hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.3 Test Purpose | To verify that the SoLSA MS when idle mode support for SoLSA on the SIM card is enabled shall favour camping on those LSA cells with the highest LSA priority the SoLSA MS is subscribed to even if subscriber is outside of his HPLMN. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24 General remark 2.).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
63/-50
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
‑90
MCC, MNC
VPLMN
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.4.2 Test Procedure | a) The SS activates carrier 1 and carrier 2, pages the MS on these carriers and monitors these for RA requests from the SoLSA MS. Carriers 3 and 4 are switched off.
b) The SoLSA MS is switched on.
c) After approx. 60 s the SS is reconfigured and level of carrier 2 decreases to 33 dBµV/-80dBm (C2 decreases to 10). The S... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.3.7.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 2 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 1 within 25 s after decreasing the level of carrier 2 (highest C2).
3) After step d), there shall be response from the SoLSA MS on carrier 3 within 55... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4 SoLSA Cell Reselection / idle mode support / any value | General Remark
Definition of "idle mode support" is given in subclause 20.24 General Remark 1.
"Idle mode support" is only controlling if 'favouring' shall be done at cell reselection. It does not disable the LSA subscription. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.1 Definition | While camped on a cell of the selected PLMN a SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.2 Conformance requirement | 1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss crit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.3 Test purpose | To verify that the SoLSA MS shall not favour camping on the LSA for which support in idle mode is disabled. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.5 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
63/ ‑50
53/-60
58/-55
31 / -82
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
-90
-90
-90
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.6 Test Procedure | a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 1 is decreased to 33 dBµV emf() / -80 dBm (C2 of carrier 1 becomes 10).
d) The SS is reconfigured and the l... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.4.8 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c), there shall be response f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5 SoLSA Cell Reselection / LSA indication for idle mode | General Remark
Definition of "LSA indication for idle mode" is given in subclause 20.24 General Remark 1.
"LSA indication for idle mode" is only controlling if indication of the LSA name shall be done. It has no influence on the LSA subscription. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.1 General Definition | The SoLSA MS in idle mode may inform the user whether or not the serving cell belongs to the subscribed LSA.
- The indication is dependent on the setting of the idle mode indication bit on the SIM card for that LSA.
- The indication is independent from the setting of the LSA idle mode support bit on the SIM card for th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.2 General conformance requirement | 1. The service subscriber can define a name (alphanumeric name, icon, etc) for each of her allowed LSAs. The MS will, in idle mode and if required by the user, indicate to the user the current LSA. The indication may be the name of the current LSA, as set by the user. The form of display and indication are left to manu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3 SoLSA Cell Reselection / LSA indication for idle mode / idle mode support enabled | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.1 Definition | See general Definition of this subclause. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.2 Conformance requirement | 1. When both idle mode support and idle mode indication are enabled on the SIM card, the SoLSA MS shall display the name (which was defined by the service subscriber) of the current LSA to the user.
2. When idle mode support is enabled and idle mode indication is disabled on the SIM card, it is expected that the SoLSA ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.3 Test Purpose | 1. To verify that if idle mode indication bit on the SIM card is enabled for the LSA, the SoLSA MS supports the LSA indication. The LSA name (text/icon) shall be displayed on the SoLSA MS.
2. To verify that if idle mode indication bit on the SIM card is disabled for the LSA the SoLSA MS does not support the LSA indicat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
OFF
RXLEV_ACCESS_MIN (d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.4.2 Test Procedure | a) The SS activates carrier 1, pages the MS on this carrier and monitors it for RA requests from the SoLSA MS. Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) Carrier 2 and Carrier 3 are switched on. The SS pages the MS on carriers 1, 2 and 3, and monitors these carriers for RA requests from the So... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.3.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no LSA indication on the SoLSA MS (No LSA).
2) After step c), there shall be response from the SoLSA MS on carrier 3 within 25 s (highest LSA Priority (8) on the SIM card). An LSA indication is expected on ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4 SoLSA Cell Reselection / LSA indication for idle mode / idle mode support disabled | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.1 Definition | See general Definition of this subclause. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.2 Conformance requirement | 1. When idle mode support is disabled and idle mode indication is enabled on the SIM card, it is expected that the SoLSA MS displays the LSA name (which was defined by the service subscriber) of the current LSA to the user.
