hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.9.5 Test requirement | After step 3 the UE shall not respond to the PAGING TYPE 1 message sent in step 3.
After step 4 the UE shall transmit an RRC CONNECTION REQUEST message on the uplink CCCH.
After step 6 the UE shall have an RRC connection based on dedicated physical channel resources and transmit an RRC CONNECTION SETUP COMPLETE message... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10 Paging for Connection in connected mode (URA_PCH, multiple paging records) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in [25.304] and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a UE in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10.3 Test purpose | To confirm that the UE enters the CELL_FACH state after it receives a PAGING TYPE 1 message in which the IE "Used paging identity" is set to "UTRAN identity", and the UE takes the U-RNTI value assigned to it in the IE "U-RNTI". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: URA_PCH state (state 6-13) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI assigned by the SS.
Test Procedure
The SS transmits SYSTEM INFORMATION BLOCK TYPE 6 messages with a modified PCH configuration. The SS then transmits a PAGING TYPE 1 message, which inc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.10.5 Test requirement | After steps 2 and 3 the UE shall not respond to the paging.
After steps 4 and 8 the UE shall enter the CELL FACH state, and transmit CELL UPDATE message to initiate the cell updating procedure with the cell update cause set to "paging response".
After steps 6 and 10 the UE shall transmit an UTRAN MOBILITY INFORMATION C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.11 Paging for Connection in idle mode (Shared Network Environment) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.11.1 Definition | This test is only valid for UEs supporting GSM-MAP CN signalling. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.11.2 Conformance requirement | Upon reception of the master information block, the UE shall:
1> if the IE "Multiple PLMN List" is not present in the Master Information Block:
2> consider the IE "PLMN identity" in the Master Information Block as the PLMN identity of the cell.
1> else:
2> consider the PLMN identities in the IE "Multiple PLMN List" as ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.11.3 Test purpose | 1) For the CS domain
To confirm that the UE establishes an RRC connection after it receives a PAGING TYPE 1 message which includes IE "UE identity"(in IE "Paging Record") set to the IMSI of the UE, and responds with a correct INITIAL DIRECT TRANSFER message.
2) For the PS domain
To confirm that the UE establishes an RR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.11.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: MM-IDLE state and Updated update status with no TMSI (if CS supported)
GMM-Registered with a P-TMSI assigned (if PS supported)
the UE shall have an IMSI.
Test Procedure
SS transmits BCCH blocks containing SYSTEM INFORMATION (GSM-MAP). The SS transmits a PAGING TYPE 1 messa... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12 Paging for Connection in connected mode (CELL_PCH) without HS-SCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12.1 Definition and applicability | All UEs which support FDD and HS-PDSCH in CELL_PCH and URA_PCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12.2 Conformance requirement | A UE in idle mode, CELL_PCH state or URA_PCH state shall receive the paging information for all its monitored paging occasions. For an UE in idle mode, the paging occasions are specified in 3GPP TS 25.304 and depend on the IE "CN domain specific DRX cycle length coefficient", as specified in subclause 8.6.3.1a. For a U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12.3 Test purpose | To confirm that the UE enters the CELL_FACH state after it receives an HS-SCCH less PAGING TYPE 1 message on the HS-DSCH which indicates that the paging has originated from UTRAN. To verify that the UE performs cell update procedure after entering the CELL_FACH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CELL_PCH state (state 6-12) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI already assigned and no dedicated H-RNTI assigned by the SS.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports HS-PDSCH in CELL_PCH and URA_PCH
Test Procedure
The SS transm... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.12.5 Test requirement | After step 2 the UE shall not respond to the PAGING TYPE 1 message sent in step 2.
After step 3 the UE shall not respond to the PAGING TYPE 1 message sent in step 3.
After step 4 the UE shall enter the CELL FACH state and send a CELL UPDATE message with "Cell Update Cause" IE set to "paging response" and “HS-PDSCH in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13 ETWS primary and secondary notification without security reception via S-CCPCH in idle mode, URA_PCH and CELL_PCH state / CELL_FACH state | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13.1 Definition and applicability | All UEs which support FDD and ETWS |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13.2 Conformance requirement | Upon modifications of system information blocks using value tags, UTRAN should notify the new value tag for the master information block in the IE "BCCH modification info", transmitted in the following way:
1> to reach UEs in idle mode, and in CELL_PCH state and URA_PCH state with S-CCPCH assigned, the IE "BCCH modific... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13.3 Test purpose | To confirm that UE receives a PAGING TYPE 1 message on the S-CCPCH which indicates ETWS primary notification and then receives a PAGING TYPE 1 message on the S-CCPCH and receives P-CCPCH and S-CCPCH which indicates ETWS secondary notification and UE shall not indicate secondary notification after BCCH is changed. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH state (state 6-13) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI assigned by the SS. UE is configured to receive the CBS data messages.
