hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4 A-GPS test conditions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.1 General | This sub clause defines the minimum performance requirements for both MS based and MS assisted A‑GPS terminals. If a terminal supports both modes then it shall be tested in both modes. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.2 Measurement parameters | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.2.1 MS based A-GPS measurement parameters | In case of MS-based A-GPS, the measurement parameters are contained in the RRLP LOCATION INFORMATION IE. The measurement parameter is the horizontal position estimate reported by the MS and expressed in latitude/longitude. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.2.2 MS assisted A-GPS measurement parameters | In case of MS-assisted A-GPS, the measurement parameters are contained in the RRLP GPS MEASUREMENT INFORMATION IE. The measurement parameters are the MS GPS Code Phase measurements. The MS GPS Code Phase measurements are converted into a horizontal position estimate using the procedure detailed in sub clause 70.11.4.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.2.3 2D position error | The 2D position error is defined by the horizontal difference in meters between the ellipsoid point reported or calculated from the MS Measurement Report and the actual simulated position of the MS in the test case considered. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.2.4 Response time | Max Response Time is defined as the time starting from the moment that the MS has received the final RRLP MEASURE POSITION REQUEST sent before the MS sends the MEASURE POSITION RESPONSE containing the Location Information or the GPS Measurement Information, and ending when the MS starts sending the MEASURE POSITION RES... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.3 Converting MS-assisted measurement reports into position estimates | To convert the MS measurement reports in case of MS-assisted mode of A-GPS into position errors, a transformation between the "measurement domain" (code-phases, etc.) into the "state" domain (position estimate) is necessary. Such a transformation procedure is outlined in the following sub clauses. The details can be fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.3.1 MS measurement reports | In case of MS-assisted A-GPS, the measurement parameters are contained in the RRLP GPS MEASUREMENT INFORMATION ELEMENT (sub clause A.3.2.5 in 3GPP TS 44.031). The measurement parameters required for calculating the MS position are:
1) Reference Time: The MS has two choices for the Reference Time:
a) "Reference Frame";
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.4.3.2 WLS position solution | The WLS position solution problem is concerned with the task of solving for four unknowns; xu, yu, zu the receiver coordinates in a suitable frame of reference (usually ECEF) and bu the receiver clock bias. It typically requires the following steps:
Step 1: Formation of pseudo-ranges
The observation of code phase repor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5 Sensitivity | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1 Sensitivity Coarse Time Assistance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1.1 Definition | Sensitivity with coarse time assistance is the minimum level of GPS satellite signals required for the MS to make an A-GPS position estimate to a specific accuracy and within a specific response time when the network only provides coarse time assistance. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1.2 Conformance requirement | The first fix position estimates shall meet the accuracy and response time requirements in table 70.11.5.1.2 for the parameters specified in table 70.11.5.1.1.
Table 70.11.5.1.1: Test parameters for Sensitivity Coarse Time Assistance
Parameters
Unit
Value
Number of generated satellites
-
8
HDOP Range
-
1.1 to 1.6
Propa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1.3 Test purpose | To verify the MS's first position estimate meets the Conformance requirement under GPS satellite signal conditions that represent weak signal conditions and with only Coarse Time Assistance provided by the SS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1.4 Method of test | Initial conditions
Test environment: normal; see sub clause A1.2.2.
1. Connect SS and GSS to the MS antenna connector or antenna connectors.
2. Set the GPS test parameters as specified in table 70.11.5.1.3 for GPS scenario #1. Select the first satellite PRN defined in the table in sub clause 5.2.1.2.5 in TS 51.010-7 fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.1.5 Test Requirements | For the parameters specified in table 70.11.5.1.3 the MS shall meet the requirements and the success rate specified in table 70.11.5.1.4 with a confidence level of 95% according to annex A7.2.
Table 70.11.5.1.3: Test parameters for Sensitivity Coarse Time Assistance
Parameters
Unit
Value
Number of generated satellites
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2 Sensitivity Fine Time Assistance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2.1 Definition | Sensitivity with fine time assistance is the minimum level of GPS satellite signals required for the MS to make an A-GPS position estimate to a specific accuracy and within a specific response time when the network provides fine time assistance in addition to coarse time assistance. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2.2 Conformance requirement | The first fix position estimates shall meet the accuracy and response time requirements in table 70.11.5.2.2 for the parameters specified in table 70.11.5.2.1.
