hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.2.1 Definition | -29.2.2.2 Conformance requirement
An MS supporting data services shall decode and filter channel control information received over the Um-interface.
1. 3GPP TS 04.21, clause 7;
2. 3GPP TS 07.01, subclause 8.2.2;
3. 3GPP TS 07.02, subclause 3.2.1 (for asynchronous bearer services only);
4. 3GPP TS 07.03, subclauses 4.2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.2.3 Test purpose | The purpose of this test is to verify the correct decoding and filtering of channel control information from the 3GPP TS 04.21 frames to the V.24/X.21 interface circuits. The tests apply after synchronization has been completed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.2.4 Method of test | The Test shall be carried out for all user data rates supported by the MS (see below) and the circuits CT106 (V.24) (interface circuit bit X) and CT109 (V.24) (interface circuit bit SB) and I (X.21) (S-bits). The test shall be carried out only for those frame formats and circuits which are supported by the MS. The test... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.2.5 Test requirements | 1) After step a) the interface circuit at the R-interface shall be OFF.
2) During step b) the interface circuit at the R-interface shall not change.
3) During step c) the interface circuit at the R-interface shall change to ON and then again to OFF.
4) After step d) the interface circuit at the R-interface shall be ON.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.2.6 BCIE | The following combinations shall be considered (ref. 3GPP TS 07.01, annex 2):
a) User Rate = 9,6 kbit/s;
b) User Rate = 4,8 kbit/s;
c) User Rate = 2,4 kbit/s;
d) User Rate = 1,2 kbit/s;
e) User Rate = 1 200/75 bit/s (only with asynchronous Bearer Services);
f) User Rate = 300 bit/s (only with asynchronous Bearer Servic... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3 Correct Terminal Compatibility Decision | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.1 Negotiation of Radio Channel Requirement (RCR) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.1.1 Test purpose | To verify that the MS ignores the RCR field in a mobile terminating setup and negotiates according to its capabilities and to the service requested. A Dual Rate support MS shall accept the channel rate chosen be the network in the ASSIGNMENT COMMAND message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.1.2 Initial conditions | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
-
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.1.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and with the RCR field set to "01".
b) The SS sends a ASSIGNMENT COMMAND message with a channel type set to "Full Rate" unless the CALL CONFIRM message indicates "dual rate mobile station/full rate preferred". In that cas... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.1.4 Test requirements | 1) After step a), the MS shall send a CALL CONFIRM message. If present, the BC-IE shall be coded according to 3GPP TS 07.01. If any other parameters than those listed below have different values than those of the BC-IE included in the SETUP, then the test shall be failed:
- Number of stop bits, number of data bits, par... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.2 Negotiation of Connection Element (CE) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.2.1 Test purpose | To verify that the MS accepts a CE equal to "Both, Transparent Preferred" or "Both Non Transparent Preferred" and indicates its choice in the CALL CONFIRM message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.2.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
•
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.2.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and with the CE field set to "Both Transparent Preferred". The RCR parameter shall be set to "Full Rate". The UIL2P is not included (i.e. octet 7 is absent). The NIRR is set to "no meaning" (i.e. 0). The IR is set to "16 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.2.4 Test requirements | After step a), the MS shall send a CALL CONFIRM message. The BC-IE shall be present and shall be coded according to 3GPP TS 07.01 and shall correspond to a Bearer Service or Teleservice supported by the MS. The CE shall be set to either "Transparent" or "Non Transparent" If any other parameters than those listed bellow... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.3 Negotiation of Number of Stop Bits, Number of Data bits, and Parity | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.3.1 Test purpose | To verify that the MS accepts any value for the parameters Number of Stop Bits, Number of Data bits, and Parity in a mobile terminating Setup and negotiates according to its capabilities and to the service requested. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.3.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
-
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.3.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and corresponding to an asynchronous Bearer Service, and with the Number of Stop Bits (NSB) field set to "1 bit", the Number of Data Bits (NDB) field set to "8 bits", and the Parity field set to "none".
b) The call is rel... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.3.4 Test requirements | After steps a) and b), the MS shall send a CALL CONFIRMED message. If present, the BC-IE shall be coded according to 3GPP TS 07.01 and shall correspond to a Bearer Service supported by the MS. If any other parameters than those listed bellow have different values than those of the BC-IE included in the SETUP, then the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.4 Negotiation of Modem Type | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.4.1 Test purpose | To verify that the MS accepts the value "autobauding type 1" for the parameter Modem Type in a mobile terminating Setup and negotiates according to its capabilities and to the service requested.
