hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM (to ensure that the ME can perform the SIM type recognition procedure) with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "0" (i.e. 5V only SIM).
The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 5V only SIM.
The SIM/ME interface is monitored... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.2.5 Test requirement | 1) Immediately after the ATR only the two command "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 3V only ME shall deactivate the SIM/ME interface immediately after receipt of the status information from the SIM (but not later than 5 s after the "STATUS/GET RESPONSE command) and reject the SIM (i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3 Reaction of 3V technology MEs on type recognition of 5V only SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.1 Definition | When a 3V technology ME detects a 5V only SIM during the SIM type recognition procedure, the ME shall switch to 5V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.2 Conformance requirement | 1) A 3V technology ME shall initially activate the SIM at 3V (i.e. the first activation of a GSM card session.
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR procedure and before issuing any other command. The procedure shall ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.3 Test purpose | 1) To verify that a 3V technology ME initially activates the SIM with 3V.
2) To verify that a 3V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 3V technology ME deactivates the SIM/ME interface immediately after the SIM type recognition procedure (in order to switch the supply ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 5V only SIM with nominal test conditions according to table 27.2‑1. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "0" (i.e. 5V only SIM).
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 5V only SIM.
The SIM/ME interface is monitored... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.3.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 3V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME before issuing further commands.
3) The 3V technology ME shall deactivate the SIM/ME interface immediately after recei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4 Reaction of 3V technology MEs on type recognition of 3V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.1 Definition | When a 3V technology ME detects a 3V technology SIM during the SIM type recognition procedure the ME may either switch to 5V operation or stay in 3V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.2 Conformance requirement | 1) A 3V technology ME shall initially activate the SIM with a 3V (i.e. the first activation of a GSM card session).
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. the procedure shall consi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.3 Test purpose | 1) To verify that a 3V technology ME initially activates the SIM with 3V.
2) To verify that a 3V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 3V technology ME deactivates the SIM/ME interface immediately after the recognition of a 3V technology SIM (in order to switch the sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bit 5 in byte 14 of the status information is set to "1" (i.e. 3V technology SIM.)
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.4.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is monitor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.27.1.5.4.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 3V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE: shall be sent by the ME.
3) The ME shall react in one of the following ways:
a) The ME deactivates the SIM/ME interface immediately after the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5 Reaction of 1,8V only MEs on SIM type recognition failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.1 Definition | When a 1,8V only ME detects a failure during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE".
2) If a 1,8V only ME cannot complete the SIM type rec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.3 Test purpose | 1) To verify that a 1,8V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 1,8V only ME deactivates the SIM/ME interface and rejects the SIM in case that the SIM does not respond to the "STATUS/GET RESPONSE" command. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM with nominal test conditions according to table 27.2‑3. All elementary files are coded as default.
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator does not respond to the "STATUS/GET RESPONSE" command.
The SIM/ME interface is monitored for at least 1 minute until the MS is swit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.5.5 Test requirement | 1) Immediately after the ATR only the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 1,8V only ME shall deactivate the SIM/ME interface within 5 s and reject the SIM (i.e. not activate the SIM/ME interface within the test procedure). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6 Reaction of 1,8V only MEs on type recognition of 3V SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.1 Definition | When a 1,8V only ME detects a 3V technology SIM during the SIM type recognition procedure, the ME shall reject the SIM in order to prevent any damage to the SIM.
. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.2 Conformance requirement | 1) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. The procedure shall consist of the two commands "SELECT GSM" and "STATUS/GET RESPONSE"
2) If a 1,8V only ME identifies a 3V technology SIM du... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.3 Test purpose | 1) To verify that a 1,8V only ME correctly performs the SIM type recognition procedure.
2) To verify that a 1,8V only ME deactivates the SIM/ME interface and rejects the SIM if a 3V technology SIM is applied. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM (to ensure that the ME can perform the SIM type recognition procedure) with nominal test conditions according to table 27.2‑3. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "01" (i.e. 3V tec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is mon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.6.5 Test requirement | 1) Immediately after the ATR only the two command "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME.
