hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.1.2 References | 3GPP TS 45.008, subclauses 6.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.1.3 Test Purpose | To verify that an EC-GSM-IoT and GPRS capable MS, is able to properly select a suitable cell after boot or waking up from a power saving state, independently of the support of EC capability on the Cell target for selection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.1.4 Method of test | Initial conditions
System simulator:
Parameters changed from the default values in table 20.22.1 and 20.22.2.
Parameters:
3 Cells, Cell 1 with GPRS only, Cell 2 with GPRS and EC-GSM-IoT, Cell 3 with EC-GSM-IoT only.
Parameter
Cell 1
Cell 2
Cell 3
Carrier1
Carrier2
Carrier3
BCCH
BCCH/EC-BCCH
BCCH/EC-BCCH
RF Signal (dBm)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.1.5 Test procedure | a) MS is powered on with all cells activated
b) MS is powered off
c) Carrier 3 is deactivated
d) MS is powered on
20.22.33.1.6 Test Requirements
1) After step a), there should be an EC-RACH access on carrier 3 within 45 sec.
2) After step d) there should be a RACH access or EC-RACH access on Cell 2 within 45 sec. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.1.7 Maximum duration of the test | 3 minutes |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2 EC-GSM-IoT Reduced Monitoring – Reselection based on C1_DELTA and Downlink Signalling Failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.1 Conformance requirement | The MS shall proceed as described in sub-clause 6.6.1a.4 if any of the following criteria are fulfilled:
- Cell selection has been completed and monitoring of non-serving cells for cell reselection has not yet been performed;
- C1 ≤ 0;
- A change in BSIC is detected;
- A downlink signalling failure is declared;
- C1a –... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.2 References | 3GPP TS 45.008, subclauses 6.5 and 6.6.1a.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.3 Test Purpose | To verify that an MS that has enabled EC-GSM-IoT, in packet idle mode, supports a reduced monitoring:
- C1_DELTA could trigger a reselection
- A reselection is done on downlink signalling failure
NOTE: For C1_DELTA fine testing, please refer to 20.22.32.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.4 Method of test | Initial conditions
System simulator:
Parameters changed from the default values in table 20.22.1 and 20.22.2
Parameters:
3 Cells, Cell 1 with GPRS only, Cell 2 with GPRS and EC-GSM-IoT, Cell 3 with EC-GSM-IoT Only.
Parameter
Cell 1
Cell 2
Cell 3
Carrier1
Carrier2
Carrier3
BCCH
BCCH / EC-BCCH
BCCH / EC-BCCH
RF Signal (d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.5 Test procedure | a) MS is paged continuously on Carrier 1 / 2 , EC-SCH of carrier 3 is corrupted by SS for 1 min.
b) After 1 min, the RF level of carrier 1 is increased to -60 dBm, MS is paged continuously on Carrier 1 and 3
c) After 2 min, the RF level of carrier 2 is decreased to -85 dBm. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.6 Test Requirements | 1) After step a), there should be an EC-RACH access on carrier 2 within 45 sec.
2) After step b), there should be no access on any carrier (MS remains camped on Cell2)
2) After step c) there should be an EC-RACH access on carrier 3 within 45 sec.
NOTE: The reselection measurement trigger is based on C1_DELTA as C1 as... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.33.2.7 Maximum duration of the test | 5 minutes |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.23 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24 SoLSA Cell Selection and Reselection | All GSM test cases presented in 3GPP TS 11.10 clause 20 are applicable for SoLSA ME with or without LSA SIM. Nevertheless, if LSA SIM are used, it must be checked that no LSA subscription matches the information broadcast by the cell. Otherwise, test cases dealing with cell reselection would fail.
