hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 10,2 kbit/s.
The SS transmits Standard Test Signal C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.4.2 Procedure | a) In addition to the wanted signal, the SS produces a further four interfering signals to produce scenario DTS-2.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -80 dBm.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.2.3.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3 TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1 DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7,95 kbit/s.
The SS transmits Standard Test Signal C1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces one further interfering signal to produce scenario DTS-1.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -80 dBm.
b) The SS sets the level of the wanted signal to that indicated by Clev in table 14.11.3.1-2 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.1.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3 DTS-2/3 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.2 Conformance requirement | 3. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for TCH/AHS under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the mid ARFCN range, power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The multirate configuration indicates the use of a codec set limited to 7,4 kbit/s.
The SS transmits Standard Test Signal C1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.4.2 Procedure | a) In addition to the wanted signal, the SS produces a further four interfering signals to produce scenario DTS-2.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -80 dBm.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.11.3.3.5 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7.
Wrong decision risk F ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12 DARP Phase 1 Signalling bearer tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1 FACCH/F | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1 FACCH – DTS-1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for FACCH/F under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for FACCH/F under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.4.2 Procedure | a) In addition to the wanted signal, the SS produces an independent, uncorrelated interfering signal, Standard Test Signal I1 (unwanted signal).
The unwanted signal is continuous and has no fixed relationship with the bit transitions of the wanted signal. The interfering signal level is set to -80 dBm.
The fading c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.1.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 7 (A7.1.3.2)
Wrong decisi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2 FACCH – DTS-2-3 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.1 Definition | The DARP reference test scenarios define a set of interfering signals and corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of these specific unwanted modulated signals. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.2 Conformance requirement | 1. MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference perfo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.3 Test purpose | To verify that the MS does not exceed the first conformance requirement for FACCH/F under propagation condition TUhigh with an allowance for the statistical significance of the test.
To verify that the MS does not exceed the second conformance requirement for FACCH/F under propagation condition TUhigh with an allowance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/F with an ARFCN in the mid ARFCN range. The power control level set to maximum power. RADIO_LINK_TIMEOUT is set to maximum.
The SS transmits Standard Test Signal C1 on the traffic channel (wanted signal). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.4.2 Procedure | a) In addition to the wanted signal, the SS produces a further four interfering signals to produce scenario DTS-2.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, and signal level of -80 dBm.
A signal of type I1 using the same ARFCN as C1, with fading characteristics of TUHigh, ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.12.1.2.4.3 Test requirements | Testing should be performed using statistical methods that lead to an early pass/fail decision with test time significantly reduced for MS with FER/BER not on the limit.
For more information on statistical testing of BER/BLER performance, especially the definition of limit lines refer to Annex 6.2.
Wrong decision risk ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.13 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.14 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.15 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16 GPRS receiver tests | Statistical testing of receiver BLER performance
Error Definition
Block Error Ratio (BLER):
The Block Error Ratio is the ratio of blocks received in error to the total number of received blocks, where a block is defined as received in error if the error detection functions in the receiver, operating in accordance with ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1 Minimum Input level for Reference Performance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.1 Definition | The minimum input level is the signal level at the MS receiver input at which a certain BLER is met. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.2 Conformance requirement | 1. The block error rate (BLER) performance shall not exceed 10 % at input levels according to the table below.
Type of
Propagation conditions
channel
static
TUhigh
(no FH)
TUhigh
(ideal FH)
RA
(no FH)
HT
(no FH)
GSM 400, GSM 700, GSM 850 and GSM 900
PDTCH/CS-1
dBm
-104
-104
-104
-104
-103
PDTCH/CS-2
dBm
-104
-100
-101
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.3 Test purpose | NOTE: This test is performed under STATIC propagation conditions to allow implicit testing of the ability of the MS to hop over the full band. The tests under dynamic propagation conditions are better suited to test the minimum input level for reference BLER performance conformance but cannot test hopping over the full... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.4.1 Initial conditions | NOTE 1: The BA list sent on the BCCH and SACCH will indicate at least six surrounding cells with at least one near to each band edge. It is not necessary to generate any of these BCCHs but, if provided the signal strengths of BCCHs shall be in the range 15 dBVemf( ) to 35 dBVemf( ). Surrounding cell signal levels a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.4.2 Procedure | a) The SS transmits packets under Static propagation conditions, using CS-3 coding at a level of 1 dB above the level given in conformance reference 1. Out of the 400 blocks transmitted by the SS, 20 blocks are sent with incorrect BCS, at (pseudo) random positions. The SS checks, for the blocks it transmitted with inco... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.1.5 Test requirements | In step a) the Packet Downlink Ack/Nack as sent by the MS shall indicate every block transmitted by the SS with incorrect BCS as not acknowledged.
