hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.1.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.2 mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.1.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/AFS in kbit/s
CODEC_MODE_4
10,2
CODEC_MODE_3
7.4
CODEC_MODE_2
6,7
CODEC_MODE_1
5,15
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.1.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2 Performance of the Codec Mode Request Generation – TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.2 Conformance Requirement | For TULow channel conditions with ideal frequency hopping without DTX activated, the MS shall produce Codec Mode Requests with the following accuracy:
Requirement 1: When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mode with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUHigh and frequency hopping propagation condi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 7.95 mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/AHS in kbit/s
CODEC_MODE_4
7.4
CODEC_MODE_3
6.7
CODEC_MODE_2
5.15
CODEC_MODE_1
4.75
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.2.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3 Performance of the Codec Mode Request Generation – TCH/AFS - improved RX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.2 Conformance Requirement | For TULow channel conditions with ideal frequency hopping without DTX activated, the MS shall produce Codec Mode Requests with the following accuracy:
Requirement 1: When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mode with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUHigh and frequency hopping propagation condi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.2 mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/AFS in kbit/s
CODEC_MODE_4
10,2
CODEC_MODE_3
7.4
CODEC_MODE_2
6,7
CODEC_MODE_1
5,15
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.3.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4 Performance of the Codec Mode Request Generation – TCH/AHS – improved RX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.2 Conformance Requirement | For TULow channel conditions with ideal frequency hopping without DTX activated, the MS shall produce Codec Mode Requests with the following accuracy:
Requirement 1: When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mode with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUHigh and frequency hopping propagation condi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 7.95 mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/AHS in kbit/s
CODEC_MODE_4
7.4
CODEC_MODE_3
6.7
CODEC_MODE_2
5.15
CODEC_MODE_1
4.75
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.4.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5 Performance of the Codec Mode Request Generation – O-TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.2 Conformance Requirement | For TULow channel conditions with ideal frequency hopping without DTX activated, the MS shall produce Codec Mode Requests with the following accuracy:
Requirement 1: When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mode with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUHigh and frequency hopping propagation condi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/AHS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.2 mo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
O-TCH/AHS in kbit/s
CODEC_MODE_4
10,2
CODEC_MODE_3
7.4
CODEC_MODE_2
6,7
CODEC_MODE_1
5,15
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.5.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6 Performance of the Codec Mode Request Generation – O-TCH/WFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.2 Conformance Requirement | For TU3 channel conditions with ideal frequency hopping without DTX activated in GSM900 and GSM850, the MS shall produce Codec Mode Requests with the following accuracy:
- When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.3 Test Purpose | 1. To verify that the MS does not exceed the conformance requirements (for producing codec request) under TU High and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To implicitly verify the correct implementation of the AMR Thresholds and Hysteres... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/WFS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.65 m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
O-TCH/WFS in kbit/s
CODEC_MODE_4
23,85
CODEC_MODE_3
12,65
CODEC_MODE_2
8,85
CODEC_MODE_1
6,6
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decisio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.6.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7 Performance of the Codec Mode Request Generation – O-TCH/WHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.2 Conformance Requirement | For TULow channel conditions with ideal frequency hopping without DTX activated, the MS shall produce Codec Mode Requests with the following accuracy:
Requirement 1: When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mode with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement 1 under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under TUHigh and frequency hopping propagation condi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/WHS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.65 m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.4.2 Procedure | INITIAL CONFIG:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
O-TCH/WHS in kbit/s
CODEC_MODE_2
8,85
CODEC_MODE_1
6,6
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thresholds and hysteresis values:
MC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.7.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8 Performance of the Codec Mode Request Generation – TCH/WFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.1 Definition | When a traffic channel supporting a WB-AMR speech codec is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.2 Conformance Requirement | For TU3 channel conditions with ideal frequency hopping without DTX activated in GSM900 and GSM850, the MS shall produce Codec Mode Requests with the following accuracy:
- When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector, the MS shall request a higher mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirement (for producing codec request) under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To implicitly verify the correct implementation of the WB-AMR Thresholds and Hysteresis ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/WFS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.65 mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.4.2 Procedure | STEP 1
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/WFS in kbit/s
CODEC_MODE_3
12,65
CODEC_MODE_2
8,85
CODEC_MODE_1
6,6
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thresholds and hysteresis va... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.8.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9 Performance of the Codec Mode Request Generation – TCH/WFS - improved RX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.1 Definition | When a traffic channel supporting an Adaptive Multi-Rate speech codec version 5 is activated, the Codec Mode Request is sent by MS in band every other speech frame to indicate to the Network the recommended codec mode of the ACS to use on the downlink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.2 Conformance Requirement | 3GPP TS 45.009 subclause 3.3.3.3:
For TU3 channel conditions with ideal frequency hopping without DTX activated in GSM900 and GSM850, the MS shall produce Codec Mode Requests with the following accuracy:
- When a carrier to interferer ratio 4 dB higher than a defined upper threshold is applied to the antenna connector,... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.3 Test Purpose | 1. To verify that the MS does not exceed conformance requirements for producing codec mode request under TUHigh and frequency hopping propagation conditions without DTX with an allowance for the statistical significance of the test.
2. To implicitly verify the correct implementation of the AMR Thresholds and Hysteresis... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/WFS with a hopping pattern in the Mid ARFCN range and covering at least 10 frequencies not exceeding 5 MHz. DTX shall not be activated. Power control level shall be set to maximum power.
The initial configuration indicates the use of the 12.65 mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.4.2 Procedure | STEP 1:
1a) The SS uses a Channel Mode Modify procedure to change the active codec set to the following set:
Codec Mode
TCH/WFS in kbit/s
CODEC_MODE_3
12,65
CODEC_MODE_2
8,85
CODEC_MODE_1
6,6
With Initial Codec Mode unspecified, thus the default ICM rule being used and the following decision thresholds and hysteresis v... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.10.9.5 Test requirements | The requirement and minimum set of samples shall not exceed the values given in the following table for each set of thresholds.
Event
Maximum allowed error rate
Minimum No. of samples
C/I increases over Thresholds
11%
2000
C/I decreases below Thresholds
11%
2000
NOTE: The maximum allowed error rates for the C/I thresho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11 DARP Phase 1 Speech bearer tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1 TCH/FS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/FS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/FS under propagation condition TUhigh with an allowance f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/FS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal).
The SS commands the MS to create the traffic... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. The interfering signal level is set to -80 dBm.
The fading c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.1.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Wrong decisi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2 TCH/AFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12,2 kbit/s.
The SS transmits Standard Test Signal C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. The interfering signal level is set to -80 dBm.
The fading c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2 DTS-4 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 12,2 kbit/s.
The SS transmits Standard Test Signal C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.4.2 Procedure | a) In addition to the wanted signal, the SS produces one further interfering signal to produce scenario DTS-4.
A signal of type I5 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -77 dBm.
b) The SS sets the level of the wanted signal to that indicated by Clev in table 14.11.2.2-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.2.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3 DTS-2/3/5 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AFS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.4 Method of test |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.