input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "搬送中継基板・I/O中継基板取付け",
"WorkItems": [],
"WorkPoints": [
"ﾏｽｷﾝｸﾞ右下に合わせること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "天井ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側",
"右側",
"左側"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "架台内ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. にCABLE CABLE を追加し固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾘｱ側",
"TAR_K313SO2_K313",
" 黄色ﾏｰｷﾝｸﾞを束線の白ｲﾝｼｭﾛｯｸに合わせる",
"TRAY.SRCABLE TRAY.SRを指示通りに引き回す",
"Ex.TRRR③TRAY.SRから指示通りにEx.TRRRまで引き回す",
"Ex.TRFR③TRAY.SRから指示通りにEx.TRFRまで引き回す",
"TAF_K313SO1_K313",
"TRAY.SFCABLE TRAY.SRを指示通りに引き回す",
"R4204/6･R4704/6",
"R4200/2･R4700/2",
"FT11",
"FT11",
"仕様により追加配線が変わります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(200mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入準備【OP:ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様】",
"WorkItems": [
"1. にCABLE CABLE CABLE を追加し固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾘｱ側",
" 黄色ﾏｰｷﾝｸﾞを束線の白ｲﾝｼｭﾛｯｸに合わせる",
"UP2_K311",
"M9_K323 TP_K323に合わせる",
"UP4_K311",
"B1226/7R･R4213/4/5R",
"B1115RB1243R",
"B1726/7R･R4712/3/5R",
"M629R",
"FT11",
"B11~15PR4093/4R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾈｸﾀ保護ｷｬｯﾌﾟ",
"Size": "",
"ToolOther": "FM-3319",
"WorkName": "束線投入準備",
"WorkItems": [
"1. 束線 を図のように展開し､投入準備する",
"2. ㉖を1A03/04、CRTK301コネクタに取付ける",
"3. ㉗にて束線を覆う"
],
"WorkPoints": [
"1A03 他",
"R4200/2 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3319",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "本体ﾊｰﾈｽ保護ｼﾞｸﾞ(NPM-GH用)",
"Size": "",
"ToolOther": "FM-6098",
"WorkName": "束線投入準備",
"WorkItems": [
"1. 束線 を図のように展開し､投入準備する",
"2. ㉖を1A03/04、CRTK301コネクタに取付ける",
"3. ㉗にて束線を覆う"
],
"WorkPoints": [
"1A03 他",
"R4200/2 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6098",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線投入",
"WorkItems": [
"◆1. ﾘｱ側より束線 を投入し中央板A･B･Cの穴よりﾌﾛﾝﾄ側ｹｰﾌﾞﾙを配線する"
],
"WorkPoints": [
"ｺﾈｸﾀやｹｰﾌﾞﾙを架台に引っ掛けないように注意すること",
"非常停止ｽｲｯﾁの端子を曲げないように注意すること",
"二人作業",
"1A03 他",
"R4200/2 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定①(中央)",
"WorkItems": [
"1. 中央部のｹｰﾌﾞﾙを引き回し架台に固定する"
],
"WorkPoints": [
"束線がﾌﾞﾗｹｯﾄの下になるように全体を押し下げて固定する",
"ﾌｧﾝ･束配線をこの穴から外に出す",
"ﾌｧﾝ配線",
"上の穴に差込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定②(右側)",
"WorkItems": [
"1. 右側束線を架台に引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"R4093R 他",
"2A13 他",
"1A04 他",
"B1237TP 他",
"R4132R 他",
"連結BKT",
"穴より上側へ",
"開口A",
"開口A内側",
"中継ﾌﾞﾗｹｯﾄへｺﾈｸﾀを挿入する",
"CART.R2P1",
"CART.R2MP",
"非常停止を先に通す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR",
"検査表①:2.R側確認1"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定②(右側)",
"WorkItems": [
"1. 右側束線を架台に引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"R4093R 他",
"2A13 他",
"1A04 他",
"B1237TP 他",
"R4132R 他",
"連結BKT",
"穴より上側へ",
"開口A",
"開口A内側",
"中継ﾌﾞﾗｹｯﾄへｺﾈｸﾀを挿入する",
"CART.R2P1",
"CART.R2MP",
"非常停止を先に通す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR",
"検査表①:2.R側確認1",
"WETE-G002-D05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却ﾌｧﾝｹｰﾌﾞﾙ固定・接続",
"WorkItems": [
"1. G112Pをﾌﾞﾗｹｯﾄに取付け､FANｺﾈｸﾀを接続する"
],
"WorkPoints": [
"G112P",
"G112R",
"余長をここで丸める"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"REAR",
"ｲﾝｼｭﾛｯｸ(100mm)",
"検査表①:2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定③(右側)",
"WorkItems": [
"1. 右側束線を架台に引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SIO基板)",
"WorkItems": [
"★1. SIO基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"DU-P",
"AIR",
"VL",
"TM1",
"TM2",
"FIO",
"RIO",
"EXR",
"OPL",
"EXL",
"OPR",
"UP1",
"UP2",
