hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.9.4 Method of test | Initial Condition
System Simulator: 1 cell.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS transmits a RADIO BEARER RELEASE message to the UE. In this message, SS commands th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.9.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message using the dedicated physical channel allocated. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.10 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11 Radio Bearer Release for transition from CELL_FACH to CELL_DCH: Failure (Physical channel failure and successful reversion to old configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11.3 Test purpose | To confirm that the UE reverts to the old configuration and transmits a RADIO BEARER RELEASE FAILURE message on the DCCH using AM RLC if the UE fails to release the radio bearers in accordance with the specified settings in RADIO BEARER RELEASE message before T312 timer expires. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traffic volume measurement according to this message and then transmit ME... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.11.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on RACH at every 8s interval.
After step 2 the UE shall transmit a RADIO BEARER RELEASE FAILURE message on the DCCH using AM RLC, setting the value "physical channel failure" in IE "... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.12 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.13 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.14 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15 Radio Bearer Release for transition from CELL_FACH to CELL_FACH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RELEASE message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received information elements a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15.3 Test purpose | To confirm that the UE releases the existing the radio bearer(s) according to the RADIO BEARER RELEASE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS transmits a RADIO BEARER RELEASE message to the UE. The UE releases the radio access bearer and transmits a RADIO BEARER RELEASE COMPLETE message on... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.15.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message using AM RLC on the common physical channel.
After step 4, UE shall transmit a RADIO BEARER RECONFIGURATION FAILURE message to verify that the RAB is properly removed. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16 Radio Bearer Release for transition from CELL_DCH to CELL_DCH: Success (Subsequently received) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16.2 Conformance requirement | If the IE "RRC transaction identifier" is included in a received message, the UE shall perform the actions below. The UE shall:
If the received message is any of the messages:
- RADIO BEARER RELEASE; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
2> if the variable CELL_UPDATE_STARTED ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16.3 Test purpose | To confirm that if the UE receives a new RADIO BEARER RELEASE message before the UE releases the radio bearer according to a previous RADIO BEARER RELEASE message it ignore the new RADIO BEARER RELEASE message and configures according to the previous RADIO BEARER RELEASE message received. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. When the SS transmits a RADIO BEARER RELEASE message to the UE before the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.16.5 Test requirement | After step 2 the UE shall transmit an RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17 Radio Bearer Release for transition from CELL_FACH to CELL_DCH: Success (Subsequently received) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17.2 Conformance requirement | If the IE "RRC transaction identifier" is included in a received message, the UE shall perform the actions below. The UE shall:
If the received message is any of the messages:
- RADIO BEARER RELEASE; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
2> if the variable CELL_UPDATE_STARTED ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17.3 Test purpose | To confirm that if the UE receives a new RADIO BEARER RELEASE message before the UE releases the radio bearer according to a previous RADIO BEARER RELEASE message, it ignores the new RADIO BEARER RELEASE message and configures according to the previous RADIO BEARER RELEASE message received. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17.4 Method of test | Initial Condition
System Simulator: 1 cell.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. When the SS transmits a RADIO BEARER RELEASE message to the UE before the UE releases the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.17.5 Test requirement | After step 2 the UE shall transmit an RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18 Radio Bearer Release from CELL_DCH to CELL_PCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RELEASE message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received information elements a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18.3 Test purpose | To confirm that the UE transmits a RADIO BEARER RELEASE COMPLETE before entering CELL_PCH state after it received a RADIO BEARER RELEASE message and released its radio access bearers. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RELEASE message. The UE transmits a RADIO BEARER RELEASE COMPLETE message using AM RLC and enters into CELL_PCH state. SS cal... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.18.5 Test requirement | After step 1 the UE transmits a RADIO BEARER RELEASE COMPLETE message on uplink DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19 Radio Bearer Release from CELL_DCH to URA_PCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RELEASE message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received information elements a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19.3 Test purpose | To confirm that the UE transmits a RADIO BEARER RELEASE COMPLETE before entering URA_PCH state after it received a RADIO BEARER RELEASE message and released its radio bearers. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RELEASE message. The UE transmits a RADIO BEARER RELEASE COMPLETE message using AM RLC and enters into URA_PCH state. SS call... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.19.5 Test requirement | After step 1 the UE transmits a RADIO BEARER RELEASE COMPLETE message to the UE on uplink DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20 Radio Bearer Release for transition from CELL_DCH to CELL_FACH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
If after state transition the UE enters CELL_F... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20.3 Test purpose | 1. To confirm that the UE transits from CELL_DCH to CELL_FACH according to the RADIO BEARER RELEASE message.
2. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC on a common physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
UE: Registered idle mode on CS" (state 2) or "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE If the UE supports both CS and PS domains, the initia... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.20.5 Test requirement | After step 4 the UE shall transmit a CELL UPDATE message on the CCCH in cell 6.
After step 6 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC in cell 6.
After step 7 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 6.
After step 8 ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21 Radio Bearer Release from CELL_DCH to CELL_PCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
…
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recep... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21.3 Test purpose | 1. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_DCH to CELL_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases the radio access bearer and selects a common physical channel in a dif... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21.4 Method of test | Initial Condition
System Simulator: 2 cells–Cells 1 is active and cell 6 is inactive.
