hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3G Reference sensitivity for Tx Diversity | 7.3G.0 Minimum conformance requirements For UE supporting Tx diversity, the minimum requirements specified in Table 7.3.2.3-1a, 7.3.2.3-1b, 7.3.2.3-1d, 7.3.2.3-2 and Table 7.3.2.3-2a shall be met with Tx diversity configuration described in clause 6.2G.1.1. For Tx diversity, the parameter PUMAX is defined in clause 6.2... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3I Reference sensitivity for (e)RedCap | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3I.1 General | The reference sensitivity power level REFSENS is the minimum mean power applied to each one of the UE antenna ports for all UE categories, at which the throughput shall meet or exceed the requirements for the specified reference measurement channel. |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3I.2 Reference sensitivity power level for RedCap | 7.3I.2.1 Test purpose The test purpose is to verify the ability of the UE to receive data with a given average throughput for a specified reference measurement channel, under conditions of low signal level, ideal propagation and no added noise. 7.3I.2.2 Test applicability This test case applies to all types of NR UE re... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3I.3 Reference sensitivity power level for eRedCap | 7.3I.3.1 Test purpose The test purpose is to verify the ability of the UE to receive data with a given average throughput for a specified reference measurement channel, under conditions of low signal level, ideal propagation and no added noise. 7.3I.3.2 Test applicability This test case applies to all types of NR UE re... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3J Reference sensitivity for ATG | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3J.1 General | For ATG UE with multiple omni-directional antennas not indicating the capability antennaArrayType-r18, the reference sensitivity power level REFSENS is the minimum mean power per polarization at antenna connector, at which the throughput shall meet or exceed the requirements for the specified reference measurement chan... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.3J.2 Reference sensitivity power level for ATG | Editor’s note: This clause is incomplete. The following aspects are either missing or not yet determined: - MU/TT are FFS for ATG UEs with more than 2 transmit antenna connectors/ transceiver array boundary (TAB) connectors. - MU/TT already defined are based on preliminary analysis of single TE vendor. Values will be r... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4 Maximum input level | Editor’s note: The following aspects are either missing or not yet determined: - MU and TT for f>6GHz are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is available. 7.4.1 Test purpose Maximum input level tests the UE's ability to receive data wit... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A Maximum input level for CA | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.0 Minimum conformance requirements | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.0.1 Maximum input level for Intra-band contiguous CA | For intra-band contiguous carrier aggregation maximum input level is defined as the maximum mean power received at the UE antenna port, over the Transmission bandwidth configuration of each CC. 3GPP TS 38.521-1 version 19.2.0 Release 19 1862 ETSI TS 138 521-1 V19.2.0 (2025-11) ETSI The throughput shall be ≥ 95 % of the... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.0.2 Maximum input level for Intra-band non-contiguous CA | For intra-band non-contiguous carrier aggregation with one uplink carrier and two or more downlink sub-blocks, each larger than or equal to 5 MHz, the maximum input level requirements are defined with the uplink configuration in accordance with 7.3A.0.2.2-1. For this uplink configuration, the UE shall meet the requirem... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.0.3 Maximum input level for Inter-band CA | For inter-band carrier aggregation with one component carrier per operating band and the uplink assigned to one NR band, the maximum input level is defined with the uplink active on the band(s) other than the band whose downlink is being tested. For NR CA configurations including an operating band without uplink band o... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.1 Maximum input level for CA (2DL CA) | 7.4A.1.1 Test purpose The same test purpose as defined in 7.4.1. 7.4A.1.2 Test applicability This test case applies to all types of NR UE release 15 and forward that supports 2DL CA. 7.4A.1.3 Minimum conformance requirements The minimum conformance requirements are defined in clause 7.4A.0. 3GPP TS 38.521-1 version 19.... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.2 Maximum input level for CA (3DL CA) | 7.4A.2.1 Test purpose The same test purpose as defined in 7.4.1. 7.4A.2.2 Test applicability This test case applies to all types of NR UE release 15 and forward that supports 3DL CA. 7.4A.2.3 Minimum conformance requirements The minimum conformance requirements are defined in clause 7.4A.0. 7.4A.2.4 Test description 7.... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.3 Maximum input level for CA (4DL CA) | 7.4A.3.1 Test purpose The same test purpose as defined in 7.4.1. 