hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.16.5 Test requirement | For each error code, the ME shall give an appropriate MMI indication. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17 Electrical tests | General test purpose
Testing of electrical characteristics of the SIM/ME interface.
Whilst non-conformance in this area would be unlikely to cause difficulties to other users or the network (type approval criteria), significant deviations from the specifications (3GPP TS 11.11 and ISO 7816) may damage the SIM. If an at... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1 Test of the power transition phases | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1 Phase preceding ME power on | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.1 Definition | When the mobile equipment is switched off, the contacts of the SIM/ME interface remain in an inactive state in order to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.2 Conformance requirement | The residual voltage across the contacts of the SIM/ME interface (C1, C2, C3, C6, C7) shall not exceed ± 0,4 Volts referenced to GND.
Reference:
3GPP TS 11.11, subclause 4.3.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.3 Test purpose | To verify that the residual voltage across the contacts of the SIM/ME interface (C1, C2, C3, C6, C7) is not greater than ± 0,4 Volts referenced to GND. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.4.1 Initial condition | The ME is connected to a SIM Simulator.
The contact C1 (Vcc) of the SIM/ME interface is loaded with an impedance of 10 kOhm.
The other contacts (C2, C3, C6, C7) are loaded with an impedance of 50 kOhm. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.4.2 Procedure | The residual voltage on each contact is measured. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.1.5 Test requirement | The residual voltage on each contact shall not exceed ±0,4 Volts referenced to GND. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2 Phase during SIM power on | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.1 Definition | When the mobile station is switched on or when the SIM/ME interface is being activated after 3V/5V or 1,8V/3V switching, the contacts shall be activated in a defined sequence in order to prevent any damage to the SIM.
The timing of this sequence is not defined, a measurement resolution better than or equivalent to 100 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.2 Conformance requirement | a) When the MS is soft powered on, the contacts of the SIM/ME interface shall be activated in the following order:
1. VCC at state H and stable;
2. CLK stable;
3. RST at state L for at least 400 clock cycles after the clock signal is applied to CLK;
4. I/O at state Z within 200 clock cycles after the clock signal i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.3 Test purpose | To verify that the contacts of the SIM/ME interface are activated in the correct order, as described in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.4.1 Initial condition | The ME is connected to a SIM Simulator. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.4.2 Procedure | To test the requirements a), b), c.1), d) and e.1) the MS is soft powered on.
To test the requirement c.2) and e.2), the ME is caused to switch the voltage on the SIM/ME interface.
The verification of each activation procedure starts with the first contact leaving the inactive state. The SIM/ME interface is monitored u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.2.5 Test requirement | The contacts of the SIM/ME interface shall be activated in the correct order, as described in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3 Phase during ME power off with clock stop forbidden | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.1 Definition | When the mobile station is soft powered off, the contacts shall be deactivated in a defined sequence in order to prevent any damage to the SIM.
The timing of this sequence is not defined, a measurement resolution better than or equivalent to 100 ns is assumed.
NOTE 1: If during MS operation the SIM is physically remove... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.2 Conformance requirement | a) When the ME is soft powered down, the contacts of the SIM/ME interface shall be deactivated in the following order:
1. RST at low state;
2. Clock stopped at low state;
3. Vpp inactive (only if Vpp is provided independent of Vcc, see 3GPP TS 11.11 subclause 5.3);
4. I/O at state A;
5. Vcc inactive.
b) When Vpp is con... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.3 Test purpose | To verify that the contacts of the SIM/ME interface become deactivated in the correct order, as given in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.4.1 Initial condition | The ME is connected to a SIM Simulator.
The file characteristics of the directories (byte 14 of STATUS information) shall indicate a 5V SIM with clock stop forbidden. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.4.2 Procedure | The MS is soft powered off.
The SIM/ME interface is monitored until it is fully deactivated. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.3.5 Test requirement | The contacts of the SIM/ME interface shall be deactivated in the correct order, as given in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4 Phase during ME power off with clock stop allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.1 Definition | When the mobile station is soft powered off or when the SIM/ME interface is being deactivated for 3V/5V or 1,8V/3V switching, the contacts shall be deactivated in a defined sequence in order to prevent any damage to the SIM.
