hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.4.1 Initial condition | The SS is configured for a single input and dual output configuration (SIDO) as defined in annex N.2 2 picture N.2.2 of 3GPP 45.005
The diversity parameter for the antenna correlation is set to 0 and the antenna gain imbalance (AGI) is set to 0 dB
A call is set up according to the generic call set up procedure for pack... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.4.2 Test Procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.4.2.1 DTS-2 Procedure | a) The DTS-2 co-channel interferer signal ICoCh1 is configured according to the DTS-2 configuration.
b) The co-channel interferer signal ICoCh1 set to -70 dBm.
c) The power levels of the interferers ICoCh2, IAdjCh1, and IAWGN are set according to table 14.16.5.2.21. The power levels are defined relative to ICoCh1.
d) T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.5 Test requirement | The block error ratio calculated by the SS for different channels and under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2q, shall be set according to the table below.
Table 14.16.5.2.5-1
GSM 900 and... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18 EGPRS receiver tests | Statistical testing of receiver BLER performance
Error Definition
Block Error Ratio (BLER):
The Block Error Ratio is the ratio of blocks received in error to the total number of received blocks, where a block is defined as received in error if the error detection functions in the receiver, operating in accordance with ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1 Minimum Input level for Reference Performance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1.1 Definition | The minimum input level is the signal level at the MS receiver input at which a certain BLER is met. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1.2 Conformance requirement | 1. The block error rate (BLER) performance for PDTCH/MCS1 to 4 shall not exceed 10 % at input levels according to the table 14.18-3a; and for PDTCH/MCS5 to 9 shall not exceed 10 % or 30 % depending on Coding Schemes at input levels according to the table 14.18-3b.
Table 14.18-3a: PDTCH Sensitivity Input Level for GMSK ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1.3 Test purpose | 1. To verify that the MS sends a Packet Not Acknowledge in the Packet Downlink Ack/Nack in case of the Block Check Sequence indicating a Block Error.
2. To verify that the MS does not exceed conformance requirement 1 for PDTCH with different coding schemes and under different propagation conditions with an allowance fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1.4 Method of test | Initial conditions
NOTE 1: The BA list sent on the BCCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ). Surrounding cell signal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.1.5 Test requirements | In step a) the Packet Downlink Ack/Nack as sent by the MS shall indicate every block transmitted by the SS with incorrect BCS as not acknowledged.
The block error ratio, as calculated by the SS for different channels and under the different propagation conditions, under any combination of normal and extreme test voltag... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2 Co-channel rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2.1 Definition | The co-channel rejection is a measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted modulated signal, both signals being at the nominal frequency of the receiver. "Wanted signal" in this test is the signal generated by the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2.2 Conformance requirement | 1. The block error rate (BLER) performance for PDTCH/MCS1 to 4 shall not exceed 10 % at co-channel interference ratios (C/Ic) exceeding those according to the table 14.18-5a; and for PDTCH/MCS5 to 9 shall not exceed 10 % or 30 % depending on Coding Schemes at co-channel interference ratios (C/Ic) exceeding those accord... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 for different coding schemes and under different propagation conditions with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under propagation condition TUhigh/noFH, with an ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2.4 Method of test | Initial conditions
For both GMSK and 8-PSK modulations, a downlink TBF is set up according to the generic procedure specified in clause 40 for packet switched with an ARFCN in the mid ARFCN range, power control level set to maximum power. The power control parameter ALPHA (α) is set to 0.
The SS transmits EGPRS RLC dat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.2.5 Test requirements | The block error ratio, as calculated by the SS for different channels and under the different propagation conditions, shall not exceed the conformance requirement.
14.18.2a Co-channel rejection in EGPRS2A
14.18.2a.1 Definition
The co-channel rejection is a measure of the capability of the receiver to receive a wanted m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3 Adjacent channel rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.1 Definition | The adjacent channel selectivity is a measure of the capability of the receiver to receive wanted data packets without exceeding a given degradation due to the presence of an interfering signal (I1) in the adjacent channel. "Wanted signal" in this test is the signal generated by the transmitted RLC data blocks.
