hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.3.1 Conformance requirements | The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.3.2 Test purpose | This test will verify that the MS can correctly handle a properly formatted CMI_PHASE_REQ message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.3.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Support of GSM speech full rate version 4 (O-TCH/WFS).
- Support of GSM speech Half rate version 4 (O-TCH/WHS).
- Support of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.4 Reserved for future use | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.5 Threshold Change (normal) | NOTE: this test is derived from the one described in subclause 26.16.9.5 and entitled: “Threshold Change (normal)" |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.5.1 Conformance requirements | The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direct... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.5.2 Test purpose | This test will verify that an RATSCCH capable MS is able to handle a properly formatted THRESH_REQ message |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.5.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Support of GSM speech full rate version 4 (O-TCH/WFS).
- Support of GSM speech Half rate version 4 (O-TCH/WHS).
- Support of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.6 Reserved for future use | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.7 Reserved for future use | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.8 Reserved for future use | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.9 Reserved for future use | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.10 Inversion of the Phase of the CMR/CMI | NOTE: this test is derived from the one described in subclause 26.16.9.10 and entitled: “Inversion of the Phase of the CMR/CMI" |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.10.1 Conformance requirements | The phase of the Codec Mode Indication in the downlink can be changed during a call by using a CMI_PHASE_REQ message sent on the RATSCCH.
The CMI_PHASE_REQ message may be sent by the BTS during a call to change the phase of the Codec Mode Indication in the downlink without interruption of the speech transmission.
The A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.10.2 Test purpose | This test shall verify that the MS is able to change the phase of the Codec Mode Indication in the downlink using the RATSCCH protocol. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.10.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Support of GSM speech full rate version 4 (O-TCH/WFS).
- Support of GSM speech Half rate version 4 (O-TCH/WHS).
- Support of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.11 Change of Active Codec Set | NOTE: this test is derived from the one described in subclause 26.16.9.11 and entitled: "Change of Active Codec Set” |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.11.1 Conformance requirements | AMR codec mode adaptation is done within a set of 4 codec modes. The codec mode set (Active Codec Set) to be used by the BSS and the MS is defined during call setup and/or handover by layer 3 signalling. The ACS can be changed during a call using an AMR_CONFIG_REQ message sent on the RATSCCH.
The AMR_CONFIG_REQ message... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.11.2 Test purpose | This test shall verify that the MS is able to change its Active Codec Set using the RATSCCH protocol, with change of thresholds, and with non-specification of thresholds. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.9.11.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Support of GSM speech full rate version 4 (O-TCH/WFS).
- Support of GSM speech Half rate version 4 (O-TCH/WHS).
- Support of... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.10 AMR signalling/ test of the channel mode modify procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.10.1 WB AMR signalling test of the channel mode modify procedure / full rate | NOTE: this test is derived from the one described in subclause 26.16.10.1 and entitled: "AMR signalling/ test of the channel mode modify procedure/full rate” |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.10.1.1 Conformance requirement | The MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6.1.1 and 3.4.6.1.2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.10.1.2 Test purpose | To verify that the MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.19.10.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
- Support of GSM speech full rate version 4 (O-TCH/WFS).
- Support of GSM Speech Full Rate version 5 (TCH/WFS).
PIXIT statements:
-
Foreseen Final State of the MS
"Id... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.20 Enhanced Power Control | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.20.1 Enhanced Power Control / MS Supports EPC | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.20.1.1 Conformance requirements | The purpose of the Mobile Station Classmark 3 information element is to provide the network with information concerning aspects of the mobile station. The contents might affect the manner in which the network handles the operation of the mobile station. The Mobile Station Classmark information indicates general mobile ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.20.1.2 Test purpose | To verify that a MS that supports EPC indicates to the network that it supports GERAN feature package 2.
To verify that when commanded to do so the MS shall configure the assigned TCH or O-TCH channel in EPC mode.
To verify that when on a channel in EPC mode the MS ignores the EPC Uplink Power Control command if the si... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.20.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters except IMSI Attach-detach shall be applied.
Mobile Station:
MS is switched off.