2) The 1,8V only ME shall deactivate the SIM/ME interface immediately after receipt of the status information from the SIM (but not later than 5 s after the "STATUS/GET RESPONSE command) and reject the SIM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7 Reaction of 1,8V technology MEs on type recognition of 3V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.1 Definition | When a 1,8V technology ME detects a 3V technology SIM during the SIM type recognition procedure, the ME shall switch to 3V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.2 Conformance requirement | 1) A 1,8V technology ME shall initially activate the SIM at 1,8V (i.e. the first activation of a GSM card session.
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR procedure and before issuing any other command. The procedure sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.3 Test purpose | 1) To verify that a 1,8V technology ME initially activates the SIM with 1,8V.
2) To verify that a 1,8V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 1,8V technology ME deactivates the SIM/ME interface immediately after the SIM type recognition procedure (in order to switch the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 3V technology SIM with nominal test conditions according to table 27.2‑2. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "01" (i.e. 3V technology SIM).
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of the commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 3V technology SIM.
The SIM/ME interface is mon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.7.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 1,8V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be sent by the ME before issuing further commands.
3) The 1,8V technology ME shall deactivate the SIM/ME interface immediately after r... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8 Reaction of 1,8V technology MEs on type recognition of 1,8V technology SIMs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.1 Definition | When a 1,8V technology ME detects a 1,8V technology SIM during the SIM type recognition procedure the ME may either switch to 3V operation or stay in 1,8V operation. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.2 Conformance requirement | 1) A 1,8V technology ME shall initially activate the SIM with a 1,8V (i.e. the first activation of a GSM card session).
2) The procedure for deriving the identification bit (SIM type recognition procedure) shall be performed by the ME immediately after the ATR and before issuing any other command. the procedure shall c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.3 Test purpose | 1) To verify that a 1,8V technology ME initially activates the SIM with 1,8V.
2) To verify that a 1,8V technology ME correctly performs the SIM type recognition procedure.
3) To verify that a 1,8V technology ME deactivates the SIM/ME interface immediately after the recognition of a 1,8V technology SIM (in order to swit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4.1 Initial condition | The ME is connected to a SIM Simulator simulating a 1,8V technology SIM with nominal test conditions according to table 27.2‑3. All elementary files are coded as default. Bits 6 and 5 in byte 14 of the status information are set to "11" (i.e. 1,8V technology SIM.)
The ME is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.4.2 Procedure | After sending the ATR the SIM simulator checks the presence of commands "SELECT GSM" and "STATUS/GET RESPONSE" as the first and only commands of the GSM card session.
The SIM simulator responds to the "STATUS/GET RESPONSE" command with a status information indicating a 1,8V technology SIM.
The SIM/ME interface is monit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.1.5.8.5 Test requirement | 1) The initial activation of the SIM/ME interface shall be performed with 1,8V supply voltage.
2) Immediately after the ATR the two commands "SELECT GSM" and "STATUS/GET RESPONSE: shall be sent by the ME.
3) The ME shall react in one of the following ways:
a) The ME deactivates the SIM/ME interface immediately after th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2 Electrical tests on each ME contact | The following tables give the electrical conditions that must be applied by the SIM simulator to all contacts during a test if not stated otherwise.
Table 27.2-1: Nominal test conditions on 5V SIM/ME interface
Contacts
Low level
High level
Max. capacitive load
C1 (Vcc)
---
I = 10 mA
C2 (RST)
I = ‑200 A
I = +20 A
30 p... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1 Electrical tests on contact C1 | C1 = Card power supply (Vcc). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1 Test 1 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1.1 Definition | When the mobile station is activated, the supply voltage on the SIM/ME interface shall remain in the specified range in order to ensure correct operation and to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1.2 Conformance requirement | a) The voltage on contact C1 of the SIM/ME interface shall be 5V ± 10 % for Icc up to 10 mA.
b) The voltage on contact C1 of the SIM/ME interface shall be 3V ± 10 % for Icc up to 6 mA.
c.1) The voltage on contact C1 of the SIM/ME interface shall be 5V ± 10 % for Icc up to 10 mA when the interface is in 5V operation mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1.3 Test purpose | To verify that the ME keeps the voltage on contact C1 of the SIM/ME interface within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1.4 Method of test | Initial condition
The ME is connected to a SIM Simulator.