Table 70.11.5.2.1: Test parameters for Sensitivity Fine Time Assistance
Parameters
Unit
Value
Number of generated satellites
-
8
HDOP Range
-
1.1 to 1.6
Propaga... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2.3 Test purpose | To verify the MS's first position estimate meets the Conformance requirement under GPS satellite signal conditions that represent weak signal conditions and with Fine Time Assistance provided by the SS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2.4 Method of test | Initial conditions
Test environment: normal; see sub clause A1.2.2.
1. Connect SS and GSS to the MS antenna connector or antenna connectors.
2. Set the GPS test parameters as specified in table 70.11.5.2.3 for GPS scenario #1.
3. Switch on the MS.
4. Set up a voice call according to the generic call set up procedure in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.5.2.5 Test Requirements | For the parameters specified in table 70.11.5.2.3 the MS shall meet the requirements and the success rate specified in table 70.11.5.2.4 with a confidence level of 95% according to annex A7.2.
Table 70.11.5.2.3: Test parameters for Sensitivity Fine Time Assistance
Parameters
Unit
Value
Number of generated satellites
-
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6 Nominal Accuracy | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6.1 Definition | Nominal accuracy is the accuracy of the MS's A-GPS position estimate under ideal GPS signal conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6.2 Conformance requirement | The first fix position estimates shall meet the accuracy and response time requirements in table 70.11.6.2 for the parameters specified in table 70.11.6.1.
Table 70.11.6.1: Test parameters for Nominal Accuracy
Parameters
Unit
Value
Number of generated satellites
-
8
HDOP Range
-
1.1 to 1.6
Propagation conditions
-
AWGN... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6.3 Test purpose | To verify the MS's first position estimate meets the Conformance requirement under GPS satellite signal conditions that represent ideal conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6.4 Method of test | Initial conditions
Test environment: normal; see sub clause A1.2.2.
1. Connect SS and GSS to the MS antenna connector or antenna connectors.
2. Set the GPS test parameters as specified in table 70.11.6.3 for GPS scenario #1.
3. Switch on the MS.
4. Set up a voice call according to the generic call set up procedure in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.6.5 Test Requirements | For the parameters specified in table 70.11.6.3 the MS shall meet the requirements and the success rate specified in table 70.11.6.4 with a confidence level of 95% according to annex A7.2.
Table 70.11.6.3: Test parameters for Nominal Accuracy
Parameters
Unit
Value
Number of generated satellites
-
8
HDOP Range
-
1.1 to... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7 Dynamic Range | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7.1 Definition | Dynamic Range is the maximum difference in level of the GPS signals from a number of satellites that allows the MS to make an A-GPS position estimate with a specific accuracy and a specific response time. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7.2 Conformance requirement | The first fix position estimates shall meet the accuracy and response time requirements in table 70.11.7.2 for the parameters specified in table 70.11.7.1.
Table 70.11.7.1: Test parameters for Dynamic Range
Parameters
Unit
Value
Number of generated satellites
-
6
HDOP Range
-
1.4 to 2.1
GPS Coarse Time assistance error... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7.3 Test purpose | To verify the MS's first position estimate meets the Conformance requirement under GPS satellite signal conditions that have a wide dynamic range. Strong satellites are likely to degrade the acquisition of weaker satellites due to their cross‑correlation products. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7.4 Method of test | Initial conditions
Test environment: normal; see sub clause A1.2.2.
1. Connect SS and GSS to the MS antenna connector or antenna connectors.
2. Set the GPS test parameters as specified in table 70.11.7.3 for GPS scenario #1. Select the first three satellite PRNs defined in the table in sub clause 5.2.1.2.5 in TS 51.01... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.7.5 Test Requirements | For the parameters specified in table 70.11.7.3 the MS shall meet the requirements and the success rate specified in table 70.11.7.4 with a confidence level of 95% according to annex A7.2.