NOTE: It is not clear if the MS should also accept any possible value for the Modem Type field. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.4.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
-
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.4.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and corresponding to a non transparent Bearer Service (the Connection Element field is coded "Non transparent"), and with the Modem Type field set to "autobauding type 1".
b) The call is released and step a) is repeated w... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.4.4 Test requirements | After steps a) and b), the MS shall send a CALL CONFIRMED message. If present, the BC-IE shall be coded according to 3GPP TS 07.01 and shall correspond to a Bearer Service or Teleservice supported by the MS. If any other parameters than those listed bellow have different values than those of the BC-IE included in the S... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.5 Negotiation of Intermediate Rate | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.5.1 Test purpose | To verify that the MS responds correctly to a request for a negotiation of the Intermediate Rate parameter in a mobile terminating Setup and negotiates according to its capabilities and to the service requested.
NOTE: The MS may support these services with a 6 Kbit/s or (non exclusive) 12 Kbit/s radio interface rate.
2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.5.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and corresponding to a non transparent Bearer Service (the Connection Element field is coded "Non transparent") with the user rate lower to or equal 4,8 kbit/s, and with the NIRR field set to "No meaning". The RCR field i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.5.4 Test requirements | 1) After steps a), b) and c), the MS shall send a CALL CONFIRMED message. If present, the BC-IE shall be coded according to 3GPP TS 07.01 and shall correspond to a Bearer Service or Teleservice supported by the MS. If any other parameters than those listed bellow have different values than those of the BC-IE included i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.6 Negotiation of User Information Layer 2 Protocol | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.6.1 Test purpose | To verify that the MS accepts any value (including the absence of) the UIL2P parameter in a mobile terminating Setup and negotiates according to its capabilities and to the service requested. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.6.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
-
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.6.3 Test method | a) The SS transmits a SETUP message containing a BC-IE among those declared as supported by the MS and corresponding to a non transparent Bearer Service (the Connection Element field is coded "Non transparent") and with no UIL2P parameter (i.e. octet 7 of the BC IE is absent).
b) The call is released and step a) is rep... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.6.4 Test requirements | 1) After steps a), b) and c), the MS shall send a CALL CONFIRMED message. If present, the BC-IE shall be coded according to 3GPP TS 07.01 and shall correspond to a Bearer Service or Teleservice supported by the MS. If any other parameters than those listed bellow have different values than those of the BC-IE included i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.7 Negotiation between TS 61 and TS 62: Mobile Originated call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.7.1 Test purpose | To verify that the MS accepts a negotiation from TS 61 to TS 62. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.7.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully set up a call for TS 61.
Specific PICS statements:
-
PIXIT statements:
- Way to set up the call
- Features which must be activated by MMI before an outgoing call can be set up. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.7.3 Test method | a) The MS is made to set up a call for TS 61. If the MS supports it, the first phase of the call is speech.
b) The SS responds to the SETUP message with a CALL PROCEEDING message containing a BC-IE coded according to 3GPP TS 07.01 and corresponding to TS 62.
c) The SS sends an ALERTING message followed by a CONNECT mes... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.7.4 Test requirements | 1) After step b), the MS shall accept the call (i.e. it shall not reject the call with a DISCONNECT message).
2) After step c), the MS shall answer with a CONNECT ACKNOWLEDGE message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.8 Negotiation between TS 61 and TS 62: Mobile Terminated call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.8.1 Test purpose | To verify that an MS that does not support TS 61 accepts a Mobile Terminated call setup request for TS 61 and negotiates the demand to TS 62. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.8.2 Initial condition | For an MS with an external interface, the interface shall be setup in such a way that the MS is able to successfully receive the call for the service in question.
Specific PICS statements:
•
PIXIT statements:
- Way to receive the call
- Features which must be activated by MMI before an incoming call can be accepted. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.8.3 Test method | a) The SS transmits a SETUP message containing two BC-IEs: the first BC shall indicate speech, the second BC shall indicate fax group 3.
b) The call is released, and the SS transmits a SETUP message containing two BC-IEs: the first BC shall indicate fax group 3, the second BC shall indicate speech. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.3.8.4 Test requirements | After steps a) and b), the MS shall send a CALL CONFIRMED message with one and only one BC-IE. The BC-IE shall be coded according to 3GPP TS 07.01 and shall correspond to TS 62. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4 Data Rate Adaptation for Synchronous Transparent Bearer Capabilities | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4.1 Definition | -29.2.4.2 Conformance requirement
An MS supporting synchronous transparent bearer capabilities shall perform data rate adaptation and support the frames at the Um-interface according to the following specifications:
1. 3GPP TS 04.21, clauses 5 and 7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4.3 Test purpose | The purpose of these tests is to verify:
- that the format and the data bits of the 3GPP TS 04.21 frames sent by the MS are consistent with the data input and data rate at the R-interface; and
- that the data bits output by the MS at the R-interface are consistent with the received 3GPP TS 04.21 frames. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4.4 Method of test | The Test shall be carried out for all possible user data rates which are supported by the MS (see below). In case of an MT2 configuration, the interface circuits CT105 and CT108 shall be set to the ON condition from the start.