The cell re-selection... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1 SoLSA Cell Selection suitable cell | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.1 Definition | SoLSA Cell selection is a process in which a SoLSA MS, whenever a new PLMN is selected, attempts to find a "suitable cell" of that PLMN to camp on. Two methods of searching for a "suitable cell" are possible, normal cell selection and stored list cell selection. The process ensures that the SoLSA MS is camped on a cell... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.2 Conformance requirement | 1. The SoLSA MS shall be able to select the strongest "suitable cell" and be able to respond to paging on that cell within 30 s of switch on. This requires a valid normal LSA SIM with PIN disabled and ideal radio conditions; 3GPP TS 05.08, subclause 6.1. And it requires a list of LSAs for the subscriber stored on the S... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.3 Test purpose | The SoLSA MS shall be able to select a "suitable cell" according to the normal cell selection criteria. The identification of the LSA is done by using the LSA ID, the CI, the LAC or the LAC + CI. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4 Method of tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.1 SoLSA Cell Selection suitable cell / LSA identified by LSA ID | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.1.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
13/-100
53/-60
63/-50
CBA
0
0
1
0
RXLEV_ACCESS_MIN (dBm... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.1.2 Test Procedure | a) The SS activates all carriers according to table b) and monitors carriers 1, 2 and 4 for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SoLSA MS is switched off.
d) The SS monitors carrier 3 for RA requests from the SoLSA MS.
e) The SoLSA MS is switched on.
f) The SoLSA MS is switched off.
g) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.1.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on the other monitored carriers.
NOTE 1: 33 s for cell selection, 10 s for communicating the data between SIM and ME, 5 s for search of a matching LSA on SIM: allow 50 s.
2) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.2 SoLSA Cell Selection suitable cell / LSA identified by LAC + CI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.2.1 Initial conditions | a) Identification of the LSA by means of LAC + CI (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
13/-100
53/-60
63/-50
CBA
0
0
1
0
R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.2.2 Test Procedure | a) The SS activates all carriers according to table b) and monitors carriers 1, 2 and 4 for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SoLSA MS is switched off.
d) The SS monitors carrier 3 for RA requests from the SoLSA MS.
e) The SoLSA MS is switched on.
f) The SoLSA MS is switched off.
g) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.2.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on the other monitored carriers.
2) There shall be no response from the SoLSA MS on the monitored carrier after step e) within 60 s.
NOTE: Any potential access is likely to occ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.3 SoLSA Cell Selection suitable cell / LSA identified by CI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.3.1 Initial conditions | a) Identification of the LSA by means of CI (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
13/-100
53/-60
63/-50
CBA
0
0
1
0
RXLEV_A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.3.2 Test Procedure | a) The SS activates all carriers according to table b) and monitors carriers 1, 2 and 4 for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SoLSA MS is switched off.
d) The SS monitors carrier 3 for RA requests from the SoLSA MS.
e) The SoLSA MS is switched on.
f) The SoLSA MS is switched off.
g) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.3.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on the other monitored carriers.
2) There shall be no response from the SoLSA MS on the monitored carrier after step e) within 60 s.
NOTE: Any potential access is likely to occ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.4 SoLSA Cell Selection suitable cell / LSA identified by LAC | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.4.1 Initial conditions | a) Identification of the LSA by means of LAC (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
13/-100
53/-60
63/-50
CBA
0
0
1
0
RXLEV_... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.4.2 Test Procedure | a) The SS activates all carriers according to table b) and monitors carriers 1, 2 and 4 for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SoLSA MS is switched off.
d) The SS monitors carrier 3 for RA requests from the SoLSA MS.
e) The SoLSA MS is switched on.
f) The SoLSA MS is switched off.
g) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.1.4.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on the other monitored carriers.
2) There shall be no response from the SoLSA MS on the monitored carrier after step e) within 60 s.
NOTE: Any potential access is likely to occ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2 SoLSA Cell (Re)Selection Emergency Call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.2 Conformance requirement | 1. The SoLSA MS shall be able to initiate emergency calls when no "suitable cells" of the selected PLMN are available, but at least one acceptable cell is available. The SoLSA MS is in limited service state.
An LSA exclusive access cell is "suitable" only if the LSA of the cell is one of the allowed LSA according to th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.3 Test purpose | 1. To verify that the SoLSA MS shall be able to initiate emergency calls when no "suitable cells" of selected PLMN are available, but at least one acceptable cell is available. The available cells are:
a) LSA exclusive access cells of the selected PLMN with no LSA subscription.
b) Normal LSA cell of forbidden PLMN.
2. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.4.1 Initial conditions | a) Parameters changed from the default values in table 20.24.1; further initial conditions for LSA exclusive access cell.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level (dbV emf() / dBm)
38/ ‑75
23 / ‑90
33 / -80
OFF
RXLEV_ACCESS_MIN (dBm)
‑90
‑80
-90
CBA
1 (barred)
0
0
MCC, MNC
Home PLMN
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.4.2 Test Procedure | a) The SS activates the carriers. The SS monitors carriers 1, 2 and 3 for RA requests for the duration of the test.
b) The SoLSA MS is switched on.
c) 60 s after switch on, an emergency call is initiated on the SoLSA MS.
d) The SS changes the CBA of carrier 1 to 0.
NOTE 1: The MS should reselect carrier 1 because it sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.2.4.4 Test requirements | 1) In step c), the first access of the SoLSA MS shall be on carrier 3.
2) In step e), the first access of the SoLSA MS shall be on carrier 1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3 SoLSA Cell Reselection / idle mode support enabled | General Remark
The identification of the LSA is done by means of the LSA ID, see General Remark 2) in subclause 20.24. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.1 General conformance requirement | 1. There are various requirements that a cell must satisfy before a SoLSA MS can perform normal camping on it:
i) It should be a cell of the selected PLMN.
ii) It should not be "barred".
iii) It should not be in an LA which is in the list of "forbidden LA for roaming".
iv) The radio path loss between SoLSA MS and BTS m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2 SoLSA Cell Reselection / idle mode support enabled / LSA Priority | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.1 Definition | While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss crit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.3 Test purpose | To verify that the SoLSA MS when idle mode support for SoLSA on the SIM card is enabled shall favour camping on those LSA cells with the highest LSA priority the SoLSA MS is subscribed to. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
63/ ‑50
53/ ‑60
33 / -80
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN
(dBm)
-90
-90
-90
LAC
C1
4... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.4.2 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) After approx. 60 s the SS is reconfigured and carrier 3 becomes barred (CBA = 1) in order to give the MS the time to perform cell reselection on carrier 3.
d) The SS is reconfigured ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.2.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 (highest C1) within 50 s (Cell Selection).
NOTE 1: 33 s for the MS to read the BCCH of carrier 3 (30 s + 10 %), 10 s for communicating the data between SIM and ME, 5 s for search of a matching LSA on SIM. Total 48 s, allow 50 s.
2) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / different location area | 20.23.3.3.1 Definition
While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss crit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.3 Test purpose | To verify that the SoLSA MS when idle mode support for SoLSA on the SIM card is enabled shall favour camping on those LSA cells with the highest C2 among those cells with the highest LSA priority the SoLSA MS is subscribed to even if the cell belongs to a different location area. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/ ‑70
33/ ‑80
33 / -80
13 / -100
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
-90
-90
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.4.2 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 3 is increased to 63 dBV emf() / -50 dBm (C2 increases to 40 dB).
d) The SS is reconfigured and the level ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.3.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. (Cell Selection, highest C1). There shall be no response from the SoLSA MS on any other carrier within 35 s after first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c),... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4 SoLSA Cell Reselection / idle mode support enabled / Priority Threshold | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.1 Definition | While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.2 Conformance requirement | The SoLSA MS shall be able to calculate correctly the signal strength threshold criterion parameter C4 which is to determine whether prioritised LSA cell reselection shall apply.
The signal strength threshold criterion parameter C4 is used to determine whether prioritised LSA cell reselection shall apply and is defined... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3 SoLSA Cell Reselection / idle mode support enabled / Priority Threshold any value | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3.1 Test purpose | To verify that the SoLSA MS is able to reselect cells correctly according to parameter PRIO_THR. (parameter C4 criterion). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3.2 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3.2.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2.)
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBµV emf() / dBm)
47 / - 66
55 / ‑58
63 / -50
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
-90
‑90
-90
C1
15... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3.2.2 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) Carrier 3 is barred (CBA = 1).
d) The PRIO_THR value of carrier 2 is set to 0 dB (level 0).
e) The PRIO_THR value of carrier 2 is set to 36 dB (level 6).
20.24.3.4.3.2.3 void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.3.2.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s after switch on.