Specific PICS Statements:
-
PIXIT Statements:
-
Test Procedure
The MS is switched on (or its power is re-applied). After the start of the LOCATION UPDATING procedure the SS ini... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21 VAMOS Signalling | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.0 General | VAMOS signalling test cases in this section are performed with SCPIR = 0 if not otherwise defined in the test case.
VAMOS signalling test cases are performed in VAMOS I mode for MS supporting VAMOS I, VAMOS II mode for MS supporting VAMOS II and in VAMOS III mode for MS supporting VAMOS III. VAMOS II and VAMOS III mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.1 VAMOS Signalling / MS originated call FR / TSC assignment in ASSIGNMENT COMMAND | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.1.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.1.2 Test purpose | To verify for MO call setup procedure that the MS applies the correct VAMOS TSC set allocated by ASSIGNMENT COMMAND message for full rate speech channels. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.1.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters, TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- VAMOS II supported ( TSPC_VAMOS_Type2)
- VAMOS III supported (TSPC_VAMOS_Type3)
- Spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.2 VAMOS Signalling / MS Terminated call / Channel mode assignment in Channel Mode Modify | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.2.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 TSC Set 1 shall be used | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 TSC Set 2 shall be used | All other values are reserved.
References
3GPP TS 45.001 subclause 13.1.
3GPP TS 44.018 subclauses 10.5.2.5
3GPP TS 44.060 subclauses 7.1, 8.9.2.1
3GPP TS 45.002 subclauses 6.4.2.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.2.2 Test purpose | To verify for MT call setup procedure that the MS applies the correct VAMOS TSC Set allocated by IMMEDIATE ASSIGNMENT message also check that channel mode modify configure a VAMOS II and VAMOS III channel correctly. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.2.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters, TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- VAMOS II supported ( TSPC_VAMOS_Type2)
- VAMOS III supported (TSPC_VAMOS_Type3)
- Spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.4 VAMOS Signalling / MS terminated call / Handover to VAMOS mode | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.4.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.4.2 Test purpose | To verify for mobile terminated call setup procedure (late assignment) and handover procedure that the MS applies correctly the assigned VAMOS TSC set. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.4.3 Method of Test | Initial Conditions
System Simulator:
2 cells, default parameters.
Cell A: TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Cell B: TSC as defined in table 26.21-1 Cell B TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.5 VAMOS Signalling / MT VAMOS call / TSC assignment in DTM Assignment Command | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.5.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.5.2 Test purpose | To verify that a VAMOS mobile is able to operate in DTM mode and packet data traffic channels together with associated control channels shall have the same TSC as TSC of the traffic channel together with associated control channels and shall be selected from TSC set 1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.5.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters, DTM supported, TSC as defined in table 26.21-1 Cell A TSC set.
Mobile Station:
MS is GPRS attached and PDP Context 2 activated.
Specific PICS statements:
- VAMOS II supported ( TSPC_VAMOS_Type2)
- VAMOS III supported (TSPC_VAMOS_Type3)
PIXIT statements:
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6 VAMOS Signalling / MS originated call / Handover between different traffic rates | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.2 Test purpose | To verify that during a mobile originated call, the MS applies TSC set and different channel rates during handover from VAMOS to non VAMOS mode |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.3 Method of Test | Initial Conditions
System Simulator:
2 cells, default parameters.
Cell A: TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Cell B: TSC as defined in table 26.21-1 Cell B TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7 VAMOS Signalling / Emergency call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.2 Test purpose | To verify for emergency call setup procedure that the MS applies the correct VAMOS TSC set allocated by ASSIGNMENT COMMAND message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters, TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- VAMOS II supported ( TSPC_VAMOS_Type2)
- VAMOS III supported (TSPC_VAMOS_Type3)
- Spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8 VAMOS Signalling / MS Originated call / Early assignment / Handover to different AMR codec rates | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.2 Test purpose | To verify that during a mobile originated call and after handover procedure the MS applies TSC set and different AMR codec rates in VAMOS mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.3 Method of Test | Initial Conditions
System Simulator:
2 cells, default parameters.