"AF",
"DU-S",
"AR",
"BF",
"BR",
"流れ方向によって接続するｺﾈｸﾀが異なるので注意すること",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"UP3",
"UP4",
"OP",
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時のみ接続する",
"FANF"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ﾏｰｷﾝｸﾞﾀｲ確認箇所",
"検査表①:6.Power Unit:確認",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SAFETY基板)",
"WorkItems": [
"★1. SAFETY基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CV5",
"EGF",
"HC",
"CV6",
"EGR",
"TBR",
"CAR",
"CAF",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CBR",
"CBF",
"TBF",
"TAR",
"TAF",
"SO2",
"SO1",
"F側ﾄﾚｲ仕様時接続",
"R側ﾄﾚｲ仕様時接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:6.Power Unit:確認",
"検査表②:3.ｺﾈｸﾀ接続確認",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SAFETY基板)",
"WorkItems": [
"★1. SAFETY基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CV5",
"EGF",
"HC",
"CV6",
"EGR",
"TBR",
"CAR",
"CAF",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CBR",
"CBF",
"TBF",
"TAR",
"TAF",
"SO2",
"SO1",
"F側ﾄﾚｲ仕様時接続",
"R側ﾄﾚｲ仕様時接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:6.Power Unit:確認",
"検査表②:3.ｺﾈｸﾀ接続確認",
"WETE-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "追加24V電源ｹｰﾌﾞﾙ・FANF配線引き回し",
"WorkItems": [
"1. 追加24V電源ｹｰﾌﾞﾙと束線のｹｰﾌﾞﾙを引き回し固定･接続する"
],
"WorkPoints": [
"CBF24VRA11CBR24VRA11",
"CAPWR",
"CBR24VRA11",
"CBF24VRA11",
"FANF",
"1_T113"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(150mm)",
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"検査表①:6.Power Unit:確認",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台下冷却ﾌｧﾝｹｰﾌﾞﾙ固定・接続",
"WorkItems": [
"2. G111Rを接続する",
"1. G111Pをﾌﾞﾗｹｯﾄに取付け､配線を固定する"
],
"WorkPoints": [
"G111R",
"G111P",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"検査表①:2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ中継ﾌﾞﾗｹｯﾄｺﾈｸﾀ接続",
"WorkItems": [
"1. 中継ﾌﾞﾗｹｯﾄにｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CAR24VR",
"CAF24VR",
"MCFR",
"MCRR",
"TP2R",
"TP1R",
"Ex.CAFR",
"Ex.CARR",
"1G103R",
"1G104R",
"1G111R",
"CAPWR",
"Ex.TRRR",
"Ex.TRFR",
"LC(Slave)",
"LC(Master)",
"F側ﾄﾚｲ仕様時接続",
"R側ﾄﾚｲ仕様時接続",
"前後荷重ﾁｪｯｶｰ有りの場合:P2001RをLC(Master)に接続 P2002RをLC(Slave)に接続",
"前側のみ荷重ﾁｪｯｶｰ有りの場合:P2001RをLC(Master)に接続",
"後側のみ荷重ﾁｪｯｶｰ有りの場合:P2002RをLC(Master)に接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:6.Power Unit:確認",
"検査表②:3.ｺﾈｸﾀ接続確認",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ中継ﾌﾞﾗｹｯﾄｺﾈｸﾀ接続",
"WorkItems": [
"1. 中継ﾌﾞﾗｹｯﾄにｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CAR24VR",
"CAF24VR",
"MCFR",
"MCRR",
"TP2R",
"TP1R",
"Ex.CAFR",
"Ex.CARR",
"1G103R",
"1G104R",
"1G111R",
"CAPWR",
"Ex.TRRR",
"Ex.TRFR",
"LC(Slave)",
"LC(Master)",
"F側ﾄﾚｲ仕様時接続",
"R側ﾄﾚｲ仕様時接続",
"前後荷重ﾁｪｯｶｰ有りの場合:P2001RをLC(Master)に接続 P2002RをLC(Slave)に接続",
"前側のみ荷重ﾁｪｯｶｰ有りの場合:P2001RをLC(Master)に接続",
"後側のみ荷重ﾁｪｯｶｰ有りの場合:P2002RをLC(Master)に接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:6.Power Unit:確認",
"検査表②:3.ｺﾈｸﾀ接続確認",
"WETE-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "連結信号ﾌﾞﾗｹｯﾄ取付け(右側)",
"WorkItems": [
"2. 連結ﾌﾞﾗｹｯﾄをBOLT WASHER で取付ける",
"1. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ﾒｲﾝｴｱｰONﾊﾞﾙﾌﾞ接続",
"WorkItems": [
"1. ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｺﾈｸﾀを で接続する"
],
"WorkPoints": [
"R301",
"ﾎﾞﾙﾄ",
"ﾊﾟｯｷﾝ",
"ﾊﾟｯｷﾝ取付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰONﾊﾞﾙﾌﾞ接続",
"WorkItems": [
"1. ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｺﾈｸﾀを で接続する"
],
"WorkPoints": [
"R301",
"ﾎﾞﾙﾄ",
"ﾊﾟｯｷﾝ",
"ﾊﾟｯｷﾝ取付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾞﾛｰ切替ﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [
"1. MANIFOLD をBOLT WASHER で取付ける",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"R4132",
"R4032"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表MANIFOLD :2.R側確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｰ切替ﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [
"1. MANIFOLD をBOLT WASHER で取付ける",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"R4132",
"R4032"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表MANIFOLD :2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ取付け・接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. ｺﾈｸﾀ･配管を接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"B0235",
"B0116",
"配管を接続",
"矢印方向に当付け取付けのこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ取付け・接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. ｺﾈｸﾀ･配管を接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"B0235",
"B0116",
"配管を接続",
"矢印方向に当付け取付けのこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定④(左側)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"1243P 他",
"*** K324 他",
"連結BRK, B1237P 他",
"*** K322 他",
"この穴から外に出す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑤(左側)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"3A13",
"中継ﾌﾞﾗｹｯﾄへｺﾈｸﾀを挿入する",
"CART.R1P",
"CART.R1MP",
"抜け穴より配線を上げない",
"B1115R 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"検査表①:2.R側確認1"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑤(左側)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを引き回し固定する",
"2. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"3A13",
"中継ﾌﾞﾗｹｯﾄへｺﾈｸﾀを挿入する",
"CART.R1P",
"CART.R1MP",
"抜け穴より配線を上げない",
"B1115R 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"検査表①:2.R側確認1",
"WETE-G002-D05"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑥(左側)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを引き回し固定する"
],
"WorkPoints": [
"B1237P 他",
"TRAY.PR",
"R4204/6 他",
"連結BKT 他",
"ﾄﾚｲ仕様時のみ作業実施のこと",
"B1047TP 他",
"B1047TP 他は架台上には上げないこの辺りに置いておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "I/O中継基板接続",
"WorkItems": [
"★1. I/O中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"DB",
"LPA",
"FB1",
"I O",
"SW3",
"BL",
"SW1",
"SW2",
"CLA",
"CG",
"FA2",
"FA1",
"FA3",
"FB2",
"CLB",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CRB"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:7.ｺﾈｸﾀ中継基板確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送中継基板接続",
"WorkItems": [
"★1. 搬送中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"OSR",
"OSP",
"TM",
"TP",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"M9"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:7.ｺﾈｸﾀ中継基板確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "連結信号ﾌﾞﾗｹｯﾄ取付け(左側)",
"WorkItems": [
"2. 連結ﾌﾞﾗｹｯﾄをBOLT WASHER で取付ける",
"1. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"■3. FG端子をSCREW で固定する"
],
"WorkPoints": [
"FGTR1",
"8㎜",
"26㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :4.ﾈｼﾞ締めﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"■3. FG端子をSCREW で固定する"
],
"WorkPoints": [
"FGTR1",
"8㎜",
"26㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :4.ﾈｼﾞ締めﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"■3. FG端子をSCREW で固定する"
],
"WorkPoints": [
"FGTR1",
"8㎜",
"26㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :4.ﾈｼﾞ締めﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け・接続、FG線固【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. 電源･信号ｹｰﾌﾞﾙを接続する",
"■3. FG端子をSCREW で固定する"
],
"WorkPoints": [
"TRAY.PR",
"TRAY.SR",
"FGTR1",
"8㎜",
"26㎜",
"傾き無き事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :3.ｺﾈｸﾀ接続確認",
"検査表 :4.ﾈｼﾞ締めﾄﾙｸ確認",