2) After step c), the SoLSA MS shall respond on carrier 1 within 55 s after barring of carrier 3 (Highest Priority + C4 > 0).
3) After step d), the SoLSA MS shall respond on carrier 2 within 55 s after cha... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.4.1 Test purpose | To verify that the SoLSA MS is able to reselect cells correctly according to parameter C2 among those cell not fulfilling C4 0. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.4.2 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.4.2.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
63 / -50
53 / -60
58 / -55
31 / -82
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
-90
-90
-90... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.4.2.2 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 1 is decreased to 33 dBµV emf() / -80 dBm (C2 of carrier 1 becomes 10).
d) The SS is reconfigured and the l... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.4.4.2.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c), there shall be response f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / LSA_OFFSET | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.1 Definition | While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.2 Conformance requirement | While performing cell reselection, the SoLSA MS shall be able to calculate correctly the signal strength threshold criterion parameter consisting of C2 + LSA_OFFSET to determine which LSA cell shall be selected among those having the same LSA priority; 3GPP TS 05.08, subclause 6.6.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.3 Test Purpose | To verify that the SoLSA MS shall be able to reselect the cell with the highest value of C2 + LSA_OFFSET among those cells that have highest LSA priority and fulfil the criteria C4 0. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBµV emf() / dBm)
63 / ‑50
43 / ‑70
33 / ‑80
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
40
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.4.2 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) Carrier 1 is barred (CBA = 1).
d) Carrier 3 is barred (CBA = 1).
20.24.3.5.4.3 void |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.5.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 after 50 s. (highest value of C1). There shall be no response from the SoLSA MS on other carriers within 35s after the first response sent on carrier 1.
NOTE: Any potential access is likely to occur within 25 s.
2) After step c), the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / cell combinations | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss crit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.3 Test purpose | To verify that the SoLSA MS shall reselect the correct cell when subscription for normal LSA cells and LSA exclusive access cells varies. The setting of LSA only bit on the SIM shall not influence the behaviour of the cell reselection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4 Method of tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.1 Initial conditions | a) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
53/ ‑60
43/ ‑70
63 / ‑50
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
30
20
40
C2
30
20
40
C4
30
20
<0
b) Further parameters changed from the default values in tabl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.2.1 Test Procedure | Using conditions from table a), b) and f).
a) The SS activates the carriers 1, 2, 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and carrier 3 becomes barred (CBA = 1).
d) The SS is reconfigured and carrier 2 becomes barred (CBA = 1) and carrie... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.2.3 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 3.
NOTE 1: Any potential access is likely to occur within 35 s.
2) After step c), there shall be response f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.3.1 Test Procedure | Using conditions from table a), c) and f).
a) The SS activates carrier 1 and monitors that carrier for RA requests from the SoLSA MS.
Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) The SS activates the carriers 2 and 3 (carrier 1 is still switched on) and monitors carriers 1, 2 and 3 for RA reques... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.3.3 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 after 60 s (highest LSA Priority on the SIM (8) with C4 0).
3) After step d), there shall be response from SoLSA MS on carrier 3 within 55 s after... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.4.1 Test Procedure | Using conditions from table a), d) and f).
a) The SS activates the carrier 1 and monitors that carrier for RA requests from the SoLSA MS. Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) The SS activates the carriers 2 and 3 (carrier 1 is still switched on) and monitors carriers 1, 2 and 3 for RA re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.4.3 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 after 60 s after carrier 2 and 3 were switched on (LSA with highest Priority (15)).
3) After step d), there shall be response from SoLSA MS on carri... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.5.1 Test Procedure | Using conditions from table a),e) and f).
a) The SS activates carriers 1 and 3 and monitors these for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SS activates carrier 2 and carrier 3 becomes barred. (CBA = 1).
d) The SS is reconfigured and carrier 2 becomes barred. (CBA = 1).
20.24.3.6.4.5.2 v... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.6.4.5.3 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s (Carrier 1 is an LSA exclusive access cell with no matching subscription).
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 55 s.
3) After step d), there shall be no paging response from SoLS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7 SoLSA Cell Reselection / roaming | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.1 Definition | While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- There is a better cell (in terms of the path loss criterion C2) in the same LA.
- The SoLSA MS will then reselect a n... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.