2. When idle mode support is disabled and idle mode indication is disabled on the SIM card, the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.3 Test Purpose | To verify that when idle mode support is disabled, the SoLSA MS shall display the LSA name in dependence from the idle mode indication bit. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.4.1 Initial conditions | a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
OFF
CBA
0
0
0
RXLEV_ACC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.4.2 Test Procedure | a) The SS activates carrier 1, pages this carrier and monitors it for RA requests from the SoLSA MS. Carriers 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) Carrier 2 and carrier 3 are switched on. The SS pages the MS on carriers 1, 2 and 3, and monitors these carriers for RA requests from the SoLSA MS.
d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.24.5.4.4.4 Test Requirements | 1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no LSA indication on the SoLSA MS.
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 25 s (highest C2). An LSA indication is expected on the SoLSA MS.
3) After step d), there s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25 Intersystem Cell Reselection | The default parameters for the GSM/GPRS cell, the accuracy of the MS signal measurements and tolerance of timers, are given in TS 51.010 section 20.22.
The default parameters and tolerances of the UTRAN cells are specified in TS 34.108. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.1 Definition of system information messages | SYSTEM INFORMATION TYPE 3 REST OCTETS
• SI2q indicated on BCCH Norm
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
< RR management Protocol Discriminator bit (4) >
‘0110'B
< Skip Indicator : bit (4) >
‘0000'B
< Message type : bit (8) >
‘0000 0111’B
< SI2 quarter Rest Octets >
< BA_IND : bit >
0
< 3G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.2 Intersystem Cell Reselection/Idle Mode/FDD_Qmin | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.2.1 Conformance requirement | If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
The MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of RLA_C for ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.2.2 Test purpose | To verify that the MS uses the FDD_Qmin parameter at cell re-selection from GSM to UTRAN while in GSM Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.2.3 Method of test | Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50
Off to -48
Ec/No (dB)
-
-6>dB>-16
NOTE 1: MS is IMSI updated on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, GPRS not present.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, cl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.3 Intersystem Cell Reselection/Idle Mode/FDD_Qoffset | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.3.1 Conformance requirement | If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
The MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of RLA_C for ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.3.2 Test purpose | To verify that the MS uses the FDD_Qoffset parameter at cell re-selection from GSM/GPRS to UTRAN while in Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.3.3 Method of test | Initial conditions
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-75
RXLEV_ACCESS_MIN
dBm
-100
FDD_Qoffset
dB
20
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
CPICH_Ec (FDD)
dBm / 3.84 MHz
OFF to -62 to -48
NOTE 1: MS is IMSI updated on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, GPRS not present.
NO... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.4 Intersystem Cell Reselection/Idle Mode/Qsearch_I | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.4.1 Conformance requirement | If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
For FDD, the MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.4.2 Test purpose | To verify that the MS uses the Qsearch_I parameter at cell re-selection from GSM to UTRAN while in Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.4.3 Method of test | Initial conditions
For MS supporting FDD:
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-60 to -77
RXLEV_ACCESS_MIN
dBm
-100
MP_CHANGE_MARK
0
Qsearch_I
15 to 6
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
CPICH_Ec (FDD)
dBm / 3.84 MHz
OFF to -50
For MS supporting TDD:
Parameter
Unit
Cell 1
(GSM)
Test C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.5 Intersystem Cell Reselection / Idle Mode / High Priority | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.5.1 Conformance requirement | If the 3G Cell Reselection list or the E-UTRAN Neighbour Cell list include frequencies of other radio access technologies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non serving GSM cells.
The MS shall then reselect a suitable (see 3GPP TS 25.304 fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.5.2 Test purpose | To verify that the MS uses the priority information and performs cell re-selection to High priority UTRAN cell while in Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.5.3 Method of test | Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50
Off to -60
Ec/No (dB)
-
-6dB
NOTE 1: MS is GPRS attached on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, NC0.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4, Defau... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.6 Intersystem Cell Reselection / Idle Mode / Low Priority | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.6.1 Conformance requirement | If the 3G Cell Reselection list or the E-UTRAN Neighbour Cell list include frequencies of other radio access technologies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non serving GSM cells.
The MS shall then reselect a suitable (see 3GPP TS 25.304 fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.6.2 Test purpose | To verify that the MS uses the priority information and performs cell re-selection to Low priority UTRAN cell while in Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.6.3 Method of test | Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50 to -90
Off to -60
Ec/No (dB)
-
-6dB
NOTE 1: MS is GPRS attached on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, NC0.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.7 Intersystem Cell Reselection / Idle Mode / H_PRIO | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.7.1 Conformance requirement | If the 3G Cell Reselection list or the E-UTRAN Neighbour Cell list include frequencies of other radio access technologies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non serving GSM cells.
