hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.12.4.2 Test Procedure | 1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2. The RF parameters for Test 1 are set up according to tables 8.7.12.5.2 and 8.7.12. 5.3.
2) If compressed mode is required, SS shall transmit PHYSICAL CHANNEL RECONFIGURATION message (compressed gaps). Otherwise, Go to Step4.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.12.5 Test requirements | Table 8.7.12.5.2 and table 8.7.12.5.3 define the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.12.5.4 in each test shall be more than 90% with a confidence level of 95%.
Table 8.7.12.5.1: Void
Table 8.7.12.5.2: UTRAN ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13 E-UTRAN TDD RSRQ absolute accuracy (CELL_DCH) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.1 Definition and applicability | The absolute accuracy of RSRQ is defined as the RSRQ measured from a cell that has different carrier frequency from the serving cell.
The E-UTRAN TDD RSRQ absolute accuracy measurement is used for handover between UTRAN FDD and E-UTRAN TDD.
The requirements and this test apply to the combined UTRAN FDD and E-UTRAN TDD ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.2 Minimum Requirements | The accuracy requirements for E-UTRA RSRQ measurements in CELL_DCH state shall be the same as the inter-frequency RSRQ accuracy requirements in3GPP TS36.133[34], as follows:
- Cell specific reference signals are transmitted either from one, two or four antenna ports.
- Conditions defined in TS 36.101 [2] clause 7.3 for... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.3 Test purpose | The purpose of this test is to verify that the E-UTRAN TDD RSRQ measurement accuracy in CELL_DCH state, for UE that needs compressed mode to perform E-UTRAN TDD measurements, is within the specified limits. This measurement is for UTRAN FDD to E-UTRAN TDD handover evaluation. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.4.1 Initial conditions | Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table K.2 in Annex K.
In the test in Cell_DCH state compressed mode with purpose "E-UTRAN TDD RSRQ Measurement" is applied to measure on E-UTRAN TDD. The compressed mode pattern repeats every 80 ms and uses ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.4.2 Test Procedure | 1) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.2. The RF parameters for Test 1 are set up according to tables 8.7.13.5.2 and 8.7.13.5.3.
2) If compressed mode is required, SS shall transmit PHYSICAL CHANNEL RECONFIGURATION message(compressed gaps). Otherwise, Go to Step4.
3... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.7.13.5 Test requirements | Table 8.7.13.5.2 and table 8.7.13.5.3 define the primary level settings including test tolerances for all tests.
For the test to pass, the ratio of successful reported values according to table 8.7.13.5.4 in each test shall be more than 90% with a confidence level of 95%.
Table 8.7.13.5.1: Void
Table 8.7.13.5.2: UTRAN ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.1 General | The performance requirements for the UE in this clause are specified for the measurement channels specified in Annex C, the propagation conditions specified in Annex D and the Down link Physical channels specified in Annex E. Unless stated otherwise, DL power control is OFF.
Unless otherwise stated the performance requ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.2 Demodulation of HS-DSCH (Fixed Reference Channel) | The minimum performance requirement for a particular UE belonging to one of the HS-DSCH categories 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 or 12 are determined according to Table 9.2.1.
The performance requirements for a particular UE belonging to one of the HS-DSCH categories 1, 2, 3, 4, 5, 6, 7, 8, 9 or 10 and supporting t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.2.1 Single Link Performance | The test cases in the following sections 9.2.1A to 9.2.1I define the Single Link Performance tests for the different H-Sets for the different HS-DSCH Categories as defined in tables 9.2.1, 9.2.2, 9.2.3 and 9.2.3A.
9.2.1A Single Link Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.1A.1 Definition... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.2.2 Open Loop Diversity Performance | The test cases in the following sections 9.2.2A to 9.2.2D define the Open Loop Diversity Performance tests for the different H-Sets for the different HS-DSCH Categories as defined in tables 9.2.1, 9.2.2 and 9.2.3.
