hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.22 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.23 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24 Transport channel reconfiguration from CELL_DCH to CELL_DCH: Success with uplink transmission rate modification | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24.2 Conformance requirement | If the UE receives:
- a TRANSPORT CHANNEL RECONFIGURATION message:
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS25.214;
1> act upon all received information e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24.3 Test purpose | To confirm that the UE transmits TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC after reconfigure its available uplink TFC according to a TRANSPORT CHANNEL RECONFIGURATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state of cell 1. The SS transmits a TRANSPORT CHANNEL RECONFIGURATION message to the UE to modify the transmission rate. This message includes a new uplink transport... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.24.5 Test requirement | After step 2 the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC.
After step 4 the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25 Transport channel reconfiguration from CELL_FACH to CELL_DCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25.2 Conformance requirement | If the UE receives:
-a TRANSPORT CHANNEL RECONFIGURATION message;
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS25.214;
1> act upon all received information el... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25.3 Test purpose | 1. To confirm that the UE transits from CELL_FACH to CELL_DCH according to TRANSPORT CHANNEL RECONFIGURATION message.
2. To confirm that the UE transmits TRANSPORT CHANNEL RECONFIGURATION message on the uplink DCCH using AM RLC on dedicated physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.2.4.25
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA RF Channel Number
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.25.5 Test requirement | After step 4 the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC in cell 6.
After step 5 the UE shall be in CELL_DCH state of cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.26 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.27 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.28 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29 Transport Channel Reconfiguration for transition from CELL_DCH to CELL_DCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29.2 Conformance requirement | If the UE receives:
-a TRANSPORT CHANNEL RECONFIGURATION message;
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS25.214;
1> act upon all received information el... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29.3 Test purpose | 1. To confirm that the UE transits from CELL_DCH to CELL_DCH according to the TRANSPORT CHANNEL RECONFIGURATION message.
2. To confirm that the UE transmits the TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC on a dedicated physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
UE: CS-DCCH_DTCH_DCH (state 6-9) or PS_DCCH_DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
Table 8.2.4.29
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.29.5 Test requirement | After step 4 the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC in cell 6.
After step 5 the UE shall be in CELL_DCH state in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.30 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.31 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.32 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.33 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.34 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.35 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36 Transport Channel Reconfiguration from CELL_DCH to CELL_DCH: Success (with active HS-DSCH reception, not changing the value of TTI during UL rate modification) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36.1 Definition and applicability | All UEs which support FDD or TDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36.2 Conformance requirement | In case the procedure was triggered by reception of a TRANSPORT CHANNEL RECONFIGURATION message, the UE shall:
1> transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE as response message on the uplink DCCH using AM RLC.
…
If the UE receives a message in which presence is needed for the IE "Activation time", and the va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36.3 Test purpose | To confirm that the UE reconfigures the transport and physical channel while being mapped to HS-DSCH according to the received TRANSPORT CHANNEL RECONFIGURATION message.
To confirm that the UE keeps the same value of TTI (transmission time interval) during the procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD or TDD
- UE supports HS-PDSCH
Test Procedure
The UE is in CELL_DCH state and only signalling radio bearers have been established. SS initiates P25 to make the U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.4.36.5 Test requirements | After step 1, the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC.
After step 3, the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message on the DCCH using AM RLC.
After step 5, the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message o... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5 Transport format combination control | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.1 Void | NOTE: Test case “Transport format combination control in CELL_DCH: restriction” have been removed as being implicitely tested by radio bearer test cases in clause 14. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.2 Void | NOTE Test case “Transport format combination control in CELL_DCH: release a restriction” have been removed as being implicitely tested by radio bearer test cases in clause 14. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.3 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4 Transport format combination control in CELL_DCH: Failure (Invalid configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4.2 Conformance requirement | If the variable INVALID_CONFIGURATION is set to TRUE due to the received TRANSPORT FORMAT COMBINATION CONTROL message the UE shall:
1> if the TRANSPORT FORMAT COMBINATION CONTROL message was received on AM RLC:
2> keep the TFC subset existing before the TRANSPORT FORMAT COMBINATION CONTROL message was received;
2> tran... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4.3 Test purpose | To confirm that the UE transmits a TRANSPORT FORMAT COMBINATION CONTROL FAILURE message on the DCCH using AM RLC if it receives a TRANSPORT FORMAT COMBINATION CONTROL message including an invalid configuration. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: DCCH+DTCH_DCH (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traffic volume... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.5.4.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 4 the UE shall transmit a TRANSPORT FORMAT COMBINATION CONTROL FAILURE message on the DCCH using AM RLC, setting IE "failure cause" to "invali... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6 Physical channel reconfiguration | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH (code modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1.2 Conformance requirement | If the UE receives:
- a PHYSICAL CHANNEL RECONFIGURATIONmessage; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received information... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1.3 Test purpose | To confirm that the UE reconfigures the physical channel parameters according to a PHYSICAL CHANNEL RECONFIGURATION message received from the SS. After the reconfiguration, the UE shall be able to communicate with the SS on the new physical channel. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending to the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message to the UE, whi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.1.5 Test requirement | After step 1 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
8.2.6.1a Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH (code modification): Success (1.28 Mcps TDD Only)
8.2.6.1a.1 Definition
8.2.6.1a.2 Conformance requirement
If the UE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH (code modification): Failure (Unsupported configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2.2 Conformance requirement | If the UTRAN instructs the UE to use a configuration, which it does not support and/or if the received message causes the variable UNSUPPORTED_CONFIGURATION to be set to TRUE, the UE shall:
1> transmit a failure response as specified in TS 25.331 subclause 8.2.2.9, setting the information elements as specified below:
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2.3 Test purpose | To confirm that the UE keeps its configuration and transmits a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC if the received PHYSICAL CHANNEL RECONFIGURATION message includes unsupported configuration parameters for the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform per... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.2.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 1 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC.
