hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.1.6.2 Test Purpose | To verify that the mobile station returns a PACKET CELL CHANGE FAILURE message, if the ordered frequency cannot be used.
Reference
3GPP TS 04.60, subclause 8.4.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.1.6.3 Method of test | System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
PDP context established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in Transfer mode.
Test procedure
MS is brought into uplink packet transfer mode. SS sends the PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2 Cell change order procedure / Downlink transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.1 Cell change order procedure / Downlink transfer / Normal case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.1.1 Conformance requirement | The cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message to the mobile station on the PCCCH or PACCH. Upon receipt of the PACKET CELL CHANGE ORDER message the mobile station shall start timer T3174.
When a cell reselection is made controlled by the network, the mobile station shall act u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.1.2 Test Purpose | To verify that when NC2 is commanded, the MS sends PACKET MEASUREMENT REPORT messages, in which both the serving and non-serving cells are reported.
To verify that the cell change order procedure is started when the MS receives a PACKET CELL CHANGE ORDER message.
To verify that the MS switches to the new cell.
To verif... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.1.3 Method of test | Initial conditions
System Simulator:
2 cells (cell A, cell B), activated at power-on, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
PDP context established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in Transfer mode.
Test procedure
MS is brought ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.2 Cell change order procedure / Downlink transfer / Failure cases / REJECT from the new cell | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.2.1 Conformance requirement | If a PACKET ACCESS REJECT message is received from the new cell, the mobile station shall start timer T3176, return to the old cell and send a PACKET CELL CHANGE FAILURE message to the network.
If the mobile station was in downlink packet transfer mode before the cell change, the mobile station shall initiate a random ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.2.2 Test Purpose | To verify that the mobile station sends a PACKET CELL CHANGE FAILURE message to the network in the old cell, if a IMMEDIATE ASSIGNMENT REJECT message is received from the new cell.
Reference
3GPP TS 04.60, subclause 8.4.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.2.3 Method of test | Initial conditions
System Simulator:
2 cells (cell A, cell B), activated at power-on GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached. Ready Timer is deactivated.
PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in idle mode.
Test... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.3 Cell change order procedure / Downlink transfer / Failure cases / Frequency not implemented | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.3.1 Conformance requirement | If the network message instructs the mobile station to use a frequency that it is not capable of using, the mobile station shall send a PACKET CELL CHANGE FAILURE message and remain on the current PDCH(s). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.3.2 Test Purpose | To verify that the mobile station returns a PACKET CELL CHANGE FAILURE message if it is not capable of using the ordered frequency.
Reference
3GPP TS 04.60, subclause 8.4.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.2.3.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
PDP context established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in idle mode.
Test procedure
MS is brought into downlink packet transfer mode. SS sends ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3 Cell change order procedure / Simultaneous uplink and downlink transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.1 Cell change order procedure / Simultaneous uplink and downlink transfer / Normal case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.1.1 Conformance requirement | The cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message to the mobile station on the PCCCH or PACCH. Upon receipt of the PACKET CELL CHANGE ORDER message the mobile station shall start timer T3174.
When a cell reselection is made controlled by the network, the mobile station shall act u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.1.2 Test Purpose | To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message, the MS shall abort any TBF in progress and stop transmitting.
To verify that the MS shall switch to the new cell.
To verify that the MS shall act upon the IMMEDIATE_REL value.
Reference
3GPP TS 04.60, subclause... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.1.3 Method of test | Initial conditions
System Simulator:
2 cells (cell A, cell B), activated at power-on, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in simultaneous uplink and downlink packet tr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.4 Packet Measurement order procedure / Downlink transfer / Normal case/ Routing Area Update/ NMO II | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.4.1 Conformance requirement | The cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message to the mobile station on the PCCCH or PACCH. Upon receipt of the PACKET CELL CHANGE ORDER message the mobile station shall start timer T3174.