9.2.2A Open Loop Diversity Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.2A.1 De... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.2.3 Closed Loop Diversity Performance | The test cases in the following sections 9.2.3A to 9.2.3D define the Closed Loop Diversity Performance tests for the different H-Sets for the different HS-DSCH Categories as defined in tables 9.2.1, 9.2.2 and 9.2.3.
9.2.3A Closed Loop Diversity Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.3A.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.2.4 MIMO Performance | The test case in section 9.2.4A defines the MIMO Performance test for the Fixed Reference Channel (FRC) H-Set 9.
9.2.4A MIMO Performance - Fixed Reference Channel (FRC) H-Set 9
9.2.4A.1 Definition and applicability
The MIMO performance of the High Speed Physical Downlink Shared Channel (HS-DSCH) in multi-path fading en... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3 Reporting of Channel Quality Indicator | The propagation conditions for this subclause are defined in table D.2.2.1B for non-MIMO operation under fading conditions, in subclause D.2.9.1 for MIMO operation under single stream conditions, and in subclause D.2.9.2 for MIMO operation under dual stream conditions.
For the cases in this subclause where CQI reportin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1 Single Link Performance - AWGN Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.1 Definition and applicability | The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 5 for all types of UTRA for the FDD UE that support HSDPA UE... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.2 Minimum requirements | For the parameters specified in Table 9.3.1.1, and using the downlink physical channels specified in table E.5.1 for HSDPA categories 1-8, 11 and 12 or in Table E.5.1A for other HSDPA categories the reported CQI value shall be in the range of +/-2 of the reported median more than 90% of the time. If the HS-PDSCH BLER ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.3 Test purpose | To verify that the variance of the CQI reports when using TF based on CQI 16 is within the limits defined and that a BLER of 10% falls between the TF based on Median CQI-1 and the TF based on Median CQI TF or between the TF based on Median CQI and the TF based on Median CQI+2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS and an AWGN noise source to the UE antenna connector as shown in figure A.9.
2. Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is sent... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with levels according to table E.5.0, and with the following exceptions in the RADIO BEARER SETUP message.
Table 9.3.1.2: Contents of RADIO BEARER SETUP message: AM or UM (HSDPA)
Information Element
Value/Remark
Downlink HS-P... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.1.5 Test Requirements | The pass fail decision is as specified in the test procedure in clause 9.3.1.4.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test.
9.3.1A Single Link Performance - AWGN Propagation Conditions, 64QAM
9.3.1A.1 De... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2 Single Link Performance - Fading Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.1 Definition and applicability | The reporting accuracy of the channel quality indicator (CQI) under fading environments is determined by the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 5 for all types of UTRA for the FDD UE that support HSDPA UE capability categorie... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.2 Minimum requirements | For the parameters specified in Table 9.3.2.1, and using the downlink physical channels specified in table E.5.1, the requirements are specified in terms of maximum BLERs at particular reported CQIs when transmitting a fixed transport format given by the CQI median as shown in Table 9.3.2.2. The BLER at a particular re... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.3 Test purpose | To verify that when using the TF based on the Median CQI that the BLER for blocks associated with CQI reports of Median CQI is 60% and that the BLER for blocks associated with CQI reports of Median CQI+3 is 15%. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.10.
2) Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with levels according to table E.5.0, and with the following exceptions in the RADIO BEARER SETUP message. Set test conditions according to test 1 in table 9.3.2.1. The configuration of the downlink channels is defined in tab... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.2.5 Test Requirements | The measured BLER shall not exceed values specified in table 9.3.2.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test.