After step 2, the UE shall transmit a MEA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.3 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.4 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH (code modification): Failure (Incompatible simultaneous reconfiguration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5.2 Conformance requirement | If the received message is any of the messages:
- PHYSICAL CHANNEL RECONFIGURATION; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
…
3> if the IE "RRC transaction identifier" of the received message is identical to the "RRC transaction identifier" stored for the same "Message Type" as ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5.3 Test purpose | To confirm that if the UE receives a PHYSICAL CHANNEL RECONFIGURATION message during a reconfiguring procedure due to a radio bearer message other than PHYSICAL CHANNEL RECONFIGURATION, it shall keep its configuration as if the PHYSICAL CHANNEL RECONFIGURATION message had not been received and complete the reconfigurat... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RECONFIGURATION message to the UE. The SS t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.5.5 Test requirement | After step 2 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC with IE "failure cause" set to "Incompatible simultaneous reconfiguration".
After step 3 the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message using AM RLC on the DCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH (code modification): Failure (Invalid message reception and Invalid configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6.2 Conformance requirement | If the received reconfiguration message contains a protocol error causing the variable PROTOCOL_ERROR_REJECT to be set to TRUE according to TS 25.331 clause 9, the UE shall perform procedure specific error handling as follows. The UE shall:
1> transmit a failure response message as specified in TS 25.331 subclause 8.2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6.3 Test purpose | To confirm that the UE transmits a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC if it receives an invalid PHYSICAL CHANNEL RECONFIGURATION message which does not include any IEs except IE "Message Type".
To confirm that the UE transmits a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform per... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.6.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 1 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC, setting value "protocol error" in IE "fai... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7 Physical channel reconfiguration for transition from CELL_DCH to CELL_FACH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7.2 Conformance requirement | If the UE receives:
- a PHYSICAL CHANNEL RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received informatio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7.3 Test purpose | To confirm that the UE reconfigures a common physical channel according to the PHYSICAL CHANNEL RECONFIGURATION message, which invoke the UE to transit from CELL_DCH to CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108
Test Procedure
The UE is in CELL_DCH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message to the UE. The UE shall then reconfigure the specified common physical channel according to this me... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.7.5 Test requirement | After step 2 the UE shall transit from CELL_DCH to CELL_FACH and transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE messageon the common physical channel. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8 Physical channel reconfiguration for transition from CELL_DCH to CELL_FACH: Success (Cell re-selection) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8.2 Conformance requirement | If the UE receives:
- a PHYSICAL CHANNEL RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received informatio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8.3 Test purpose | To confirm that the UE transmits a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message after the UE completes a cell update procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108
Test Procedure
The UE is in CELL_DCH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message, which includes IE "Primary CPICH info"" (for FDD) or "Primary CCPCH info" (for TDD) and no dedica... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.8.5 Test requirement | After step 3 the UE shall transmit a CELL UPDATE message on the CCCH with IE "Cell update cause" set to "cell reselection".
After step 5 UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC.
After step 6 UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the DCCH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9 Physical channel reconfiguration for transition from CELL_FACH to CELL_DCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9.2 Conformance requirement | If the UE receives:
- a PHYSICAL CHANNEL RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214;
1> act upon all received informatio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9.3 Test purpose | To confirm that the UE reconfigures a new physical channel according to a PHYSICAL CHANNEL RECONFIGURATION message, which invoke UE to transit from CELL_FACH to CELL_DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108
Test Procedure
The UE is in CELL_DCH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message to the UE to transit from CELL_DCH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.9.5 Test requirement | After step 2 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION message on the common physical channel.
After step 5 the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION message on the new dedicated physical channel.
8.2.6.9a Physical channel reconfiguration for transition from CELL_FACH to CELL_DCH: Success(... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.10 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11 Physical channel reconfiguration for transition from CELL_FACH to CELL_DCH: Failure (Physical channel failure and successful reversion to old configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11.3 Test purpose | To confirm that the UE reverts to the old configuration and transmits a PHYSICAL CHANNEL RECONFIGURATION FAILURE message on the DCCH using AM RLC if the UE fails to reconfigure the new physical channel according to a PHYSICAL CHANNEL RECONFIGURATION message before the T312 expiry. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108
Test Procedure
The UE is in CELL_DCH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message to the UE to invoke the UE to transit from CELL_DCH to CELL_FACH. The UE shall reconfigure the comm... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.11.5 Test requirement | After step 2 the UE shall transit from CELL_DCH to CELL_FACH and transmit a PHYSICAL CHANNEL RECONFIGURATION message on the common physical channel.
After step 3a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on RACH at every 8s interval.
Aft... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.12 Physical channel reconfiguration for transition from CELL_FACH to CELL_DCH: Failure (Physical channel failure and cell update ) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.12.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.