The timing of this sequence is not defined, a measurement resolution better than or equivalent ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.2 Conformance requirement | a) Depending on the state of the clock at the time of deactivation, the contacts of the SIM/ME shall be deactivated in one of two ways.
If the clock is running, the contacts of the SIM/ME interface shall be deactivated in the following order:
1. RST at low level;
2. Clock stopped at low level;
3. Vpp inactive (only if ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.3 Test purpose | To verify that, depending on the state of the clock (running or stopped), the contacts of the SIM/ME interface become deactivated in the correct order, as given in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.4.1 Initial condition | The ME is connected to a SIM Simulator.
The file characteristics of the directories (byte 14 of STATUS information) shall indicate that clock stop is allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.4.2 Procedure | To test the requirements a), b), c.1), d) and e.1), the MS is soft powered off.
To test the requirement c.2) and e.2), the ME is caused to switch the voltage on the SIM/ME interface.
The SIM/ME interface is monitored until it is fully deactivated. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.4.5 Test requirement | The contacts of the SIM/ME interface shall be deactivated in the correct order, as given in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5 SIM Type Recognition and Voltage Switching | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1 Reaction of 3V only MEs on SIM type recognition failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.1 Definition | When a 3V only ME detects a failure during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE".
2) If a 3V only ME cannot complete the SIM type recog... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.3 Test purpose | 1) To verify that a 3V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 3V only ME deactivates the SIM/ME interface and rejects the SIM in case that the SIM does not respond to the "STATUS/GET RESPONSE" command. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM with nominal test conditions according to table 27.2‑2. All elementary files are coded as default.
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator does not respond to the "STATUS/GET RESPONSE" command.
The SIM/ME interface is monitored for at least 1 minute until the MS is swit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.1.5 Test requirement | 1) Immediately after the ATR only the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 3V only ME shall deactivate the SIM/ME interface within 5 s and reject the SIM (i.e. not activate the SIM/ME interface within the test procedure). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2 Reaction of 3V only MEs on type recognition of 5V only SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.1 Definition | When a 3V only ME detects a 5V only SIM during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE"
2) If a 3V only ME identifies a 5V only SIM during the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.3 Test purpose | 1) To verify that a 3V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 3V only ME deactivates the SIM/ME interface and rejects the SIM if a 5V only SIM is applied. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM (to ensure that the ME can perform the SIM type recognition procedure) with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "0" (i.e. 5V only SIM).
The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 5V only SIM.
The SIM/ME interface is monitored... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.5 Test requirement | 1) Immediately after the ATR only the two command "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 3V only ME shall deactivate the SIM/ME interface immediately after receipt of the status information from the SIM (but not later than 5 s after the "STATUS/GET RESPONSE command) and reject the SIM (i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3 Reaction of 3V technology MEs on type recognition of 5V only SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.1 Definition | When a 3V technology ME detects a 5V only SIM during the SIM type recognition procedure, the ME shall switch to 5V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.2 Conformance requirement | 1) A 3V technology ME shall initially activate the SIM at 3V (i.e. the first activation of a GSM card session.
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR procedure and before issuing any other command. The procedure shall ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.3 Test purpose | 1) To verify that a 3V technology ME initially activates the SIM with 3V.
2) To verify that a 3V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 3V technology ME deactivates the SIM/ME interface immediately after the SIM type recognition procedure (in order to switch the supply ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 5V only SIM with nominal test conditions according to table 27.2‑1. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "0" (i.e. 5V only SIM).
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 5V only SIM.
The SIM/ME interface is monitored... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 3V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME before issuing further commands.
3) The 3V technology ME shall deactivate the SIM/ME interface immediately after recei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4 Reaction of 3V technology MEs on type recognition of 3V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.1 Definition | When a 3V technology ME detects a 3V technology SIM during the SIM type recognition procedure the ME may either switch to 5V operation or stay in 3V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.2 Conformance requirement | 1) A 3V technology ME shall initially activate the SIM with a 3V (i.e. the first activation of a GSM card session).