Cell A: TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Cell B: TSC as defined in table 26.21-1 Cell B TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22 Test of other features | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1 Layer 2 fill bits randomisation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.1 Conformance requirements | The end of the useful part of the frame, i.e. the octets following the length indicator field in type A frames and the octets following the information field in type B frames, is determined by a length indicator contained in the length indicator field. The useful part of a Bbis frames takes all N201 octets of that fram... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.2 Test purpose | An MS shall correctly decode all LAPDm frames with randomised fill bits.
An MS supporting randomisation of fill bits in the Uplink direction shall a) correctly encode the first octet of a frame containing fill bytes and b) send a random sequence of bits during a signalling sequence. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is switched off.
Specific PICS statements:
- L2 fill bits randomisation in uplink (TSPC_UL_L2_Fill_Bits_Randomisation)
- at least one short message service (TSPC_AddInfo_SMS)
- MSsupporting at least one bearer capability service (TS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1 MS identification by short IMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1 MS identification by short IMSI - Normal case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.1 Definition | The IMSI is used for unique identification of the MS by a GSM network. The IMSI is stored in the SIM and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the IMSI of the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.2, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.3 Test purpose | 1) To verify that the ME uses the IMSI of the SIM.
2) To verify that the ME can handle an IMSI of less than the maximum length. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 246
LAI-MNC 81 or 813 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is installed into the ME and the MS is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the IMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the IMSI stored in the SIM.
27.1.1a MS identification by short IMSI - for GPRS
27.1.1a.1 Definition
The IMSI is used for unique identification of the MS by a GSM network. The IMSI is stored in the SIM and read during the SIM/ME initialization procedur... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2 MS identification by short IMSI, Phase 1 DCS SIM | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.1 Definition | Different from Phase 2, the IMSI in a Phase 1 DCS SIM is stored in a directory DFDCS1800 with the specific identifier "7F 21". To ensure backwards compatibility, if selection of the phase 2 identifier "7F 20" fails, the MS shall select "7F 21". Otherwise access to the IMSI and other data is impossible with a Phase 1 DC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.3 Test purpose | To verify that the ME uses the identifier "7F 21" to select DFDCS1800 in a Phase 1 DCS SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI (MCC/MNC/LAC): 246/81/0001.
Access control: unrestricted.
A phase 1 DCS SIM (identifier of DFDCS1800 is "7F 21", DFGSM not existing) with default values is installed into the ME and the MS is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the IMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the IMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2 MS identification by short TMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.1 Definition | The TMSI is temporarily used for identification of the MS by a GSM network. It will have been previously assigned by the network. The TMSI is stored in the SIM by the ME and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the TMSI stored in the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.5, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.3 Test purpose | 1) To verify that the ME uses the TMSI stored in the SIM.
2) To verify that the ME can handle a TMSI of less than maximum length. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 246
LAI-MNC 81 or 813 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is used with the following exception.
EFLOCI (Location Information)
Logically: LAI-MCC: 246
LAI-MNC: 81 or 813 (See Note 0... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the TMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the TMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3 MS identification by long TMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.1 Definition | The TMSI is temporarily used for identification of the MS by a GSM network. It will have been previously assigned by the network. The TMSI is stored in the SIM by the ME and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the correct TMSI stored in the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.5, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.3 Test purpose | 1) To verify that the ME uses the TMSI stored in the SIM.
2) To verify that the ME can handle a TMSI of maximum length.
3) To verify that the ME does not respond to page requests containing a previous TMSI. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4.1 Initial conditions | Prior to this test, the ME shall have been operated with a SIM containing TMSI "2143". This will be achieved by executing the previous test (27.2) prior to this test. Only under this condition will test be verified.
The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the TMSI "2143".
b) The SS sends PAGING REQUEST to the MS using the TMSI stored in the SIM.
c) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
d) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.5 Test requirement | 1) After step a) the MS shall not respond to the PAGING REQUEST.
2) After step c) the MS shall send PAGING RESPONSE to the SS containing the TMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4 MS identification by long IMSI, TMSI updating and cipher key sequence number assignment |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.