7.4A.3.2 Test applicability This test case applies to all types of NR UE release 15 and forward that supports 4DL CA. 7.4A.3.3 Minimum conformance requirements The minimum conformance requirements are defined in clause 7.4A.0. 7.4A.3.4 Test description 7.... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4A.4 Maximum input level for CA (5DL CA) | Editor’s Note: - Test Configuration Table and test repetition and measurement configuration are TBD. - RefSens for 5DL CA is FFS 7.4A.4.1 Test purpose The same test purpose as defined in 7.4.1. 7.4A.4.2 Test applicability This test case applies to all types of NR UE release 15 and forward that supports 5DL CA. 7.4A.4.3... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4B Maximum input level for NR-DC | For inter-band NR-DC configurations, the maximum input level for the corresponding inter-band CA configuration as specified in clause 7.4A applies. Note: For NR-DC testing, replace CA by NR-DC, PCC by PCell, and SCC by PSCell in clause 7.4A. |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4D Maximum input level for UL MIMO | 7.4D.1 Test purpose Maximum input level tests the ability of UE that supports UL MIMO to receive data with a given average throughput for a specified reference measurement channel, under conditions of high signal level, ideal propagation and no added noise. A UE unable to meet the throughput requirement under these con... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4E Maximum input level for V2X | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4E.0 Minimum conformance requirements | 7.4E.0.1 General Maximum input level is defined as the maximum mean power received at the UE antenna port, at which the specified relative throughput shall meet or exceed the minimum requirements for the specified reference measurement channel. When UE is configured for NR V2X reception non-concurrent with NR uplink tr... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4E.1 Maximum input level for V2X / non-concurrent operation | 7.4E.1.1 Test purpose Maximum input level tests the UE's ability to receive data with a given average throughput for a specified reference measurement channel, under conditions of high signal level, ideal propagation and no added noise. A UE unable to meet the throughput requirement under these conditions will decrease... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4E.2 Maximum input level for V2X / concurrent operation | Editor’s Note: This clause is incomplete. The following aspects are not yet determined: - The TP analysis, connection diagram and test requirement are FFS. 7.4E.2.1 Test purpose Same test purpose as specified in 7.4E.1.1 for concurrent operation. 7.4E.2.2 Test applicability No test case details are specified for inter-... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4F Maximum input level for shared spectrum channel access | Editor’s note: - MU and TT for >6GHz (band n96) are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is available. 7.4F.1 Test purpose Maximum input level tests the UE's ability to receive data with a given average throughput for a specified referenc... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4G Maximum input level for Tx Diversity | 7.4G.1 Maximum input level for Tx Diversity for UE supporting 4Tx 7.4G.1.1 Test purpose Same as the test purpose given in clause 7.4.1. 7.4G.1.2 Test applicability This test case applies to all types of NR Power Class 1.5 UE release 18 and forward that support 4Tx Tx diversity. 7.4G.1.3 Minimum conformance requirements... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.4J Maximum input level for ATG | Editor’s note: This clause is incomplete. The following aspects are either missing or not yet determined: - MU/TT are FFS for ATG UEs with more than 2 transmit antenna connectors/ transceiver array boundary (TAB) connectors. - MU/TT already defined are based on preliminary analysis of single TE vendor. Values will be r... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5 Adjacent channel selectivity | Editor’s note: The following aspects are either missing or not yet determined: 3GPP TS 38.521-1 version 19.2.0 Release 19 1891 ETSI TS 138 521-1 V19.2.0 (2025-11) ETSI - MU and TT for f>6GHz are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is ava... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A Adjacent channel selectivity for CA | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.0 Minimum conformance requirements | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.0.1 Adjacent channel selectivity for Intra-band contiguous CA | For intra-band contiguous carrier aggregation the downlink SCC(s) shall be configured at nominal channel spacing to the PCC. The UE shall fulfil the minimum requirement specified in Table 7.5A.0.1-1 and 7.5A.0.1-1a for an adjacent channel interferer on either side of the aggregated downlink signal at a specified freque... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.0.2 Adjacent channel selectivity Intra-band non-contiguous CA | For intra-band non-contiguous carrier aggregation with FDL_high < 2700 MHz and FUL_high < 2700 MHz with one uplink carrier and two or more downlink sub-blocks, each larger than or equal to 5 MHz, the adjacent channel selectivity requirements are defined with the uplink configuration in accordance with Table 7.3A.0.2.2-... