hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.3.1.1 Test execution | The test procedure shall only be executed if ICCD Bulk Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing ICCD Bulk capability. Configurations are identified by index values. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.3.1.2 Initial conditions | • Device is at Device Address 42 and in Configured state. • ICCD Bulk Configuration selected. • ATR has been received on ETSI TS 102 221 [2] interface, and recorded. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.3.1.3 Test procedure | Step Direction Description RQ 1 T UICC Send PC_to_RDR_IccPowerOff 2 UICC T Return RDR_to_PC_SlotStatus (USB-ICC is virtually not present) RQ06_0102 3 T UICC Send PC_to_RDR_IccPowerOn 4 UICC T Return RDR_to_PC_DataBlock containing valid ATR Verify that this ATR is identical to the one recorded from ETSI TS 102 2... |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.4 EEM - Ethernet Emulation Model | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.4.1 Test case 1: EEM Echo Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.4.1.1 Test execution | The test procedure shall only be executed if EEM Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing EEM capability. Configurations are identified by index values. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.4.1.2 Initial conditions | • Device is at Device Address 42 and in Configured state. • EEM Configuration selected. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.4.1.3 Test procedure | Step Direction Description RQ 1 T UICC Send single EEM command packet with "Echo" 2 UICC T Return valid "Echo response" RQ06_0301 If any USB control transfer request returns "Request Error", this is considered as a failure of the UICC. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5 Mass-Storage | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.1 Test case 1: Device Type Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.1.1 Test execution | The test procedure shall only be executed if Mass Storage Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing Mass Storage capability. Configurations are identified by index values. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.1.2 Initial conditions | • Power Negotiation executed with power requested by the UICC (i.e. sufficient power to run the Mass Storage capability). • Device is at Device Address 42 and in Configured state. • MSC Configuration selected. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.1.3 Test procedure | Step Direction Description RQ 1 T UICC Send CBW containing SCSI "INQUIRY" command, as per SCSI Primary Command set of ANSI/INCITS 408-2005 [11]. 2 UICC T Return the CSW and SCSI "Standard INQUIRY Data", as per SCSI Primary Command set of ANSI/INCITS 408-2005 [11]. RQ06_0401 RQ06_0402 ETSI ETSI TS 102 922-2 V7.1.0 (... |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.2 Test case 2: Removable Media Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.2.1 Test execution | The test procedure shall only be executed if Mass Storage Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing Mass Storage capability. Configurations are identified by index values. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.2.2 Initial conditions | • Device connected (no Power Negotiation executed). • Device is at Device Address 42 and in Configured state. • MSC Configuration selected. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.2.3 Test procedure | Step Direction Description RQ 1 T UICC Send CBW containing SCSI "INQUIRY" command, as per SCSI Primary Command set of ANSI/INCITS 408-2005 [11]. 2 UICC T Return the CSW and SCSI "Standard INQUIRY Data", as per SCSI Primary Command set of ANSI/INCITS 408-2005 [11]. Check for Removable Medium Bit is set. RQ06_0401 RQ... |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.3 Test case 3: Insufficient Power Capabilities for Mass Storage Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.3.1 Test execution | The test procedure shall only be executed if Mass Storage Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing Mass Storage capability. Configurations are identified by index values. This test is based on the assumption that 10 mA is not eno... |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.3.2 Initial conditions | • Device connected (no Power Negotiation executed). • Device is at Device Address 42 and in Configured state. • MSC Configuration selected. ETSI ETSI TS 102 922-2 V7.1.0 (2025-10) 37 Release 7 |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.3.3 Test procedure | Step Direction Description RQ 1 T UICC Send Get Interface Power Request 2 UICC T Return Get Interface Power Request Response 3 T UICC Send Set Interface Power Request with a power of 10 mA 4 T UICC Send CBW containing SCSI "Test Unit Ready" command, as per SCSI Primary Command set of ANSI/INCITS 408-2005 [11] 5... |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.4 Test case 4: Stop Unit Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.4.1 Test execution | The test procedure shall only be executed if Mass Storage Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing Mass Storage capability. Configurations are identified by index values. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.4.2 Initial conditions | • Power Negotiation executed with power requested by the UICC (i.e. sufficient power to run the Mass Storage capability). • Device is at Device Address 42 and in Configured state. • MSC Configuration selected. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.4.3 Test procedure | Step Direction Description RQ 1 T UICC Send CBW containing SCSI "Start Stop Unit" command with the following parameter: - POWER CONDITIONS = 0 - LOEJ = 0 - START = 0 2 UICC T Return valid CSW with status 0 RQ06_0401 RQ05_0207 |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.5 Test case 5: MBR Test | |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.5.1 Test execution | The test procedure shall only be executed if Mass Storage Interface is present. The test procedure shall be performed for each available configuration (as declared in clause 4.3) containing Mass Storage capability. Configurations are identified by index values. ETSI ETSI TS 102 922-2 V7.1.0 (2025-10) 38 Release 7 |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.5.2 Initial conditions | • Power Negotiation executed with power requested by the UICC (i.e. sufficient power to run the Mass Storage capability). • Device is at Device Address 42 and in Configured state. • MSC Configuration selected. |
