hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6 E-OTD Timing Measurement Accuracy | Scope of Tests
This test procedure plan is intended verify the operation of Enhanced Observed Timing Difference (E-OTD) measurement functionality from an E-OTD capable GSM Mobile Station (MS).
The scope of this test plan is limited to verification of the MS physical layer against 3GPP TS 05.05, Release 1999, version 8.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1 E-OTD Accuracy, Sensitivity Performance Tests using GMSK Signals | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a neighbor shall not exceed 100 nanoseconds and 300 nanoseconds at a minimum neighbor carrier signal strength relative to relative sensitivity levels of 12 dB and –8 dB respectively, as specified in 3GPP TS 05.05, annex I, sub clause I.2.1, table I.2.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Nearby neighbor stations that provide a relatively high C/N to the MS receiver should result in greater measurement accuracy than those further away wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.4 Method of Test | Initial Configuration
Neighbor Cell: One neighbor cells with a minimum configuration of a BCCH in order to allow the MS to perform the required measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Table 70.6.1-1 and Tab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.5 Test procedure | a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7.
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dB.
c) Disable the interfering signal generator.
d) Configure the neighbor base station simulator s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.1.5 is within the test conformance requirements listed in Table 70.6.1-3
Table 70.6.1-3, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.1, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2 E-OTD Accuracy, Interference Performance Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving an 8PSK neighbor with a co-channel interference ratio of 0 dB shall not exceed 300 nanoseconds, 10dB not exceeding 300 nanoseconds, adjacent channel interference ratio of –18dB not exceeding 500 nanoseconds, -8 dB not exceeding 200 nanoseconds, as well as an ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. As the C/I ratio due to neighbor cell co-channel interference is reduced, E-OTD measurement accuracy may be reduced as well.
The purpose of this test c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.4 Method of Test | Initial Configuration
Neighbor Cells: at least two neighbor cells with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.5 Test procedure | Co-Channel test procedure at 0dB C/I:
a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Enable the interfering signal generator on the frequenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.2.5 is within the test conformance requirements listed in Table 70.6.2-1.
Table 70.6.2-1, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.2, Test Conformance R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a TU3 Rayleigh-faded neighbor shall not exceed 1.5 microseconds, as specified in 3GPP TS 05.05, Release 99, Version 8.7.1, Annex I, Clause I.2.3, Table I.2.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Rayleigh fading to the neighbor cell will reduce E-OTD measurement accuracy.
The purpose of this test case is to verify that an E-OTD capable MS can pr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.4 Method of Test | Initial Configuration
Neighbor Cell: at least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Ta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.5 Test procedure | a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Disable the interfering signal generator
d) Configure the neighbor base station simulator suc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.6 Test Requirements | Verify that the RMS90 error calculated in Step i) is < 1.5 microseconds |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4 E-OTD Accuracy, Interference Performance Tests, 8PSK BCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.4 Method of Test | Initial Configuration
Neighbor Cells: at least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.5 Test procedure | Co-Channel 8PSK test procedure at 0dB C/I:
a) Configure serving base station simulator to transmit in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Enable the interfering signal generator on the frequency of the nei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.4.5 is within the test conformance requirements listed in Table 70.6.4-1
Table 70.6.4-1, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.4, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5 E-OTD Accuracy, Multipath Performance Test, 8PSK BCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a TU3 Rayleigh-faded 8PSK-modulated neighbor shall not exceed 1.5 microseconds, as specified in 3GPP TS 05.05, Release 99, Annex I, Clause I.2.3, Table I.2.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Rayleigh fading to the neighbor cell will reduce E-OTD measurement accuracy.
The purpose of this test case is to verify that an E-OTD capable MS can pr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.4 Method of Test | Initial Configuration
Neighbor Cells: At least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Ta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.5 Test procedure | a) Configure serving base station simulator to transmit 8PSK bursts modulated with pseudo-random data in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Disable the interfering signal generator
d) Configure the neighbo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.6 Test Requirements | Verify that the RMS90 error calculated in Step i) is < 1.5 microseconds |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6 E-OTD Accuracy, Sensitivity Performance Tests for 8PSK Modulated signals | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a neighbor shall not exceed 100 nanoseconds and 300 nanoseconds at a minimum neighbor carrier signal strength relative to relative sensitivity levels of 12 dB and –8 dB respectively, as specified in 3GPP TS 05.05, annex I, sub clause I.2.1, table I.2.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Nearby neighbor stations that provide a relatively high C/N to the MS receiver should result in greater measurement accuracy than those further away wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.4 Method of Test | Initial Configuration
Neighbor Cell: One-neighbor cells with a minimum configuration of a BCCH in order to allow the MS to perform the required measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Table 70.6.6-1 and Tab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.5 Test procedure | a) Configure serving base station simulator to transmit 8PSK bursts in time slots 1 through 7.