When a cell reselection is made controlled by the network, the mobile station shall act u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.4.2 Test Purpose | To test the behaviour of the MS when the network triggers a Packet Cell Change Order to a cell belonging to another routing area, whereas the network mode of operation II is active, i.e.:
- To verify that the cell change order procedure is started when the MS receives a PACKET CELL CHANGE ORDER message.
- To verify tha... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.4.3 Method of test | Initial conditions
System simulator:
2 cells, GPRS supported, Carrier 1 is active, at –60dBm. Carrier 2 is on, at low level –70dBm (in order to prevent sync reading suspension due to unsuccessful synchronization attempts). PBCCH is not present on Cell A (Carrier 1), and not present on Cell B (Carrier 2). NETWORK_CONTRO... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.5 Packet Measurement order procedure / Downlink transfer / Normal case/ Routing Area Update/ NMO I | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.5.1 Conformance requirement | The cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message to the mobile station on the PCCCH or PACCH. Upon receipt of the PACKET CELL CHANGE ORDER message the mobile station shall start timer T3174.
When a cell reselection is made controlled by the network, the mobile station shall act u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.5.2 Test Purpose | To test the behaviour of the MS when the network triggers a Packet Cell Change Order to a cell belonging to another routing area, whereas the network mode of operation 1 is active, i.e.:
To verify that the cell change order procedure is started when the MS receives a PACKET CELL CHANGE ORDER message.
To verify that the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.5.3 Method of test | Initial conditions
System simulator:
2 cells, GPRS supported, Carrier 1 is active, at –60dBm. Carrier 2 is on, at low level –70dBm (in order to prevent sync reading suspension due to unsuccessful synchronization attempts). NETWORK_CONTROL_ORDER is set to NC0, and Network Mode of Operation is set to NMO I, on both Carri... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.6 MT CS establishment whilst in NC2 with a downlink TBF established | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.6.1 Conformance requirements | The behaviour of the mobile station is controlled by the NETWORK_CONTROL_ORDER parameter in a PACKET MEASUREMENT ORDER message. The reporting periods are indicated in the NC_REPORTING_PERIOD_T field of the PACKET MEASUREMENT ORDER message. The mobile station shall apply to the timer T3158 the NC_REPORTING_PERIOD_T when... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.6.2 Test purpose | To verify that the MS sends the measurement report of the NC measurements according to the indicated reporting periods, when the T3158 expires. To verify that the MS reacts to CS paging on the PACCH, whilst the MS was in packet transfer mode and NC2, by releasing the downlink TBF and then establishing an RR connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.6.3 Method of test | Initial Conditions
System Simulator:
2 cells, GPRS supported, NMO I activated, CTRL_ACK_TYPE=0 in SI13.
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated and PDP context 1 activated.
Specific PICS Statements
- GPRS Release Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.7 MT CS establishment whilst in NC2 with a uplink TBF established | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.7.1 Conformance requirements | The behaviour of the mobile station is controlled by the NETWORK_CONTROL_ORDER parameter in a PACKET MEASUREMENT ORDER message. The reporting periods are indicated in the NC_REPORTING_PERIOD_T field of the PACKET MEASUREMENT ORDER message. The mobile station shall apply to the timer T3158 the NC_REPORTING_PERIOD_T when... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.7.2 Test purpose | To verify that the MS sends packet measurement reports of the NC measurements according to the indicated reporting periods when T3158 expires. To verify that the MS reacts to CS paging on the PACCH, whilst the MS was in packet transfer mode and NC2, by releasing the uplink TBF and then establishing the RR connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.2.3.7.3 Method of test | Initial Conditions
System Simulator:
2 cells, GPRS supported, NMO I activated.
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated and PDP context 2activated.
NOTE: carrier 2 is activated in order to prevent synchronisation reading suspension due to unsuccessful synchronization attempts.
Specif... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3 Macros and Default Message contents | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.1 Macros | In order to simplify the process of writing and coding test cases, macros are referenced in the expected signalling tables. These macros provide all additional signalling needed to complete the particular test but are not relevant to its purpose. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.1.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.1.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.2 Default Messages | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.2.1 PACKET CELL CHANGE ORDER message | MESSAGE_TYPE
0000 01
PAGE_MODE
00 Normal Paging
Referenced Address
-
10 (address is TLLI)
- TLLI
same as the value received from MS
IMMEDIATE_REL
1 (Immediate release of the on-going TBF.)