9.3.2A Single Link Performance - Fading Propagation Conditions, DC-HSDPA requirements
9.3.2... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3 Open Loop Diversity Performance - AWGN Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.1 Definition and applicability | The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 6 and later releases for all types of UTRA for the FDD UE th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.2 Minimum requirements | For the parameters specified in Table 9.3.3.1, and using the downlink physical channels specified in table E.5.2 the reported CQI value shall be in the range of +/-2 of the reported median more than 90% of the time. If the HS-PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.3 Test purpose | To verify that the variance of the CQI reports when using TF based on CQI 16 is within the limits defined and that a BLER of 10% falls between the TF based on Median CQI-1 and the TF based on Median CQI TF or between the TF based on Median CQI and the TF based on Median CQI+2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS and an AWGN noise source to the UE antenna connector as shown in figure A.12a.
2. Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with the exceptions for information elements listed in table 9.3.3.2, with levels according to table E.5.0.
2) Set test conditions according to test 1 according table 9.3.3.1. The configuration of the downlink channels is def... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.3.5 Test Requirements | The pass fail decision is as specified in the test procedure in clause 9.3.3.4.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4 Open Loop Diversity Performance - Fading Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.1 Definition and applicability | The reporting accuracy of the channel quality indicator (CQI) under fading environments is determined by the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 6 and later releases for all types of UTRA for the FDD UE that support HSDPA UE c... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.2 Minimum requirements | For the parameters specified in Table 9.3.4.1, and using the downlink physical channels specified in table E.5.2, the requirements are specified in terms of maximum BLERs at particular reported CQIs when transmitting a fixed transport format given by the CQI median as shown in Table 9.3.4.2.. The BLER at a particular r... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.3 Test purpose | To verify that when using the TF based on the Median CQI that the BLER for blocks associated with CQI reports of Median CQI is 60% and that the BLER for blocks associated with CQI reports of Median CQI+3 is 15%. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.12.
2) Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with the exceptions for information elements listed in table 9.3.4.3, with levels according to table E.5.0. Set test conditions according to test 1 according table 9.3.4.1. The configuration of the downlink channels is define... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.4.5 Test Requirements | The measured BLER shall not exceed values specified in table 9.3.4.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5 Closed Loop Diversity Performance - AWGN Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.1 Definition and applicability | The reporting accuracy of channel quality indicator (CQI) under AWGN environments is determined by the reporting variance and the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 6 and later releases for all types of UTRA for the FDD UE th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.2 Minimum requirements | For the parameters specified in Table 9.3.5.1, and using the downlink physical channels specified in table E.5.3 the reported CQI value shall be in the range of +/-2 of the reported median more than 90% of the time. If the HS-PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.3 Test purpose | To verify that the variance of the CQI reports when using TF based on CQI 16 is within the limits defined and that a BLER of 10% falls between the TF based on Median CQI-1 and the TF based on Median CQI TF or between the TF based on Median CQI and the TF based on Median CQI+2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS and an AWGN noise source to the UE antenna connector as shown in figure A.12a.
2. Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, Nack or DTX) new data is se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with the exceptions for information elements listed in table 9.3.5.2, with levels according to table E.5.0.
2) Set test conditions according to test 1 according table 9.3.5.1. The configuration of the downlink channels is def... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.5.5 Test Requirements | The pass fail decision is as specified in the test procedure in clause 9.3.5.4.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6 Closed Loop Diversity Performance - Fading Propagation Conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.1 Definition and applicability | The reporting accuracy of the channel quality indicator (CQI) under fading environments is determined by the BLER performance using the transport format indicated by the reported CQI median.
The requirements and this test apply to Release 6 and later releases for all types of UTRA for the FDD UE that support HSDPA UE c... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.2 Minimum requirements | For the parameters specified in Table 9.3.6.1, and using the downlink physical channels specified in table E.5.3, the requirements are specified in terms of maximum BLERs at particular reported CQIs when transmitting a fixed transport format given by the CQI median as shown in Table 9.3.6.2. The BLER at a particular re... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.3 Test purpose | To verify that when using the TF based on the Median CQI that the BLER for blocks associated with CQI reports of Median CQI is 60% and that the BLER for blocks associated with CQI reports of Median CQI+3 is 15%. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.12.
