hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2 Minimum Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.1 3,84 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.7.2.1.
The normative reference for this requirement is TS 25.102 clause 7.8.1.1.
Table 6.7.2.1: Receive intermodulation characteristics (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modula... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.2 1,28 Mcps TDD Option | The BER shall not exceed 0.001 for the parameters specified in table 6.7.2.2.
The normative reference for this requirement is TS 25.102 clause 7.8.1.2.
Table 6.7.2.2: Receive intermodulation characteristics (1,28 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-105
dBm/1,28 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modul... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.3 7,68 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.7.2.3.
The normative reference for this requirement is TS 25.102 clause 7.8.1.3.
Table 6.7.2.3: Receive intermodulation characteristics (7,68 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-102
dBm/7.68 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modul... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.3 Test purpose | The test stresses the ability of the receiver to withstand two or more high level interference signals without undue degradation of its sensitivity due to the receiver's non-linear elements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and the unwanted signals to the UE antenna connector as shown in figure A.7.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback test mode and star... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4.2 Procedure | 1) Set the wanted and interfering signals as indicated in table 6.7.2.1 for the 3,84 Mcps TDD Option, table 6.7.2.2 for the 1,28 Mcps TDD Option and table 6.7.2.3 for the 7,68 Mcps TDD Option with positive offset with respect to the wanted signal.
2) Measure the BER of DCH received from the UE at the SS.
3) Set the int... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.1 3,84 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.1 for the 3,84 Mcps TDD Option.
Table 6.7.5.1: Test parameters Receive intermodulation characteristics (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
ÎorWanted Signal Level
-102
dBm/3,84 MHz
Iouw1(CW)
-4... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.2 1,28 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.2 for the 1,28 Mcps TDD Option.
Table 6.7.5.2: Test parameters Receive intermodulation characteristics (1,28 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-105
dBm/1,28 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean p... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.3 7,68 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.3 for the 7,68 Mcps TDD Option.
Table 6.7.5.3: Test parameters Receive intermodulation characteristics (7,68 Mcps TDD Option)
Parameter
Value
Unit
0
dB
ÎorWanted Signal Level
-102
dBm/3,84 MHz
Iouw1(CW)
-4... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8 Spurious Emissions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.1 Definition and applicability | The Spurious Emissions Power is the power of emissions generated or amplified in a receiver that appear at the UE antenna connector.
The requirements of this test are applicable for all UTRA UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2 Minimum Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.1 3,84 Mcps TDD Option | The power of any spurious emission shall not exceed:
Table 6.8.2.1: Receiver spurious emission requirements (3,84 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz – 1 GHz
-57 dBm
100 kHz
1 GHz – 1,9 GHz and
1,92 GHz – 2,01 GHz and
2,025 GHz – 2,11 GHz
-47 dBm
1 MHz
1,9 GHz – 1,92 GHz and
2,01 GHz –... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.2 1,28 Mcps TDD Option | The power of any spurious emission shall not exceed the maximum level specified in Table 6.8.2.2 and Table 6.8.2.2A.
Table 6.8.2.2: Receiver spurious emission requirements (1,28Mcps TDD Option)
Frequency Band
Measurement
Bandwidth
Maximum level
Note
30MHz f < 1GHz
100 kHz
-57 dBm
1GHz f 12.75 GHz
1 MHz
-47 dBm
Ta... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.3 7,68 Mcps TDD Option | The power of any spurious emission shall not exceed:
Table 6.8.2.3: Receiver spurious emission requirements (7,68 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz - 1 GHz
-57 dBm
100 kHz
1 GHz - 1.9 GHz and
1.92 GHz - 2.01 GHz and
2.025 GHz - 2.11 GHz
2.17 GHz - 2.57 GHz
-47 dBm
1 MHz
1.9 GHz - 1.9... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.3 Test purpose | The test purpose is to verify the UE's ability to limit interference caused by receiver spurious emissions to the own and the other systems. The test requirements are tighter than in clause 5.5.3 ((TX) Spurious Emissions) because the time of Receive–Only-Operation is generally much longer than RX-TX-Operation. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: 1 arbitrary frequency selected between low, mid and high range; see clause G.2.4.
1) Connect the measurement equipment to the UE antenna connector according to figure A.8.