The adj... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.2 Conformance requirement | 1. For GMSK modulation, under adjacent channel interference at 200 kHz above and below the wanted signal frequency and at the adjacent interference ratio (C/Ia1) exceeding C/Ic - 18dB where C/Ic is the co-channel interference ratio specified in table 14.18-5a for PDTCH and table 14.18-6a for USF channels.
1.1 For a TUh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.3 Test purpose | 1 To verify that the conformance requirements 1.1, 1.2, 1.3 and 1.4 are met with an allowance for the statistical significance of the test in the presence of a GMSK modulated adjacent channel interferer under propagation condition TUhigh at 200 kHz above and below the wanted signal frequency.
2 To verify that the confo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.4 Method of test | Initial conditions
For both GMSK and 8-PSK modulations, a downlink TBF is set up according to the generic procedure specified in clause 40 for packet switched with an ARFCN in the mid ARFCN range, power control level set to maximum power. The power control parameter ALPHA (α) is set to 0. The SS transmits EGPRS RLC dat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.5 Test requirements | The block error ratio, as calculated by the SS for different channels with different coding schemes and under TUhigh propagation condition, under any combination of normal and extreme test voltages and ambient temperatures, shall not exceed the conformance requirement.
Testing of the conformance requirement for USF/MCS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.5.1 Fixed limit test with minimum number of samples | The fixed testing of the conformance requirement is done using the minimum number of samples and the limit BLER given in table 14.18‑2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.3.5.2 Statistical test with early pass / fail decision | Specific details on statistical testing of BER/BLER performance are defined in Annex 7.
Minimum test time due to fading conditions has to be considered before checking the conformance limits. The minimum test time for the specific fading condition are specified in the table 14.18.3.5-1.
Table 14.18.3.5-1: Minimum test ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4 Intermodulation rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4.1 Definition | The intermodulation rejection is a measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of two or more unwanted signals with a specific frequency relationship to the wanted signal frequency. "Wanted signal" in this test is the signal ge... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4.2 Conformance requirement | In the presence of two unwanted signals with a specific frequency relationship to the wanted signal frequency in both GMSK and 8-PSK modulations
1. The block error rate (BLER) performance for PDTCH/MCS1 to 4 shall not exceed 10 % and for PDTCH/MCS5 to 9 shall not exceed 10 % or 30 % depending on Coding Schemes; 3GPP TS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4.3 Test purpose | 1. To verify that the MS does not exceed the conformance requirements for different channels and coding schemes under the static condition with an allowance for the statistical significance of the test.
2. To verify that Conformance Requirements are met under extreme conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4.4 Method of test | NOTE: The measurements address the third order intermodulation, which represents the most serious case.
Initial conditions
For both GMSK and 8-PSK modulations, a downlink TBF is set up according to the generic procedure specified in clause 40 for packet switched with an ARFCN in the Mid ARFCN range, power control level... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.4.5 Test requirements | The block error ratio, as calculated by the SS for different channels with different coding schemes and under static condition, under any combination of normal and extreme test voltages and ambient temperatures, shall not exceed the conformance requirement.
14.18.4a Intermodulation rejection in EGPRS2A configuration
14... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5 Blocking and spurious response | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.1 Definition | Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal in the presence of an unwanted input signal, on frequencies other than those of the spurious responses or the adjacent channels, without exceeding a given degradation. "Wanted signal" in this test is the signal generated by ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.2 Conformance requirement | 1. The blocking characteristics of the receiver are specified separately for in-band and out-of-band performance as identified in 3GPP TS 05.05 subclause 5.1.
2. The block error rate (BLER) performance for PDTCH/MCS1 to 4 shall not exceed 10 % and for PDTCH/MCS5 to 9 shall not exceed 10 % or 30 % depending on Coding Sc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.3 Test purpose | 1. To verify that the in band blocking performance is met without exceeding the total number of allowed in band spurious responses. An allowance is made for the statistical significance of the test.
