hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6 Packet Enhanced Measurement Report (PEMR) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1 Network Control PEMR – Activation with SI Messages | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.1 Conformance requirement | 1 The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH.
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.2 Test purpose | To verify that the MS sends PEMR following the report type and according to the indicated reporting periods covering GSM neighbour list specified in SI2quater. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 GPRS cells configured as GPRS cells with SI2 quater giving all adjacent ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3 Network Control PEMR – Packet Measurement Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3.1 Conformance requirement | 1 The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH.
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 2 In packet idle mode, the reporting period is NC_REPORTING_PERIOD_I rounded off to the nearest smaller integer multiple of DRX period if NC_REPORTING PERIOD_I is greater than DRX period, else, the reporting period is DRX period | Reference:
3GPP TS 04.60 / 3GPP TS 44.060 subclause 5.6.1
3GPP TS 05.08 / 3GPP TS 45.008 subclause 10.1.4.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3.2 Test purpose | To verify that the MS sends PEMR following the report type and according to the indicated reporting period specified in Packet Measurement Order.
42.4.6.3.3 Method of test
Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4 Network Control PEMR – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.2 Test Purpose | To verify that the MS sends PEMR during uplink packet transfer according to the indicated reporting type and reporting periods specified in SI2quater.
To verify that the MS sends PEMR during uplink packet transfer according to the indicated reporting type and reporting period specified in Packet Measurement Order.
Refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 cells configured as GPRS cells with SI2 quater giving adjacent cell conf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5 Network Control PEMR – Downlink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.2 Test Purpose | To verify that the MS sends PEMR during downlink packet transfer according to the indicated reporting type and reporting periods specified in SI2 quater.
To verify that the MS sends PEMR during downlink packet transfer according to the indicated reporting type and reporting period specified in Packet Measurement Order. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 cells configured as GPRS cells with SI2 quater giving adjacent cell conf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6 Network Control PEMR / Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6.1 Conformance requirement | For (NC) measurement reporting, the Mobile Station shall use PACKET ENHANCED MEASUREMENT REPORT messages instead of PACKET MEASUREMENT REPORT messages if that is indicated by the parameter REPORT_TYPE and if at least one BSIC is allocated to each frequency in the BA(GPRS) list.
Reference:
3GPP TS 04.60 / 3GPP TS 44.060... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6.2 Test purpose | To verify that the MS sends PEMR following the report type specified in Packet Cell Change Order.
42.4.6.6.3 Method of test
Initial conditions
Transmitter
RF Signal Level (dBm)
NCC
BCC
Cell Identity
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.7 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7 Inter-RAT (GPRS to UTRAN) Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1 Inter-RAT Cell Change Order (Known Cell) – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.2 Test Purpose | To verify the when NC2 is commanded, the MS sends PACKET ENHANCED MEASUREMENT REPORT messages, in which both the serving and non-serving cells are reported.
To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall ab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2 Inter-RAT Cell Change Order (Unknown Cell) – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.2 Test Purpose | To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall abort any TBF in progress and stop transmitting.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS (NC2), Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3 Inter-RAT Cell Change Order (Known Cell) – Downlink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.2 Test Purpose | To verify that when the cell change order procedure is started when the MS receives PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25.331 subclause 8.3.10 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4 Inter-RAT Cell Change Order (Known Cell) – Simultaneous uplink and downlink transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.2 Test Purpose | To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall abort any TBF in progress and stop transmitting.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5 Inter-RAT (GPRS to UTRAN) Cell Change Order (Known cell) / Failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1 Inter-RAT (GPRS to UTRAN) Cell Change Order (Known cell) / Failure / Uplink transfer / T3174 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.1 Conformance requirement | In the following cases, the mobile station shall determine that the network controlled cell reselection procedure has failed:
- The PACKET CELL CHANGE ORDER message commands the mobile station to a frequency in a frequency band not supported by the mobile station. Cause: “frequency not implemented”.
- The PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.2 Test Purpose | To verify that an MS in uplink packet transfer mode when commanded by a PACKET CELL CHANGE ORDER, reports a PACKET CELL CHANGE FAILURE on the old GPRS cell due to the expiry of T3174 before receiving response to RRC CONNECTION REQUEST on target UTRAN cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.3 Method of test | Initial conditions
System Simulator:
- 2 cells, Cell A, GPRS Supported without PBCCH, NC2.
