposes of the present document, the terms given in TR 21.905 [1] and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
For the purpose of the present document, the following terms and definitions given in TS 24.281 [26]... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 3.2 Symbols | Void. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 3.3 Abbreviations | For the purposes of the present document, the abbreviations given in TR 21.905 [1] and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 [1].
ECGI E-UTRAN Cell Global Identification
FFS For Further Study
ICS Implem... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4 General | |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.1 Test methodology | |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.1.1 Testing of optional functions and procedures | Any function or procedure which is optional, may be subject to a conformance test if it is implemented in the MCVideo Server.
A declaration by the MCVideo Server supplier (to use the Implementation Conformance Statement (ICS) proforma specified in TS 36.579-4 [4]) is used to determine whether an optional function/proce... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.1.2 Test interfaces and facilities | Detailed descriptions of the MCVideo test interfaces and special facilities for testing are provided in TS 36.509 [19]. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.2 Implicit testing | For some 3GPP MCVideo protocol features conformance is not verified explicitly in the present document. This does not imply that correct functioning of these features is not essential, but that these are implicitly tested to a sufficient degree in tests which are not explicitly dedicated to test the feature. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.3 Repetition of tests | As a general rule, the test cases specified in the present document are highly reproducible and do not need to be repeated unless otherwise stated. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.4 Handling of differences between conformance requirements in different releases of cores specifications | The conformance requirements which determine the scope of each test case are explicitly copy-pasted from relevant core specifications in the especially dedicated for this clause of each test with the title 'Conformance requirements'.
NOTE: When in the copy/pasted text there are references to other specifications the re... |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.5 Reference conditions | The reference environments used by all signalling and protocol tests is specified in TS 36.579-1 [2]. Where a test requires an environment that is different, this will be specified in the test itself.
For all test cases in this document unless specified otherwise the condition MCVIDEO applies for all message contents. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 4.6 Generic setup procedures | A set of basic generic procedures for MCVideo Client-Server communication are described in TS 36.579-1 [2]. These procedures will be used in numerous test cases throughout the present document. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 5 MCVideo Client Configuration | Editor’s Note: Intended for MCVideo server conformance test cases for configuration, authentication, authorization, and registration. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 6 MCVideo Server - MCVideo Client operation | Editor’s Note: Intended for MCVideo server conformance test cases for communications between the MCVideo server under test and a client. |
13cb58e12ff5ede787a144eecae59b45 | 36.579-8 | 7 MCVideo Server - MCVideo Server operation | Editor’s Note: Intended for MCVideo server conformance test cases for communications between the MCVideo server under test and another MCVideo server.
Annex A (informative):
Change history
Change history
Date
Meeting
TDoc
CR
Rev
Cat
Subject/Comment
New version
2023-03
RAN5#98
R5-230770
-
-
-
Introduction of TS 36.579-8... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 1 Scope | The present document is a technical report for Dual Connectivity (EN-DC) of 1 LTE band (1DL/1UL) and 1 NR band (1DL/1UL) under Rel-16 time frame. The purpose is to gather the relevant background information and studies in order to address Dual Connectivity (EN-DC) of 1 LTE band (1DL/1UL) and 1 NR band (1DL/1UL)for the ... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 2 References | The following documents contain provisions which, through reference in this text, constitute provisions of the present document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or non‑specific.
- For a specific reference, subsequent revisions do not apply.
- Fo... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 3 Definitions, symbols and abbreviations | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 3.1 Definitions | For the purposes of the present document, the terms and definitions given in TR 21.905 [1] and the following apply.
A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1]. |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 3.2 Symbols | For the purposes of the present document, the following symbols apply:
<symbol> <Explanation> |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 3.3 Abbreviations | For the purposes of the present document, the abbreviations given in TR 21.905 [1] and the following apply.