"WETE-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "3.2N･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"3. をBOLT WASHER で取付ける",
"2. をBOLT WASHER で取付ける"
],
"WorkPoints": [
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞ",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ取付け",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"3. をBOLT WASHER で取付ける",
"2. をBOLT WASHER で取付ける",
"1. をBOLT WASHER で取付ける",
"3. をBOLT WASHER で取付ける",
"2. をBOLT WASHER で取付ける"
],
"WorkPoints": [
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること",
"同じﾎﾞﾙﾄを使用しているので､ﾄﾙｸに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "15cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続する",
"2. 配線を固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K503/4は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:5.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続する",
"2. 配線を固定する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K503/4は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:5.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰAC・DCｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. ｺﾈｸﾀ･ｱｰｽ線を接続する",
"2. 配線を固定する"
],
"WorkPoints": [
"E1K504",
"E1K503",
"CN3K503",
"CN3K504",
"1AK503",
"1BK503",
"CNP1",
"P1AK514",
"CNP2",
"1AK504",
"CNP1",
"CNP2",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"CN3K503/4は上下均等に取付けﾈｼﾞを締めこんでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:5.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰFG端子固定",
"WorkItems": [
"■1. 電源ｹｰﾌﾞﾙのFG端子をSCREW で固定する",
"2. 配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SCREW :5.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "3.0N･m",
"WorkName": "各種ﾚｷﾞｭﾚｰﾀ部取付け",
"WorkItems": [
"1. をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｰ切替ﾊﾞﾙﾌﾞ・ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部配管接続",
"WorkItems": [
"1. ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部の配管を接続し､配管を固定する"
],
"WorkPoints": [
"配管折れに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "各種ﾚｷﾞｭﾚｰﾀ部配管接続",
"WorkItems": [
"1. ﾚｷﾞｭﾚｰﾀ部の配管を接続する"
],
"WorkPoints": [
"303F",
"303R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ取付け・配線接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. 電源ｹｰﾌﾞﾙを引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"赤色を上側にして接続する",
"右側2ヵ所はｽﾍﾟｰｻｰに嵌め込む",
"PUMP"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ取付け・配線接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. 電源ｹｰﾌﾞﾙを引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"赤色を上側にして接続する",
"右側2ヵ所はｽﾍﾟｰｻｰに嵌め込む",
"PUMP"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表 :2.R側確認2",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ・24V追加電源配線固定",
"WorkItems": [
"1. 真空ﾎﾟﾝﾌﾟ･追加24V電源の配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. 真空ﾎﾟﾝﾌﾟ部の配管を固定し接続する"
],
"WorkPoints": [
"架台の内側に固定する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管接続",
"WorkItems": [
"1. をBOLT WASHER で取付ける",
"2. 真空ﾎﾟﾝﾌﾟ部の配管を固定し接続する"
],
"WorkPoints": [
"架台の内側に固定する",
"702R",
"701R",
"702L",
"701L",
"真空ﾎﾟﾝﾌﾟに配管を接続する",
"401R",
"配管接続後㉘で固定し矢印方向に押し込みカバー取付け面より配管が出無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "3.0N･m",
"WorkName": "右側台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. をSCREW で取付け､ｺﾈｸﾀ･配管を接続する"
],
"WorkPoints": [
"215R",
"216R",
"JST表示が上側で取付ける",
"215/6Rの配管は固定しない"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. をSCREW で取付け､ｺﾈｸﾀ･配管を接続する"
],
"WorkPoints": [
"215R",
"216R",
"JST表示が上側で取付ける",
"215/6Rの配管は固定しない"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "3.0N･m",
"WorkName": "左側台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. をSCREW で取付け､ｺﾈｸﾀ･配管を接続し固定する"