2) Set Ack/Nack handling at the SS such that regardless of the response from the UE (Ack, ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.4.2 Procedure | 1) Set up an HSDPA call with looping back 12.2kbps RMC according to TS 34.108 [3] clause 7.3.6 with the exceptions for information elements listed in table 9.3.6.3, with levels according to table E.5.0. Set test conditions according to test 1 according table 9.3.6.1. The configuration of the downlink channels is define... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.6.5 Test Requirements | The measured BLER shall not exceed values specified in table 9.3.6.2.
There are no parameters in the test setup or measurement process whose variation impacts the results so there are no applicable test tolerances for this test. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.3.7 MIMO Performance - Reporting of Channel Quality Indicator | The test cases in this section define the MIMO Performance test for Reporting of Channel Quality Indicator.
9.3.7A MIMO Single Stream Fading Conditions
9.3.7A.1 Definition and applicability
The minimum performance requirements of channel quality indicator (CQI) reporting under MIMO single stream conditions are defined ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4 HS-SCCH Detection Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1 Single Link Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.1 Definition and applicability | The detection performance of the HS-SCCH is determined by the probability of event Em, which is declared when the UE is signalled on HS-SCCH-1, but DTX is observed in the corresponding HS-DPCCH ACK/NACK field. The probability of event Em is denoted P(Em).
The requirements and this test apply to all types of UTRA for FD... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.2 Minimum requirements | For the parameters specified in Table 9.4.1.1, for each value of HS-SCCH-1 Ec/Ior specified in Table 9.4.1.2 the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em).
Table 9.4.1.1: Test parameters for HS-SCCH detection - single link
Parameter
Unit
Test 1
Test 2
Test 3
dBm/3.84 MHz
-... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.3 Test purpose | To verify that P(Em) does not exceed the limit in table 9.4.1.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.21 for UEs that support receive diversity or figure A.10 for UEs that do not support receive d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.4.2 Procedure | 1. The UE is switched on.
2. Set up a HSDPA connection with looping back 12.2kbps RMC according to the generic HSDPA set-up procedure specified in TS 34.108 [3] sub clause 7.3.6 with levels according to table E.5.0.
3. Once the HSDPA connection is setup, change levels according to Table E.5.4 and start transmitting HSD... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.1.5 Test Requirements | Tables 9.4.1.3. and 9.4.1.4 define the primary level settings including test tolerance and test parameters for relevant tests. The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in table 9.4.1.4. The pass/fail decision is done according to Annex F.6.1.
Table 9.4.1.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2 Open Loop Diversity Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.1 Definition and applicability | The detection performance of the HS-SCCH is determined by the probability of event Em, which is declared when the UE is signalled on HS-SCCH-1, but DTX is observed in the corresponding HS-DPCCH ACK/NACK field. The probability of event Em is denoted P(Em).
The requirements and this test apply for Release 6 and later to ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.2 Minimum requirements | For the test parameters specified in Table 9.4.2.1, for each value of HS-SCCH-1 Ec/Ior specified in Table 9.4.2.2 the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em).
Table 9.4.2.1: Test parameters for HS-SCCH detection - open loop diversity
Parameter
Unit
Test 1
Test 2
Test 3
d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.3 Test purpose | To verify that P(Em) does not exceed the limit in table 9.4.2.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect SS, multipath fading simulators and AWGN noise sources to the UE antenna connector as shown in figure A.22 for UEs that support receive diversity or figure A.12 for UEs that do not support receive di... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.4.2 Procedure | 1. The UE is switched on.
2. Set up a HSDPA connection with looping back 12.2kbps RMC according to the generic HSDPA set-up procedure specified in TS 34.108 [3] sub clause 7.3.6 with the exceptions for information elements listed in table 9.4.2.3, with levels according to table E.5.0.
