hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5 MO_LR Basic Self Location Request for MS-Based AGPS | The test cases in this sub clause focus on Mobile Originating Location Request using MS-Based AGPS method. A MO-LR procedure could occur for requesting assistance data for mobile’s own location. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.1 MO_LR Basic Self Location Request in Idle Mode (Normal Case) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.1.1 Conformance requirements: | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes self-location request by sending a REGISTER message containing a LCS-MOLR invoke component with MO_LR TYPE set to ASSISTANCE DATA, LOCATION_METHOD TYPE set ASSISTED... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.1.2 Test Purpose | To verify that a MS invokes a self-location request by sending the network a REGISTER message containing FACILITY IE LCS-MOLR REQ. On receipt of each of RRLP ASSISTANCE DATA from SS with the requested assistance data, MS shall send RRLP ASSISTANCE ACK for each component to SS. When the MS receives a FACILITY message co... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.1.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test Procedure:
A MOLR procedure as call independent supplementary services is initiated from the MS. The MS performs control earl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.2 MO_LR Basic Self Location Request in Dedicated Mode (Normal case) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.2.1 Conformance Requirement: | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes self-location request by sending a REGISTER message containing a LCS-MOLR invoke
component with MO_LR TYPE set to ASSISTANCE DATA, LOCATION_METHOD TYPE set
ASSISTED... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.2.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing the FACILITY IE LCS-MOLR REQ on an already established speech call related main DCCH (FACCH). On receipt of a RRLP ASSISTANCE DATA from SS with the requested assistance data, MS shall send back RRLP ASSISTANCE ACK... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS has valid TMSI and CSKN.
The MS is brought into the state U10 by using table 26.8.1.2/3
Test Procedure:
A MOLR procedure as call independent supplementary services is initiated from the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.3 MO_LR Basic Self Location Request in Idle Mode (Alternative Case) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.3.1 Conformance requirements: | The following requirements apply for this test:
1. If the MS is in idle mode, the MS requests an SDCCH and sends a DTAP CM service request indicating a request for call independent supplementary services to the BSC.
2. The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke comp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.3.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing an MO-LR Request of type “locationEstimate”. When the MS receives a FACILITY message containing a MO-LR return result carrying the requested location estimate, it clears the transaction by sending a RELEASE COMPLE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.3.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test Procedure:
The MS invokes call independent supplementary service through a CM SERVICE REQUEST. The SS initiates authenticatio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.4 MO_LR Basic Self Location Request in Dedicated Mode (Alternative Case) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.4.1 Conformance requirements: | The following requirements apply for this test:
1. The MS sends CM SERVICE REQUEST to network for call independent supplementary service.
2. The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke component. SS Version Indicator value 1 or above shall be used.
3. On receiving an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.4.2 Test Purpose | To verify that the MS invokes a self-location request by sending the network a REGISTER message containing an MO-LR Request of type “locationEstimate” on an already established speech call related SACCH. When the MS receives a FACILITY message containing a MO-LR return result carrying the requested location estimate, i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.5.4.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS has valid TMSI and CKSN.
The MS is brought into state U10 by using table 26.8.1.2/3.
Test Procedure:
The MS invokes call independent supplementary service on an existing SACCH channel. Af... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.6 MO-LR Transfer to 3rd Party for MS-Based A-GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.6.1 Conformance requirements | The following requirements apply for this test:
1. If the MS is in idle mode, the MS requests an SDCCH and sends a DTAP CM service request indicating a request for call independent supplementary services to the BSC.
2. The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke comp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.6.2 Test Purpose | To verify that the MS invokes a transfer of its own location to a 3rd party LCS Client by sending the network a REGISTER message containing the Facility IE LCS MO-LR with LCSClientExternalID present. After receiving a FACILITY message as confirmation that the location estimate has been transferred to the requested LCS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.8.6.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
The MS invokes call independent supplem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9 Assisted GPS Mobile Terminated Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1 MT-LR Location Notification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.1 MT-LR Location Notification for Mobiles Supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.1.1 Conformance requirements | 1. The network invokes a location notification procedure by sending a REGISTER message containing a LCS-LocationNotification invoke component to the MS with notificationType set to notifyLocationAllowed. The MS shall notify the MS user of the location request.