Table 70.11.7.3: Test parameters for Dynamic Range
Parameters
Unit
Value
Number of generated satellites
-
6
HDOP Range
-
1.4 to 2.1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8 Multi-Path scenario | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8.1 Definition | Multi-path performance measures the accuracy and response time of the MS's A-GPS position estimate in a specific GPS signal multi-path environment. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8.2 Conformance requirement | The first fix position estimates shall meet the accuracy and response time requirements in table 70.11.8.2 for the parameters specified in table 70.11.8.1.
Table 70.11.8.1: Test parameters for Multi-Path scenario
Parameters
Unit
Value
Number of generated satellites (see note)
-
5
GPS Coarse Time assistance error range
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8.3 Test purpose | To verify the MS's first position estimate meets the Conformance requirement under GPS satellite signal conditions that represent simple multi-path conditions. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8.4 Method of test | Initial conditions
Test environment: normal; see sub clause A1.2.2.
1. Connect SS and GSS to the MS antenna connector or antenna connectors.
2. Set the GPS test parameters as specified in table 70.11.8.3 for GPS scenario #1. Select the first two satellite PRNs defined in the table in sub clause 5.2.1.2.5 in TS 51.010-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.8.5 Test Requirements | For the parameters specified in table 70.11.8.3 the MS shall meet the requirements and the success rate specified in table 70.11.8.4 with a confidence level of 95% according to annex A7.2.
Table 70.11.8.3: Test parameters for Multi-Path scenario
Parameters
Unit
Value
Number of generated satellites (see note)
-
5
GPS Co... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.12 Assisted GNSS General Procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.12.1 Positioning Capability Transfer procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.12.1.1 Conformance requirement: | When the MS receives a complete POSITIONING CAPABILITY REQUEST message, it shall send the POSITIONING CAPABILITY RESPONSE message. The message shall include the positioning capabilities of the MS and the types of supported assistance data. The message may include the types of assistance needed by the MS to obtain a loc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.12.1.2 Test Purpose | To verify that the MS sends the correct positioning capabilities and the types of supported assistance data in the POSITIONING CAPABILITY RESPONSE message. Note: no positioning procedure is performed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.12.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1 message. The MS performs control early classmark sending to prov... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13 Assisted GNSS Network Induced Location Request (NI-LR) | 70.13.1 NI-LR / Emergency Call on TCH Radio Channel for Mobiles Supporting MS-Based GNSS |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.1.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.1.2 Test Purpose | To verify when a network instigates the LCS positioning procedure using GNSS by sending RRLP (Measure Position Request) message, after a traffic channel has been established during an emergency call, the mobile responds with RRLP (Measure Position Response) containing MS location estimate. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
SIM:
Normal SIM
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub test cases dep... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.2.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.2.2 Test Purpose | To verify when a network instigates the LCS positioning procedure using GNSS by sending RRLP (Measure Position Request) message, after a traffic channel has been established during an emergency call, the mobile responds with RRLP (Measure Position Response) containing A-GNSS measurement values. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.13.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
SIM:
Normal SIM
Specific PICSstatements
-
PIXIT statements
-
Test Procedure
This test case includes sub test cases depe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14 Assisted GNSS Mobile Originated Location Request (MO-LR) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.1 MO-LR / Idle mode for Mobiles Supporting MS-Assisted GNSS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.1.1 Conformance requirements | 1) The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2) The MS invokes self-location request by sending REGISTER message containing Facility IE LCS MO-LR with MOLR-TYPE set to locationEstimate.
3) The MS needs to interact with the network for each separate location request.
4) On re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.1.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the Facility IE LCS MO-LR. When the MS receives a FACILITY message containing a Facility IE MO-LR LCS result carrying the requested location estimate, it clears the transaction by sending a RELEASE COMPLETE messag... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CSKN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.2 MO-LR / Idle mode for Mobiles Supporting MS-Based GNSS / Assistance Data Request | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.2.1 Conformance requirements | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes self-location request by sending REGISTER message containing Facility IE LCS MO-LR with MOLR-TYPE set to assistance data.
3. The MS sends RRLP ASSISTANCE DATA ACK f... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.2.2 Test Purpose | To verify that a MS invokes a self-location request by sending the network a REGISTER message containing an LCS-MOLR REQ of type “Assistance data”. On receipt of each RRLP ASSISTANCE DATA from SS with the requested assistance data, MS shall send RRLP ASSISTANCE ACK for each component to SS. When the MS receives a FACIL... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CSKN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.3 MO-LR / Idle mode for Mobiles Supporting MS-Based GNSS / Location Estimate Request | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.3.1 Conformance requirements | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes self-location request by sending REGISTER message containing Facility IE LCS MO-LR with MOLR-TYPE set to locationEstimate.