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.0.3 Adjacent channel selectivity Inter-band CA | For inter-band carrier aggregation with one component carrier per operating band and the uplink assigned to one NR band, the adjacent channel requirements are defined with the uplink active on the band(s) other than the band whose downlink is being tested. For NR CA configurations including an operating band without up... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.1 Adjacent channel selectivity for CA (2DL CA) | 7.5A.1.1 Test Purpose Adjacent channel selectivity for 2DL CA verifies the receiver's ability to receive a wanted 2DL carrier aggregated at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. 7.5A.1.2 Test Applicabil... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.2 Adjacent channel selectivity for CA (3DL CA) | 7.5A.2.1 Test Purpose Adjacent channel selectivity for 3DL CA verifies the receiver's ability to receive a wanted 3DL carrier aggregated at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. 7.5A.2.2 Test Applicabil... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.3 Adjacent channel selectivity for CA (4DL CA) | Editor’s note: - part content of Table 7.5A.3.4.2-1 is FFS. 7.5A.3.1 Test Purpose Adjacent channel selectivity for 4DL CA verifies the receiver's ability to receive a wanted 4DL carrier aggregated at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5A.4 Adjacent channel selectivity for CA (5DL CA) | Editor’s Note: - Test Configuration Table and test repetition and measurement configuration are TBD. - RefSens for 5DL CA is FFS 7.5A.4.1 Test Purpose Adjacent channel selectivity for 5DL CA verifies the receiver's ability to receive a wanted 5DL carrier aggregated at its assigned channel frequency in the presence of a... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5B Adjacent channel selectivity for NR-DC | For inter-band NR-DC configurations, the adjacent channel selectivity for the corresponding inter-band CA configuration as specified in clause 7.5A applies. Note: For NR-DC testing, replace CA by NR-DC, PCC by PCell, and SCC by PSCell in clause 7.5A. |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5D Adjacent channel selectivity for UL MIMO | 7.5D.1 Test purpose Adjacent channel selectivity (ACS) is a measure of a receiver's ability to receive an NR signal at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the receive filter attenu... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5E Adjacent channel selectivity for V2X | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5E.0 Minimum conformance requirements | 7.5E.0.1 General Adjacent channel selectivity (ACS) is a measure of a receiver's ability to receive an NR signal at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the receive filter attenuati... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5E.1 Adjacent channel selectivity for V2X / non-concurrent operation | 7.5E.1.1 Test purpose Adjacent channel selectivity (ACS) is a measure of a receiver's ability to receive an NR signal at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the receive filter atte... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5E.2 Adjacent channel selectivity for V2X / concurrent operation | Editor’s Note: This clause is incomplete for configurations with reference sensitivity exception. The following aspects are not yet determined: - The test configurations in 7.3E.3 are FFS. 7.5E.2.1 Test purpose Same test purpose as specified in 7.5E.1.1 for concurrent operation. 7.5E.2.2 Test applicability This test ca... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5F Adjacent channel selectivity | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5F.1 Adjacent channel selectivity for shared spectrum channel access | Editor’s note: - MU and TT for >6GHz (band n96) are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is available 7.5F.1.1 Test purpose Adjacent channel selectivity (ACS) is a measure of a receiver's ability to receive an NR signal at its assigned ch... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5G Adjacent channel selectivity for Tx Diversity | 7.5G.0 General The requirements of adjacent channel selectivity for 2Tx Tx Diversity are tested in clause 7.5. The requirements of adjacent channel selectivity for 4Tx Tx Diversity are tested in clause 7.5G.1. 7.5G.1 Adjacent channel selectivity for Tx Diversity for UE supporting 4Tx 7.5G.1.1 Test purpose Same as the t... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.5J Adjacent channel selectivity for ATG | Editor’s note: This clause is incomplete. The following aspects are either missing or not yet determined: - MU are FFS for ATG UEs with more than 2 transmit antenna connectors/ transceiver array boundary (TAB) connectors. - MU already defined are based on preliminary analysis of single TE vendor. Values will be revisit... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6 Blocking characteristics | The blocking characteristic is a measure of the receiver’s ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6.1 General | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6.2 In-band blocking | Editor’s note: The following aspects are either missing or not yet determined: - The test is incomplete for NR Band n105 - Testability, MU and TT are pending for NR Band n105. - MU and TT for f>6GHz are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendor... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6.3 Out-of-band blocking | Editor’s note: The following aspects are either missing or not yet determined: - MU and TT for f>6GHz are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is available. 7.6.3.1 Test Purpose Out-of-band band blocking is defined for an unwanted CW inte... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6.4 Narrow band blocking | Editor’s note: The following aspects are either missing or not yet determined: - MU and TT for f>6GHz are working assumption based on analysis of single TE vendor. Values will be revisited once analysis from other TE vendors is available. 7.6.4.1 Test Purpose Verifies a receiver's ability to receive a NR signal at its ... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.1 General | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2 Inband blocking for CA | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.0 Minimum requirements | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.0.1 In-band blocking for Intra-band contiguous CA | For intra-band contiguous carrier aggregation the downlink SCC(s) shall be configured at nominal channel spacing to the PCC. The UE shall fulfil the minimum requirement specified in Table 7.6A.2.0.1-1 and 7.6A.2.0.1-1a for an adjacent channel interferer on either side of the aggregated downlink signal at a specified fr... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.0.2 In-band blocking for Intra-band non-contiguous CA | For intra-band non-contiguous carrier aggregation with one uplink carrier and two or more downlink sub-blocks, each larger than or equal to 5 MHz, the in-band blocking requirements are defined with the uplink configuration in accordance with Table 7.3A.0.3.2-1. For this uplink configuration, the UE shall meet the requi... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.0.3 In-band blocking for Inter-band CA | For inter-band carrier aggregation with one component carrier per operating band and the uplink assigned to one NR band, the in-band blocking requirements are defined with the uplink active on the band(s) other than the band whose downlink is being tested. The UE shall meet the requirements specified in subclause 7.6.2... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.1 In-band blocking for CA (2DL CA) | 7.6A.2.1.1 Test purpose Inband blocking is defined for an unwanted interfering signal falling into the range from 15 MHz below to 15 MHz above the UE receive band, with FDL_high < 2700 MHz and FUL_high < 2700 MHz, or into an immediately adjacent frequency range up 3* BWChannel_CA below or above the UE receive band, wit... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.2 In-band Blocking for CA (3DL CA) | 7.6A.2.2.1 Test purpose Same test purpose as in clause 7.6A.2.1. 7.6A.2.2.2 Test applicability This test applies to all types of NR UE release 15 and forward that support 3DL CA. 7.6A.2.2.3 Minimum conformance requirements Minimum requirements are defined in clause 7.6A.2.0. 7.6A.2.2.4 Test description 7.6A.2.2.4.1 Ini... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.3 In-band Blocking for CA (4DL CA) | 7.6A.2.3.1 Test purpose Same test purpose as in clause 7.6A.2.1. 7.6A.2.3.2 Test applicability This test applies to all types of NR UE release 15 and forward that support 4DL CA. 7.6A.2.3.3 Minimum conformance requirements Minimum requirements are defined in clause 7.6A.2.0. 7.6A.2.3.4 Test description 7.6A.2.3.4.1 Ini... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.2.4 In-band Blocking for CA (5DL CA) | Editor’s Note: This test is incomplete. The following aspects are not yet determined: - Test configuration table and Test repetition table are FFS. - RefSens test case for 5DL CA is FFS. 7.6A.2.4.1 Test purpose Same test purpose as in clause 7.6A.2.1. 7.6A.2.4.2 Test applicability This test applies to all types of NR U... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3 Out-of-band blocking for CA | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.0 Minimum conformance requirements | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.0.1 Out-of-band blocking for Intra-band contiguous CA | For intra-band contiguous carrier aggregation the downlink SCC(s) shall be configured at nominal channel spacing to the PCC. For FDD, the PCC shall be configured closest to the uplink band. All downlink carriers shall be active throughout the test. The UE shall fulfil the minimum requirement in presence of an interferi... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.0.2 Out-of-band blocking for Intra-band non-contiguous CA | For intra-band non-contiguous carrier aggregation with one uplink carrier and two or more downlink sub-blocks, the out-of-band blocking requirements are defined with the uplink configuration in accordance with table 7.3A.0.2.3-1. For this uplink configuration, the UE shall meet the requirements for each sub-block as sp... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.0.3 Out-of-band blocking for Inter-band CA | For inter-band carrier aggregation with one component carrier per operating band and the uplink assigned to one NR band, the out-of-band blocking requirements are defined with the uplink active on the band(s) other than the band whose downlink is being tested. The UE shall meet the requirements specified in subclause 7... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.1 Out-of-band blocking for CA (2DL CA) | 7.6A.3.1.1 Test purpose Out-of-band band blocking for CA is defined for an unwanted CW interfering signal falling more than 15 MHz or 3*BWChannel_CA below or above the UE receive band, at which a given average throughput shall meet or exceed the requirement for the specified measurement channels. For the first 15 MHz o... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.2 Out-of-band blocking for CA (3DL CA) | 7.6A.3.2.1 Test purpose Out-of-band band blocking for CA is defined for an unwanted CW interfering signal falling more than 15 MHz or 3*BWChannel_CA below or above the UE receive band, at which a given average throughput shall meet or exceed the requirement for the specified measurement channels. For the first 15 MHz o... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.3 Out-of-band blocking for CA (4DL CA) | 7.6A.3.3.1 Test purpose Out-of-band band blocking for CA is defined for an unwanted CW interfering signal falling more than 15 MHz or 3*BWChannel_CA below or above the UE receive band, at which a given average throughput shall meet or exceed the requirement for the specified measurement channels. For the first 15 MHz o... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.3.4 Out-of-band blocking for CA (5DL CA) | Editor’s Note: This test is incomplete. The following aspects are not yet determined: - Test repetition and measurement configuration are FFS. 3GPP TS 38.521-1 version 19.2.0 Release 19 2024 ETSI TS 138 521-1 V19.2.0 (2025-11) ETSI 7.6A.3.4.1 Test purpose Out-of-band band blocking for CA is defined for an unwanted CW i... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4 Narrow band blocking for CA | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.0 Minimum conformance requirements | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.0.1 Narrow band blocking for Intra-band contiguous CA | For intra-band contiguous carrier aggregation, the downlink SCC(s) shall be configured at nominal channel spacing to the PCC. For FDD, the PCC shall be configured closest to the uplink band. All downlink carriers shall be active throughout the test. The uplink output power shall be set as specified in Table 7.6A.4.0.1-... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.0.2 Narrow band blocking for Intra-band non-contiguous CA | For intra-band non-contiguous carrier aggregation with FDL_low < 2700 MHz and FUL_low < 2700 MHz with one uplink carrier and two or more downlink sub-blocks, the narrow band blocking requirements are defined with the uplink configuration in accordance with Table 7.3A.0.2.2-1. For this uplink configuration, the UE shall... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.0.3 Narrow band blocking for Inter-band CA | For inter-band carrier aggregation with one component carrier per operating band and the uplink assigned to one NR band, the narrow band blocking requirements are defined with the uplink active on the band(s) other than the band whose downlink is being tested. The UE shall meet the requirements specified in subclause 7... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.1 Narrow band blocking for CA (2DL CA) | 7.6A.4.1.1 Test purpose Verifies a receiver's ability to receive an NR signal at its assigned CA channel frequencies in the presence of an unwanted narrow band CW interferer at a frequency, which is less than the nominal channel spacing. The lack of narrow-band blocking ability will decrease the coverage area when othe... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.2 Narrow band blocking for CA (3DL CA) | 7.6A.4.2.1 Test purpose Verifies a receiver's ability to receive an NR signal at its assigned CA channel frequencies in the presence of an unwanted narrow band CW interferer at a frequency, which is less than the nominal channel spacing. The lack of narrow-band blocking ability will decrease the coverage area when othe... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.3 Narrow band blocking for CA (4DL CA) | 7.6A.4.3.1 Test purpose Verifies a receiver's ability to receive an NR signal at its assigned CA channel frequencies in the presence of an unwanted narrow band CW interferer at a frequency, which is less than the nominal channel spacing. The lack of narrow-band blocking ability will decrease the coverage area when othe... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6A.4.4 Narrow band blocking for CA (5DL CA) | Editor’s Note: This clause is incomplete. The following aspects are either missing or not yet determined: - RefSens test case for 5DL CA is FFS - Out-of-band blocking test case is FFS 7.6A.4.4.1 Test purpose Verifies a receiver's ability to receive an NR signal at its assigned CA channel frequencies in the presence of ... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6B Blocking characteristics for NR-DC | For inter-band NR-DC configurations, the blocking characteristics for the corresponding inter-band CA configuration as specified in clause 7.6A applies. Note: For NR-DC testing, replace CA by NR-DC, PCC by PCell, and SCC by PSCell in clause 7.6A. 3GPP TS 38.521-1 version 19.2.0 Release 19 2042 ETSI TS 138 521-1 V19.2.0... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6C Blocking characteristics for SUL | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6C.1 General | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6C.2 In-band blocking for SUL | 7.6C.2.1 Test purpose Same test purpose as in clause 7.6.2.1. 7.6C.2.2 Test applicability This test applies to all types of NR UE release 15 and forward that support SUL operating on the SUL bands. 7.6C.2.3 Minimum conformance requirements For SUL operation, the in-band blocking requirement for downlink bands specified... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6C.3 Out-of-band blocking for SUL | 7.6C.3.1 Test Purpose Same test purpose as in clause 7.6.3.1. 7.6C.3.2 Test applicability This test applies to all types of NR UE release 15 and forward that support SUL operating on the SUL bands. 7.6C.3.3 Minimum conformance requirements For SUL operation, the out-of-band blocking requirement for downlink bands speci... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6D.1 General | The blocking characteristic for UL MIMO is a measure of the receiver's ability of an UE that support UL MIMO to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted inp... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6D.2 In-band blocking for UL MIMO | 7.6D.2.1 Test purpose In-band blocking for UL MIMO is defined for an unwanted interfering signal falling into the range from 15MHz below to 15MHz above the receive band of an UE that support UL MIMO, with FDL_high < 2700 MHz and FUL_high < 2700 MHz, or into the range from 3CBW below to 3CBW above the receive band of an... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6D.3 Out-of-band blocking for UL MIMO | 7.6D.3.1 Test purpose Out-of-band blocking for UL MIMO is defined for an unwanted CW interfering signal falling more than 15 MHz below or above the receive band of an UE that support UL MIMO, with FDL_high < 2700 MHz and FUL_high < 2700 MHz, or falling more than 3CBW below or above the receive band of an UE that suppor... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6D.4 Narrow band blocking for UL MIMO | 7.6D.4.1 Test purpose Narrow band blocking for UL MIMO is defined for a receiver's ability of an UE that supports UL MIMO to receive a NR signal at its assigned channel frequency in the presence of an unwanted narrow band CW interferer at a frequency, which is less than the nominal channel spacing, at which a given ave... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E Blocking characteristics for V2X | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.1 General | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.2 In-band blocking for V2X | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.2.0 Minimum conformance requirements | 7.6E.2.0.1 General When UE is configured for NR V2X reception non-concurrent with NR uplink transmissions for NR V2X operating bands specified in Table 5.2E.1-1, the throughput of the wanted signal shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in Annex A.7.2 with parameter... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.2.1 In-band blocking for V2X / non-concurrent operation | 7.6E.2.1.1 Test Purpose In-band blocking is defined for an unwanted interfering signal falling into the range from 30MHz below to 30MHz above the V2X band, at which the relative throughput shall meet or exceed the requirement for the specified measurement channels. The lack of in-band blocking ability will decrease the... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.2.2 In-band blocking for V2X / concurrent operation | 7.6E.2.2.1 Test Purpose Same test purpose as specified in 7.6.2.1 and 7.6E.2.1.1 for concurrent operation. 7.6E.2.2.2 Test Applicability No test case details are specified for inter-band concurrent operation. The In-band blocking requirements for V2X / concurrent operation apply and are tested in clauses 7.6.2 for NR d... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.3 Out-of-band blocking for V2X | |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.3.0 Minimum conformance requirements | 7.6E.3.0.1 General For NR V2X bands out-of-band band blocking is defined for an unwanted CW interfering signal falling outside a frequency range 30 MHz below or above the UE receive band. When UE is configured for NR V2X reception non- concurrent with NR uplink transmissions for NR V2X operating bands specified in Tabl... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.3.1 Out-of-band blocking for V2X / non-concurrent operation | 7.6E.3.1.1 Test Purpose Out-of-band blocking for V2X is defined for an unwanted CW interfering signal falling more than 30 MHz below or above the V2X band, at which a given average throughput shall meet or exceed the requirement for the specified measurement channels in aggregated signals. For the first 30 MHz below or... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6E.3.2 Out-of-band blocking for V2X / concurrent operation | 7.6E.3.2.1 Test Purpose Same test purpose as specified in 7.6.3.1 and 7.6E.3.1.1 for concurrent operation. 7.6E.3.2.2 Test Applicability No test case details are specified for inter-band concurrent operation. The Out-of-band blocking requirements for V2X / concurrent operation apply and are tested in clauses 7.6.3 for ... |
47427c363b8cb3a33a525cec081286b5 | 138 521-1 | 7.6F.1 General | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.