UE: "Registered idle mode on CS" (state 2) or "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE If the UE supports both CS and PS domains, the init... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.21.5 Test requirement | After step 4 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message on uplink DCCH using AM RLC in cell 1.
After step 5 the UE shall transmit a CELL UPDATE message on the CCCH with IE "Cell update cause" set to "cell reselection" in cell 6.
After step 8 the UE shall be in CELL_PCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22 Radio Bearer Release for transition from CELL_FACH to CELL_PCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recepti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22.3 Test purpose | 1. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_FACH to CELL_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases the radio access bearer and selects a common physical channel. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22.4 Method of test | Initial Condition
System Simulator: 1 cell– Cell 1 is active.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state of cell 1. The SS transmits a RADIO BEARER RELEASE message. The UE shall release all radio access bearer and enter CELL_PCH state after it... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.22.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message on uplink DCCH using AM RLC.
After step 4 the UE shall be in CELL_PCH state in cell 1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.23 Radio Bearer Release for transition from CELL_FACH to URA_PCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.23.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.23.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recepti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.23.3 Test purpose | 1. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_FACH to URA_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases the radio access bearer and selects a common physical channel. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.23.4 Method of test | Initial Condition
System Simulator: 1 cell– Cell 1 is active.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state of cell 1. The SS transmits a RADIO BEARER RELEASE message. The UE shall release all radio access bearers and enter URA_PCH state after it... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24 Radio Bearer Release for transition from CELL_DCH to CELL_DCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received information elements as specified in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24.3 Test purpose | 1. To confirm that the UE transits from CELL_DCH to CELL_DCH according to the RADIO BEARER RELEASE message.
2. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC on a dedicated physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
CS-DCCH_DTCH_DCH (state 6-9) or PS_DCCH_DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
Table 8.2.3.24
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA RF Ch... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.24.5 Test requirement | After step 4 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 6.
After step 5 the UE shall be in CELL_DCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25 Radio Bearer Release for transition from CELL_DCH to URA_PCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recepti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25.3 Test purpose | 1. To confirm that the UE transmits a RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_DCH to URA_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases radio access bearer, dedicated physical channel and selects a common ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive
UE: "Registered idle mode on CS" (state 2) or "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE If the UE supports both CS and PS domains, the init... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.25.5 Test requirement | After step 6 the UE shall transmits a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 1.
After step 8 the UE shall be in URA_PCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26 Radio Bearer Release for transition from CELL_FACH to CELL_PCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recepti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26.3 Test purpose | 1. To confirm that the UE transmits a RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_FACH to CELL_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases radio access bearer and selects a common physical channel in a diff... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.2.3.26
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
High Range Test Frequency
CPICH Ec
dB... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.26.5 Test requirement | After step 6 the UE shall transmits a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 1.
After step 8 the UE shall be in CELL_PCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27 Radio Bearer Release for transition from CELL_FACH to URA_PCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
In case the procedure was triggered by recepti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27.3 Test purpose | 1. To confirm that the UE transmits a RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC.
2. To confirm that the UE transits from CELL_FACH to URA_PCH according to the RADIO BEARER RELEASE message.
3. To confirm that the UE releases radio access bearer and selects a common physical channel in a diffe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.2.3.27
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
High Range Test Frequency
CPICH Ec
dBm/... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.27.5 Test requirement | After step 6 the UE shall transmits a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 1.
After step 7 the UE shall be in URA_PCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28 Radio Bearer Release for transition from CELL_FACH to CELL_FACH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28.2 Conformance requirement | If the UE receives:
-a RADIO BEARER RELEASE message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
If the UE was in CELL_FACH state upon receptio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28.3 Test purpose | 1. To confirm that the UE transits from CELL_FACH to CELL_FACH according to the RADIO BEARER RELEASE message.
2. To confirm that the UE transmits RADIO BEARER RELEASE COMPLETE message on the uplink DCCH using AM RLC on a common physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive.
UE: "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE. If the UE supports both CS and PS domains, the initial UE state shall be "Registered idle m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.28.5 Test requirement | After step 6 the UE shall transmit a CELL UPDATE message on the CCCH in cell 6.
After step 8 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC in cell 6.
After step 9 the UE shall transmit a RADIO BEARER RELEASE COMPLETE message on the DCCH using AM RLC in cell 6.
After step 10... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.29 Radio Bearer Release for transition from CELL_DCH to CELL_DCH: Associated with signalling connection release during simultaneous PS and CS call | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.29.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.29.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RELEASE message:
it shall:
1> set the variable ORDERED_RECONFIGURATION to TRUE;
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.21... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.29.3 Test purpose | To confirm that the UE releases the existing radio access bearer and signalling connection according to a RADIO BEARER RELEASE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.3.29.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) as specified in clause 7.4 of TS 34.108
Test Procedure
The UE is in CELL_DCH state of cell 1. The UE initiates a session setup to establish a PS signalling connection. Then UE and SS establish a PS session while the CS call is still active. Th... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.