2. To verify that at selected out of band frequencies, the out of band blocking performance is met without exceeding the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.4 Method of test | Initial conditions
A call is set up according to the generic call set up procedure, except the BCCH frequency list shall be empty, on a TCH with an arbitrary ARFCN in the range supported by the MS. The power control level is set to maximum power. The ARFCN of the BCCH shall be the same - or at an offset of +/- 2 channe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.5 Test requirements | The block error ratio as calculated by the SS for different channels and coding schemes shall not exceed the conformance requirement. Testing the conformance requirement can be done either in the classical way with a fixed minimum number of samples (refer to section 14.18.5.5.2) or using statistical methods that lead t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.5.1 Statistical testing of blocking and spurious response performance with early decision | For more information on statistical testing of blocking and spurious response performance, especially the definition of limit lines, refer to Annex 7.
Wrong decision risk F for one single error rate test:
Fpass ≠ Ffail As the blocking test case comprises of many BLER tests the wrong decision risk for a fail decisio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.5.5.2 Fixed testing of blocking and spurious response performance with minimum number of samples | The fixed testing of the conformance requirement is done using the minimum number of samples and the limit BLER given in table 14.18‑2.
14.18.5a Blocking and spurious response in EGPRS2A configuration
14.18.5a.1 Definition
Blocking is a measure of the ability of the receiver to receive a modulated wanted input signal ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6 EGPRS Usable receiver input level range | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6.1 Definition | The usable receiver input level range is the range of the radio frequency input level of a specified modulated signal over which bit error ratio stay between specified limits. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6.2 Conformance requirement | 1. The receiver input level range requirements of 3GPP TS 05.05 subclause 6.1 for raw data bits of GMSK modulation under static and EQ propagation conditions shall be met:
1.1 Under normal conditions.
1.2 Under extreme conditions.
2. The receiver input level range requirements of 3GPP TS 05.05 subclause 6.1 for raw dat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6.3 Test purpose | 1. To verify that the MS does not exceed the conformance requirement with an allowance for the statistical significance of the test.
1.1 Under normal conditions.
1.2 Under extreme conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6.4 Test Method | Initial Conditions
The MS is assumed to be EGPRS attached. The power control parameter ALPHA (α) is set to 0.
The SS establishes a downlink TBF on one timeslot.
The SS commands the MS to request an establishment of the TBF Uplink and to create a channel loop back after demodulation and before decoding. This is achieved... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.6.5 Test Requirements | The error rate measured in this test shall not exceed the test limit error rate values given in table 14.18-10. This shall apply for any combination of normal and extreme test voltages and ambient temperature, for the different propagation conditions and for any level of input signal to the receiver.
Table 14.18-10: Li... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.7 Incremental Redundancy Performance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.7.1 Definition | In Incremental Redundancy RLC mode, soft information from multiple, differently punctured versions of an RLC data block may be used when decoding the RLC data block. This significantly increases the link performance. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.7.2 Conformance requirement | An EGPRS capable MS shall, under the conditions stated in the table below, achieve a long-term throughput of 20 kbps per time slot (see NOTE) measured between LLC and RLC/MAC layer.
Propagation conditions
Static, input level –97.0 dBm
Modulation and Coding Scheme
MCS-9
Acknowledgements polling period
32 RLC data blocks... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.7.3 Test purpose | To verify that the EGPRS MS can operate in Incremental Redundancy RLC mode for a sufficiently long time and that it achieves a long-term throughput of 20 kbps per timeslot, measured between LLC and RLC/MAC layer, under the conditions defined in conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.7.4 Method of test | The SS establishes a downlink TBF in Incremental Redundancy RLC mode, beginning on a Mid ARFCN Range, under the conditions defined in the conformance requirement. The downlink data transfer is preceded with random payload data according to the Incremental Redundancy RLC mode procedures using MCS-9. The throughput betwe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8 DARP Phase 1 EGPRS tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1 Synchronous single co-channel interferer (DTS-1) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.1 Definition | The DARP reference test scenario DTS-1 for a single synchronous co-channel interferer defines an interfering signal and corresponding performance limits. This test is a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of this s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference performa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.3 Test purpose | To verify that the MS does not exceed conformance requirement for different coding schemes and under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.4.1 Initial condition | A downlink TBF is established according to the generic call set up procedure with an ARFCN in the mid ARFCN range, power control level set to maximum power. The power control parameter ALPHA (α) is set to 0.
