hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.1.1 Transport channel parameters of BMC RAB and SRBs for CCCH, SRB for DCCH, and SRB for BCCH | Higher layer
RAB/signalling RB
SRB#1
SRB#2
SRB#3
SRB#4
SRB#5
SRB#6
RAB#30
User of Radio Bearer
RRC
RRC
RRC
NAS_DT
High prio
NAS_DT
Low prio
RRC
-
RLC
Logical channel type
CCCH
DCCH
DCCH
DCCH
DCCH
BCCH
CTCH
RLC mode
UM
UM
AM
AM
AM
TM
UM
Payload sizes, bit
152
136 or 120*
128
128
128
166
152
Max data rate, bps
45600
4080... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.1.2 TFCS | TFCS size
4
TFCS
(BMC RAB and SRBs for CCCH/DCCH/BCCH) = TF0, TF1, TF2, TF3 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.1.3 Physical channel parameters | SCCPCH
DTX position
Flexible
Spreading factor
64
Number of TFCI bits/slot
8
Number of Pilot bits/slot
0
Number of data bits/slot
72
Number of data bits/frame
1080 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2 General BMC message reception | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1 UE in RRC Idle mode | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of certain CBS message contents carried with certain activated CB message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1.2 Conformance requirement | A UE supporting Cell Broadcast Services shall be capable to receive BMC messages in the RRC Idle mode.
Reference(s)
TS 25.324 clause 9.1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1.3 Test purpose | To verify, that a BMC configuration for a UE is able to receive activated CBS messages when in RRC Idle mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1.4 Method of test | Initial conditions
UE is in RRC Idle mode; BMC entity is established
SS: 1 cell,
NOTE: The CB message ID stored on the SIM shall be known for this test (parameter for CBS PDU's). The CBS data type shall be allocated and activated in the UE.
Related ICS/IXIT Statement(s)
Support of BMC – Yes/No
Support of PS – Yes/No
IC... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.1.5 Test requirements | The UE shall store and decode a received activated CBS message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2 UE in RRC Connected mode, state CELL_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of certain CBS message contents carried with certain activated CB message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2.2 Conformance requirement | A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages (...) in CELL_PCH RRC-state of Connected mode.
Reference(s)
TS 25.324 clause 9.1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2.3 Test purpose | To verify, that a BMC configuration for a UE is able to receive activated CBS messages when in RRC Connected mode, state CELL_PCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2.4 Method of test | Initial conditions
UE is in Connected mode state CELL_PCH; BMC entity is established
SS: 1 cell,
NOTE: The CB message ID stored on the SIM shall be known for this test (parameter for CBS PDU's). The CBS data type shall be allocated and activated in the UE.
Related ICS/IXIT Statement(s)
ICS:
Support of BMC – Yes/No
Supp... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.2.5 Test requirements | The UE shall store and decode a received activated CBS message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3 UE in RRC Connected mode, state URA_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of certain CBS message contents carried with certain activated CB message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3.2 Conformance requirement | A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages (...) in CELL_PCH and URA_PCH RRC-state of Connected mode.
Reference(s)
TS 25.324 clause 9.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3.3 Test purpose | To verify, that a BMC configuration for a UE is able to receive activated CBS messages when in RRC Connected mode, state URA_PCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3.4 Method of test | Initial conditions
UE is in Connected mode state URA_PCH; BMC entity is established.
SS: 1 cell,
NOTE: The CB41 message ID stored on the SIM shall be known for this test (parameter for CBS41 PDU's). The CBS41 data type shall be allocated and activated in the UE.
Related ICS/IXIT Statement(s)
ICS:
Support of BMC – Yes/N... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.3.5 Test requirements | The UE shall store and decode a received activated CBS message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4 UE in RRC Idle mode (ANSI-41 CB data) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) for ANSI-41 CB data as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of a certain CBS41 message content carried with certain activated CB41 message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4.2 Conformance requirement | A UE supporting Cell Broadcast Services shall be capable to receive BMC messages in RRC Idle mode. (…)BMC messages are identified: (…), CBS41 Message
Reference(s)
TS 25.324 clause 9.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4.3 Test purpose | To verify, that a BMC configuration supporting ANSI-41 CB Data is able to receive activated CBS41 messages when in RRC Idle mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4.4 Method of test | Initial conditions
UE is in RRC Idle mode; BMC entity is established.
SS: 1 cell,
NOTE: The CB message ID stored on the SIM shall be known for this test (parameter for CBS41 PDU's). The CBS41 data type shall be allocated and activated in the UE.