The MS is activated.
The remaining contacts of the SIM/ME interface are in nominal test conditions (see 3GPP TS 11.10 subclause 27.17.2).
Test Procedure
The voltage of contact C1 (Vcc) of the SIM/ME interface is measured. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.1.5 Test requirement | The voltage on contact C1 of the SIM/ME interface shall be within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2 Test 2 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2.1 Definition | When the mobile station is activated, the supply voltage on the SIM/ME interface shall be able to counteract spikes in the current consumption of the SIM up to the limits given in the conformance requirement, ensuring that the supply voltage stays in the specified range. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2.2 Conformance requirement | a) The voltage on contact C1 of the SIM/ME interface shall be 5V ± 10 % for spikes in the current consumption with a maximum charge of 40 nAs with no more than 400 ns duration and an amplitude of at most 200 mA.
b) The voltage on contact C1 of the SIM/ME interface shall be 3V ± 10 % for spikes in the current consumptio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2.3 Test purpose | To verify that the ME keeps the voltage on contact C1 of the SIM/ME interface within the specified range for the conditions given in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2.4 Method of test | Initial condition
The ME is connected to a SIM Simulator.
The MS is activated.
The remaining contacts of the SIM/ME interface are held in nominal test condition (see 3GPP TS 11.10 subclause 27.17.2).
Procedure
To test the requirements a) and c-1), the voltage on contact C1 of the SIM/ME interface is monitored and the f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.1.2.5 Test requirement | The voltage on contact C1 of the SIM/ME interface shall be within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2 Electrical tests on contact C2 | C2 = Reset (RST). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.1 Definition | When the mobile station is activated, the voltage on contact C2 of the SIM/ME interface shall remain in the specified range in order to ensure correct operation and to prevent any damage to the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.2 Conformance requirement | a) The voltage on contact C2 (RST) of the SIM/ME interface shall be between ‑0,3V and +0,6V for a current of ‑200 A in low state and between 3,8V and Vcc + 0,3V for a current of +20 A in high state.
b) The voltage on contact C2 (RST) of the SIM/ME interface shall be between ‑0,3V and +0,7V for a current of ‑200 A in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.3 Test purpose | To verify that the ME keeps the voltage on contact C2 (RST) of the SIM/ME interface within the specified range, as given in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.4.1 Initial condition | The ME is connected to a SIM Simulator.
The MS is activated.
The remaining contacts of the SIM/ME interface are held in nominal test conditions (see 3GPP TS 11.10 subclause 27.17.2). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.4.2 Procedure | The voltage on contact C2 (RST) of the SIM/ME interface is measured. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.2.5 Test requirement | The voltage on contact C2 (RST) of the SIM/ME interface shall be within the range specified in the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3 Electrical tests on contact C3 | C3 = Clock (CLK). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.1 Definition | When the mobile station is activated, the voltage, the rise/fall time of the signal, the clock cycle ratio and the frequency on contact C3 of the SIM/ME interface shall remain in the specified range in order to ensure correct operation and to prevent any damage to the SIM.
. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.2 Conformance requirement | a.1) The voltage on contact C3 (CLK) of the SIM/ME interface shall be between ‑0,3V and +0,5V for a current of ‑200 A in low state and between 3,15V and Vcc +0,3V for a current of +20 A in high state.
a.2) The rise and the fall time of the clock signal shall not exceed 9 % of the clock period .
a.3) The cycle ratio o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.3 Test purpose | To verify that the ME keeps the voltage, the rise and fall time, the cycle ratio and the frequency on contact C3 (CLK) of the SIM/ME interface within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.4.1 Initial condition | The ME is connected to a SIM Simulator.
The MS is activated.