2. The MS shall terminate the dialogue by sending a RELEASE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.1.2 Test Purpose | To verify that when the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to NotifyLocationAllowed, the MS displays information about the LCS client correctly and sends a RELEASE COMPLETE message containing a LocationNotification return result with verificationResponse set to p... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After sending the CIPHERING MODE COMPLETE me... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.2 MT-LR Location Notification for Mobiles Supporting MS-Assisted GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.2.1 Conformance requirements | 1. The network invokes a location notification procedure by sending a REGISTER message containing a LCS-LocationNotification invoke component to the MS with notificationType set to notifyLocationAllowed. The MS shall notify the MS user of the location request.
2. The MS shall terminate the dialogue by sending a RELEASE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.2.2 Test Purpose | To verify that when the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to NotifyLocationAllowed, the MS displays information about the LCS client correctly and sends a RELEASE COMPLETE message containing a LocationNotification return result with verificationResponse set to p... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.1.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After sending the CIPHERING MODE COMPLETE me... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2 MT-LR Privacy Options/Verification – Location Allowed If No Response | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.1 MT-LR Privacy Options/Verification– Location Allowed If No Response for mobiles supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.1.1 Conformance requirements | 1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationAllowedIfNoResponse. The MS: a) notifies the user of the request, b) indicates the default is location allowed if no response is received within a predetermined period, and c) provid... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.1.2 Test Purpose | To verify that the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationAllowedIfNoResponse, the MS displays information about the LCS client correctly and indicates that the default response is location allowed if no response is sent. Gives the user the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
- MS LCS Notification timeout timer
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After send... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.2 MT-LR Privacy Options/Verification– Location Allowed If No Response for Mobiles Supporting MS-Assisted GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.2.1 Conformance requirements | 1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationAllowedIfNoResponse. The MS: a) notifies the user of the request, b) indicates the default is location allowed if no response is received within a predetermined period, and c) provid... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.2.2 Test Purpose | To verify that the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationAllowedIfNoResponse, the MS displays information about the LCS client correctly and indicates that the default response is location allowed if no response is sent. Gives the user the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.2.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
- MS LCS Notification timeout timer
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After sendi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3 MT-LR Privacy Options/Verification – Location Not Allowed If No Response | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.1 MT-LR Privacy Options/Verification– Location Not Allowed If No Response for Mobiles Supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.1.1 Conformance requirements | 1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationNotAllowedIfNoResponse, the MS: a) notifies the user of the request, b) indicates the default is location not allowed if no response is received within a predetermined period, and c)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.1.2 Test Purpose | To verify that if the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationNotAllowedIfNoResponse, then the MS displays information about the LCS client correctly and indicates that the default response is location not allowed if no response is sent. Giv... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
- MS LCS Notification timeout timer
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After sendi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.2 MT-LR Privacy Options/Verification– Location Not Allowed If No Response for mobiles supporting MS-Assisted GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.2.1 Conformance requirements | 1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationNotAllowedIfNoResponse, the MS: a) notifies the user of the request, b) indicates the default is location not allowed if no response is received within a predetermined period, and c)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.2.2 Test Purpose | To verify that the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationNotAllowedIfNoResponse, the MS displays information about the LCS client correctly and indicates that the default response is location not allowed if no response is sent. Gives the u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.3.2.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valid TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
- MS LCS Notification timeout timer
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 message. After sendi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4 MT-LR / RRLP Error Handling for MS-Based A-GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.1 RRLP Protocol Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.1.1 Conformance requirement: | The MS sends an RRLP PROTOCOL ERROR message to the network if there is a problem that prevents the MS to receive a complete and understandable RRLP MEASURE POSITION REQUEST component.