The SS establish a downlink TBF.
The SS transmits Standard Test Signal C1 with TSC 0.
In addition to this wanted... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.4.2 Procedure | a) The co-channel interferer signal I1 (unwanted signal) is set to -80 dBm.
b) The fading characteristic of the wanted signal C1 and the interferer signal I1 is set to TU High. No FH applies.
c) The SS transmits packets using MCS-1 coding to the MS on all allocated timeslots.
d) The SS sets the level of the wanted sign... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.1.4.3 Test requirement | The block error ratio, as calculated by the SS for different channels under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2ae shall be set according to the table 14.18.8.1.4.3-1 and 14.18.8.1.4.3-2.
T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2 Synchronous single co-channel interferer (DTS-2 / DTS-3) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.1 Definition | The DARP reference test scenarios DTS-2 and DTS-3 for multiple synchronous interferers define a set of interfering signals and the corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the pres... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.2 Conformance requirement | The block error rate (BLER) performance for PDTCH / CS-1 to CS-4 shall not exceed 10 % at the multiple interference ratios (C/Ic) according to table 14.18.8.2.2-1.
Table 14.18.8.2.2-1: Reference Test Scenarios for synchronous multiple interferers
Reference Test Scenario
Interfering Signal
Interferer relative power leve... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.3 Test purpose | To verify that the MS does not exceed the conformance requirement for different PDTCH / MSC 1-4 coding schemes under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4.1 Initial condition | A TBF is established according to the generic call set up procedure for packet switched on an ARFCN in the Mid range, on the maximum number of receive timeslots which the MS is capable to support, The MS is transmitting at maximum power. The power control parameter ALPHA (α) is set to 0.
The SS establish a downlink TB... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4.2 Test procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4.3 DTS-2 procedure | a) The DTS-2 co-channel interferer signal ICoCh1 is configured according to DTS-2 configuration.
b) The co-channel interferer signal ICoCh1 set to -80 dBm.
c) The power levels of the interferers ICoCh2 , IAdjCh1, and IAWGN are set according to table 14.18.8.2.2-1. The power levels are defined relative to ICoCh1.
d) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4.4 Test method | a) The DTS-3 co-channel interferer signal ICoCh1 is configured according to DTS-3 configuration.
b) The SS repeats the steps (b) to (h) identical to the DTS-2 procedure |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.8.2.4.5 Test requirement | The block error ratio, as calculated by the SS for different channels and under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 (table 2o, annex L) , shall be set according to the table below.
Table 14.18.8.2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9 DARP Phase II EGPRS tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1 Synchronous single co-channel interferer (DTS-1) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.1 Definition | The DARP phase II reference test scenario DTS-1 for a single synchronous co-channel interferer defines an interfering signal and corresponding performance limits. This test is a measure of the capability of the DARP phase II receivers to receive a wanted modulated signal without exceeding a given degradation due to the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N
The reference performance shall be:
- For packet switched channels (PDTCH) BLER: 10 %
The values in table 2q are given as the C/I1 ratio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.3 Test purpose | To verify that the MS does not exceed conformance requirement for different coding schemes and under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.4.1 Initial condition | The SS is configured as defined in annex N.2 picture N.2.2 of 3GPP 45.005
The diversity parameter for the antenna correlation is set to 0 and the antenna gain imbalance (AGI) is set to 0 dB
A call is set up according to the generic call set up procedure with an ARFCN in the mid ARFCN range on the maximum number of rece... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.4.2 Procedure | a) The co-channel interferer signal I1 (unwanted signal) is set to -70 dBm.
b) The fading characteristic of the wanted signal C1 and the interferer signal I1 is set to TU High. No FH applies.
c) The SS transmits packets using MCS-1 coding to the MS on all allocated timeslots.
d) The SS sets the level of the wanted sign... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.1.5 Test requirement | The block error ratio, as calculated by the SS for different channels under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2q shall be set according to the table below.