Related ICS/IXIT Statement(s)
ICS:
Support of BMC – Yes/No
Support of PS –... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.4.5 Test requirements | The UE shall store and decode a received activated CBS41 message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5 UE in RRC Connected mode, state CELL_PCH (ANSI-41 CB data) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) for ANSI-41 CB data as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of certain CBS41 message contents carried with certain activated CB41 message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5.2 Conformance requirement | A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages (...) in CELL_PCH RRC-state of Connected mode. (…)BMC messages are identified: (…), CBS41 Message.
Reference(s)
TS 25.324 clause 9.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5.3 Test purpose | To verify, that a BMC configuration supporting ANSI-41 CB Data is able to receive activated CBS41 messages when in RRC Connected mode, state CELL_PCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5.4 Method of test | Initial conditions
UE is in Connected mode state CELL_PCH; BMC entity is established.
SS: 1 cell,
NOTE: The CB41 message ID stored on the SIM shall be known for this test (parameter for CBS41 PDU's). The CBS41 data type shall be allocated and activated in the UE.
Related ICS/IXIT Statement(s)
ICS:
Support of BMC – Yes/... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.5.5 Test requirements | The UE shall store and decode a received activated CBS41 message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.6 UE in RRC Connected mode, state URA_PCH (ANSI-41 CB data) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.6.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) for ANSI-41 CB data as a type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of a certain CBS41 message content carried with certain activated CB41 message types in a clear way on UE side. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.6.2 Conformance requirement | A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages (...) in URA_PCH RRC-state of Connected mode. (…)BMC messages are identified: (…), CBS41 Message.
Reference(s)
TS 25.324 clause 9.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.6.3 Test purpose | To verify, that a BMC configuration supporting ANSI-41 CB Data is able to receive activated CBS41 messages when in RRC Connected mode, state URA_PCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.2.6.5 Test requirements | The UE shall store and decode a received activated CBS41 message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3 BMC message reception procedure | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1 Reception of certain CBS message types | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1.1 Definition and applicability | Applicable only for a UE supporting Cell Broadcast Services (CBS) as type of Broadcast/Multicast Services.
It shall be possible to indicate the reception of two different CBS message contents carried with different activated CB message types in a clear way on UE side.
It shall be possible to activate/deactivate the CBS... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1.2 Conformance requirement | A UE supporting Cell Broadcast Service (CBS) shall be capable to receive BMC messages in RRC Idle mode.
The BMC entity on UE side evaluates received BMC Schedule Messages and takes decisions which BMC messages are received.
If not otherwise requested by upper layers, only those CB messages received in BMC CBS Messages ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1.3 Test purpose | 1. To verify, that a UE supporting CBS ignores a deactivated CBS message type which has been broadcasted by SS.
2. To verify, that a UE only stores Serial Numbers of a newly transmitted CBS messages. This shall be verified by indication of a received CBS message with changed Serial Number as indication for the storage ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1.4 Method of test | Initial conditions
UE is in RRC Idle mode.
SS: 1 cell,
NOTE: The CB message ID stored on the SIM shall be known for this test (as parameter for the CBS message PDU). The CBS data type shall be allocated and in the UE. It shall be possible to activate/deactivate such CBS data type.
Related ICS/IXIT Statement(s)
ICS:
Sup... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.4.3.1.5 Test requirements | After having received the CB-Data 1 message (step 4), the UE shall store the Serial Number of this message and indicate the reception of the CBS message as described by the manufacturer.
After CB-Data 2 message was newly broadcasted (step 10), the UE shall not indicate the reception for the deactivated CBS message (CB-... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1 RRC Connection Management Procedure | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1 Paging | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1 Paging for Connection in idle mode | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in [25.304] and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a UE in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1.3 Test purpose | 1) For the CS domain
To confirm that the UE establishes an RRC connection after it receives a PAGING TYPE 1 message which includes IE "UE identity"(in IE "Paging Record") set to the IMSI of the UE, and responds with a correct INITIAL DIRECT TRANSFER message.
2) For the PS domain
To confirm that the UE establishes an RR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: MM-IDLE state and Updated update status with no TMSI (if CS supported)
GMM-Registered with a P-TMSI assigned (if PS supported)
the UE shall have an IMSI.
Test Procedure
SS transmits SYSTEM INFORMATION BLOCK TYPE 1 or 13 messages, depending on the CN type supported by the U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.1.5 Test requirement | After step 2 the UE shall not respond to PAGING TYPE 1 message sent in step 2.