The block error ratio, as calculated by the SS for different channels and under the different propagation conditions, under any combination of normal and extreme test voltag... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2 Co-channel rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1 Co-channel rejection for packet channels | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.1 Definition | The co-channel rejection is a measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted modulated signal, both signals being at the nominal frequency of the receiver. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.2 Conformance requirement | 1. The block error rate (BLER) performance shall not exceed 10 % at co-channel interference ratios (C/Ic) exceeding those according to the table below.
Type of
Propagation conditions
channel
TUlow
(no FH)
TUhigh
(no FH)
TUhigh
(ideal FH)
RA
(no FH)
GSM 400, GSM 700, GSM 850 and GSM 900
PDTCH/CS-1
dB
13
10
9
9
PDTCH/CS-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.3 Test purpose | 1. To verify that the MS does not exceed conformance requirement 1 under propagation condition TUlow/no FH, TUhigh/noFH, TUhigh/FH and RA/no FH with an allowance for the statistical significance of the test.
2. To verify that the MS does not exceed conformance requirement 2 under propagation condition TUhigh/noFH, wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.4.1 Initial conditions | A call is set up according to the generic call set up procedure with an ARFCN in the mid ARFCN range, power control level set to maximum power. The power control parameter ALPHA (α) is set to 0.
The SS transmits Standard Test Signal C1.
In addition to this wanted signal (C), the SS produces an independent, uncorrelated... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.4.2 Procedure | a) The SS transmits packets using CS-1 coding to the MS on all allocated timeslots.
b) The fading characteristic of the wanted and the interfering signal is TUlow, no FH applies.
c) The co-channel interference ratio is set to 1 dB above the ratio given in the table in conformance requirement 1. The interferer shall hav... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.2.1.5 Test requirements | The block error ratio, as calculated by the SS for different channels and under the different propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 subclause 6.3 together with subclause 14.16.2.1.4.2 c) shall be set according ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3 Acknowledged mode / Downlink TBF / I_LEVEL measurement report | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.1 Conformance requirements | The PACKET DOWNLINK ACK/NACK message contains a Channel Quality Report (see 3GPP TS 05.08). The optional I_LEVEL measurement results shall be included in at least every other PACKET DOWNLINK ACK/NACK message.
The accuracy of the received signal level and interference measurements shall be as defined in subclause 8.1.2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.2 References | 3GPP TS 04.60, 3GPP TS 44.060, subclause 8.1.2.2.
3GPP TS 05.08, 3GPP TS 45.008, subclauses 10.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.3 Test purpose | To verify that correct I_LEVEL measurement results are included in at least every other PACKET DOWNLINK ACK/NACK message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.5 Initial Conditions | System Simulator:
1) cell, default setting, PBCCH not present. The power control parameter ALPHA (α) is set to 0.
2) The level of the serving cell BCCH and of the PDTCH is set to 30 dB above the reference sensitivity level which is specified in 3GPP TS 05.05. For instance for class 2 or 3 MS, in GSM 900 MS, the level o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.6 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.3.7 Test Procedure | In addition to the wanted signal on PDTCH, the SS produces an uncorrelated co-channel interfering signal, GMSK modulated: the unwanted signal is sent during idle frames of PDTCH of the wanted signal, and has no fixed relationship with the bit transitions of the wanted signal.
This interfering signal is sent on the same... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4 DARP Phase 1 GPRS tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1 Synchronous single co-channel interferer (DTS-1) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.1 Definition | The DARP reference test scenario DTS-1 for a single synchronous co-channel interferer defines an interfering signal and corresponding performance limits. This test is a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of this s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase I (see 3GPP TS 24.008) shall fulfil the requirements in table 2o for wanted signals on GMSK modulated channels under TU50 no FH propagation conditions and GMSK modulated interferers for the test scenarios defined in annex L. The reference performa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.3 Test purpose | To verify that the MS does not exceed conformance requirement for different coding schemes and under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.4.1 Initial condition | A call is set up according to the generic call set up procedure with an ARFCN in the mid ARFCN range, power control level set to maximum power. The power control parameter ALPHA (α) is set to 0.
The SS establish a downlink TBF.
The SS transmits Standard Test Signal C1 with TSC 0.
In addition to this wanted signal (C1),... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.4.2 Procedure | a) The co-channel interferer signal I1 (unwanted signal) is set to -80 dBm.
b) The fading characteristic of the wanted signal C1 and the interferer signal I1 is set to TU High. No FH applies.
c) The SS transmits packets using CS-1 coding to the MS on all allocated timeslots.
d) The SS sets the level of the wanted signa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.1.5 Test requirement | The block error ratio, as calculated by the SS for different channels under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2o.
