hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.2.1 3.84 Mcps TDD Option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.2.2 1.28 Mcps TDD Option | For the parameters specified in Table7.8.1 the BLER should not exceed the piece-wise linear BLER curve specified in Table 7.8.2.
Table 7.8.1: DCH parameters in birth-death propagation conditions (1.28 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Number of DPCHo
8
2
Scrambling code and basic midamble code number*
0
0
... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.2.3 7.68 Mcps TDD Option | void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a moving propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS and an AWGN noise source to the UE antenna connector as shown in figure A.10. In case of UE-receive diversity connect according to figure A.17.
2. Set up a call according to the Generic call s... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.4.2 Procedure | 1. Measure BLER of DCH. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.5.1 3.84 Mcps option | Void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.5.2 1.28 Mcps option | For the parameters specified in table 7.8.3 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.8.4.
Table 7.8.3: DCH parameters in birth-death propagation conditions
Parameters
Unit
Test 1
Test 2
Number of DPCHo
8
2
Scrambling code and basic midamble code number*
0
0
DPCH ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.8.5.3 7.68 Mcps option | Void.
8 Requirements for Support of RRM |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.1 General | Void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2 Idle Mode Tasks | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.1 RF Cell Selection Scenario | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.1.1 Introduction | After a UE has switched on and a PLMN has been selected, the Cell selection process takes place, as described in TS 25.304. This process allows the UE to select a suitable cell where to camp on in order to access available services. In this process the UE can use stored information (Stored information cell selection) o... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2 Cell Re-Selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1 Scenario 1: Cell re-selection to intra frequency TDD cell | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.1.1 3,84 Mcps TDD Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.1.2 1,28 Mcps TDD Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on cell 2.
This test is applicable to 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.1.3 7,68 Mcps TDD Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.2.1 3,84 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.2.2 1,28 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
TevaluateNTDD: A DRX cycl... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.2.3 7,68 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle le... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.3 Test purpose | This test is to verify the requirement for the cell re-selection delay in the single carrier case |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1 and table 8.2.2.1.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.1.1: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
C... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2 1,28 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1A and 8.2.2.1.2A.
Table 8.2.2.1.1A: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final con... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for SYNCH-UL sequence in the UpPTS for sending for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parame... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3 7,68 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1B and table 8.2.2.1.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.1.1B: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cel... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.1 3,84 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.2 1,28 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of successful tests shall be more than 90% with a confi... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.3 7,68 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2 Scenario 2: Cell re-selection to inter-frequency TDD cell | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on cell 2.
This test is applicable to 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell, and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.1 3,84 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.NOTE:
The cell re-selection delay can be expressed ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.2 1,28 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
TevaluateNTDD A DRX cycle length of 1280ms is assumed for thi... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.3 7,68 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this t... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.3 Test purpose | This test is to verify the requirement for the cell re-selection delay in the multi carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1 and table 8.2.2.2.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1: General test parameters for Cell Re-selection to inter-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1A and table 8.2.2.2.2A. For this test purpose the broadcast repetition period of the target cell shall be 1.28s. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1A: General test parameters for Cell Re-selec... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3 7,68 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1B and table 8.2.2.2.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1B: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active ce... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.1 3,84 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.2 1,28 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of successful tests shall be more than 90% with a confi... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.3 7,68 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3 Scenario 3: TDD/FDD Cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
This test is... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on cell 2.
This test is for the case where the UE camps on a 1,2... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
This test is... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.1 3,84 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD See TS 25.... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.2 1,28 Mcps TDD Option | The minimum requirement for the cell re-selection delay is less than 8 s with a DRX cycle length of 1280ms.
This shall be verified in more than 90% of the cases with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2]clauses 4.2.2 and A4.2.3.
NOTE: The cell re-selection delay can be... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.3 7,68 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD A DRX cycle l... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.3 Test purpose | The test purpose is to verify the requirement for the cell re-selection. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1.1 Initial conditions | This scenario implies the presence of 1 TDD and 1 FDD cell as given in table 8.2.2.3.4.1 and table 8.2.2.3.4.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.3.4.1: General test parameters for the TDD/FDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
TDD ce... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The S... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2.1 Initial Conditions | This test is to verify the requirement for the 1,28 Mcps TDD OPTION/FDD cell re-selection delay reported in clause 4.2. in [2]
This scenario implies the presence 1.28Mps TDD serving cell, and 1 FDD cell to be selected. The UE is requested to monitor neighbouring cells on 1 1.28Mcps TDD carrier and 1 FDD carrier. Test p... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The S... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3 7,68 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3.1 Initial conditions | This scenario implies the presence of 1 TDD and 1 FDD cell as given in table 8.2.2.3.4.1B and table 8.2.2.3.4.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.3.4.1B: General test parameters for the TDD/FDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
TDD... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The S... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.1 3,84 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.2 1,28 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.3 7,68 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4 Scenario 4: inter RAT cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 3,84... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send LOCATION UPDATING REQUEST message to perform a Location update.
This test is for the case where the UE camps on a 1,28 Mcps TDD cell and reselects to a GSM cell.
The req... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 7,68... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.1 3,84 Mcps Option | The cell re-selection delay shall be less than 26 s + TBCCH, where TBCCH is the maximum time allowed to read BCCH data in the GSM cell.
NOTE: The cell re-selection delay can be expressed as:
4 * TmeasureGSM + TBCCH
where:
TmeasureGSM Specified in Table 4.1 in sub clause 4.2.2.7.1 in [2].
TBCCH Equal to 1.9 s, i.e. the ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.2 1,28 Mcps Option | The cell re-selection delay shall be less than 8 s + TBCCH where TBCCH is the maximum time allowed to read BCCH data from GSM cell.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: Max(3*TmeasureNTDD , Tmeasure GSM +1DRX)+... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.3 7,68 Mcps Option | The cell re-selection delay shall be less than 26 s + TBCCH, where TBCCH is the maximum time allowed to read BCCH data in the GSM cell [21].
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
4 * TmeasureGSM + TBCCH
where:
T... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.3 Test purpose | This test verifies the UE meets the minimum requirement for the case where the UE camps on a TDD cell and reselects to a GSM cell. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4 Method of Test |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.