After step 3 the UE shall transmit RRC CONNECTION REQUEST message on the uplink CCCH.
After step 5 the UE shall have an RRC connection based on dedicated physical channel resources and transmit an RRC CONNECTION SETUP COMPLETE message and IN... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2 Paging for Connection in connected mode (CELL_PCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in [25.304] and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a UE in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2.3 Test purpose | To confirm that the UE enters the CELL_FACH state after it receives a PAGING TYPE 1 message which indicates that the paging has originated from UTRAN. To verify that the UE performs cell update procedure after entering the CELL_FACH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CELL_PCH state (state 6-12) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI already assigned by the SS.
Test Procedure
SS transmits SYSTEM INFORMATION BLOCK TYPE 1 or 13 messages, depending on the CN type supported by the UE. The SS transmits a PAGING TYPE 1 m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.2.5 Test requirement | After step 2 the UE shall not respond to the PAGING TYPE 1 message sent in step 2.
After step 3 the UE shall not respond to the PAGING TYPE 1 message sent in step 3.
After step 4 the UE shall enter the CELL FACH state and send a CELL UPDATE message with "Cell Update Cause" IE set to "paging response".
After step 6 the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3 Paging for Connection in connected mode (URA_PCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in [25.304] and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a UE in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3.3 Test purpose | To confirm that the UE enters the CELL_FACH state after it receives a PAGING TYPE 1 message in which the IE "Used paging identity" is set to "UTRAN identity", and the UE takes the U-RNTI value assigned to it in the IE "U-RNTI". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: URA_PCH state (state 6-13) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI assigned by the SS.
Test Procedure
The SS transmits a PAGING TYPE 1 message, which includes an unmatched U-RNTI. The UE does not change its current state. The SS transmits a PAGING TYP... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.3.5 Test requirement | After step 1 the UE shall not respond to the paging.
After step 2 the UE shall enter the CELL FACH state, and transmit CELL UPDATE message to initiate the cell updating procedure with the paging cause set to "paging response".
After step 4 the UE shall be in the CELL_FACH state and shall transmit UTRAN MOBILITY INFORMA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4 Paging for notification of BCCH modification in idle mode | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4.2 Conformance requirement | A UE in idle mode state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in TS 25.304 and depend on the IE "CN domain specific DRX cycle length coefficient".
When the UE receives a PAGING TYPE 1 message, it shall perform the actions ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4.3 Test purpose | To confirm that the UE checks the new value tag of the master information block and reads the updated SYSTEM INFORMATION BLOCK messages after it receives a PAGING TYPE 1 message which includes the IE "BCCH Modification Information". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108 with a CN UE identity, depending on the CN domain(s) supported by the UE.
Test Procedure
The SS transmits a PAGING TYPE 1 message. This message addresses the UE using its (P)TMSI and the "p... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.4.5 Test requirement | After step 1 the UE shall transmit RRC CONNECTION REQUEST messages in response to the PAGING TYPE 1 messages sent in step 1, using an allowed signature according to original IE "Available signature"(FDD) )/ "Available SYNC_UL codes indices "(1.28 Mcps TDD) in SYSTEM INFORMATION BLOCK TYPE 5 / SYSTEM INFORMATION BLOCK T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5 Paging for notification of BCCH modification in connected mode (CELL_PCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5.2 Conformance requirement | A UE in CELL_PCH state shall receive the paging information for all its monitored paging occasions. For a UE in CELL_PCH state, the paging occasions depend also on the IE "UTRAN DRX cycle length coefficient" and the IE "RRC State Indicator", as specified in TS 25.331 subclauses 8.6.3.2 and 8.6.3.3 respectively.
When th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5.3 Test purpose | To confirm that the UE, in addition to any actions caused by the IE "Paging record" occurrences in the PAGING TYPE 1 message, checks the new value tag of the master information block, and read the SYSTEM INFORMATION messages after it receives a PAGING TYPE 1 message which includes the IE "BCCH Modification Information"... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_PCH state (state 6-12) as specified in clause 7.4 of TS 34.108 with valid a U-RNTI assigned to it.