An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 [1]. |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 4 Background | The present document is a technical report for Dual Connectivity (EN-DC) of 1 LTE band (1DL/1UL) and 1 NR band (1DL/1UL) under Rel-16 time frame. It covers both the UE and BS side. The document is divided in two different parts:
- General part: this part covers BS and UE specific which is band combination independent.... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 4.1 TR Maintenance | A single company is responsible for introducing all approved TPs in the current TR, i.e. TR editor. However, it is the responsibility of the contact person of each band combination to ensure that the TPs related to the band combination have been implemented. |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 5 EN-DC of 1 LTE band (1DL/1UL) and 1 NR band (1DL/1UL): General Part | 5.1 Maximum Sensitivity Degradation (MSD) analysis
5.1.1 Inter-band EN-DC within FR1
For each inter-band DC band combination, sensitivity degradation is allowed for a band if it is impacted by UL harmonic interference, harmonic mixing, close proximity of bands, cross band isolation, and intermodulation interference fr... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6 EN-DC of 1 LTE band (1DL/1UL) and 1 NR band: Specific Band Combination Part | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1 Inter-band EN-DC within FR1 | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1 DC_5_n79 | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1.1 Operating bands for DC | Table 6.1.1..1-1: DC band combination of 1 LTE band + 1 NR band
EN-DC band
E-UTRA Band
NR Band
Single UL allowed
DC_5_n79
5
n79
No |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1.2 Configuration for DC | Table 6.1.2.2-1: Inter-band EN-DC configurations of 1 LTE band + 1 NR band
EN-DC
configuration
Uplink EN-DC
configuration
(NOTE 1)
E-UTRA configuration
NR configuration
DC_5A_n79A
DC_5A_n79A
5A
n79A |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1.3 Maximum output power for DC | Table 6.1.1.3-1: Maximum output power for inter-band EN-DC of 1 LTE band + 1 NR band
DC configuration
Power class 3
(dBm)
Tolerance
(dB)
DC_5A_n79A
23
+2/-3 |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1.4 Spurious emission band UE co-existence for DC | Table 6.1.1.4-1: Spurious emissions for inter-band EN-DC of 1 LTE band + 1 NR band
E-UTRA and NR DC Configuration
Spurious emission
Protected band
Frequency range (MHz)
Maximum Level (dBm)
MBW (MHz)
NOTE
DC_5A_n79A
Bands 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 50, 51... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.1.5 MSD analysis for DC | For 2UL/2DL UE coexistence study 2nd, 3rd, 4th and 5th order harmonics and 2nd, 3rd, 4th and 5th order intermodulation products were calculated and presented in Table 6.1.1.5-1
Table 6.1.1.5-1: Harmonic and IMD analysis
UE UL carriers
fx_low
fx_high
fy_low
fy_high
UL frequency (MHz)
824
849
4400
5000
2nd harmonics freq... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2 DC_3_n41 | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2.1 Operating bands for DC | Table 6.1.2.1-1: Band combinations for EN-DC (two bands)
EN-DC band
E-UTRA Band
NR Band
Single UL allowed
DC_3_n41
3
n41
No |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2.2 Configuration for DC | Table 6.1.2.2-1: Inter-band EN-DC configurations (two bands)
EN-DC
configuration
Uplink EN-DC
configuration
E-UTRA configuration
NR configuration
DC_3A_n41A
DC_3A_n41A
3A
n41A |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2.3 Maximum output power for DC | Table 6.1.2.3-1: Maximum output power for inter-band EN-DC (two bands)
DC configuration
Power class 3
(dBm)
Tolerance
(dB)
DC_3A_n41A
23
+/-2 |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2.4 Spurious emission band UE co-existence for DC | Interference analysis for DC_3A_n41A is shown in Table 6.1.2.4-1.
Table 6.1.2.4-1: Harmonics and IMD products for DC_3A_n41A
UE UL carriers
fx_low
fx_high
fy_low
fy_high
2nd harmonics frequency limits
2*fx_low
2*fx_high
2* fy_low
2* fy_high
3420
3570
4992
5380
3rd harmonics frequency limits
3*fx_low
3*fx_high
3* fy_low... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.2.5 MSD for DC | Reference sensitivity exceptions due to cross band isolation are specified for DC_3A_n41A in Table 6.1.2.5-1 with uplink configuration specified in Table 6.1.2.5-2.