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. the procedure shall consi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.3 Test purpose | 1) To verify that a 3V technology ME initially activates the SIM with 3V.
2) To verify that a 3V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 3V technology ME deactivates the SIM/ME interface immediately after the recognition of a 3V technology SIM (in order to switch the sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "1" (i.e. 3V technology SIM.)
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is monitor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.27.1.5.4.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 3V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE: shall be sent by the ME.
3) The ME shall react in one of the following ways:
a) The ME deactivates the SIM/ME interface immediately after the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5 Reaction of 1,8V only MEs on SIM type recognition failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.1 Definition | When a 1,8V only ME detects a failure during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE".
2) If a 1,8V only ME cannot complete the SIM type rec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.3 Test purpose | 1) To verify that a 1,8V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 1,8V only ME deactivates the SIM/ME interface and rejects the SIM in case that the SIM does not respond to the "STATUS/GET RESPONSE" command. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM with nominal test conditions according to table 27.2‑3. All elementary files are coded as default.
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator does not respond to the "STATUS/GET RESPONSE" command.
The SIM/ME interface is monitored for at least 1 minute until the MS is swit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.5 Test requirement | 1) Immediately after the ATR only the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 1,8V only ME shall deactivate the SIM/ME interface within 5 s and reject the SIM (i.e. not activate the SIM/ME interface within the test procedure). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6 Reaction of 1,8V only MEs on type recognition of 3V SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.1 Definition | When a 1,8V only ME detects a 3V technology SIM during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM.
. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE"
2) If a 1,8V only ME identifies a 3V technology SIM du... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.3 Test purpose | 1) To verify that a 1,8V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 1,8V only ME deactivates the SIM/ME interface and rejects the SIM if a 3V technology SIM is applied. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM (to ensure that the ME can perform the SIM type recognition procedure) with nominal test conditions according to table 27.2‑3. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "01" (i.e. 3V tec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is mon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.5 Test requirement | 1) Immediately after the ATR only the two command "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 1,8V only ME shall deactivate the SIM/ME interface immediately after receipt of the status information from the SIM (but not later than 5 s after the "STATUS/GET RESPONSE command) and reject the SIM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7 Reaction of 1,8V technology MEs on type recognition of 3V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.1 Definition | When a 1,8V technology ME detects a 3V technology SIM during the SIM type recognition procedure, the ME shall switch to 3V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.2 Conformance requirement | 1) A 1,8V technology ME shall initially activate the SIM at 1,8V (i.e. the first activation of a GSM card session.
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR procedure and before issuing any other command. The procedure sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.3 Test purpose | 1) To verify that a 1,8V technology ME initially activates the SIM with 1,8V.
2) To verify that a 1,8V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 1,8V technology ME deactivates the SIM/ME interface immediately after the SIM type recognition procedure (in order to switch the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "01" (i.e. 3V technology SIM).
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is mon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 1,8V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME before issuing further commands.
3) The 1,8V technology ME shall deactivate the SIM/ME interface immediately after r... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8 Reaction of 1,8V technology MEs on type recognition of 1,8V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.1 Definition | When a 1,8V technology ME detects a 1,8V technology SIM during the SIM type recognition procedure the ME may either switch to 3V operation or stay in 1,8V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.2 Conformance requirement | 1) A 1,8V technology ME shall initially activate the SIM with a 1,8V (i.e. the first activation of a GSM card session).
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. the procedure shall c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.3 Test purpose | 1) To verify that a 1,8V technology ME initially activates the SIM with 1,8V.
2) To verify that a 1,8V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 1,8V technology ME deactivates the SIM/ME interface immediately after the recognition of a 1,8V technology SIM (in order to swit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM with nominal test conditions according to table 27.2‑3. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "11" (i.e. 1,8V technology SIM.)
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 1,8V technology SIM.
The SIM/ME interface is monit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 1,8V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE: shall be sent by the ME.
3) The ME shall react in one of the following ways:
a) The ME deactivates the SIM/ME interface immediately after th... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.