2) RF parameters are setup according to table 6.8.4.1a for 3,84 Mcp... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4.2 Procedure | Measure the average power of spurious emissions by covering the frequency ranges of table 6.8.2.1 for the 3,84 Mcps TDD Option, table 6.8.2.2 for the 1,28 Mcps TDD Option and table 6.8.2.3 for the 7,68 Mcps TDD Option. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.1 3,84 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.1 for the 3,84 Mcps TDD Option.
Table 6.8.5.1: Receiver spurious emission test requirements (3,84 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz – 1 GHz
-57 dBm
100 kHz
1 GHz – 1,9 GHz and
1,92 GHz – 2,01 GHz and
2,025 GHz – 2,11 GHz
-47 dB... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.2 1,28 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.2 and table 6.8.5.2A for the 1,28 Mcps TDD Option.
Table 6.8.5.2: Receiver spurious emission requirements (1,28Mcps TDD Option)
Frequency Band
Measurement
Bandwidth
Maximum level
Note
30MHz f < 1GHz
100 kHz
-57 dBm
1GHz f 12.75 GHz
1 MHz
-47 dBm
Table 6.8.5... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.3 7,68 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.3 for the 7,68 Mcps TDD Option.
Table 6.8.5.3: Receiver spurious emission test requirements (7,68 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz - 1 GHz
-57 dBm
100 kHz
1 GHz - 1.9 GHz and
1.92 GHz - 2.01 GHz and
2.025 GHz - 2.11 GHz
2.17 G... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7 Performance Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.1 General | The performance requirements for the UE in this clause is specified for the measurement channels specified in annex C and the test environments specified in annex D.
All Block Error ratio (BLER) measurements in clause 7 shall be performed according to the general rules for statistical testing in Annex F.6. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.1.2 Definition of Additive White Gaussian Noise (AWGN) Interferer | The minimum bandwidth of the AWGN interferer shall be 1.5 times chip rate of the radio access mode. (e.g. 5.76 MHz for a chip rate of 3,84 Mcps). The flatness across this minimum bandwidth shall be less than 0.5 dB and the peak to average ratio at a probability of 0.001% shall exceed 10 dB. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2 Demodulation in static propagation conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1 Demodulation of DCH | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.1 Definition and applicability | The performance requirement of DCH in static propagation conditions is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The da... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.2.1.2.1a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.1.
Table 7.2.1.2.1a: DCH parameters in static propagation cond... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.2.1.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.2.
Table 7.2.1.2.2a: DCH parameters in static propagation conditions (1,28Mcps TDD Option)
Parameters
Unit
Test 1... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.2.1.2.3a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.3.
Table 7.2.1.2.3a: DCH parameters in static propagation cond... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal ,representing a static propagation channel for the wanted and for the co-channel signals fr... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, AWGN Generator and additional components to the UE antenna connector as shown in figure A.9.
2) A call is set up according to the Generic call setup procedure. The characteristic of the call ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.2.1.2.1a for the 3,84 Mcps TDD Option, table 7.2.1.2.2a for the 1,28 Mcps TDD Option and table 7.2.1.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.5.2 for the1.28 Mcps TDD Option
Table 7.2.1.5.2: Performance requirements in AWGN channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
3.9
10-2
2
2.7
10-1
3.0
10-2
3
3.1
10-1
3.5
10-2
4
4.9
10-1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3 Demodulation of DCH in multipath fading conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1 Multipath fading Case 1 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER). The BLER is specified for each individual data ratio of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data ratios, supported. The data-ratio-corresponding requireme... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.1.2.1a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.1.1.1.
Table 7.3.1.2.1a: DCH parameters in multipath Case 1 channel (3... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.1.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.1.1.2.
Table 7.3.1.2.2a: DCH parameters in a multipath Case 1 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
T... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.1.2.3a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.3b. This requirement is applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.1.1.3.
Table 7.3.1.2.3a: DCH parameters in multipath Case 1 channel (7,68... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal, representing a multipath propagation channel for the wanted and for the co-channel signals... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, , the fading simulator, the AWGN generator and additional components to the UE antenna connector as shown in figure A.10.
2) A call is set up according to the Generic call setup procedure. Th... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.3.1.2.1a for the 3,84 Mcps TDD Option, table 7.3.1.2.2a for the 1,28 Mcps TDD Option and table 7.3.1.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.5.2b for the1.28 Mcps TDD Option
Table 7.3.1.5.2b: Performance requirements in a multipath Case 1 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
23.0
10-2
2
16.4
10-1
23.5
10-2
3
17.2
10-1
24.5
10-2
4
16.2
10-1
22.0
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2 Multipath fading Case 2 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The data-rate-corresponding requirement... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.2.2.1a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.