Table 6.1.2.5-1: Reference sensitivity exceptions due to cross band isolation
EN-DC configuration
UL band
DL band
MSD
5 MHz
(dB)
10 MHz
(dB)
15 MHz
(dB)
20... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3 DC_3_n1, DC_3-3_n1 | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3.1 Operating bands for DC | Table 6.1.3.1-1: DC band combination of 1 LTE band + 1 NR band
EN-DC band
E-UTRA Band
NR Band
Single UL allowed
DC_3_n1
3
n1
Yes
DC_3-3_n1
CA_3-3
n1
Yes |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3.2 Configuration for DC | Table 6.1.3.2-1: Inter-band EN-DC configurations of 1 LTE band + 1 NR band
EN-DC
configuration
Uplink EN-DC
configuration
(NOTE 1)
E-UTRA configuration
NR configuration
DC_3A_n1A
DC_3A_n1A
3A
n1A
DC_3C_n1A
DC_3A_n1A
DC_3C_n1A
3C
n1A
DC_3A-3A_n1A
DC_3A_n1A
CA_3A-3A
n1A |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3.3 Maximum output power for DC | Table 6.1.3.3-1: Maximum output power for inter-band EN-DC of 1 LTE band + 1 NR band
DC configuration
Power class 3
(dBm)
Tolerance
(dB)
DC_3A_n1A
DC_3C_n1A
23
+2/-3 |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3.4 Spurious emission band UE co-existence for DC | Table 6.1.3.4-1: Spurious emissions for inter-band EN-DC of 1 LTE band + 1 NR band
E-UTRA and NR DC Configuration
Spurious emission
Protected band
Frequency range (MHz)
Maximum Level (dBm)
MBW (MHz)
NOTE
DC_3A_n1A
E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 50, 51, 65, 67, 72, 73... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.3.5 MSD analysis for DC | For 2UL/2DL UE coexistence study 2nd, 3rd, 4th and 5th order harmonics and 2nd, 3rd, 4th and 5th order intermodulation products were calculated and presented in Table 6.1.3.5-1
Table 6.1.3.5-1: Harmonic and IMD analysis
UE UL carriers
fx_low
fx_high
fy_low
fy_high
UL frequency (MHz)
1710
1785
1920
1980
2nd harmonics fr... |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.4 DC_7_n77, DC_7-7_n77 | |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.4.1 Operating bands for DC | Table 6.1.4.1-1: DC band combination of 1 LTE band + 1 NR band
EN-DC band
E-UTRA Band
NR Band
Single UL allowed
DC_7_n773
7
n77
No
DC_7-7_n773
CA_7-7
n77
No
NOTE 3: Applicable for UE supporting inter-band carrier aggregation with mandatory simultaneous Rx/Tx capability |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.4.2 Configuration for DC | Table 6.1.4.2-1: Inter-band EN-DC configurations of 1 LTE band + 1 NR band
EN-DC
configuration
Uplink EN-DC
configuration
(NOTE 1)
E-UTRA configuration
NR configuration
DC_7A_n77A
DC_7A_n77A
7A
n77A
DC_7A-7A_n77A
DC_7A_n77A
CA_7A-7A
n77A |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.4.3 Maximum output power for DC | Table 6.1.4.3-1: Maximum output power for inter-band EN-DC of 1 LTE band + 1 NR band
DC configuration
Power class 3
(dBm)
Tolerance
(dB)
DC_7A_n77A
23
+2/-3 |
60867663a50f38ca462c3e99d4cdca20 | 37.716-11-11 | 6.1.4.4 Spurious emission band UE co-existence for DC | Table 6.1.4.4-1: Spurious emissions for inter-band EN-DC of 1 LTE band + 1 NR band
E-UTRA and NR DC Configuration
Spurious emission
Protected band
Frequency range (MHz)
Maximum Level (dBm)
MBW (MHz)
NOTE
DC_7A_n77A
E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 40, 50, 51, 65, 66, ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.