Specific Message Contents
SYSTEM INFORMATION TYPE 5/ SYSTEM INFORMATION TYPE 5bis / SYSTEM INFORMATION TYPE 6
Use ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.13.5 Test requirement | In step 5, UE shall not indicate the reception of ETWS notification.
In step10, UE shall indicate the reception of CB Data 1
In step14, UE shall not indicate the reception of CB Data 2
In step 25 and 40, UE shall indicate the reception of CB Data before CTCH FALSE, and UE shall not indicate the reception of CB Data aft... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.14 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.15 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.16 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.17 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.18 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19 ETWS primary and secondary notification / Cell reselection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19.1 Definition and applicability | All UEs which support FDD and ETWS |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19.2 Conformance requirement | Upon modifications of system information blocks using value tags, UTRAN should notify the new value tag for the master information block in the IE "BCCH modification info", transmitted in the following way:
1> to reach UEs in idle mode, and in CELL_PCH state and URA_PCH state with S-CCPCH assigned, the IE "BCCH modific... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19.3 Test purpose | To confirm that UE reselects a new cell which does not send ETWS primary/secondary notifications after the reception of ETWS primary/secondary notifications on an old cell and then UE behaviour on the new cell is not affected by the reception of ETWS primary/secondary notifications on an old cell.
To confirm that UE re... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19.4 Method of test | Initial Condition
System Simulator: 2 cells - Cell 1 and 2
UE: URA_PCH state (state 6-13) as specified in clause 7.4 of TS 34.108, with a valid U-RNTI assigned by the SS. UE is configured to receive the CBS data messages.
Specific Message Contents
SYSTEM INFORMATION TYPE 5/ SYSTEM INFORMATION TYPE 5bis / SYSTEM INFORMA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.19.5 Test requirement | In step 4, UE shall indicate the reception of ETWS notification.
In step 6, UE shall not indicate the reception of ETWS notification.
In step14, UE shall indicate the reception of CB Data 1
In step 15c, UE shall transmit the CELL UPDATE message on Cell 2.
In step 17, UE shall indicate the reception of ETWS notification... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20 Paging / EAB active | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20.2 Conformance requirement | - For paging response the mobile station shall evaluate the control information for common access control (as specified in 3GPP TS 44.018 [84], 3GPP TS 44.060 [76], and 3GPP TS 25.331 [23c]), domain specific access control (as specified in 3GPP TS 44.018 [84] and 3GPP TS 25.331 [23c]), and the specific control informat... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20.3 Test purpose | To verify that the UE can respond to paging when EAB is being broadcast and EAB is enabled in the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20.4 Method of test | Initial Condition
System Simulator: 1 cell
UE:
Registered Idle Mode on PS (state 3) in Cell 1 as specified in clause 7.4 of TS 34.108.
An access class x (0-9) is arbitrarily chosen. The USIM is programmed with this access class x.
The UE is equipped with a USIM containing values shown in Table 8.1.1.20-1.
Table 8.1.1.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.1.20.5 Test requirement | At step 3, The UE shall transmit a RRC CONNECTION REQUEST message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2 RRC Connection Establishment | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1 RRC Connection Establishment in CELL_DCH state: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1.2 Conformance requirement | The UE shall initiate the procedure when upper layers in the UE requests the establishment of a signalling connection and the UE is in idle mode (no RRC connection exists).
Upon initiation of the procedure, the UE shall:
…
1> set the contents of the RRC CONNECTION REQUEST message according to TS 25.331 subclause 8.1.3.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1.3 Test purpose | 1. To confirm that the UE leaves the Idle Mode and correctly establishes signalling radio bearers on the DCCH.
2. To confirm that the UE indicates the requested UE radio access capabilities and UE system specific capabilities (may be used by UTRAN e.g. to configure inter RAT- measurements).
3. To confirm that the UE do... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE transmits an RRC CONNECTION REQUEST message to the SS on the uplink CCCH by attempting to make an outgoing call. Af... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.1.5 Test requirement | After step 2 the UE shall re-transmit the RRC CONNECTION REQUEST message again in order to continue the RRC connection establishment procedure.
After step 3 the SS shall check IE "UE Specific Behaviour Information 1 idle" isn't included in received RRC CONNECTION REQUEST message.
