hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
9d41333a56d064c976d8032fae056f46 | 103 793 | 4.1 n100 | The operating band and channel arrangement specifications defined for band n100 in ETSI TS 138 101-1 [1], clause 5 shall apply. Only 5 MHz wide channel bandwidth shall be considered for band n100. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 4.2 n101 | The operating band and channel arrangement specifications defined for band n101 in ETSI TS 138 101-1 [1], clause 5 shall apply. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 9 |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5 Specifications for base stations | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.1 Output power | The specifications defined in ETSI TS 138 104 [2], clauses 6.2.1 and 6.2.4 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.2 Spurious emissions | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.2.0 General | The limits defined in ETSI TS 138 104 [2], Table 6.6.5.2.1-2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.2.1 n100 | In addition to the requirements defined in clause 5.2.0, for a base station transmitting in n100, the limits defined in ETSI TS 138 104 [2], Tables 6.6.5.2.3-1 and 6.6.5.2.3-13 shall apply to European frequency bands listed in Annex A. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.2.2 n101 | In addition to the requirements defined in clause 5.2.0, for a base station transmitting in n101, the limits defined in ETSI TS 138 104 [2], Tables 6.6.5.2.3-1 and 6.6.5.2.3-12 shall apply to European frequency bands listed in Annex A. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.2.3 Operating band unwanted emissions | For wide area base stations, the limits defined in ETSI TS 138 104 [2], Table 6.6.4.2.2.2-1 shall apply. For medium range base stations, the limits defined in ETSI TS 138 104 [2], Tables 6.6.4.2.3-1 and 6.6.4.2.3-2 shall apply. For local area base stations, the limits defined in ETSI TS 138 104 [2], Table 6.6.4.2.4-1 s... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.3 Reference sensitivity | The specifications defined in ETSI TS 138 104 [2], clause 7.2.2 for frequency bands n100 and n101 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.4 Receiver intermodulation | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.4.1 n100 | The specifications defined in ETSI TS 138 104 [2], clauses 7.7.2 and 7.7.3 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.4.2 n101 | The specifications defined in ETSI TS 138 104 [2], clause 7.7.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.5 In-band blocking | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.5.1 n100 | The specifications defined in ETSI TS 138 104 [2], clauses 7.4.2.2 and 7.4.2.5 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.5.2 n101 | The specifications defined in ETSI TS 138 104 [2], clause 7.4.2.2 shall apply. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 10 |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.6 Out-of-band blocking | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.6.1 n100 | The specifications defined in ETSI TS 138 104 [2], clause 7.5.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 5.6.2 n101 | The specifications defined in ETSI TS 138 104 [2], clauses 7.5.2 and 7.5.5 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6 Specifications for cab radio user equipment | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.0 General | This clause defines the specifications for cab radio user equipment, which fulfil the power class 1 category as specified in ETSI TS 138 101-1 [1], clause 6.2. If an external antenna is present the PEIRP shall not exceed 33 dBm. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.1 Output power | The specifications defined in ETSI TS 138 101-1 [1], clause 6.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.2 Out-of-band and spurious emissions | The specifications defined in ETSI TS 138 101-1 [1], clauses 6.1, 6.5.2 and 6.5.3 shall apply to European frequency bands listed in Annex A. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.3 NR ACLR | The specifications defined in ETSI TS 138 101-1 [1], clause 6.5.2.4.1 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.4 Reference sensitivity | The specifications defined in ETSI TS 138 101-1 [1], clause 7.3.2 for frequency band n100 and n101 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.5 Blocking requirements | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.5.0 General | The following Tables define the tolerable interfering signals that need to be taken into account for the cab radio user equipment. The frequency ranges for the interfering signals shall be considered edge-to-edge, including any guard band within the carrier as defined in the respective standard of the interfering signa... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.5.1 n100 | For n100, the blocking signals identified in Table 6.5.1-1 shall be considered. Table 6.5.1-1: n100 cab radio blocking characteristics Frequency range (edge to edge) Interfering signal type Power level for interfering signal Level of wanted signal Corresponding test case in clause 9.2.2 880 - 915 MHz 5 MHz LTE, accordi... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 6.5.2 n101 | For n101, the blocking signals identified in Table 6.5.2-1 shall be considered. Table 6.5.2-1: n101 cab radio blocking characteristics Frequency range (edge to edge) Interfering signal type Power level for interfering signal Level of wanted signal Corresponding test case in clause 9.2.2 1 805 - 1 880 MHz 5 MHz LTE, acc... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7 Specifications for terminals other than cab radios | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.0 General | This clause defines the specifications for terminals other than cab radios, which fulfil the power class 3 category as specified in ETSI TS 138 101-1 [1], clause 6.2. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.1 Output power | The specifications defined in ETSI TS 138 101-1 [1], clause 6.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.2 Out-of-band and spurious emissions | The specifications defined in ETSI TS 138 101-1 [1], clauses 6.1, 6.5.2 and 6.5.3 shall apply to European frequency bands listed in Annex A. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.3 NR ACLR | The specifications defined in ETSI TS 138 101-1 [1], clause 6.5.2.4.1 shall apply. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 12 |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.4 Reference sensitivity | The specifications defined in ETSI TS 138 101-1 [1], clause 7.3.2 for frequency bands n100 and n101 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 7.5 Blocking requirements | The specifications defined in ETSI TS 138 101-1 [1], clause 7.6 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8 Test cases for base stations | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.1 Transmitter | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.1.1 Output power | The test case defined in ETSI TS 138 141-1 [3], clause 6.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.1.2 Spurious emissions | The test cases defined in ETSI TS 138 141-1 [3], clause 6.6 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.2 Receiver | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.2.1 Reference sensitivity | The test case defined in ETSI TS 138 141-1 [3], clause 7.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.2.2 In-band selectivity and blocking | The test cases defined in ETSI TS 138 141-1 [3], clause 7.4 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.2.3 Out-of-band blocking | The test case defined in ETSI TS 138 141-1 [3], clause 7.5 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 8.2.4 Receiver intermodulation | The test case defined in ETSI TS 138 141-1 [3], clause 7.7 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9 Test cases for cab radio user equipment | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.0 General | This clause defines the test cases for cab radio user equipment, which fulfil the power class 1 category as specified in ETSI TS 138 101-1 [1], clause 6.2. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.1 Transmitter | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.1.1 Output power | The test cases defined in ETSI TS 138 521-1 [5], clause 6.2 shall apply. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 13 |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.1.2 NR ACLR | The test case defined in ETSI TS 138 521-1 [5], clause 6.5.2.4.1 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.1.3 Out-of-band and spurious emissions | The test cases defined in ETSI TS 138 521-1 [5], clauses 6.5.2 and 6.5.3 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2 Receiver | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.1 Reference sensitivity power level | The test case defined in ETSI TS 138 521-1 [5], clause 7.3 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2 Blocking | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.0 General Requirements | The test procedures specified in the present clause shall be carried out using the defined characteristics (in Tables 6.5.1-1 and 6.5.2-1) for testing RF blocking with FRMCS cab radio user equipment. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.1 Test purpose | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.2 Test method #1 | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.2.1 Test applicability | This test method applies to all FRMCS cab radio user equipment. It is used for testing RF blocking with interfering signals of type other than CW (see Tables 6.5.1-1 and 6.5.2-1). |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.2.2 Minimum conformance requirements | The throughput of the wanted signal shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in ETSI TS 138 521-1 [5], clauses A.2.2, A.2.3, A.3.2 and A.3.3 (with one sided dynamic OCNG Pattern OP.1 FDD/TDD for the DL signal as described in ETSI TS 138 521-1 [5], clause A.5) with par... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.2.3 Test description | 9.2.2.2.3.1 Initial conditions Initial conditions are a set of test configurations in which the cab radio UE needs to be tested in and the steps for the SS to take with the cab radio UE to reach the correct measurement state. The initial test configurations consist of environmental conditions based on NR operating band... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.2.4 Test requirement | The throughput measurement derived in test procedure shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in ETSI TS 138 521-1 [5], clauses A.2.2, A.2.3 and A.3.2 with parameters specified in Tables 9.2.2.2.2-1 and 9.2.2.2.3.1-1. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.3 Test method #2 | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.3.1 Test applicability | This test method applies to all FRMCS cab radio user equipment. It is used for testing RF blocking with interfering signals of type CW (see Table 6.5.1-1). |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.3.2 Minimum conformance requirements | The throughput of the wanted signal shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in ETSI TS 138 521-1 [5], clauses A.2.2, A.2.3, A.3.2 and A.3.3 (with one sided dynamic OCNG Pattern OP.1 FDD/TDD for the DL-signal as described in ETSI TS 138 521-1 [5], clauses A.5.1.1 and ... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.3.3 Test Description | 9.2.2.3.3.1 Initial Conditions Initial conditions are a set of test configurations in which the cab radio UE needs to be tested in and the steps for the SS to take with the cab radio UE to reach the correct measurement state. The initial test configurations consist of environmental conditions based on NR operating band... |