Test Procedure
The SS transmits a PAGING TYPE 1 message on the paging occasions assigned to the UE. The PAGING TYPE 1 message shall include the IE "BCCH Modification In... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.5.5 Test requirement | After step 4 the UE shall transmit a CELL UPDATE message with IE "cell update cause" set to "paging response", using an allowed signature according to modified IE "Available signature"(FDD) )/ " Available SYNC_UL codes indices "(1.28 Mcps TDD)/ "Available Channelisation codes indices " (3.84 Mcps and 7.68 Mcps TDD) in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6 Paging for notification of BCCH modification in connected mode (URA_PCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6.2 Conformance requirement | A UE in URA_PCH state shall receive the paging information for all its monitored paging occasions. For a UE in URA_PCH state, the paging occasions depend also on the IE "UTRAN DRX cycle length coefficient" and the IE "RRC State Indicator", as specified in TS 25.331 subclauses 8.6.3.2 and 8.6.3.3 respectively.
When the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6.3 Test purpose | To confirm that the UE checks the included new value tag of the master information block and reads the relevant SYSTEM INFORMATION block(s) after it receives a PAGING TYPE 1 message which includes the IE "BCCH Modification Information". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH state (state 6-13) as specified in clause 7.4 of TS 34.108 with a valid U-RNTI assigned.
Test Procedure
The SS transmits a PAGING TYPE 1 message on the paging occasions assigned to the UE. The message shall include the IE "BCCH Modification Information" indicating ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.6.5 Test requirement | After step 4, the UE shall transmit a CELL UPDATE message with IE "cell update cause" set to "paging response", using an allowed signature according to modified IE "Available signature"(FDD) )/ "Available SYNC_UL codes indices" (1.28 Mcps TDD) / "Available Channelisation codes indices " (3.84 Mcps and 7.68 Mcps TDD) in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7 Paging for Connection in connected mode (CELL_DCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7.2 Conformance requirement | When the UE receives a PAGING TYPE 2 message, it shall not affect the state of any other ongoing RRC procedures, when not stated otherwise elsewhere.
The UE shall:
1> indicate reception of paging; and
1> forward the IE "Paging cause" and the IE "Paging record type identifier" to upper layers.
…
In the UE, the initial d... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7.3 Test purpose | To confirm that the UE responds to a PAGING TYPE 2 message which includes the IE "Paging Cause" and the IE "Paging Record Type Identifier".
To confirm that the UE responds with a RRC STATUS message after it has received an invalid PAGING TYPE 2 message.
To Page with the Paging Record Type Identifier set to "IMSI", in o... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH state (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108 after executing a location registration and/or attach procedure. The UE has been registered in both CS and PS domains.
Test Procedure
The SS transmits an invalid PAGING TYPE 2 message. UE sha... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.7.5 Test requirement | After step 2 the UE shall respond to the paging message by transmitting RRC STATUS on the DCCH, stating the protocol error as "Information element value not comprehended ".
After step 4 the UE shall respond to the paging message by transmitting an INITIAL DIRECT TRANSFER message on the uplink DCCH.
8.1.1.8 Paging for ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.8.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.8.2 Conformance requirement | When the UE receives a PAGING TYPE 2 message, it shall not affect the state of any other ongoing RRC procedures, when not stated otherwise elsewhere.
The UE shall:
1> indicate reception of paging; and
1> forward the IE "Paging cause" and the IE "Paging record type identifier" to upper layers.
…
In the UE, the initial d... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.8.3 Test purpose | To confirm that the UE responds to a PAGING TYPE 2 message, which includes a matching value for IE "Paging Record Type Identifier". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.8.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_FACH state (state 6-11) as specified in clause 7.4 of TS 34.108. The UE has been registered in both CS and PS domains.
Test Procedure
The SS transmits a PAGING TYPE 2 message. Then the UE shall respond by transmitting an upper layer message to answer this page.
Expec... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.8.5 Test requirement | After step 2 the UE shall respond to the PAGING TYPE 2 message by transmitting an INITIAL DIRECT TRANSFER message on the uplink DCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9 Paging for Connection in idle mode (multiple paging records) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in [25.304] and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a UE in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9.3 Test purpose | 1) For the CS domain
To confirm that the UE establishes an RRC connection after it receives a PAGING TYPE 1 message which contains multiple paging records and includes IE "UE identity"(in IE "Paging Record") set to the IMSI of the UE, and responds with a correct INITIAL DIRECT TRANSFER message.
2) For the PS domain
To ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: MM-IDLE state and Updated update status with no TMSI (if CS supported)
GMM-Registered with a P-TMSI assigned (if PS supported)
the UE shall have an IMSI.
Test Procedure
SS transmits SYSTEM INFORMATION BLOCK TYPE 1 or 13 messages, depending on the CN type supported by the ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.