3. On receiving the POSITIONING CAPABILIT... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.3.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing an MO-LR Request of type “locationEstimate”. When the MS receives a FACILITY message containing a MO-LR return result carrying the requested location estimate, it clears the transaction by sending a RELEASE COMPLE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.3.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CSKN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.4 MO-LR / Dedicated Mode for Mobiles Supporting MS-Assisted GNSS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.4.1 Conformance Requirement: | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke com... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.4.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the Facility IE LCS MO-LR on an already established speech call related main DCCH (FACCH). When the MS receives a FACILITY message containing a Facility IE MO-LR LCS result carrying the requested location estimate... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.4.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS has valid TMSI and CSKN.
The MS is brought into the state U10 by using table 26.8.1.2/3.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.5 MO-LR / Dedicated Mode for Mobiles Supporting MS-Based GNSS / Assistance Data Request | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.5.1 Conformance Requirement: | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes self-location request by sending a REGISTER message containing a LCS MO LR invoke
component with MO LR-TYPE set to ASSISTANCE DATA, LOCATION_METHOD TYPE set
ASSISTE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.5.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the FACILITY IE LCS-MOLR REQ on an already established speech call related main DCCH (FACCH). On receipt of a RRLP ASSISTANCE DATA from SS with the requested assistance data, MS shall send back RRLP ASSISTANCE ACK... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.5.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS has valid TMSI and CSKN.
The MS is brought into the state U10 by using table 26.8.1.2/3
Specific PICS statements
-
PIXIT statements
-
Test Procedure:
This test case includes sub-test cas... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.6 MO-LR / Dedicated Mode for Mobiles Supporting MS-Based GNSS / Location Estimate request | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.6.1 Conformance requirements: | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke component.
3. On receiving the POSITIONING CAPABILITY REQUEST message the MS respo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.6.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing an MO-LR Request of type “locationEstimate” on an already established speech call related SACCH. When the MS receives a FACILITY message containing a MO-LR return result carrying the requested location estimate, i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.6.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS has valid TMSI and CKSN.
The MS is brought into state U10 by using table 26.8.1.2/3.
Test Procedure:
This test case includes sub-test cases dependent on the GNSS supported by the MS. Each... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8 MO-LR / Location Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.1 MO-LR / Location Error / Requested Method not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.1.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.1.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall send back RRLP MEASURE POSITION RESPONSE message with Location Error component if the MS does not support the requested method. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, the MS sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure:
This test case includes sub-test cases dependent on the GNSS supported... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.2 MO-LR / Location Error / GNSS Assistance Data Missing | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.2.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.2.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall send back RRLP MEASURE POSITION RESPONSE message with Location Error component if GNSS assistance data is missing. On receipt of second RRLP MEASURE POSITION REQUEST (with GNSS assistance data included) from SS to start th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.8.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure:
This test case includes sub-test cases dependent on the GNSS supported... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.9 MO-LR / Multiple RRLP Requests with Same Reference Number and Extended Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.9.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.9.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall ignore the second RRLP MEASURE POSITION REQUEST if the second RRLP MEASURE POSITION REQUEST has the same REFERENCE NUMBER and the same Extended Reference IE as in the previous one. The MS shall send back RRLP MEASURE POSIT... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.9.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.10 MO-LR / Multiple RRLP Requests with Different Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.10.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.10.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if the second RRLP MEASURE POSITION REQUEST is received with a different REFERENCE NUMBER and the same EXTENDED REFERENCE IE as the first one. The MS shall perform the measurement... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.10.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.11 MO-LR / Multiple RRLP Requests with Different Extended Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.11.1 Conformance requirements | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.11.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if the second RRLP MEASURE POSITION REQUEST is received with the same REFERENCE NUMBER as the first one and a different EXTENDED REFERENCE IE. The MS shall perform the measurement... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.11.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
This test case includes sub-test cases dependent on the GNSS sup... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.14.12 MO-LR / RR Management Commands |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.