After step 6 the UE shall establish an ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.2 RRC Connection Establishment: Success after T300 timeout | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.2.1 Definition | 8.1.2.2.2 Conformance requirement
If the UE has not yet received an RRC CONNECTION SETUP message with the value of the IE "Initial UE identity" equal to the value of the variable INITIAL_UE_IDENTITY; and
if expiry of timer T300 occurs:
the UE shall:
1> check the value of V300; and
2> if V300 is equal to or smaller tha... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.2.5 Test requirement | After step 2 the UE shall select either PRACH No.1 or PRACH No.2 and transmit an RRC CONNECTION REQUEST message.
After step 6 the UE shall re-send another RRC CONNECTION REQUEST message.
After step 9 the UE shall transmit an RRC CONNECTION SETUP COMPLETE message and establish an RRC connection on the DCCH logical chann... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.3 RRC Connection Establishment: Failure (V300 is greater than N300) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.3.2 Conformance requirement | The UE shall initiate the procedure when upper layers in the UE requests the establishment of a signalling connection and the UE is in idle mode (no RRC connection exists).
Upon initiation of the procedure, the UE shall:
1> set the IE "Initial UE identity" in the variable INITIAL_UE_IDENTITY according to TS 25.331 subc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.3.5 Test requirement | After step 5, counter K shall be equal to (N300+1) and there shall be no uplink transmission in the monitoring period specified in step 5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.4 RRC Connection Establishment: Reject ("wait time" is not equal to 0) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.4.1 Definition | 8.1.2.4.2 Conformance requirement
When the UE receives an RRC CONNECTION REJECT message on the downlink CCCH, it shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION REJECT message with the value of the variable INITIAL_UE_IDENTITY:
If the values are different, the UE shall ignore the... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.4.5 Test requirement | After step 3 the UE shall have successfully re-selected to cell 4. UE shall trigger the start of RRC connection establishment by transmitting RRC CONNECTION REQUEST. The establishment cause shall be originating call.
After step 5 the UE shall observe the period specified in IE "wait time" of the RRC CONNECTION REJECT m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.5 RRC Connection Establishment: Reject ("wait time" is not equal to 0 and V300 is greater than N300) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.5.2 Conformance requirement | When the UE receives an RRC CONNECTION REJECT message on the downlink CCCH, it shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION REJECT message with the value of the variable INITIAL_UE_IDENTITY:
If the values are different, the UE shall ignore the rest of the message;
If the values... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.5.5 Test requirement | After step 6, counter K shall be equals to (N300+1) and there shall be no uplink transmission in the monitoring period specified in step 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.6 RRC Connection Establishment: Reject ("wait time" is set to 0) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.6.1 Definition | 8.1.2.6.2 Conformance requirement
When the UE receives an RRC CONNECTION REJECT message on the downlink CCCH, it shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION REJECT message with the value of the variable INITIAL_UE_IDENTITY:
If the values are different, the UE shall ignore the... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.6.5 Test requirement | After step 2 the UE shall transmit an RRC CONNECTION REQUEST message on uplink CCCH upon expiry of T300 timer.
After step 4 the UE shall re-transmit an RRC CONNECTION REQUEST message on the uplink CCCH upon expiry of T300 timer.
After step 6 the UE shall stop sending an RRC CONNECTION REQUEST message, go back to idle m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.7 RRC Connection Establishment in CELL_FACH state: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.7.1 Definition | 8.1.2.7.2 Conformance requirement
The UE shall initiate the procedure when upper layers in the UE requests the establishment of a signalling connection and the UE is in idle mode (no RRC connection exists).
Upon initiation of the procedure, the UE shall:
…
1> set the contents of the RRC CONNECTION REQUEST message acco... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.7.3 Test Purpose | 1. To confirm that the UE is able to enter CELL_FACH state and setup signalling radio bearers using common physical channels.
2. To confirm that the UE indicates the requested UE radio access capabilities (used by UTRAN to decide which RAB to establish) and UE system specific capabilities (may be used by UTRAN to confi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.7.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE transmits an RRC CONNECTION REQUEST message to the SS on the uplink CCCH by attempting to make an outgoing call. Af... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.7.5 Test requirements | After step 3 the UE shall establish the RRC connection, and transmit RRC CONNECTION SETUP COMPLETE message on the DCCH using PRACH physical resource specified in system information block messages. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.8 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.9 RRC Connection Establishment: Success after Physical channel failure and Failure after Invalid configuration | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.9.1 Definition | 8.1.2.9.2 Conformance requirement
If the UE failed to establish, per TS 25.331 subclause 8.5.4, the physical channel(s) indicated in the RRC CONNECTION SETUP message.