Procedure:
a) A data call shall be set up between the SS and the MS with a BCIE (see below) s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) Only MT2 configuration: the user data stream input to the R-interface shall ma... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.4.6 BCIE | The following combinations shall be considered (ref. 3GPP TS 07.01, annex 2):
a) User Rate = 9,6 kbit/s;
b) User Rate = 4,8 kbit/s;
c) User Rate = 2,4 kbit/s;
d) User Rate = 1,2 kbit/s.
The remaining parameters of the BCIE and the channel type (FR/HR) shall be set to a value supported by the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.5 Network Independent Clocking | For further study. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6 Asynchronous Transparent Bearer Capabilities | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1 Data Rate Adaptation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.1 Definition | -29.2.6.1.2 Conformance requirement
An MS supporting asynchronous transparent bearer capabilities shall perform data rate adaptation and support the frames at the Um-interface according to the following specifications:
1. 3GPP TS 04.21, subclauses 4.1 and 4.4, clauses 5 and 7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.3 Test purpose | The purpose of these tests is to verify the conversion between an asynchronous data stream at the R-interface and the 3GPP TS 04.21 frames at the Um-interface. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.4 Method of test | The Test shall be carried out for all possible user data rates which are supported by the MS in asynchronous mode (see below).
Procedure:
a) A data call shall be set up between the SS and the MS with a BCIE (see below) supported by the MS. The next step shall be entered immediately after TCH synchronization has been co... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) MT2 configuration only: the user data stream input to the R-interface shall ma... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.6 Generation of the asynchronous pseudo random characters | Downlink direction:
The 3GPP TS 04.21 frames shall contain a bit stream which consists of repeating:
- a character which is generated pseudo randomly every time;
- n stop bits, where n is drawn pseudo randomly from the interval 1..15 every time.
Uplink direction:
The data stream at the R-interface consists of repeating... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.1.7 BCIE | Same as subclause 29.2.3.
The Number of Data Bits per character (excl. parity) shall be 8. No parity bit shall be used. The Number of Stop Bits shall be 1. If the MS does not support these values different ones shall be chosen.
The remaining parameters of the BCIE shall and the channel type (FR/HR) be set to a value su... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2 Passage of the Break Signal | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2.1 Definition | -29.2.6.2.2 Conformance requirement
An MS supporting asynchronous transparent bearer capabilities shall perform passage of the break signal in uplink and downlink direction according to:
1. 3GPP TS 04.21, subclauses 4.1, 4.2 and 4.4, clauses 5 and 7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2.3 Test purpose | The purpose of these tests is to verify the ability of the MS to transfer a Break Signal to the R-interface and vice versa. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2.4 Method of test | The Test shall be carried out for all possible user data rates which are supported by the MS in asynchronous mode (see below).
Procedure:
a) A data call shall be set up between the SS and the MS with a BCIE (see below) supported by the MS. The next step shall be entered immediately after TCH synchronization has been co... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) The user data stream sent over the Um-interface by the SS shall match characte... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.2.6 BCIE | Same as subclause 29.2.2.6. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3 Overspeed/Underspeed Handling (Local Terminal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3.1 Definition | -29.2.6.3.2 Conformance requirement
An MS supporting asynchronous transparent bearer capabilities shall handle overspeed and underspeed of the local terminal according to:
1. 3GPP TS 04.21, subclauses 4.1, 4.3 and 4.4, clauses 5 and 7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3.3 Test purpose | The purpose of these tests is to verify the ability of the MS to deal with plesiosynchronous bit clocks in the MS and the TE in case of asynchronous Bearer Capabilities. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3.4 Method of test | The Test shall be carried out for all possible user data rates supported by the MS in asynchronous mode (see below).
Procedure:
a) A data call shall be set up between the SS and the MS with a BCIE (see below) supported by the MS. The next step shall be entered immediately after CT107 has been set to on by the MS.
b) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) The user data stream input to the R-interface shall match character by charact... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.3.6 BCIE | Same as subclause 29.2.2.6.
The Number of Data Bits per character (excl. parity) shall be 8. No parity bit shall be used. The Number of Stop Bits shall be 1. If the MS does not support these values different ones shall be chosen.
The remaining parameters of the BCIE and the channel type (FR/HR) shall be set to a value ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4 Overspeed/Underspeed Handling (Remote Terminal) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4.1 Definition | -29.2.6.4.2 Conformance requirement
An MS supporting asynchronous transparent bearer capabilities shall handle overspeed and underspeed of the remote terminal (which shows in the structure of the 3GPP TS 04.21 frames received over the Um-interface) according to:
1. 3GPP TS 04.21, subclauses 4.1, 4.3 and 4.4, clauses 5 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4.3 Test purpose | The purpose of these tests is to verify the ability of the MS to deal with plesiosynchronous bit clocks in the MS and the remote Terminal in case of asynchronous Bearer Capabilities.