ARFCN
For GSM 900: 00 0001 0100 (ARFCN 20)
For DCS 1 800 and PCS 1 900: 10 0100 1110 (ARFCN 590)
For GSM 700, T-GSM 810: 01 1100 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.2.2 PACKET CELL CHANGE FAILURE message | MESSAGE_TYPE
0000 00
TLLI
same as the value received from MS
ARFCN
For GSM 900: 00 0001 0100 (ARFCN 20)
For DCS 1 800 and PCS 1 900: 10 0100 1110 (ARFCN 590)
For GSM 700, T-GSM 810: 01 1100 1001 (ARFCN 457)
For GSM 850: 00 1001 0011 (ARFCN 147)
BSIC
For GSM 700, T-GSM 810, GSM 850 and GSM 900: 001101
For DCS 1 800 and ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.3.2.3 PACKET MEASUREMENT ORDER message | MESSAGE_TYPE
0000 11
PAGE_MODE
00 Normal Paging
TLLI
10 (address is TLLI)
-
Same as the value received from MS
PMO_INDEX
0 0 0 first message
PMO_COUNT
0 0 0 one message expected
{ 0 | 1 < NC Measurement Parameters }
1 NC Measurement Parameters available
NC Measurement Parameters
NETWORK_CONTROL_ORDER
0 1 NC1
{ 0 | ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4 Cell Change Order Procedures without PBCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1 Network Controlled Cell Reselection – Packet Measurement Order Procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1.1 Conformance requirement | A cell re-selection command may be sent from the network to an MS. When the MS receives the command, it shall immediately re-select the cell according to the included cell description and change the network control mode according to the command.
Reference:
3GPP TS 04.60 subclause 8.4.0.
3GPP TS 05.08 subclause 10.1.4.2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1.2 Test purpose | To verify that when the Network initiates the Packet Measurement Order Procedure, the MS correctly interprets the Packet Measurement Order Message, changes the network control mode and acts accordingly. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1.3 Method of test | Initial conditions
Parameter
Carrier1
Carrier2
Carrier3
RF Signal Level (dBm)
-70
-80
-50
GPRS_RXLEV_ACCE SS_MIN
-100
-100
-100
NETWORK_CONTRO L_ORDER
NC2
NC2
NC2
C1
30
20
50
C2
30
20
50
System simulator:
3 cells, GPRS supported, PBCCH not present (Carrier 1 & 2 is active. Carrier 3 is off).
Mobile Station:
MS is GPRS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2 Network Controlled Cell Reselection/validity of reselection parameters/MS enters standby state | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2.1 Conformance requirement | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to MS., th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2.2 Test purpose | To verify that the measurement reporting parameters are valid till the MS enters the standby state.
42.4.4.2.3 Method of test
Initial conditions
Parameter
Carrier1
Carrier2
RF Signal Level (dBm)
-80
-70
GPRS_RXLEV_ACCE SS_MIN
-100
-100
NETWORK_CONTRO L_ORDER
NC0
NC2
C1
20
30
C32
20
30
System simulator:
2 cells (cell A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3 Network Control measurement reporting / Idle mode / Returning to Broadcast parameters | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.1 Conformance requirement | The procedure for NC measurement report sending shall be initiated by the mobile station at the expiry of the NC measurement report interval timer T3158. At expiry of the timer T3158 the mobile station shall restart the timer T3158, perform the measurements and send the PACKET MEASUREMENT REPORT message containing the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.2 Test Purpose | To verify that individual parameters are valid only until the MS goes to Stand-by State. MS returns to broadcast parameters once it enters the Stand-by State and uses the broadcast parameters if it again goes to ready state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is GPRS attached with a P-TMSI allocated, SPLIT PG CYCLE negotiated
PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS assigns a single block downlink TBF to MS and sends PACKET MEASUREMENT ORDER chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.4 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5 Network Control measurement reporting / Idle mode / Reselection due to RA failure | 42.4.4.5.1 Conformance Requirement
Having made M + 1 attempts to send a PACKET CHANNEL REQUEST (respectively EGPRS PACKET CHANNEL REQUEST) message, the mobile station shall stop timer T3186 and start timer T3170. At expiry of timer T3170, the packet access procedure shall be aborted, a random access failure shall be in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5.2 Test Purpose | To verify that while in NC2, MS performs autonomous cell reselection when the reselection is triggered by the random access failure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5.3 Method of test | Initial conditions
System Simulator:
2 cell, GPRS supported.