- Cell B is a UTRAN cell. UTRAN cell is the better cell of the two cells. It is activated after MS is GPRS attached to Cell A. 3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell B except that T300 an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.1 Conformance requirement | In the following cases, the mobile station shall determine that the network controlled cell reselection procedure has failed:
- The PACKET CELL CHANGE ORDER message commands the mobile station to a frequency in a frequency band not supported by the mobile station. Cause: “frequency not implemented”.
- The PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.2 Test Purpose | To verify that an MS in downlink packet transfer mode when commanded by a PACKET CELL CHANGE ORDER, reports PACKET CELL CHANGE FAILURE on the old GPRS cell if an RRC CONNECTION REJECT with Inter-RAT info set to GSM is received on the target UTRAN cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.3 Method of test | Initial conditions
System Simulator:
- 2 cells, Cell A, GPRS Supported without PBCCH, NC2. Cell B is a UTRAN cell. Cell Selection conditions favour Cell A. 3G Neighbour Cell Description of Cell A refers to UTRAN Cell B. XXX_MUTIRAT_REPORTING is set to 1. REPORT_TYPE is set to indicate the usage of Packet Enhanced Measu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8 NC2 Procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1 NC2 and DRX | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1 NC2 and DRX / NC_NON_DRX_PERIOD / Respect of NC2 non-DRX mode period | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.1 Conformance requirement | There are four cases when the mobile station shall enter a non-DRX mode period.
1) At the transition from the packet transfer mode to the packet idle mode, the mobile station shall enter the Transfer non-DRX mode period.
2) At the transition from the dual transfer mode to the dedicated mode or packet idle mode, the mob... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.2 Test Purpose | To verify that an MS in Idle mode enters and remains in the non-drx mode only for the duration of NC2 non-DRX mode period which is equal to NC_NON_DRX_PERIOD parameter, when it sends a NC measurement report
Reference
3GPP TS 44.060, sub-clause 5.5.1.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS sends a PACKET MEASUREMENT ORDER message to MS. NETWORK_CONTROL_ORDER is commanded to be NC2. NC_NON_D... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period ordered in Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.2 Test Purpose | To verify that when an MS selects a new cell as ordered using a PACKET CELL CHANGE ORDER message, the MS takes into consideration and respects the NC_NON_DRX_PERIOD parameter sent in a PACKET CELL CHANGE ORDER message in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported.
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS sends a PACKET MEASUREMENT ORDER message to MS ordering the MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period broadcast in SI2Quater | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.2 Test Purpose | To verify that when an MS selects a new cell and if no parameters have been brought from the old cell, the MS uses the broadcast measurement parameter NC_NON_DRX_PERIOD from SI2quater if PBCCH is not allocated in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported
SI2quater transmitted (Rest Octet as described in the Specific Message Contents).
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.5 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period / PBCCH absent / Default Value | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.2 Test Purpose | To verify that when an MS selects a new cell and if no parameters have been brought from the old cell, the MS uses the default value of NC_NON_DRX_PERIOD parameter if NC Measurement Parameters are not included in the SI2quater broadcast in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported
SI2quater transmitted (Rest Octet as described in the Specific Message Contents).
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2 User Data vs Measurement Report Sending / Conflict situation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2 User Data vs Measurement Report Sending / Conflict situation / Expiry of T3192 and T3158 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.1 Conformance requirement | The mobile station shall apply to the timer T3158 either the NC_REPORTING_PERIOD_I when in packet idle mode or the NC_REPORTING_PERIOD_T when in packet transfer mode.
On expiry of timer T3158, the mobile station shall restart timer T3158 with the indicated reporting period, perform the measurements and send either the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.2 Test Purpose | To verify that if T3158 expires before the MS leaves Downlink Packet Transfer mode, the MS waits till T3192 expires before it initiate a Packet Access procedure to send PACKET MEASUREMENT REPORT message.
Reference
3GPP TS 04.60, sub-clauses 5.6.1, 9.3.2.6 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
T3192 set to 1500 msec in GPRS_CELL_OPTIONS
Mobile Station:
MS is GPRS attached and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS establishes a downlink TBF.
W... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3 User Data vs Measurement Report Sending / Conflict situation / Expiry of T3182 and T3158 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.1 Conformance requirement | The mobile station shall apply to the timer T3158 either the NC_REPORTING_PERIOD_I when in packet idle mode or the NC_REPORTING_PERIOD_T when in packet transfer mode.
On expiry of timer T3158, the mobile station shall restart timer T3158 with the indicated reporting period, perform the measurements and send either the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.2 Test Purpose | To verify that if T3158 expires before the MS leaves Uplink Packet Transfer mode and after MS has started T3182
1 the MS will send a PACKET MEASUREMENT REPORT to the SS if uplink resource is allocated before the expiry of T3182.
2 the MS will initiate a Access procedure after T3182 is stopped, if no uplink resource is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is GPRS attached and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
An uplink TBF is established.
While the TBF is active SS sends a PACKET MEASU... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4 User Data vs Measurement Report Sending / Conflict situation / Random Access procedure for PMR sending and User Data transmission | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.2 Test Purpose | To verify that if the MS is triggered to send user data while random access procedure is ongoing to send a PACKET MEASUREMENT REPORT message, the MS will continue the random access procedure, send the PACKET MEASUREMENT REPORT message, will return to Idle mode and then will initiate a random access procedure to send u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported, PCCCH absent.
CCCH combined with SDCCH. Max Retrans = 7, TX-INTEGER = 32
SI2quater present
SI2quater transmitted (Rest Octets as described in the Specific Message Contents)
Mobile Station:
MS is GPRS attached and is in Packet Idle mode.
Test PDP context3 esta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3 Network Control measurement reporting and Dedicated connection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1 Network Control measurement reporting / Dedicated connection / Timer Ready expiry | 42.4.8.3.1.1 Conformance requirement |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.1.1 Conformance requirement for R97 and R98 MS | When the mobile station leaves the MM Ready state, the timer T3158 shall be stopped and no more measurement reports shall be sent to the network.
Reference
3GPP TS 04.60, subclauses 5.6.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.1.2 Conformance requirement for R99 and later MS | The parameter values NC1 and NC2 only apply in Ready state. In Standby state, the MS shall always use normal MS control independent of the ordered NC mode.
A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.2 Test Purpose | To verify that some R97 or R98 MS involved in NC measurement reporting, stops its reporting if the Ready Timer expires within a dedicated connection.
For some R97 or R98 MS and for R99 or later MS, the NC measurement reporting is stopped when entering a dedicated connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported. PBCCH not supported. Default Ready Timer (44s)
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmConn)
PIXIT... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2 Network Control measurement reporting / Dedicated connection / Different NC parameters / No T3158 expiry | 42.4.8.3.2.1 Conformance requirement
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. The reporting periods are indicated in the NC_REPORTING_PERIOD_I and NC_REPORTING_PERIOD_T field of the PSI5, the SI2quater, the PACKET CELL CHANGE ORDER or the PACKET MEASUREM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.2 Test Purpose | To verify that a MS involved in NC measurement reporting on a NC2 cell, continue its measurement reporting after a dedicated call, with the same NC parameters for some R97 or R98 MS, and with the broadcasted parameters for other R97 or R98 MS and for R99 and later MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported, NC2, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmConn)
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3 Network Control measurement reporting / Dedicated connection / Handover / No T3158 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 message on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in a PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.2 Test Purpose | To verify that a MS involved in NC measurement reporting and making a handover to a new NC2 cell, uses the broadcasted NC reporting parameters of its new serving cell for its NC measurement reporting. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.3 Method of test | Initial conditions
System Simulator:
2 cells (cell A and cell B), GPRS supported, NC2, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmCon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4 Network Control measurement reporting / Dedicated connection / Different NC parameters / T3158 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.1 Conformance requirement | When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. The reporting periods are indicated in the NC_REPORTING_PERIOD_I and NC_REPORTING_PERIOD_T field of the PSI5, the SI2quater, the PACKET CELL CHANGE ORDER or the PACKET MEASUREMENT ORDER message. If NC_NON_DRX_PERI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.2 Test Purpose | To verify that some R97 or R98 MS involved in NC measurement reporting, sends only its latest PACKET MEASUREMENT REPORT when many reporting periods had expired during a CS call on the same cell.
To verify that some other R97or R98 MS andR99 and later releases MS stop their measurement reporting with the dedicated call ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.