hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.3.2.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.3.2.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3 Signal quality under static conditions - TCH/AFS – DTX off | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.1 Definition | The MS must be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS has to map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set and sub-set of frames, eight levels of RXQUA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.3 Test purpose | 1. To verify, under static propagation conditions, that the received signal quality is measured and mapped to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The multirate configuration indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.3.3.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.3.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.3.3.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4 Signal quality under static conditions - TCH/AHS - DTX Off | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.1 Definition | The MS shall be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS shall map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set and sub-set of frames, eight levels of RXQUA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.3 Test purpose | 1. To verify, under static propagation conditions, that the received signal quality is measured and mapped to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Half rate
The multirate configuration indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.3.4.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.4.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.3.4.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5 Signal quality under static conditions - TCH/AFS – DTX on | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.1 Definition | The MS must be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS has to map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set and sub-set of frames, eight levels of RXQUA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.3 Test purpose | 1. To verify that, for downlink DTX, the reported parameter RXQUAL_SUB is the received signal quality, averaged over the correct frames (SID_UPDATE and SACCH), mapped by the MS to the eight levels RXQUAL scale in a manner that can be related to an equivalent average BER before channel decoding assessed over the reporti... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The multirate configuration indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.3.5.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.5.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.3.5.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6 Signal quality under static conditions - TCH/AHS – DTX On | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.1 Definition | The MS must be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS has to map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set and sub-set of frames, eight levels of RXQUA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.3 Test purpose | 1. To verify that, for downlink DTX, the reported parameter RXQUAL_SUB is the received signal quality, averaged over the correct frames (SID_UPDATE and SACCH), mapped by the MS to the eight levels RXQUAL scale in a manner that can be related to an equivalent average BER before channel decoding assessed over the reporti... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Half rate
The multirate configuration indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.3.6.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.6.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.3.6.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4 Signal quality under TUhigh propagation conditions | In order to have a testing performance corresponding to that in clause 14 for high error rates, the multiplication factor of the tested error rate with respect to the specified error rate have been increased. The following figures have been used (TUHigh propagation conditions):
Specified error rate
Multiplication facto... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1 Signal quality under TUhigh propagation conditions - TCH/FS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.1 Definition | The MS must be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS has to map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of 1 SACCH multiframe. The assessed equivalent BER before channel decoding shall be mapped to the eight levels of RX... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.3 Test purpose | 1. To verify, under TUhigh conditions, that the received signal quality is measured and reported to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of length one SACCH multiframe fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.4.1 Initial conditions | The SS sets up a call according to the generic call set up procedure on a full rate speech channel in the mid ARFCN range. The RADIO_LINK_TIMEOUT parameter is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The SS commands the MS to establish the TCH burst-by-burst loop (C), see s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BERof the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.4.1.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is corr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.1.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.4.1.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2 Signal quality under TUhigh propagation conditions - TCH/AFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.1 Definition | The MS shall be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS shall map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of 1 SACCH multiframe. The assessed equivalent BER before channel decoding shall be mapped to the eight levels of RX... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.3 Test purpose | 1. To verify, under TUhigh conditions, that the received signal quality is measured and reported to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of length one SACCH multiframe fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The multirate configuration indica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.4.2.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.2.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.4.2.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3 Signal quality under TUhigh propagation conditions - TCH/AHS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.1 Definition | The MS shall be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS shall map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of 1 SACCH multiframe. The assessed equivalent BER before channel decoding shall be mapped to the eight levels of RX... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.3 Test purpose | 1. To verify, under TUhigh conditions, that the received signal quality is measured and reported to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of length one SACCH multiframe fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a TCH/AHS with in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Half rate
The multirate configuration indicates the u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.4.3.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.3.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.4.3.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4 Signal quality under TU High propagation conditions - O-TCH/WFS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.1 Definition | The MS shall be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS shall map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.2 Conformance requirement | 1. The received signal quality shall be measured by the MS and BSS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of 1 SACCH block; 3GPP TS 05.08 subclauses 8.2.2.
When the quality is assessed over the full‑set and sub‑set... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.3 Test purpose | 1. To verify, under TUhigh conditions, that the received signal quality is measured and reported to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of length one SACCH multiframe fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.4.1 Initial conditions | A call is set up according to the generic call set up procedure on a O-TCH/WFS with an ARFCN in the Mid ARFCN range, power control level set to maximum power. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The multirate configuration indi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.4.2 Procedure | a) The SS sets the level of the unwanted signal such that the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4, is covered by one of the cases 1 to 13 of table 21.4.4.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported level is cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.4.4.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail.