Test References
3GPP TS04.31 sub clause 2.2, 2.5 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.1.2 Test Purpose | To verify that the MS sends the correct positioning capability via controled early classmark sending. The MS shall send a RRLP PROTOCOL ERROR message to SS with specific error code if RRLP MEASURE POSITION REQUEST is incomplete. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, MS sha... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1 mess... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.2 RRLP Location Error – Requested Method Not Supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.2.1 Conformance requirement: | The MS sends an RRLP MEASURE POSITION RESPONSE message to the network containing a Location Error component with an error indication if the measurement is not possible.
Test References
3GPP TS04.31 sub clause 2.2, A.3.2.6 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.2.2 Test Purpose | To verify that the MS sends the correct positioning capability via controled early classmark sending. The MS shall send a RRLP MEASURE POSITION RESPONSE message with Location Error component if the MS does not support the requested method. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurem... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1 mess... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.3 RRLP Location Error – GPS Assistance Data Missing | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.3.1 Conformance requirement | The MS sends an RRLP MEASURE POSITION RESPONSE message to the network containing a Location Error component with an error indication if the measurement is not possible.
Test References
3GPP TS04.31 sub clause 2.2, A.3.2.6 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.3.2 Test Purpose | To verify that the MS sends the correct positioning capability via controled early classmark sending. The MS shall send a RRLP MEASURE POSITION RESPONSE message with Location Error component if some GPS assistance data are missing. On receipt of second RRLP MEASURE POSITION REQUEST (with all necessary GPS assistance da... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.3.3 Method of Test | Initial Conditions
System Simulator:
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
The A-GPS assistance data stored in the MS is reset... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.4 Multiple RRLP Requests with same Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.4.1 Conformance requirement: | When after reception of a Measure Position Request component, but before responding with a Measure Position Response or Protocol Error Component, the MS receives a new RRLP message with the Measure Position Request component, the MS ignores the latter component if the old and new RRLP Measure Position Request component... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.4.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall ignore the second RRLP MEASURE POSITION REQUEST if the second RRLP MEASURE POSITION REQUEST has the same REFERENCE NUMBER as in the previous one. The MS shall send back RRLP MEASURE POSITION RESPONSE to SS after finishing ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.4.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.5 Multiple RRLP Requests with different Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.5.1 Conformance requirement: | When after reception of a Measure Position Request component, but before responding with a Measure Position Response or Protocol Error Component, the MS receives a new RRLP message with the Measure Position Request component, the MS aborts activity for the former component, and starts to act according to the latter com... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.5.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if the second RRLP MEASURE POSITION REQUEST is received with a different REFERENCE NUMBER. The MS shall perform the measurement according to the newly received RRLP MEASURE POSITI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.5.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.6 RR Management Commands | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.6.1 Conformance requirement | A target MS shall terminate any positioning procedure or the transfer of RRLP positioning assistance data without sending any response to the SMLC if any RR message is received from the BSC that starts some other RR management procedure, including a new positioning procedure. The new RR procedure shall then be executed... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.6.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if an RR MANAGEMENT command is received during the measurement procedure. The MS shall send an RR MANAGEMENT RESPONSE message to SS when the RR MANAGEMENT procedure is complete. T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.9.4.6.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: default parameters.
Satellite signals: No GPS signal available.
Mobile Station:
The MS is MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10 Conventional GPS Network Induced Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2 Network Induced Location Request Emergency Call on TCH Radio Channel | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1 Network Induced Location Request Emergency Call on TCH Radio Channel for Mobiles Supporting Conventional GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.2 References | 3GPP TS 04.08/44.018 sub clauses 3.3.1.1 and 9.1.11.
3GPP TS 04.08/24.008 sub clauses 4.5.1.5, 5.2.1, 9.2.9, 10.5.1.6, 10.5.1.7.
3GPP TS 02.30 sub clause 4.
3GPP TS 04.31 sub clause 2.2.
70.10.2.1.3Test Purpose
To verify when a network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.4 Method of Test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.5 Initial Conditions | System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
SIM:
Normal SIM
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
- |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.6 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.7 Test Procedure | An Emergency Call is initiated with the MS. SIM card is included in the MS.
