hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_Add... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.2 SoLSA signalling / structured procedures / MS originated call / late assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.2.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initia... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.2.2 Test purpose | To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile originating call (MOC) with late assignment procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.3 SoLSA signalling / structured procedures / MS terminated call / early assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.3.1 Conformance requirement | 1) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after Layer 2 UA message sent from the network.
2) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.3.2 Test Purpose | To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile terminated call (MTC) with early assignment procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_Add... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.4 SoLSA signalling / structured procedures / MS terminated call / late assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.4.1 Conformance requirement | 1) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after Layer 2 UA message sent from the network.
2) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.4.2 Test Purpose | To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile terminated call (MTC) with late assignment procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.4.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_Add... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.5 SoLSA signalling / structured procedures / emergency call / idle updated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.5.1 Conformance requirements | 1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.5.2 Test purpose | To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during an Emergency Call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.5.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.6 SoLSA signalling / structured procedures / emergency call / idle, no IMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.6.1 Conformance requirements | 1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.6.2 Test purpose | To verify that the SoLSA MS in the "idle, no IMSI" state (no SIM inserted), supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during an Emergency Call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.15.5.6.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI" no SIM inserted.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.0 Default contents of layer 3 messages for AMR signalling tests | Refer to table 26.6. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.2 Inband Signalling, Uplink Codec Adaptation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.2.1 Conformance Requirement | The MS shall after reception of a Codec Mode Command apply the corresponding codec mode in the uplink direction for the next possible speech frame and no more than three speech frames later. This test is not intended to verify these conformance requirements, but to verify the correctness of the involved layer 1 and lay... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.2.2 Test Purpose | This test is concerned with the link adaptation for AMR uplink and the related inband signalling. The test shall verify that the MS in the uplink direction applies the codec mode indicated by the network transmitted Codec Mode Commands, and that the MS correctly signals the used codec as Codec Mode Indication in the up... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.2.3 Method of Test | Initial Conditions
The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
a) A mobile originated call is initiated, following the CHANNEL REQUEST rec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.3 Structured procedures / MS terminated call / early assignment / no initial codec mode | NOTE: This test is derived from the one described in subclause 26.12 and entitled: "Structured procedures / MS terminated call / early assignment" |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.3.1 Conformance requirement | 1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminating call establishment with e... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.3.2 Test purpose | 1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminatin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.3.3 Method of Test | Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.4 Structured procedures / MS originated call / late assignment / specified initial codec mode | NOTE: This test is derived from the one described in subclause 26.12 and entitled: "Structured procedures / MS terminated call / early assignment". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.4.1 Conformance requirement | 1) The MS shall indicate and include in the mobile originating SETUP for speech call all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message using full rate version 3 or half rate version 3, the Mobile Station starts a normal channel assignment procedure. It means that the MS initiat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.4.2 Test purpose | 1) To verify that the MS indicates and includes in the mobile originating SETUP for speech call all the speech versions that it supports.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.4.3 Method of Test | Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
- Way to indicate mobile originated alerting.
Foreseen Final State of MS
The MS has a MO call in state U10, "active"... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.5 AMR signalling / Handover / active call / successful case | NOTE: This test is derived from 26.12.2 – EFR Signalling/Handover/active call/successful case. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.5.1 Conformance requirements | The MS shall correctly apply the handover procedure in the non-synchronised case when:
- a call is in progress; and
- handover is performed from a TCH/F with/without frequency hopping towards a TCH/F with/without frequency hopping;
- the mode of either the current or the target channel is set to full rate speech versi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.5.2 Test Purpose | To test that the MS shall correctly apply the handover procedure in the non-synchronized case when:
- a call is in progress; and
- handover is performed from a TCH/F with/without frequency hopping towards a TCH/F with/without frequency hopping; and
- the mode of either the current or the target channel is set to full r... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.6 Structured procedures / emergency call | NOTE: this test is derived from subclause 26.15.5 - Structured procedures / emergency call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.6.1 Conformance requirement | 1) The MS in the "idle, updated" state, after a successful location update, the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.6.2 Test purpose | 1) To verify that an MS supporting speech in the MM state "idle, updated", when made to call the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL RE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.7 AMR Signalling / Directed Retry / Mobile Originated Call | NOTE: This test is derived from the one defined in subclause 26.12.6 and entitled "EFR Signalling / Directed Retry / Mobile Originated Call". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.7.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (no frequency hopping) to TCH/AMR with frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "mobile originating call proceeding" state shall, upon receipt of a CONNECT message... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.7.2 Test purpose | To test that, when the MS is ordered to perform a non-synchronized handover after the CALL PROCEED message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.7.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