cc725a86775f5379efd6316472d76bc0 | 102 922-2 | 6.7.5.5.3 Test procedure | Step Direction Description RQ 1 T UICC Send CBW containing SCSI "Read Capacity" command 2 UICC T Return CSW with Status 0 and Read Capacity Data RQ06_0401 3 T UICC Send CBW containing SCSI "Read(10)" requesting first Sector of unprotected Memory 4 UICC T Return CSW with Status 0 and requested first Sector data ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 1 Scope | The present document covers the minimum characteristics which are considered necessary for the terminal in order to provide compliance to ETSI TS 102 600 [1]. The present document specifies the test cases for: • the characteristics of the Inter-Chip USB electrical interface between the USB UICC and the USB UICC-enabled... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 2 References | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 2.1 Normative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. • In the case of a reference... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 2.2 Informative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. • In the case of a reference... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.1 Terms | For the purposes of the present document, the terms given in ETSI TS 102 600 [1] and ETSI TS 102 221 [2] apply. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.2 Symbols | For the purposes of the present document, the symbols given in ETSI TS 102 600 [1] and ETSI TS 102 221 [2] apply. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 10 Release 7 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.3 Abbreviations | For the purposes of the present document, the abbreviations given in ETSI TS 102 600 [1], ETSI TS 102 221 [2] and the following apply: APDU Application Protocol Data Unit ATR Answer To Reset DUT Device Under Test EEM Ethernet Emulation Model FFS For Further Study IC Integrated Circuit ICC Integrated Circuit Card ICCD I... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.4 Formats | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.4.1 Format of the table of optional features | The columns in table 4.1 have the following meaning. Column Meaning Option The optional feature supported or not by the implementation. Status See clause 3.4.3, "Status and Notations". Support The support columns shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IE... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.4.2 Format of the applicability table | The applicability of every test in table 4.2 a) is formally expressed by the use of Boolean expression defined in the following clause. The columns in table 4.2 have the following meaning. Column Meaning Test case The "Test case" column gives a reference to the test case number(s) detailed in the present document and r... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 3.4.3 Status and Notations | The "Rel-x Terminal" columns show the status of the entries as follows: The following notations, defined in ISO/IEC 9646-7 [4], are used for the status column: M mandatory - the capability is required to be supported. O optional - the capability may be supported or not. N/A not applicable - in the given context, it is ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4 Test environment | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.1 Table of optional features | The supplier of the implementation shall state the support of possible options in table 4.1. See clause 3.4 for the format of table 4.1. Table 4.1: Options Item Option Status Support Mnemonic 1 Class B supported O O_ClassB 2 Resume Time Request supported O O_ResTimeReq 3 Remote Wake-up supported O O_RemWakeUp 4 ICCD Bu... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.2 Applicability table | Table 4.2 a) specifies the applicability of each test case to the device under test. See clause 3.4 for the format of table 4.2 a). Table 4.2 a): Applicability of tests Test case Description Release Rel-7 Terminal Support Basic Electrical Tests 6.3.1.1 Phase preceding Terminal power on Rel-7 M Activation Tests 6.4.1.1 ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.3 Information provided by the device supplier | Void. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 13 Release 7 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4 Test Equipment (TE) | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.0 Introduction | The test equipment shall provide a UICC simulator which is connected to the DUT during test procedure execution, unless otherwise specified. With respect to the Terminal, the UICC simulator shall act as a valid UICC according to ETSI TS 102 600 [1] and ETSI TS 102 221 [2], unless otherwise specified. In particular, dur... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.1 Measurement/setting uncertainties | Void. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.2 Default conditions for DUT operation | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.2.1 Temperature | The tests shall be run at a fully operational temperature (i.e. between -25 °C and +85 °C). |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.3 Minimum/maximum conditions for DUT operation | Void. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.4 Void | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.5 ATRs to be used by the UICC simulator | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.5.0 Introduction | For some particular test cases, the ATRs described below need to be specifically used. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 14 Release 7 4.4.5.1 ATR that indicates that UICC is USB capable and indicates support of classes B and C' Character Value Description TS '3B' Indicates direct convention T0 '97' TA1 and TD1 ar... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.5.2 Void | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.5.3 Void | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6 USB Descriptors to be used by the UICC simulator | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.0 Introduction | Within the descriptors, strings may be used to describe the descriptor and are denoted by i which is an index of a string description - set to 0 if no string. These are, if defined, to be included in the total length N of the descriptors. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.1 Single configuration, Single interface | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.1.0 Introduction | Descriptors supporting a single configuration containing a Control B transfer interface. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 15 Release 7 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.1.1 Device Descriptor (Single Configuration) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X1 idProduct Y1 bcdDevice Z1 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 1 The Product, Vendor ID and Device Release Number (bcdDevice) X1,Y1 and Z1 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.1.2 Configuration Descriptor (ICCD Control B) | ICCD Configuration Descriptor (Control B) bLength '09' wTotalLength N bNumInterfaces 1 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 ICCD Interface Descriptor (Control B) bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints 0 bInterfaceClass '0B' bInterfaceSub... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.2 Multiple configurations, Single interface | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.2.1 Device Descriptor (Multiple Configuration 1) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X2 idProduct Y2 bcdDevice Z2 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 2 The Product, Vendor ID and Device Release Number (bcdDevice) X2,Y2 and Z2 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.2.2 Configuration Descriptors (ICCD Control B and ICCD Bulk) | ICCD Configuration Descriptor (Control B) bLength '09' wTotalLength N bNumInterfaces 1 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 ICCD Interface Descriptor (Control B) bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints '00' bInterfaceClass '0B' bInterface... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.3 Multiple Configurations, Multiple interfaces | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.3.1 Device Descriptor (Multiple Configuration 2) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X3 idProduct Y3 bcdDevice Z3 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 2 The Product, Vendor ID and Device Release Number (bcdDevice) X3,Y3 and Z3 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.3.2 Configuration Descriptors (ICCD Control B, ICCD Bulk, EEM and MSC) | ICCD Configuration Descriptor (Control B) bLength '09' wTotalLength N bNumInterfaces 3 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 ICCD Interface Descriptor (Control B) bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints 0 bInterfaceClass '0B' bInterfaceSub... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.4 Multiple configurations, Single interface, Extended APDU | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.4.1 Device Descriptor (Multiple Configuration 3) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X4 idProduct Y4 bcdDevice Z4 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 2 The Product, Vendor ID and Device Release Number (bcdDevice) X4,Y4 and Z4 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.4.2 Configuration Descriptors (ICCD Control B and ICCD Bulk, Extended APDU) | ICCD Configuration Descriptor (Control B) bLength '09' wTotalLength N bNumInterfaces 1 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 ICCD Interface Descriptor (Control B) bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints '00' bInterfaceClass '0B' bInterface... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.5 Single Configuration, No ICCD interface support | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.5.1 Device Descriptor (Single Configuration) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X5 idProduct Y5 bcdDevice Z5 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 1 The Product, Vendor ID and Device Release Number (bcdDevice) X5,Y5 and Z5 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.5.2 Configuration Descriptor (EEM and MSC) | Configuration Descriptor (EEM and MSC) bLength '09' wTotalLength N bNumInterfaces 2 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 EEM Interface Descriptor bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints 2 bInterfaceClass '02' bInterfaceSubClass '0C' bInte... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.6 Multiple configurations, Alternative Single interface | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.6.1 Device Descriptor (Multiple Configuration 4) | bLength Check '12' bDescriptorType '01' bcdUSB '0200' bDeviceClass '00' bDeviceSubClass '00' bDeviceProtocol '00' bMaxPacketSize0 64 idVendor X6 idProduct Y6 bcdDevice Z6 iManufacturer i iProduct i iSerialNumber i bNumConfigurations 2 The Product, Vendor ID and Device Release Number (bcdDevice) X6,Y6 and Z6 with associ... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.4.6.6.2 Configuration Descriptors (ICCD Bulk and ICCD Control B) | Configuration Descriptor (ICCD Bulk Transfer) bLength '09' wTotalLength N bNumInterfaces 1 bConfigurationValue 1 iConfiguration i bmAttributes '80' bMaxPower 4 ICCD Interface Descriptor (Bulk Transfer) bLength '09' bDescriptorType '04' bInterfaceNumber 0 bAlternateSetting '00' bNumEndpoints '02' bInterfaceClass '0B' bI... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.5 Test execution | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.5.1 Parameter variations | Unless otherwise specified, all tests shall be carried out once for each voltage class available in the terminal in addition to the parameter variations specified individually for each test case. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 4.6 Pass criterion | A test shall only be considered as successful if the test procedure was carried out successfully under all parameter variations with the DUT respecting all conformance requirements referenced in the test procedure. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 28 Release 7 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5 Conformance Requirements | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.1 USB UICC system architecture | Reference: ETSI TS 102 600 [1], clause 4. RQ number Clause Description RQ01_0101 4.1 USB UICC-enabled terminals shall remain compliant with ETSI TS 102 221 [2]. RQ01_0201 4.2 The ETSI TS 102 221 [2] interface shall be activated when a terminal with only ETSI TS 102 221 [2] capability is connected to a USB UICC. RQ01_02... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.2 Physical characteristics | Reference: ETSI TS 102 600 [1], clause 5. RQ number Clause Description RQ02_0001 5 The physical characteristics of the USB UICC-Terminal interface are as defined in ETSI TS 102 221 [2] except for the specific provisions specified in the present document. RQ02_0101 5.1.1.1 A USB UICC-enabled terminal shall provide conta... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.3 Electrical characteristics | Reference: ETSI TS 102 600 [1], clause 6. RQ number Clause Description RQ03_0101 6.1 The operating conditions defined in ETSI TS 102 221 [2] apply to USB UICCs and USB UICC-enabled terminals, except when otherwise specified in the present document. RQ03_0102 6.1 The contacts C4 and C8 operate as specified in Inter-Chip... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.4 Initial communication establishment procedures | Reference: ETSI TS 102 600 [1], clause 7. RQ number Clause Description RQ04_0101 7.1 A USB UICC-enabled terminal shall support voltage class C' and may support voltage class B. RQ04_0102 7.1 The terminal shall initially select its lowest supported voltage class. RQ04_0103 7.1 The terminal shall power up the UICC with t... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.5 USB interface operational features | Reference: ETSI TS 102 600 [1], clause 8. RQ number Clause Description RQ05_0101 8.1 USB Full Speed, as defined in USB 2.0 [5], shall be supported on the USB UICC-enabled terminal. RQ05_0201 8.2 A USB UICC-enabled terminal shall support the Get Interface Power request as defined in ETSI TS 102 600 [1], tables 8.1 and 8... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.6 Protocol stacks for USB UICC applications | Reference: ETSI TS 102 600 [1], clause 9. RQ number Clause Description RQ06_0101 9.1 All USB UICC-enabled terminals shall support short APDU-level exchanges over Version B Control transfer with no Interrupt pipe, as defined in the Smart Card ICCD specification [9]. RQ06_0102 9.1 Applications relying on APDU communicati... |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.7 USB Descriptors of a USB UICC | Reference: ETSI TS 102 600 [1], annex A. RQ number Clause Description RQ07_0101 A.5.1 A Terminal compliant to the ETSI TS 102 600 [1] shall accept USB UICCs that indicate support of extended APDUs in dwFeatures and dwMaxCCIDMessageLength, even though ETSI TS 102 221 [2] currently only defines short APDUs. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 5.8 Assigned values for vendor specific USB requests | Reference: ETSI TS 102 600 [1], annex B. No requirement in this clause. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 33 Release 7 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6 Test cases | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.1 Void | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.2 Void | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3 Basic Electrical Tests | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3.1 Supply Voltage Value | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3.1.1 Test case 1: Phase preceding Terminal power on | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3.1.1.1 Test execution | The test procedure shall be executed once for each of following parameters: • There are no test case-specific parameters for this test case. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3.1.1.2 Initial conditions | • The Terminal shall be connected to an UICC simulator. • The contact C1 (VCC) of the UICC-Terminal interface shall be loaded with an impedance of 10 kΩ. • The other contacts (C2, C3, C4, C7, C8) shall be loaded with an impedance of 50 kΩ. |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.3.1.1.3 Test procedure | Step Direction Description RQ 1 T UICC The residual voltage on contacts C4 and C8 shall not exceed ±0,4 V referenced to GND. RQ02_0201 |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.4 Activation Tests | |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.4.1 Voltage-Activation | 6.4.1.1 Test case 1: Selection of voltage class C' as lowest supported voltage, no support of class B |
b2ebd9052bea1a749553916e67f136d5 | 102 922-1 | 6.4.1.1.1 Test execution | The test procedure shall only be executed if class B is not supported by the terminal. The test procedure shall be executed once for each of following parameters: • There are no test case-specific parameters for this test case. ETSI ETSI TS 102 922-1 V7.3.0 (2021-02) 34 Release 7 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.