The MS shall then reselect a suitable (see 3GPP TS 25.304 fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.7.2 Test purpose | To verify that the MS uses the priority information and performs cell re-selection from GSM to UTRAN, according to hysteresis criteria while in Idle Mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.25.7.3 Method of test | Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50 to -90
Off to -75
Ec/No (dB)
-
-6dB
NOTE 1: MS is GPRS attached on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, NC0.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26 Decoding of BCCH including information for UTRAN TDD cells | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.1 Conformance requirement | When a message is coded using CSN.1 notation, the definition of the CSN.1 syntax in CSN.1 Specification, Version 2.0, shall be used.
Where the description of information elements in this Technical Specification contains bits defined to be "spare bits", these bits shall set to the indicated value (0 or 1) by the sending... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.2 Test purpose | To verify that the MS performs correctly when BCCH of suitable cell includes information for UTRAN-TDD cells. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.3 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.3.1 Initial conditions | Parameters changed from the default values in table 20.1.
Parameter
Carrier 1
Carrier 2
RF Signal Level
(dBV emf() / dBm)
48 / -65
38 / -75
CBA
0
0
RXLEV_ACCESS_MIN
(dBm)
-90
-67
MNC
MCC
C1
25
-8
C2
25
-8
ATT bit
1
1
MSCR
1
1
For an E-GSM MS carrier 2 is chosen in the E-GSM band, carrier 1 ARFCN in the P-GSM band.
Spe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.3.2 Procedure | a) The SS activates the carriers with specific system information settings
b) The MS is switched on.
c) The MS is paged on carrier 1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.4 Test requirements | 1) After step b), the MS shall perform location update procedure on carrier 1 within 60 seconds..
2) After step c), MS shall respond to paging. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.26.5 Specific Message Contents | SYSTEM INFORMATION TYPE 3 REST OCTETS
• SI2q indicated on BCCH Norm
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
< RR management Protocol Discriminator bit (4) >
‘0110'B
< Skip Indicator : bit (4) >
‘0000'B
< Message type : bit (8) >
‘0000 0111’B
< SI2 quarter Rest Octets >
< BA_IND : bit >
0
< 3G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1 Signal strength | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.1 Definition | The MS reports RXLEV values related to the apparent received RF signal strength. It is necessary for these levels to attain sufficient accuracy for the correct functioning of the system. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.2 Conformance requirement | 1. The RMS received signal level at the receiver input shall be measured by the MS over the full range of ‑110 dBm to ‑48 dBm with a relative accuracy between signals with levels up to 20 dB difference according to table 21‑1
1.1 under normal conditions, 3GPP TS 05.08, subclause 8.1.2 and 3GPP TS 05.05, subclause 6.2.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.3 Test purpose | 1. To verify that the RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N reported by the MS does not exceed conformance requirement 1.
1.1 under normal conditions;
1.2 under extreme conditions.
2. To verify that the RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N reported by the MS does not exceed conformance requirement 2 under norma... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.4.1 Initial conditions | The SS is set to produce the BCCH of the serving cell at 63 dBVemf( ) and the BCCHs of 6 surrounding cells at 28 dBVemf( ). The BCCH of the serving cell indicates these BCCHs, but not the BCCH of the serving cell. The ARFCN of the serving cell BCCH is chosen so as not to interfere with the other channels as shown in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.4.2 Procedure | a) The levels of the TCH / PDTCH and BCCHs are set according to table 21-2 step 1. The SS waits 20 s before continuing.
Table 21-2: Signal levels at receiver input in dBVemf( )
ARFCN
TCH / PDTCH
BCCH1
BCCH2
BCCH3
BCCH4
BCCH5
BCCH6
Step
GSM 450
259
276
293
264
269
281
288
GSM 480
306
323
340
311
316
328
335
GSM 900:
1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.5 Test requirements | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.5.1 Relative accuracy of measurements on different ARFCN | For normal and each of the 4 extreme conditions tested the following applies:
a) For each of the steps 1, 21, 22, 42, 43 and 64, of the 7 reported RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N values checked, the difference between the minimum reported RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N value and the maximum reported ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.5.2 Relative accuracy at a single frequency (BCCH1) | For normal and each of the 4 extreme conditions tested the following applies:
For: n <= 21 and RXLEV1 / RXLEV_N1 = 63
RXLEVn / RXLEV_N1 - (63 - n + r) shall be between:
‑2 and +2
NOTE 1: This formula allows for an MS with an absolute accuracy worse than +0,5 dB and therefore reporting an RXLEV / RXLEV_N of 63 for more... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.1.5.3 Absolute accuracy | For each BCCH reported, |RXLEVMS + m 10 - 62|/ |RXLEV_NMS + m 10 - 62| shall be no more than:
4 for steps 64 and 85 under normal conditions.