NCC_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.8 AMR Signalling / Directed Retry / Mobile Terminated Call | NOTE: This test is derived from the one defined in subclause 26.12.7 and entitled "EFR Signalling / Directed Retry / Mobile Terminated Call". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.8.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 with frequency hopping to TCH/AMR with frequency hopping and starting time in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "call delivered" state shall, if the MS supports immediate connec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.8.2 Test purpose | To test that when the MS is ordered to perform a non-synchronized handover after the CALL CONFIRM message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.8.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation =See the table below. PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
NCC_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9 AMR RATSCCH Protocol | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.1 AMR Configuration Change (normal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.1.1 Conformance requirements | The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.1.2 Test purpose | This test will verify that the MS is able to handle a properly formatted AMR_CONFIG_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.1.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.2 AMR Configuration Change (abnormal) | 26.16.9.2.1 Conformance requirements
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.2.2 Test purpose | This test will verify that the MS is able to handle an improperly formatted AMR_CONFIG_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.2.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.3 Codec Mode Phase Change (normal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.3.1 Conformance requirements | The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.3.2 Test purpose | This test will verify that the MS can correctly handle a properly formatted CMI_PHASE_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.3.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.4 Codec Mode Phase Change (abnormal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.4.1 Conformance requirements | The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is n... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.4.2 Test purpose | This test will verify that the MS can correctly handle an improperly formatted CMI_PHASE_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.4.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.5 Threshold Change (normal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.5.1 Conformance requirements | The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direct... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.5.2 Test purpose | This test will verify that an RATSCCH capable MS is able to handle a properly formatted THRESH_REQ message |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.5.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.6 Threshold Change (abnormal) | 26.16.9.6.1 Conformance requirements
The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.6.2 Test purpose | This test will verify that an RATSCCH capable MS is able to handle an improperly formatted THRESH_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.6.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.7 Unknown RATSCCH REQ Message | 26.16.9.7.1 Conformance requirements
The ACK_UNKNOWN message serves as an acknowledgement that a RATSCCH REQ message has been detected and correctly decoded, but was unknown to the Addressee.
Reference:
3GPP TS 05.09 sub-clause: 3.2.2.3.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.7.2 Test purpose | This test will verify that the MS can correctly handle an unknown RATSCCH REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.7.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.8 Ignore subsequent REQ prior to expiry of REQ_Activation counter | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.8.1 Conformance requirements | If another REQ message is received by the MS before the REQ_Activation counter has elapsed, the MS shall ignore the message.
Reference:
3GPP TS 45.009 sub-clause: 3.2.2.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.8.2 Test purpose | This test will verify that the MS ignores a REQ message which is received before the REQ_Activation counter has elapsed. The test will verify that both the following conditions are satisfied:
- the MS ignores a subsequent REQ message received after it has sent the ACK_OK but before the REQ_Activation counter has elapse... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.8.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.9 Initiation of Transaction with ACK_ERR or ACK_UNKNOWN | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.9.1 Conformance requirements | If at either side an ACK_ERR or ACK_UNKNOWN is received although no corresponding REQ has been sent before, the ACK message shall be ignored.
Reference:
3GPP TS 45.009 sub-clause: 3.2.2.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.9.2 Test purpose | This test will verify that the MS ignores any ACK_ERR or ACK_UNKNOWN which is received without a corresponding REQ having been sent. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.9.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.10 Inversion of the Phase of the CMR/CMI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.10.1 Conformance requirements | The phase of the Codec Mode Indication in the downlink can be changed during a call by using a CMI_PHASE_REQ message sent on the RATSCCH.
The CMI_PHASE_REQ message may be sent by the BTS during a call to change the phase of the Codec Mode Indication in the downlink without interruption of the speech transmission.
The A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.10.2 Test purpose | This test shall verify that the MS is able to change the phase of the Codec Mode Indication in the downlink using the RATSCCH protocol. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.10.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.11 Change of Active Codec Set | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.11.1 Conformance requirements | AMR codec mode adaptation is done within a set of 4 codec modes. The codec mode set (Active Codec Set) to be used by the BSS and the MS is defined during call setup and/or handover by layer 3 signalling. The ACS can be changed during a call using an AMR_CONFIG_REQ message sent on the RATSCCH.
The AMR_CONFIG_REQ message... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.11.2 Test purpose | This test shall verify that the MS is able to change its Active Codec Set using the RATSCCH protocol, with change of thresholds, and with non-specification of thresholds. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.11.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI al... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.9.12 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10 AMR signalling/ test of the channel mode modify procedure | NOTE: This test is derived from the test in sub-clause 26.12.1 entitled "EFR signalling / Test of the channel mode modify procedure ". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.1 AMR signalling/ test of the channel mode modify procedure/ full rate | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.1.1 Conformance requirement | The MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6.1.1 and 3.4.6.1.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.1.2 Test purpose | To verify that the MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.1.3 Method of test | Initial Conditions
System Simulator: 1 cell, default parameters.
Mobile Station: The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
-.
PIXIT statements:
-.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test procedure
A Mobile Terminated call is initiated, however following t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.2 AMR signalling/ test of the channel mode modify procedure/ half rate | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.2.1 Conformance requirement | The MS with a TCH/H allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6.1.1 and 3.4.6.1.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.16.10.2.2 Test purpose | To verify that the MS with a TCH/H allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.