Table 14.16.4.1.5-1
GSM 900 and GSM 850
PDTCH CS-1
C/dBm
- 77.0
PDTCH CS-2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2 Synchronous multiple interferers (DTS-2 / DTS-3) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.1 Definition | The DARP reference test scenarios DTS-2 and DTS-3 for multiple synchronous interferers define a set of interfering signals and the corresponding performance limits. These tests are a measure of the capability of the DARP receiver to receive a wanted modulated signal without exceeding a given degradation due to the pres... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.2 Conformance requirement | The block error rate (BLER) performance for PDTCH / CS-1 to CS-4 shall not exceed 10 % at the multiple interference ratios (C/Ic) according to table 14.16.4.2.2-1.
Table 14.16.4.2.2-1: Reference Test Scenarios for synchronous multiple interferers
Reference Test Scenario
Interfering Signal
Interferer relative power leve... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.3 Test purpose | To verify that the MS does not exceed the conformance requirement for different coding schemes under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.4.1 Initial condition | A call is set up according to the generic call set up procedure for packet switched on an ARFCN in the Mid range, on the maximum number of receive timeslots which the MS is capable to support, The MS is transmitting at maximum power. The power control parameter ALPHA (α) is set to 0.
The SS establish a downlink TBF.
T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.4.2 Test Procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.4.3 DTS-2 Procedure | a) The DTS-2 co-channel interferer signal ICoCh1 is configured according to DTS-2 configuration.
b) The co-channel interferer signal ICoCh1 set to -80 dBm.
c) The power levels of the interferers ICoCh2 , IAdjCh1, and IAWGN are set according to table 14.16.4.2.2-1. The power levels are defined relative to ICoCh1.
d) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.4.4 DTS-3 Procedure | a) The DTS-3 co-channel interferer signal ICoCh1 is configured according to DTS-3 configuration.
b) The SS repeats the steps (b) to (i) identical to the DTS-2 procedure |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.4.2.5 Test requirement | The block error ratio, as calculated by the SS for different channels and under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 (table 2o, annex L) , shall be set according to the table below.
Table 14.16.4.2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5 DARP Phase II GPRS tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1 Synchronous single co-channel interferer (DTS-1) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.1 Definition | The DARP phase II reference test scenario DTS-1 for a single synchronous co-channel interferer defines an interfering signal and corresponding performance limits. This test is a measure of the capability of the DARP phase II receivers to receive a wanted modulated signal without exceeding a given degradation due to the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N
The reference performance shall be:
- For packet switched channels (PDTCH) BLER: 10 %
The values in table 2q are given as the C/I1 ratio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.3 Test purpose | To verify that the MS does not exceed conformance requirement for different coding schemes and under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.4 Test method | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.4.1 Initial condition | The SS is configured as defined in annex N.2 picture N.2.2 of 3GPP 45.005
The diversity parameter for the antenna correlation is set to 0 and the antenna gain imbalance (AGI) is set to 0 dB
A call is set up according to the generic call set up procedure with an ARFCN in the mid ARFCN range on the maximum number of rece... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.4.2 Procedure | a) The co-channel interferer signal I1 (unwanted signal) is set to -70 dBm.
b) The fading characteristic of the wanted signal C1 and the interferer signal I1 is set to TU High. No FH applies.
c) The SS transmits packets using CS-1 coding to the MS on all allocated timeslots.
d) The SS sets the level of the wanted signa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.1.5 Test requirement | The block error ratio, as calculated by the SS for different channels under the TU High propagation conditions, shall not exceed the conformance requirement.
NOTE: The wanted signal levels derived from calculations using 3GPP TS 45.005 table 2q shall be set according to the table below.
Table 14.16.5.1.5-1
GSM 900 and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2 Multiple interferers (DTS-2 / DTS-5) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.1 Definition | The DARP phase II reference test scenarios DTS-2 and DTS-5 for multiple interferers define a set of interfering signals and the corresponding performance limits. These tests are a measure of the capability of the DARP phase II receivers to receive a wanted modulated signal without exceeding a given degradation due to ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.2 Conformance requirement | MS indicating support for Downlink Advanced Receiver Performance – phase II (see 3GPP TS 24.008) shall fulfil the requirements in table 2q for the test scenarios defined in annex N
The reference performance shall be:
- For packet switched channels (PDTCH) BLER: 10 %
The values in table 2q are given as the C/I1 ratio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 14.16.5.2.3 Test purpose | To verify that the MS does not exceed the conformance requirement for different coding schemes under the propagation condition TU50/noFH with an allowance for the statistical significance of the test. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.