Table 7.3.2.2.1a: DCH parameters in multipath Case 2 channel... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.2.2.2a: the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.2.
Table 7.3.2.2.2a: DCH parameters in multipath Case 2 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
Te... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.2.2.3a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.3.
Table 7.3.2.2.3a: DCH parameters in multipath Case 2 chann... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal, representing a multipath propagation channel for the wanted and for the co-channel signals... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, the fading simulator, the AWGN generator and additional components to the UE antenna connector as shown in figure A.10.
2) A call is set up according to the Generic call setup procedure. The ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.3.2.2.1a for the 3,84 Mcps TDD Option, table 7.3.2.2.2a for the 1,28 Mcps TDD Option and table 7.3.2.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.5.2b for the1.28 Mcps TDD Option
Table 7.3.2.5.2b: Performance requirements in multipath Case 2 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
14.2
10-2
2
10.4
10-1
14.5
10-2
3
10.9
10-1
15.0
10-2
4
12.0
10-1
15.6
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3 Multipath fading Case 3 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The data-rate-corresponding requirement... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.3.2.1a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.3.1.1.
Table 7.3.3.2.1a: DCH parameters in multipath Case 3 channel (... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.3.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.3.1.2.
Table 7.3.3.2.2a: DCH parameters in multipath Case 3 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
Tes... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.3.2.3a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.3.1.3.
Table 7.3.3.2.3a: DCH parameters in multipath Case 3 channel (... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal ,representing a multipath propagation channel for the wanted and for the co-channel signals... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, the fading simulator, the AWGN generator and additional components to the UE antenna connector as shown in figure A.10.
2) A call is set up according to the Generic call setup procedure. The ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.3.3.2.1a for the 3,84 Mcps TDD Option, table 7.3.3.2.2a for the 1,28 Mcps TDD Option and table 7.3.3.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.3.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.3.5.2b for the1.28 Mcps TDD Option
Table 7.3.3.5.2b: Performance requirements in multipath Case 3 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
12.3
10-2
2
9.6
10-1
12.3
10-2
14.9
10-3
3
10.0
10-1
11.8
10-2
13.3
10-3
4
10.5
10-1
11.8
10-2
13.... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.3.2.3b for the 7.68Mcps TDD Option.
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the ... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.4 Base station transmit diversity mode for 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.4.1 Demodulation of BCH in SCTD mode | This is not tested. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5 Power control in downlink | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.1 Definition and applicability | Power control in the uplink is the ability of the UE to converge to the required link quality set by the network while using minimum uplink power. The requirements of this test shall apply to the UTRA-TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2 Power control in downlink for 3,84 Mcps TDD option, constant BLER Target | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.1 Minimum requirements | For the parameters specified in table 7.5.2.1 the downlink averaged over one timeslot shall be below the specified value in table 7.5.2 more than 90% of the time. BLER shall be as shown in table 7.5.2.2 Downlink power control is ON during the test.
Table 7.5.2.1: Test parameters for downlink power control - constant B... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.2 Test purpose | To verify that the UE receiver is capable of converging to the required link quality set by the network while using as low power as possible. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.3 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.3.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect SS, multipath fading simulator and an AWGN source to the UE antenna connector as shown in figure A.10.
2) Set up a call according to the Generic call setup procedure.
3) RF parameters are set up acco... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.3.2 Procedure | 1) After the target quality on DTCH is met, BLER is measured. Simultaneously the downlink power ratio averaged over one slot is measured. This is repeated until adequate amount of measurements is done to reach the required confidence level.
2) The measured quality on DTCH (BLER) and the measured downlink power ratio v... |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.2.4 Test Requirements | a) The measured quality on DTCH does not exceed the values in table 7.5.2.2.
b) The downlink power ratio values, which are averaged over one slot, shall be below the values in table 7.5.2.2 more than 90 % of the time. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.3 Power control in downlink for 1,28 Mcps TDD option, constant BLER Target(Release 6 and earlier) | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.5.3.1 Definition and applicability | Power control in the downlink is the ability of the UE receiver to converge to required link quality set by the network while using as low power as possible in downlink. If a BLER target has been assigned to a DCCH (See clause C.3), then it has to be such that outer loop is based on DTCH and not on DCCH. The requiremen... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.