The emergency call is established with a late assignment.
After receiving the CONNECT ACKNOWLEDGE message from the MS, the SS sends an RR APPLICATION INFORMATION message containing an RRLP Measure Position Request on FACCH.
The MS then performs... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.8 Maximum duration of the test | 5 minutes. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.9 Expected Sequence | Step
Direction
Message
Comments
1
MS
The appropriate “emergency call number" is entered.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishm... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.10 Specific Message Contents | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.10.1 RR APPLICATION INFORMATION | Information element
Value/remark
Protocol Discriminator
RR Management Protocol (0110)
Skip Indicator
Message Type
Application Information Message type
APDU ID
APDU ID -> RRLP => 0000
APDU Flags
Bit1=0 -> Last or only segment
Bit2=0 -> First or only segment
Bit3=0 -> Command or Final Response
Bit4=spare
APDU Data
2-N By... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.10.2 RRLP Measure Position Request | Information element
Type
Value/remark
ASN.1 encoded
-
referenceNumber
Integer,0 to 7
1
component
CHOICE
msrPositionReq
methodType
CHOICE
msBased
positionMethod
ENUMERATED
gps
measureResponseTime
Integer 0 to 7
7
accuracy
Integer (0-127)
127
useMultipleSets
ENUMERATED
oneSet
extended-reference
SEQUENCE
Rel 5 and later |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.10.2.1.10.3 RRLP Measure Position Response | Information element
Type
Value/remark
ASN.1 encoded
-
referenceNumber
Integer,0 to 7
1
component
CHOICE
msrPositionRsp
A valid response will contain locationInfo otherwise locationError will be returned
locationInfo
SEQUENCE
Any value is acceptable.
locationError
SEQUENCE
Any error value is acceptable.
extended-referen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11 A-GPS Minimum Performance tests | This sub clause specifies the measurement procedures for the conformance test of the minimum performance requirements for GSM user equipment (MS) where the only Assisted Global Navigation Satellite System (A-GNSS) supported is Assisted Global Positioning System (A-GPS) L1 C/A. The procedures for MSs that support other... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.1 Abbreviations | A-GPS Assisted - Global Positioning System
A-GNSS Assisted Global Navigation Satellite System
C/A Coarse/Acquisition
ECEF Earth Centred, Earth Fixed
GPS Global Positioning System
GSS GPS System Simulator
HDOP Horizontal Dilution Of Precision
LOS Line Of Sight
WLS Weighted Least Square |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.2 GPS test conditions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.2.1 GPS signals | The GPS signal is defined at the A-GPS antenna connector of the MS. For MS with integral antenna only, a reference antenna with a gain of 0 dBi is assumed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.2.2 GPS frequency | The GPS signals shall be transmitted with a frequency accuracy of 0.025 PPM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.2.3 GPS static propagation conditions | The propagation for the static performance measurement is an Additive White Gaussian Noise (AWGN) environment. No fading and multi-paths exist for this propagation model. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.2.4 GPS multi-path conditions | Doppler frequency difference between direct and reflected signal paths is applied to the carrier and code frequencies. The Carrier and Code Doppler frequencies of LOS and multi-path for GPS L1 signal are defined in table 70.11.2.1.
Table 70.11.2.1: Multi-path Conditions for GPS Signals
Initial relative Delay
[GPS chip]... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.3 GSM test conditions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.3.1 GSM frequency band and frequency range | The tests in this sub clause are performed on one of the mid range ARFCNs of the GSM operating frequency band of the MS. The ARFCNs to be used for mid range are defined in Table 3.3
If the MS supports multiple frequency bands then the Sensitivity tests in sub clause 70.11.5 shall be repeated in each supported frequency... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.11.3.2 GSM frequency | For all tests the GSM frequency shall be offset with respect to the nominal frequency by an amount equal to the sum of +0.025 PPM and the offset in PPM of the actual transmitted GPS carrier frequency with respect to the nominal GPS frequency. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.