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm.
c) Disable the interfering signal generator.
d) Configure the neighbor base station simulator such t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.6.5 is within the test conformance requirements listed in Table 70.6.6-3
Table 70.6.6-3, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.6, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7 Assisted GPS Network Induced Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4 Network Induced Location Request Emergency Call on TCH Radio Channel | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1 Network Induced Location Request Emergency Call on TCH Radio Channel for Mobiles Supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.2 Test Purpose | To verify when a network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) message, after a traffic channel has been established during an emergency call, the mobile responds with RRLP (Measure Position Response) containing MS location estimate. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
SIM:
Normal SIM
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
An Emergency Call is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.2 Network Induced Location Request Emergency Call on TCH Radio Channel for mobiles supporting MS-Assisted GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.2.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.2.2 Test Purpose | To verify when a network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) message, after a traffic channel has been established during an emergency call, the mobile responds with RRLP (Measure Position Response) containing A-GPS measurement values. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
An Emergency Call is initiated with th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.3 Network Induced Location Request Emergency Call on TCH Radio Channel, no IMSI for Mobiles Supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.3.1 Conformance requirements | 1. With the MS (no SIM inserted) in the "idle, no IMSI" state, the user shall initiate an emergency call by dialling the number 112 (for GSM 900 and 1 800 MSs), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS 1 900 MS in the USA 1 900 MS), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS MS in Mexico). The MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.3.2 Test Purpose | To verify when an emergency call is initiated by an MS that does not have a SIM fitted, the network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) message and the mobile responds with RRLP (Measure Position Response) containing MS location. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.3.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, no IMSI”, no SIM inserted.
SIM:
No SIM.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
An Emergency Call is initiated by... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.4 Network Induced Location Request Emergency Call on TCH Radio Channel, no IMSI for mobiles supporting MS-Assisted GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.4.1 Conformance requirements | 1. With the MS (no SIM inserted) in the "idle, no IMSI" state, the user shall initiate an emergency call by dialling the number 112 (for GSM 900 and 1 800 MSs), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS 1 900 MS in Mexico). Th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.4.2 Test Purpose | To verify when an emergency call is initiated by an MS that does not have a SIM fitted, the network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) message and the mobile responds with RRLP (Measure Position Response) containing A-GPS measurement values. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.4.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, no IMSI”, no SIM inserted.
SIM:
No SIM.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
An Emergency Call is initiated by the MS, with no SIM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8 Assisted GPS Mobile Originated Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.1 Basic Self Location | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.1.1 Conformance requirements | 1) The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2) The MS invokes self-location request by sending REGISTER message containing Facility IE LCS MO-LR with MOLR-TYPE set to locationEstimate.
3) The MS needs to interact with the network for each separate location request.
4) On re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.1.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the Facility IE LCS MO-LR. When the MS receives a FACILITY message containing a Facility IE MO-LR LCS result carrying the requested location estimate, it clears the transaction by sending a RELEASE COMPLETE messag... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CSKN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
The MS invokes call independent supplem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.2 Basic Self Location in Dedicated Mode | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.2.1 Conformance requirements | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke com... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.2.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the Facility IE LCS MO-LR on an already established speech call related main DCCH (FACCH). When the MS receives a FACILITY message containing a Facility IE MO-LR LCS result carrying the requested location estimate... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS has valid TMSI and CSKN.
The MS is brought into the state U10 by using table 26.8.1.2/3.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
The MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.3 Transfer to 3rd Party | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.3.1 Conformance requirements | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time). If the MS is requesting that its location be sent to another LCS client, the message shall include t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.3.2 Test Purpose | To verify that the MS invokes a transfer of its own location to a 3rd party LCS Client by sending the network a REGISTER message containing the Facility IE LCS MO-LR with LCSClientExternalID present. The network sends location information of the MS to another LCS Client, and then it clears the transaction by sending a ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.3.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
The MS invokes call independent supplem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4 MO-LR Positioning Measurement | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.1 MO-LR Positioning Measurement / Protocol Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.1.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.1.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. The MS shall send a RRLP PROTOCOL ERROR message to SS with specific error code if RRLP MEASURE POSITION REQUEST is incomplete. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, MS shall send back ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
A MOLR procedure as call independent supplementar... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2 MO-LR Positioning Measurement / Location Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.1 Location Error: Requested Method not Supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.1.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.1.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall send back RRLP MEASURE POSITION RESPONSE message with Location Error component if the MS does not support the requested method. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, the MS sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
A MOLR procedure as call independent supplementar... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.2 Location Error: GPS Assistance Data Missing | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.2.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.2.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall send back RRLP MEASURE POSITION RESPONSE message with Location Error component if GPS assistance data is missing. On receipt of second RRLP MEASURE POSITION REQUEST (with GPS assistance data included) from SS to start the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.2.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The A-GPS assistance data stored in the MS is res... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.3 MO-LR Positioning Measurement / Multiple RRLP Requests with Same Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.3.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.3.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall ignore the second RRLP MEASURE POSITION REQUEST if the second RRLP MEASURE POSITION REQUEST has the same REFERENCE NUMBER as in the previous one. The MS shall send back RRLP MEASURE POSITION RESPONSE to SS after finishing ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.3.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
A MOLR procedure as call independent supple... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.4 MO-LR Positioning Measurement / Multiple RRLP Requests with Different Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.4.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.4.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if the second RRLP MEASURE POSITION REQUEST is received with a different REFERENCE NUMBER. The MS shall perform the measurement according to the newly received RRLP MEASURE POSITI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.4.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
A MOLR procedure as call independent supple... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.5 MO-LR Positioning Measurement / RR Management Commands | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.5.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.5.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if a RR MANAGEMENT command is received during the measurement procedure. The MS shall send a RR MANAGEMENT RESPONSE message to SS when the RR MANAGEMENT procedure is complete. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.4.5.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
A MOLR procedure as call independent supple... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.