Table 14.18.9.1.5-1
GSM 900 and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2 Synchronous single co-channel interferer (DTS-1b) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.1 Definition | The DARP phase II reference test scenario DTS-1 for a single synchronous co-channel interferer defines an interfering signal and corresponding performance limits. This test is a measure of the capability of the DARP phase II receivers to receive a wanted modulated signal without exceeding a given degradation due to the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N
The reference performance shall be:
- For packet switched channels (PDTCH) BLER: 10 %
The values in table 2q are given as the C/I1 ratio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.3 Test purpose | To verify that the MS does not exceed conformance requirement for different coding schemes and under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.4.1 Initial condition | The SS is configured as defined in annex N.2 picture N.2.2 of 3GPP 45.005.
The diversity parameter for the antenna correlation is set to 0 and the antenna gain imbalance (AGI) is set to 0 dB
A call is set up according to the generic call set up procedure with an ARFCN in the mid ARFCN range on the maximum number of rec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.4.2 Procedure | a) The co-channel interferer signal I1 (unwanted signal) is set to -70 dBm.
b) The fading characteristic of the wanted signal C1 and the interferer signal I1 is set to TU High. No FH applies.
c) The SS transmits packets using MCS-5 coding to the MS on all allocated timeslots.
d) The SS sets the level of the wanted sign... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.2.5 Test requirement | The block error ratio, as calculated by the SS for different channels under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2q shall be set according to the table below.
Table 14.18.9.2.5-1
GSM 900 and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3 Multiple interferers (DTS-2 / DTS-5) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.1 Definition | The DARP phase II reference test scenarios DTS-2 and DTS-5 for multiple interferers define a set of interfering signals and the corresponding performance limits. These tests are a measure of the capability of the DARP phase II receivers to receive a wanted modulated signal without exceeding a given degradation due to t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N
The reference performance shall be:
- For packet switched channels (PDTCH) BLER: 10 %
The values in table 2q are given as the C/I1 ratio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.3 Test purpose | To verify that the MS does not exceed the conformance requirement for different coding schemes under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.4.1 Initial condition | The SS is configured as defined in annex N.2 picture N.2.2 of 3GPP 45.005.
The diversity parameter for the antenna correlation is set to 0 and the antenna gain imbalance (AGI) is set to 0 dB
A call is set up according to the generic call set up procedure for packet switched on an ARFCN in the Mid range, on the maximum ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.4.2 Test Procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.4.2.1 DTS-2 Procedure | a) The DTS-2 co-channel interferer signal ICoCh1 is configured according to the DTS-2 configuration.
b) The co-channel interferer signal ICoCh1 set to -70 dBm.
c) The power levels of the interferers ICoCh2, IAdjCh1, and IAWGN are set according to table 14.18.9.3.21. The power levels are defined relative to ICoCh1.
d) T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.4.2.2 DTS-5 Procedure | a) The DTS-5 co-channel interferer signal ICoCh1 is configured according to DTS-5 configuration.
b) The SS repeats the steps (b) to (i) identical to the DTS-2 procedure |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.9.3.5 Test requirement | The block error ratio calculated by the SS for different channels and under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2q, shall be set according to the table below.
Table 14.18.9.3.5-1
GSM 900 and... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10 Latency Reductions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1 Minimum Input level for Reference Performance for PAN | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.18.10.1.1 Definition | The minimum input level is the signal level at the MS receiver input at which a certain BLER is met. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.