The remaining contacts of the SIM/ME interface are held in nominal test conditions (see 3GPP TS 11.10 subclause 27.17.2). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.4.2 Procedure | The voltage, the rise/fall time, the clock cycle ratio and the frequency on contact C3 (CLK) of the SIM/ME interface are measured. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.3.5 Test requirement | The voltage, the rise and fall time, the cycle ratio and the frequency on contact C3 (CLK) of the SIM/ME interface shall be within the ranges specified in the conformance requirements.
27.17.2.4 [Not used] |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5 Electrical tests on contact C7 | C7 = Input - output (I/O). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.1 Definition | When the mobile station is activated, the ME shall keep the voltage, the current and the rise/fall time of the signal on contact C7 of the SIM/ME interface within the specified range in order to ensure correct operation and to prevent any damage to the SIM.. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.2 Conformance requirement | a.1) ME receiving state A (low state):
With an imposed voltage of 0V the current flowing out of the ME shall not exceed 1 mA.
a.2) ME transmitting state A (low state):
The voltage shall be between ‑0,3V and 0,4V when a current of 1 mA flowing into the ME is applied.
a.3) ME transmitting or receiving state Z (high state... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.3 Test purpose | To verify that the ME keeps the voltage, the current and the rise and fall times of the signal on contact C7 (I/O) of the SIM/ME interface within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.4.1 Initial condition | The ME is connected to a SIM Simulator.
The MS is activated.
The remaining contacts of the SIM/ME interface are held in nominal test conditions (see 3GPP TS 11.10 subclause 27.17.2). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.4.2 Procedure | The voltage, the current and the rise/fall time on contact C7 (I/O) of the SIM/ME interface are measured. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.17.2.5.5 Test requirement | The voltage, the current and the rise and fall times of the signal on contact C7 (I/O) of the SIM/ME interface shall be within the ranges specified in the conformance requirements. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18 Fixed Dialling Number (FDN) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1 ME and SIM with FDN activated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1 EFADN invalidated and not readable or updatable | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.1 Definition | Fixed Dialling Number (FDN) is a service defined for the SIM. An activated FDN service results in call restrictions for the MS. The call restrictions are controlled by the ME. To ascertain the type of SIM and state of FDN the MS runs the FDN capability request procedure during SIM/ME initialization. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.2 Conformance requirement | 1. Recognizing the state of the SIM (FDN enabled) the MS shall perform the SIM initialization procedure as specified.
2. The MS allows call set-up to a directory number as stored in EFFDN.
3. The MS allows call set-up to a directory number as stored in EFFDN and extended by digits in the end.
4. The MS does not allow c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.3 Test purpose | 1. To verify that the ME as a result of the state of the SIM rehabilitates EFIMSI and EFLOCI during SIM/ME initialization procedure.
2. To verify that the ME allows call set-up to a FDN number.
3. To verify that the ME allows call set-up to a FDN number extended by some digits in the end.
4. To verify that the ME rejec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters
Attach/detach: disabled.
LAI-MCC: 246
LAI-MNC 81 or 813 (see Note 0)
LAI-LAC: 0001
LAI (MCC/MNC/LAC): 246/81/0001 or 246/813/0001 (see Note 0).
Access control: unrestricted.
The default FDN-SIM with FDN service enabled and EFADN invalidated and neither... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.4.2 Procedure | a) The MS is powered on and PIN1 is entered.
b) Using the MMI a call set-up to the fixed dialling number 1 is attempted.
c) Using the MMI a call set-up to the fixed dialling number 2 extended by "123" in the end is attempted.
d) Using the MMI a call set-up to a number which is equal to the fixed dialling number 3 witho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.1.5 Test requirement | 1) After step a) the MS is registered and in idle state.
2) After steps b) and c) the MS shall allow call set-up and send the requested number across the air interface.
3) After steps d) and e) the MS shall prevent call set-up.
4) After step f) the MS shall allow emergency call set-up and send the requested number acro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.18.1.2 EFADN invalidated but readable and updatable |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.