Table 21.4.4.5: Test criteria and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8 GMSK_MEAN_BEP Measurement for PDTCH | In order to have a testing performance corresponding to that in clause 14 for high error rates, the multiplication factor of the tested error rate with respect to the specified error rate have been increased. The following figures have been used (static propagation conditions):
Specified error rate
Multiplication facto... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.1 Definition | The MS must be capable of measuring the MEAN_BEP parameters under static channel conditions, which is specified in terms of bit error probability (BEP) before channel decoding averaged over the four bursts in a radio block and then filtered for the measurement report. The MS has to map this filtered BEP into MEAN_BEP v... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.2 Conformance requirement | The mapping of the MEAN_BEP to the equivalent BEP and the accuracies to which an MS shall be capable of estimating the quality parameters under static channel conditions are given for EGPRS GMSK in table 21.8-1. The accuracy requirements below apply for sensitivity limited operation for signal levels above the referenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.3 Test purpose | To verify for EGPRS, under static channel conditions, that the BEP is measured and mapped to the MEAN_BEP values defined in subclause 8.2.5 of 3GPP TS 45.008 by the MS in a manner that can be related to an equivalent average BEP before channel decoding. The probability that the correct MEAN_BEP value is reported shall ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.4 Method of test | The SS compares the long-term BER average calculated by counting bit errors determined in EGPRS loop-back mode to a set of related MEAN_BEP values.
The MEAN_BEP values correspond to the same MS-received bits that are looped-back for calculation of the long-term BER average (one-phase approach). For acquiring these MEAN... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.4.1 Initial conditions | The SS produces a wanted signal and a white noise signal as an interferer (random signal) known as unwanted signal, both with static propagation characteristics. The SS transmits the wanted signal (standard test signal C1) on the PDTCH channel using the MCS-4 at the nominal frequency of the receiver and with a level of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.4.2 Procedure | a) The unwanted signal is switched off and the forgetting factor “e” is set to 0.03. The SS orders the MS into the EGPRS Switched Radio Block Loopback Mode as specified in 3GPP TS 44.014 Section 5.5.1. The SS commands the MS into Radio Block Loopback Sub-mode: OFF.
b) The SS commands the MS into Radio Block Loopback Su... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.5 Test requirements | Testing of the conformance requirement can be done either with fixed minimum number of samples or based on the statistical test method that could lead to an early pass/fail decision with test time significantly reduced for a MS not on the limit. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.5.1 Fixed limit test with minimum number of samples | The fixed testing of the conformance requirement is done using the minimum number of samples and the limit error rate given in table 21.8-3.
The number of error events determined in steps d), g) and j) stored in error counters N_high, N_mid and N_low shall not exceed the error event limit defined in table 21.8-3 for ea... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.8.5.2 Statistical test with early pass / fail decision | Specific details on statistical testing of performance are defined in Annex 7.
The calculation of the error rate for this test shall be done according to the values specified in tables 21.8-4.
Table 21.8-4: Statistical error limits for MEAN_BEP_GMSK
Range
Block
per s
Org. error rate requirement
Derived test limit
Targe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9 8PSK_MEAN_BEP Measurement for PDTCH | In order to have a testing performance corresponding to that in clause 14 for high error rates, the multiplication factor of the tested error rate with respect to the specified error rate have been increased. The following figures have been used (static propagation conditions):
Specified error rate
Multiplication facto... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.1 Definition | The MS must be capable of measuring the MEAN_BEP parameters under static channel conditions, which is specified in terms of bit error probability (BEP) before channel decoding averaged over the four bursts in a radio block and then filtered for the measurement report. The MS has to map this filtered BEP into MEAN_BEP v... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.2 Conformance requirement | The mapping of the MEAN_BEP to the equivalent BEP and the accuracies to which an MS shall be capable of estimating the quality parameters under static channel conditions are given for EGPRS 8PSK in table 21.9-1. The accuracy requirements below apply for sensitivity limited operation for signal levels above the referenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.3 Test purpose | To verify for EGPRS, under static channel conditions, that the BEP is measured and mapped to the MEAN_BEP values defined in subclause 8.2.5 of 3GPP TS 45.008 by the MS in a manner that can be related to an equivalent average BEP before channel decoding. The probability that the correct MEAN_BEP value is reported shall ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.4 Method of test | The SS compares the long-term BER average calculated by counting bit errors determined in EGPRS loop-back mode to a set of related MEAN_BEP values.