9d41333a56d064c976d8032fae056f46 | 103 793 | 9.2.2.3.4 Test Requirement | The throughput measurement derived in test procedure shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in ETSI TS 138 521-1 [5], clauses A.3.2 and A.3.3 with parameters specified in Tables 9.2.2.3.2-1 and 9.2.2.3.3.1-1. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 18 |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10 Test cases for terminals other than cab radios | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.0 General | This clause defines the test cases for terminals other than cab radios, which fulfil the power class 3 category as specified in ETSI TS 138 101-1 [1], clause 6.2. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.1 Transmitter | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.1.1 Output power | The test cases defined in ETSI TS 138 521-1 [5], clause 6.2 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.1.2 NR ACLR | The test case defined in ETSI TS 138 521-1 [5], clause 6.5.2.4.1 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.1.3 Out-of-band and spurious emissions | The test cases defined in ETSI TS 138 521-1 [5], clauses 6.5.2 and 6.5.3 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.2 Receiver | |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.2.1 Reference sensitivity power level | The test case defined in ETSI TS 138 521-1 [5], clause 7.3 shall apply. |
9d41333a56d064c976d8032fae056f46 | 103 793 | 10.2.2 Blocking | The test cases defined in ETSI TS 138 521-1 [5], clause 7.6 shall apply. ETSI ETSI TS 103 793 V1.1.1 (2025-11) 19 Annex A (normative): European mobile bands, excluding n100 and n101 Table A-1: List of European mobile bands, excluding n100 and n101 Protected system Frequency range for co-existence requirement GSM900 921... |
142241be1ea90643e055df0a41f4debe | 119 540 | 1 Scope | The present document defines standardization issues for Smart Contracts, as defined in Data Act [i.1], and based on Electronic Ledgers as defined by eIDAS2 [i.2]. It builds on existing and planned standardization and publicly available specifications. It presents a novel and as yet unpublished Chain of Trust, by addres... |
142241be1ea90643e055df0a41f4debe | 119 540 | 2 References | |
142241be1ea90643e055df0a41f4debe | 119 540 | 2.1 Normative references | Normative references are not applicable in the present document. |
142241be1ea90643e055df0a41f4debe | 119 540 | 2.2 Informative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks i... |
142241be1ea90643e055df0a41f4debe | 119 540 | 3 Definition of terms, symbols and abbreviations | |
142241be1ea90643e055df0a41f4debe | 119 540 | 3.1 Terms | For the purposes of the present document, the following terms apply: algorithm: set of rules and non-ambiguous procedures to solve a class of problems Chain of Trust: trust needs of legal or natural persons, as used in Regulation (EU) 2024/1183 [i.2], and of the relationships existing among them Deontic Logic: philosop... |
142241be1ea90643e055df0a41f4debe | 119 540 | 3.2 Symbols | Void. |
142241be1ea90643e055df0a41f4debe | 119 540 | 3.3 Abbreviations | For the purposes of the present document, the following abbreviations apply: AI Artificial Intelligence API Application Public Interface ARF Architecture and Reference Framework CA Certificate Authority DAG Directed Acyclic Graph dAPP distributed Application DID Decentralized Identity DLT Distributed Ledger Technology ... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.1 Essential Overview | The present clause presents an overview of all relevant European Union Regulations, Standards, Projects, and other activities involving Smart Contracts and Electronic Ledgers in a neutral and agnostic manner. For each of these activities, the present document proceeds as follows: • Essential Overview: Provide an extend... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2 Regulations | |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.1 Data Act | |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.1.1 Essential Overview | In addressing the definition of a Smart Contract, the following objectives can be derived directly from the definition in Regulation (EU) 2023/2854 [i.1] "a computer program used for the automated execution of an agreement or part thereof, using a sequence of electronic data records and ensuring their integrity and the... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.1.2 Terminology | Smart Contracts, Electronic Ledgers. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.1.3 Chain of Trust | Regulation (EU) 2023/2854 [i.1] is agnostic with respect to the Chain of Trust, and in particular with the production of Smart Contracts. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.2 eIDAS2 | |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.2.1 Essential Overview | The Electronic Identification, Authentication, and Trust Services Regulation (eIDAS) was first published in 2014 to provide a standardized framework across the European Union for electronic identification (eID), electronic signatures, and trust services. The aim was to enable secure and seamless digital transactions ac... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.2.2 Terminology | Electronic Ledgers. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.2.3 Chain of Trust | Regulation (EU) 2024/1183 [i.2], as per the publication date of the present document, is agnostic with respect to the Smart Contracts and the Chain of Trust. This can change in the forthcoming eIDAS2 Implementing Acts. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.3 GDPR | |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.3.1 Essential Overview | The General Data Protection Regulation (GDPR) [i.7] is a comprehensive legal framework established by the European Union to safeguard the personal data of individuals within the EU. It sets stringent rules for data privacy, ensuring that personal data is collected, processed, and stored with a high degree of transparen... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.3.2 Terminology | Not applicable. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.3.3 Chain of Trust | Regulation (EU) No 2016/679 [i.7] is agnostic with respect to Smart Contracts, Electronic Ledgers and the Chain of Trust. |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.4 UNCITRAL model law on automated contracting | |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.4.1 Essential Overview | The UNCITRAL Model Law [i.20] provides a legal framework to enable the use of automation in international contracts, including through the deployment of artificial intelligence techniques and Smart Contracts, as well as in machine-to-machine transactions. It is intended to complement and supplement existing laws on ele... |
142241be1ea90643e055df0a41f4debe | 119 540 | 4.2.4.2 Terminology | Smart Contracts. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.