6 for steps 64 and 85 under extreme conditions.
6 for steps 1, 22 and 43 under normal and extreme conditions.
where: 0 m 4 as identified in table 21‑2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2 Signal strength selectivity | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.1 Definition | The signal strength selectivity is a measure of the ability of the signal strength measuring part of the MS to discriminate against RF power from adjacent ARFCN. The RXLEV selectivity figure corresponds to the amount by which the adjacent channel power shall be attenuated. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.2 Conformance requirement | The selectivity of the received signal measurement shall be as follows:
- for adjacent (200 kHz) channel; 16 dB;
- for adjacent (400 kHz) channel; 48 dB;
- for adjacent (600 kHz) channel; 56 dB.
3GPP TS 05.08, subclause 8.1.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.3 Test purpose | To verify that the MS meets the conformance requirement at the 200 kHz adjacent channel above and below the wanted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.4.1 Initial conditions | For GSM 450:
For circuit switch capable devices, a call is set up according to the generic call set up procedure on ARFCN 269 and with surrounding cell BCCH3 indicated in the BA list at ARFCN 281.
For GPRS only devices, the Ready Timer (T3314) is indicated as disabled in the GMM ATTACH ACCEPT message. A GPRS mode RLC ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.4.2 Procedure | a) The SS records the RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N values reported for the TCH / PDTCH and BCCH3
b) BCCH1 and 2 are set to 9 dB above the signal level of the TCH / PDTCH and BCCH3
NOTE: The first adjacent channel interference requirement limits the level of BCCHs 1 and 2 to 9 dB. This ensures that the MS can... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.2.5 Test requirements | The values of RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N recorded in step d) shall be no more than 1 above the values recorded in step a).
NOTE: This one change in the reported value of RXLEV (or RXLEV_SERVING_CELL) / RXLEV_N is calculated as follows: The level of the first adjacent interfering signal is such that C/I is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3 Signal quality under static conditions | In order to have a testing performance corresponding to that in clause 14 for high error rates, the multiplication factor of the tested error rate with respect to the specified error rate have been increased. The following figures have been used (static propagation conditions):
Specified error rate
Multiplication facto... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1 Signal quality under static conditions - TCH/FS no DTX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.1 Definition | The MS must be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS has to map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set of frames, eight levels of RXQUAL are define... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.3 Test purpose | 1. To verify, under static propagation conditions, that the received signal quality is measured and mapped to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.4.1 Initial conditions | A call is set up by the SS according to the generic call set up procedure on a full rate speech channel in the mid ARFCN range. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Full rate
The SS commands the MS to establish the TCH burst-by-burst loop... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.4.2 Procedure | a) The SS sets the level of the unwanted signal at a value for which the BER of the looped back bursts, averaged over the reporting period as defined in 3GPP TS 05.08, subclause 8.4 is covered by one of the cases 1 to 13 of table 21.3.1.5.
b) The SS verifies that the MS reports RXQUAL and whether or not the reported le... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.1.5 Test requirements | The sets of test results for sample counter (i) and event counter (i) should be combined as follows.
sum i=0..14 ((event counter i * 100) / test limit i)
-----------------------------------------------------------
sum i=0..14 (sample counter i)
A result of <1 is a pass, >=1 is a fail
Table 21.3.1.5: Test criteria and l... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2 Signal quality under static conditions - TCH/HS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.1 Definition | The MS shall be capable of measuring the received signal quality, which is specified in terms of bit error ratio (BER) before channel decoding averaged over the reporting period of length of one SACCH multiframe defined in subclause 8.4 of 3GPP TS 05.08. The MS shall map this BER into RXQUAL values using the coding sch... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.2 Conformance requirement | 1. The received signal quality shall be measured by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe. When the quality is assessed over the full-set and sub-set of frames, eight levels of RXQUA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.3 Test purpose | 1. To verify, under static propagation conditions, that the received signal quality is measured and mapped to the eight levels of RXQUAL_FULL by the MS in a manner that can be related to an equivalent average BER before channel decoding (i.e. chip error ratio), assessed over the reporting period of one SACCH multiframe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 21.3.2.4.1 Initial conditions | A call is set up by the SS according to the generic call set up procedure on a half rate speech channel in the mid ARFCN range. The RADIO_LINK_TIMEOUT parameter value is set to maximum.
Specific PICS Statements:
-
PIXIT Statements:
- Loop C delay Half rate
The SS commands the MS to establish the TCH burst-by-burst loop... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.