The MEAN_BEP values correspond to the same MS-received bits that are looped-back for calculation of the long-term BER average (one-phase approach). For acquiring these MEAN... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.4.1 Initial conditions | The SS produces a wanted signal and a white noise signal as an interferer (random signal) known as unwanted signal, both with static propagation characteristics. The SS transmits the wanted signal (standard test signal C1) on the PDTCH channel using the MCS-9 at the nominal frequency of the receiver and with a level of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.4.2 Procedure | a) The unwanted signal is switched off and the forgetting factor “e” is set to 0.03. The SS orders the MS into the EGPRS Switched Radio Block Loopback Mode as specified in 3GPP TS 44.014 Section 5.5.1. The SS commands the MS into Radio Block Loopback Sub-mode: OFF.
b) The SS commands the MS into Radio Block Loopback Su... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.5 Test requirements | Testing of the conformance requirement can be done either with fixed minimum number of samples or based on the statistical test method that could lead to an early pass/fail decision with test time significantly reduced for a MS not on the limit. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.5.1 Fixed limit test with minimum number of samples | The fixed testing of the conformance requirement is done using the minimum number of samples and the limit error rate given in table 21.9-3.
The number of error events determined in steps d), g) and j) stored in error counters N_high, N_mid and N_low shall not exceed 200 for each of the error counters.
Table 21.9-3: Te... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.9.5.2 Statistical test with early pass / fail decision | Specific details on statistical testing of performance are defined in Annex 7.
The calculation of the error rate for this test shall be done according to the values specified in tables 21.8-4.
Table 21.9-4: Statistical error limits for MEAN_BEP_8PSK
Range
Block
per s
Org. error rate requirement
Derived test limit
Targe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10 Measurement accuracy for inter-RAT system (TDD) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1 1,28Mcps TDD Option | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1 1.28Mcps TDD / P-CCPCH RSCP Measurement absolute accuracy in AWGN propagation condition | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.1 Definition | The P-CCPCH_RSCP measurement absolute accuracy in GSM(GPRS) cell is defined as the P-CCPCH_RSCP measured from UE in GSM(GPRS) cell compared to the actual neighbor TD-SCDMA cell P-CCPCH_RSCP. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.2 Minimum Requirements | The accuracy requirements in Table 21.10.1.1.2-1 are valid under the following conditions:
P-CCPCH RSCP -102 dBm
P-CCPCH Ec/Io > -8 dB
DwPCH_Ec/Io > -5 dB
Table 21.10.1.1.2-1: P-CCPCH_RSCP absolute accuracy
Parameter
Unit
Accuracy [dB]
Conditions
Normal condition
Extreme condition
Io [dBm/ 1.28 MHz]
P-CCPCH_RSCP
dBm
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.3 Test Purpose | The purpose of this test is to verify that the relative P-CCPCH RSCP measurement accuracy is within the specified limits. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.4.1 Initial conditions | Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see TS 34.122 clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see TS 34.122 clause G.2.4.
Cell 1 is a GSM cell and cell 2 is a UTRA TDD cell. In the measurement information message it is indicated to the UE that periodic reporting of the UTRA TDD PCCPC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.4.2 Procedure | 1) Initial cell configured according to table 21.10.1.1.4.1-1 and table 21.10.1.1.4.1-2 a call is set up on cell1.
2) SS shall transmit MEASUREMENT INFORMATION message to indicate cell 2 neighbor cell description information based on table 21.10.1.1.4.1-2.
3) UE shall transmit periodically MEASUREMENT REPORT messages.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.10.1.1.5 Test requirements | The P-CCPCH RSCP measurement accuracy shall meet the minimum requirements in clause 21.10.1.1.2 for at least 900 of the 1000 measurement reports in step 4.
NOTE: If the above Test Requirements differ from the Minimum Requirement, then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this tes... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.13 AQPSK_MEAN_BEP measurement for VAMOS I/II/III | In order to have a testing performance corresponding to that in clause 14 for high error rates, the multiplication factor of the tested error rate with respect to the specified error rate have been increased. The following figures have been used (static propagation conditions):
Specified error rate
Multiplication facto... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.13.1 Definition | The MS must be capable of measuring the MEAN_BEP parameters under static channel conditions, which is specified in terms of bit error probability (BEP) before channel decoding averaged over the four bursts of a Speech frame and then filtered for the measurement report. The MS has to map this filtered BEP into MEAN_BEP ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.13.2 Conformance requirement3GPP TS 45.008 subclause 8.2.5 | The mapping of the MEAN_BEP to the equivalent BEP and the accuracies to which an MS shall be capable of estimating the quality parameters under static channel conditions are given in the following tables for GMSK, 8-PSK and AQPSK respectively. The accuracy requirements below apply for sensitivity limited operation for ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.