The case of underspeed is covered by subclause 29.6.1. The case of overspeed shall be tested as follows. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4.4 Method of test | The Test shall be carried out for all possible user data rates supported by the MS in asynchronous mode (see below).
Procedure:
a) A data call shall be set up between the SS and the MS with a BCIE (see below) supported by the MS. The next step shall be entered immediately after CT107 has been set to on by the MS.
b) Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) The user data stream sent by the SS over the Um-interface shall match characte... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.6.4.6 BCIE | Same as subclause 29.2.6.3.6. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7 Interchange circuit mapping for transparent bearer capabilities | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.1 Definition | This test cannot be applied fully to MSs which support e.g.:
- CT108/2 for releasing the call (e.g. support of ITU-T Recommendation V.25bis) and/or
- similar use of the circuit C for ITU-T Recommendation X.21.
Therefore the test shall be applied only for those interchange circuits which do not influence Layer 3 signall... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.2 Conformance requirement | 1) An MS supporting transparent bearer capabilities with a V-series R-interface shall map the interchange circuits CT105 and CT108/2 to the 3GPP TS 04.21 frames sent over the Um-interface according to:
1.1 3GPP TS 04.21, subclauses 4.1 and 4.4, clauses 5 and 7.
1.2 3GPP TS 07.02, subclause 3.2.1.
2) An MS supporting tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.3 Test purpose | The purpose of these tests is to verify the ability of the MS to correctly convey changes of the interface circuits at the R‑interface to the 3GPP TS 04.21 frame sent over the Um-interface in case of Transparent Bearer Capabilities. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.4 Method of test | Specific PICS statements:
-
PIXIT statements:
- Interchange Circuits which influence Layer 3 signalling
The Test shall be carried out for all user data rates supported by the MS (see below) and the circuits CT105 and CT108/2 (ITU-T Recommendation V.24) and C (ITU-T Recommendation X.21). The test shall be carried out on... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.5 Test requirements | 1) During the test no 3GPP TS 04.21 frame with incorrect format (i.e. format not compliant to 3GPP TS 04.21 (see conformance requirement) or not corresponding to the user data rate currently under test) shall have been received by the SS.
2) The change of the interchange circuit signal level shall be indicated in the 3... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.2.7.6 BCIE | Same as subclause 29.2.2.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3 Testing of non transparent data services (RLP tests) | SS sends NULL (C/R=0, P/F=0) frames when it has nothing else to send in ADM mode.
SS does not use DTX if not explicitly indicated in the test and sends supervisory RR (C/R=0, P/F=0) frames when it has nothing else to send in ABM mode. N(R) is equal to N(R) of the previous frame. For the first frame N(R)=0.
The informat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1 Initialization | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.1 Normal initialization done by the MS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.1.1 Test purpose | To test the normal establishment of multiple frame operation between the SS and the MS.
This test is performed twice for testing MO and MT data calls: |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.1.2 Method of test | Initial Conditions
System Simulator:
The SS is configured to use default RLP parameters.
Mobile Station:
The MS is configured to use default RLP parameters.
MO data call:
The MS is made to establish a MO non transparent data call, so that the initial conditions are that the MS is in call state U10 ("Call Active") after... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.1.3 Test requirements | The frames from the MS shall be:
1: One SABM frame containing:
C=1, P=1.
The SABM shall not be repeated.
4: One S or I+S frame with N(R)=1 acknowledging the I+S frame. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2 Initialization failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.1 Loss of UA frame | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.1.1 Test purpose | To test the MS response to the loss of an UA frame during initialization. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.1.2 Method of test | Initial Conditions
System Simulator:
The SS is configured to use default RLP parameters.
Mobile Station:
The MS is configured to use default RLP parameters. The MS is made to establish a MO non transparent data call so that the initial conditions are that the MS is in call state U10 ("Call Active") after having sent a ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.1.3 Test requirements | The frames from the MS shall be:
1, 2: One SABM frame containing:
C=1, P=1.
The second SABM frame shall follow the first SABM frame after time-out of timer T1.
5: One S or I+S frame with N(R)=1 acknowledging the I+S frame. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.2 Total loss of UA frame | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.2.1 Test purpose | To test the MS response to a total loss of UA frame during initialization. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.2.2 Method of test | Initial Conditions
System Simulator:
The SS is configured to use default RLP parameters.
Mobile Station:
The MS is configured to use default RLP parameters.
The MS is made to establish a MO non transparent data call so that the initial conditions are that the MS is in call state U10 ("Call Active") after having sent a ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 29.3.1.2.2.3 Test requirements: | The frames from the MS shall be:
1, .... N2: One SABM frame containing:
C=1, P=1.
An SABM frame follows the previous one after time-out of timer T1. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.