After having received an RRC CONNECTION SETUP message with the value of the IE "Initial UE identity" equal to the value of the variable INITIAL_UE_IDENT... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.9.5 Test requirement | After step 3a the UE shall not send any further RRC CONNECTION REQUEST message.
After step 8 the UE shall transmit an RRC CONNECTION SETUP COMPLETE message and establish an RRC connection. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10 RRC connection establishment in CELL_DCH on another frequency | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10.2 Conformance requirement | 1. The UE shall, in the transmitted RRC CONNECTION REQUEST message:
1> set the IE "Establishment cause" to the value of the variable ESTABLISHMENT_CAUSE;
1> set the IE "Initial UE identity" to the value of the variable INITIAL_UE_IDENTITY;
1> set the IE "Protocol error indicator" to the value of the variable PROTOCOL_... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10.3 Test Purpose | To confirm that the UE manages to establish an RRC CONNECTION on another frequency when so required by SS in the RRC CONNECTION SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10.4 Method of test | Initial condition
System simulator: 2 cells – Cell 1 on UARFCN 1 and Cell 4 on UARFCN 4.
UE: "Registered idle mode on CS" (state 2) or "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE. If the UE supports both CS and PS domains, the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.10.5 Test requirement | In step 4, the UE shall send the RRC CONNECTION SETUP COMPLETE message on the frequency indicated in the RRC CONNECTION SETUP message.
8.1.2.10a RRC connection establishment in CELL_DCH on another frequency in a different frequency band
8.1.2.10a.1 Definition
This test case is identical to test case 8.1.2.10 except tha... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11 RRC Connection Establishment in FACH state (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11.2 Conformance requirement | The UE shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION SETUP message with the value of the UE storing "Initial UE identity".
If the values are different, the UE shall:
1> ignore the rest of the message.
If the values are identical, the UE shall:
1> act upon all received informatio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11.3 Test purpose | To confirm that the UE enters to CELL_FACH state and correctly establishes signalling radio bearers using common physical channels of a cell within the frequency band specified by SS in RRC CONNECTION SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11.4 Method of test | Initial Condition
System Simulator: 2 cells–Cells 1 is active and cell 6 is inactive.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Specific Message Content
For system information block 3 for Cell 1 (gives IE's which are differ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.11.5 Test requirement | After step 5 the UE shall transmit RRC CONNECTION SETUP COMPLETE message on the uplink DCCH in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12 RRC Connection Establishment: Reject with interRATInfo is set to GSM | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12.2 Conformance requirement | When the UE receives an RRC CONNECTION REJECT message on the downlink CCCH, it shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION REJECT message with the value of the variable INITIAL_UE_IDENTITY:
If the values are different, the UE shall ignore the rest of the message;
If the values... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12.3 Test Purpose | To verify that the UE shall select the GSM cell when RRC Connection Reject with Inter-RAT info set to GSM is received in response to RRC connection request.
Reference
3GPP TS 25.331, section 8.1.3.9 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12.4 Method of test | Initial condition
System Simulator: 2 cells - Cell 1 is UTRAN, Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9. The Inter-RAT Cell Info List of Cell 1 refers to Cell 9. The 3G Neighbour Cell Description List of Cel... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.12.5 Test requirement | 1) At step 5, UE should respond on GSM cell.
2) At step 7, UE should be in CC state U10 in the GSM cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13 RRC Connection Establishment: Reject with InterRATInfo is set to GSM and selection to the designated system fails | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13.2 Conformance requirement | When the UE receives an RRC CONNECTION REJECT message on the downlink CCCH, it shall compare the value of the IE "Initial UE identity" in the received RRC CONNECTION REJECT message with the value of the variable INITIAL_UE_IDENTITY:
If the values are different, the UE shall ignore the rest of the message;
If the values... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13.3 Test Purpose | To verify that the UE upon receiving RRC Connection Reject with Inter-RAT info set to GSM and failing to select the designated GSM system shall reselect UTRAN cell only after the wait time specified in RRC Connection Reject. The UE shall then continue with the RRC CONNECTION establishment procedure.
Reference
3GPP TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13.4 Method of test | Initial conditions
System Simulator: 2 cells - Cell 1 is UTRAN, the value of N300 is set to 1. Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9. The Inter-RAT Cell Info List of Cell 1 refers to Cell 9. The 3G Neighb... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.13.5 Test requirement | 1) At step 5, RRC connection request is received after wait time. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.14 RRC Connection Establishment using the default configuration for 3.4 kbps signalling bearers | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.2.14.1 Definition |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.