3. Once the HSDPA connection is se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.2.5 Test Requirements | Tables 9.4.2.4. and 9.4.2.5 define the primary level settings including test tolerance and test parameters for relevant tests. The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in table 9.4.2.5. The pass/fail decision is done according to Annex F.6.1.
Table 9.4.2.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3 HS-SCCH Type 3 Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.1 Definition and applicability | The detection performance of the HS-SCCH is determined by the probability of event Em, which is declared when the UE is signalled on HS-SCCH-1, but DTX is observed in the corresponding HS-DPCCH ACK/NACK field. The probability of event Em is denoted P(Em).
The requirements and this test apply for Release 7 and later for... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.2 Minimum requirements | For the test parameters specified in Table 9.4.3.1 with the downlink physical channel setup in Table E.5.4A, for each value of HS-SCCH-1 Ec/Ior specified in Table 9.4.3.2 and Table 9.4.3.3 the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em). The requirements in Table 9.4.3.2 and... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.3 Test purpose | To verify that P(Em) does not exceed the limit in table 9.4.3.2 for the single transport block case, and in table 9.4.3.3 for the dual transport block case. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.22.
2) Set the test parameters for test 1-4 as specified in table 9.4.3.5. Setup fading simula... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.4.2 Procedure | 1. The UE is switched on.
2. Set up a HSDPA connection with looping back 12.2kbps RMC according to the generic HSDPA set-up procedure specified in TS 34.108 [3] sub clause 7.3.6 with the exceptions for information elements listed in table 9.4.3.4, with levels according to table E.5.0.
3. Once the HSDPA connection is se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.3.5 Test Requirements | Tables 9.4.3.5 to 9.4.3.7 define the primary level settings including test tolerance and test parameters for relevant tests. The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in table 9.4.3.6 for single transport block case and the specified value in table 9.4.3.7... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4 HS-SCCH Type 3 Performance for MIMO only with single-stream restriction | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.1 Definition and applicability | The detection performance of the HS-SCCH for MIMO only with single-stream restriction is determined by the probability of event Em, which is declared when the UE is signalled on HS-SCCH-1, but DTX is observed in the corresponding HS-DPCCH ACK/NACK field. The probability of event Em is denoted P(Em).
The requirements an... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.2 Minimum requirements | For the test parameters specified in Table 9.4.4.1 with the downlink physical channel setup in Table E.5.4A, for each value of HS-SCCH-1 Ec/Ior specified in Table 9.4.4.2 the measured P(Em) shall be less than or equal to the corresponding specified value of P(Em). The requirements in Table 9.4.4.2 assume STTD is enable... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.3 Test purpose | To verify that P(Em) does not exceed the limit in Table 9.4.4.2 for the single transport block case. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.22 for UEs that support receive diversity or figure A.12 for UEs that do not support receive d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.4.2 Procedure | 1. The UE is switched on.
2. Set up a HSDPA connection with looping back 12.2kbps RMC according to the generic HSDPA set-up procedure specified in TS 34.108 [3] sub clause 7.3.6 with the exceptions for information elements listed in Table 9.4.4.4, with levels according to Table E.5.0.
3. Once the HSDPA connection is se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.4.4.5 Test Requirements | Tables 9.4.4.5 to 9.4.4.6 define the primary level settings including test tolerance and test parameters for relevant tests. The probability of event Em denoted as P(Em) (test procedure step 3) shall not exceed the specified value in Table 9.4.4.6 for single transport block case. The pass/fail decision is done accordin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 9.5 HS-SCCH-less demodulation of HS-DSCH (Fixed Reference Channel) | During the Fixed Reference Channel tests the behaviour of the Node-B emulator in response to the ACK/NACK signalling field of the HS-DPCCH is specified in Table 9.2.4.
Performance requirements in this section assume sufficient power allocation to HS-SCCH_1, so that the probability of detection failure, when the HS-SCCH... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.