Parameter
Carrier1
Carrier2
RF Signal Level (dBm)
-60
-70
NETWORK_CONTROL_ORDER
NC2
NC2
NC_REPORTING_PERIOD_I
Default
Default
Mobile Station:
MS is GPRS attached with a P-TMSI allocated, SPLIT PG CYCLE negotiated. Ready timer is set to 5 min.
PDP context 2 es... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5 Network Assisted Cell Change | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1 Network Assisted Cell Change / Expiry of T3206 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.1 Conformance requirements | [3GPP TS 44.060, 8.1.3]
If CCN is enabled (see subclause 5.5.1.1a, 3GPP TS 44.160 subclause 5.4.1.3), the mobile station shall behave as in network control mode NC0 or NC1 up to the point when a new cell has been chosen. It shall then check the CCN_SUPPORTED parameter, if available, that was last received for that cell... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.2 Test purpose | To verify that the MS leaves the CCN mode and continues cell reselection in NC0 mode when T3206 expires. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2 Network Assisted Cell Change / No Packet Neighbouring Cell Data and Packet Cell Change Continue | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.1 Conformance requirements | [3GPP TS 44.060, 8.1.1]
The mobile station shall transmit RLC/MAC blocks with the following priority:
• RLC/MAC control blocks containing a Packet Cell Change Notification message;
• Other RLC/MAC control blocks, except Packet Uplink Dummy Control Blocks;
• RLC data blocks;
• RLC/MAC control blocks containing Packet Up... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.2 Test purpose | 1) To verify that MS sends a PACKET CELL CHANGE NOTIFICATION when it enters CCN mode.
2) To verify that MS leaves CCN mode and continues cell reselection in NC0 mode when a PACKET CELL CHANGE CONTINUE is received when no PACKET NEIGHBOUR CELL DATA has been received. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4 Network Assisted Cell Change / Packet Neighbour Cell Data and Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.1 Conformance requirements | [3GPP TS 44.060, 5.5.1.4.3]
A mobile station supporting the Network Assisted Cell Change procedures shall implement the request for acquisition of system information (see clause 5.5.1.1a).
The PACKET PSI STATUS (respectively PACKET SI STATUS) message shall indicate the present status of PSI (respectively SI) messages s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.2 Test purpose | 1. To verify that the MS applies CCN when CCN is indicated in SI13 of the serving cell by sending a PACKET CELL CHANGE NOFITICATION when deciding to make a cell reselection.
2. To verify that MS leaves CCN mode when it receives a PACKET CELL CHANGE ORDER and follows the procedures as specified in the PACKET CELL CHANGE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.3 Method of test | Initial conditions
System Simulator:
3 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: The indication of Cell C is removed in SI2. RLA_C = -50 dBm
Cell B: Supports PACKET SI STATUS. No System Information is broadcast on the BCCH, except SI3. This is only made to m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5 Network Assisted Cell Change / Expiry of T3208 and T3210 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.2 Conformance requirements | [3GPP TS 44.060, 8.8.3]
After receiving a PACKET CELL CHANGE NOTIFICATION message from the mobile station the network can behave in different ways as described below.
5) No network response
When timer T3210 expires, the mobile station shall retransmit once the PACKET CELL CHANGE NOTIFICATION message at the first possib... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.2 Test purpose | 1. To verify that the MS retransmits the PACKET CELL CHANGE NOTIFICATION when T3210 expires 300 ms after no reception of any PACKET NEIGHBOUR CELL DATA, PACKET CELL CHANGE CONTINUE, PACKET MEASURMENT ORDER or PACKET CELL CHANGE ORDER.
2. To verify that MS leaves CCN mode when T3208 expires and continues cell reselectio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and PDP context 2 established.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6 Network Assisted Cell Change / Entering packet idle mode | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.1 Conformance requirements | [3GPP TS 44.060, 8.8.3]
The CCN mode is only valid in Packet Transfer Mode. If the mobile station is in CCN mode when entering packet idle mode, the mobile station shall stop the timers T3206 and T3208, stop timer T3210 if still running, leave CCN mode and continue the cell reselection procedure according to the NC0/NC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.2 Test purpose | To verify that the MS continues according to the normal packet idle mode cell reselection procedures when leaving CCN mode and entering packet idle mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
T3192 = 0 ms
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and PDP context 2 established.
C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7 Network Assisted Cell Change / CCN not supported towards target cell | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.1 Conformance requirements | The SI2quater message may also contain information, the CCN Support description, to be used when CCN is enabled in the serving cell, see 3GPP TS 44.060. This CCN Support description is associated with the Neighbour Cell list (see 3.4.1.2.1.3) having the same BA_IND value and 3G_BA_IND value. Each CCN_SUPPORTED bit of t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.2 Test purpose | To verify that the MS does not apply CCN on a target cell when the CCN support description not is set for that cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, PCCCH not present.
Cell A: CCN Active. SI3 indicates SI2quater broad cast on BCCH norm. SI2quater contains a CCN Support Description indicating that CCN not is supported towards Cell B. RLA_C = -50 dBm
Cell B: CCN Active. RLA_C = -60 dBm
Mobile Station:
MS i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8 Network Assisted Cell Change / NC mode change | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.1 Conformance requirements | [3GPP TS 44.060, 8.8.3 & 4)]
The network orders the mobile station into NC2 mode.
A mobile station may in response to a PACKET CELL CHANGE NOTIFICATION message sent to the network receive a PACKET MEASUREMENT ORDER message indicating NC2 mode. When the mobile station receives the NC2 order it shall leave CCN mode, stop... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.2 Test purpose | To verify that the MS leaves the CCN mode and enters NC2 mode on receipt of Packet Measurement Order and the NC2 parameters. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, RXLEV_ACCESS_MIN = -90dBm.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilitie... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9 Network Assisted Cell Change / NC mode change / Packet Neighbour Cell Data | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.1 Conformance requirements | [3GPP TS 44.060, 8.8.3 & 4)]
The network orders the mobile station into NC2 mode.
A mobile station may in response to a PACKET CELL CHANGE NOTIFICATION message sent to the network receive a PACKET MEASUREMENT ORDER message indicating NC2 mode. When the mobile station receives the NC2 order it shall leave CCN mode, stop... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.2 References | 3GPP TS 44.060, subclause 5.5.1.4.3 and 8.8.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.3 Test purpose | 1. To verify that MS leaves CCN mode when it receives a PACKET MEASUREMENT ORDER activating NC2 and follows the NC2 procedures.
2. To verify that MS uses the System Information received in PACKET NEIGHBOUR CELL DATA when accessing the new cell.
3. To verify that MS requests remaining System Information messages when ha... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.1 Initial conditions | System Simulator:
3 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: The indication of Cell C is removed in SI2. RLA_C = -50 dBm
Cell B: Supports PACKET SI STATUS. No System Information is broadcast on the BCCH, except SI3. This is only made to make it possible to ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.3 Test procedure | The MS is triggered to initiate packet uplink transfer. SS assigns resources to the MS and the MS starts to send uplink data that the SS acknowledges. During the uplink transfer, the signal strength of cell A is lowered to – 80 dBm. The MS enters CCN mode and sends PACKET CELL CHANGE NOTIFICATION. The MS then continues... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.