],
"WorkPoints": [
"JST表示が上側で取付ける",
" の配管は固定しない"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側台車中継ﾌﾞﾗｹｯﾄ取付け・接続",
"WorkItems": [
"1. をSCREW で取付け､ｺﾈｸﾀ･配管を接続し固定する"
],
"WorkPoints": [
"JST表示が上側で取付ける",
" の配管は固定しない"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ配管接続",
"WorkItems": [
"1. ｶｯﾀｰﾊﾞﾙﾌﾞの配管を接続･固定する"
],
"WorkPoints": [
"205R",
"204Lも一緒に固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"REAR"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ配管接続",
"WorkItems": [
"1. 台車駆動ﾊﾞﾙﾌﾞに配管を接続する"
],
"WorkPoints": [
"215R",
"216R",
"215L",
"216L",
"30連/60連仕様",
"17連/34連+ﾄﾚｲ仕様",
"215R",
"216R",
"215R",
"216R",
"215L",
"216L",
"215/6L",
"221R",
"221L",
"505R",
"17連/34連+17連/34連仕様17連/34連+17連/34連切替仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ｼﾞｮｲﾝﾄ・ﾄﾚｲ用配管引き回し",
"WorkItems": [
"1. 中継ｼﾞｮｲﾝﾄを引き回し固定する",
"2. ﾄﾚｲ用配管を引き回し接続する"
],
"WorkPoints": [
"ﾄﾚｲ仕様時の未接続配管も固定する",
"504Rを下へ",
"215/6L",
"ﾄﾚｲ仕様が無い時は固定のみ実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ｼﾞｮｲﾝﾄ・ﾄﾚｲ用配管引き回し",
"WorkItems": [
"1. 中継ｼﾞｮｲﾝﾄを引き回し固定する",
"2. ﾄﾚｲ用配管を引き回し接続する"
],
"WorkPoints": [
"ﾄﾚｲ仕様時の未接続配管も固定する",
"504Rを下へ",
"215/6L",
"ﾄﾚｲ仕様が無い時は固定のみ実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ接続【交換台車切替ﾕﾆｯﾄ仕様】",
"WorkItems": [
"1. COVER をBOLT WASHER で取付ける",
"2. 台車駆動ﾊﾞﾙﾌﾞにｺﾈｸﾀを接続する"
],
"WorkPoints": [
"配線の挟み込みに注意する事",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"R4206",
"R4204",
"R4706",
"R4704"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表COVER :2.R側確認1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ接続【交換台車切替ﾕﾆｯﾄ仕様】",
"WorkItems": [
"1. COVER をBOLT WASHER で取付ける",
"2. 台車駆動ﾊﾞﾙﾌﾞにｺﾈｸﾀを接続する"
],
"WorkPoints": [
"配線の挟み込みに注意する事",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"R4206",
"R4204",
"R4706",
"R4704"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表COVER :2.R側確認1",
"WETE-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D05",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押さえ治具",
"Size": "",
"ToolOther": "FM-2888",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け①",
"WorkItems": [
"1. ㉗を取付け用ボルトで架台に固定する"
],
"WorkPoints": [
"取付け用ﾎﾞﾙﾄ",
"押し当て用ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2888",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け①",
"WorkItems": [
"1. ㉗を取付け用ボルトで架台に固定する"
],
"WorkPoints": [
"取付け用ﾎﾞﾙﾄ",
"押し当て用ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "2.4N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け①",
"WorkItems": [
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 2.4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け①",
"WorkItems": [
"3. LMｶﾞｲﾄﾞの仮締めしてあるﾎﾞﾙﾄを本締めする"
],
"WorkPoints": [
"仮締めﾎﾞﾙﾄ",
"本締め後㉗を取り外す"
],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押さえ治具",
"Size": "",
"ToolOther": "FM-2888",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け②",
"WorkItems": [
"1. 残りのLMｶﾞｲﾄﾞを仮締めしてあるﾎﾞﾙﾄも同様に本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2888",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け②",
"WorkItems": [
"1. 残りのLMｶﾞｲﾄﾞを仮締めしてあるﾎﾞﾙﾄも同様に本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "2.4N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け②",
"WorkItems": [
"1. 残りのLMｶﾞｲﾄﾞを仮締めしてあるﾎﾞﾙﾄも同様に本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け②",
"WorkItems": [
"1. 残りのLMｶﾞｲﾄﾞを仮締めしてあるﾎﾞﾙﾄも同様に本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け②",
"WorkItems": [
"2. LMｶﾞｲﾄﾞと当て面に隙間が無いことを確認する"
],
"WorkPoints": [
"0.03㎜が入らないこと",
"隙間確認後､ﾘｱ作業者と入れ替わり増し締め確認を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:2.Y軸ﾘﾆｱｶﾞｲﾄﾞの真直度",
"WETE-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ置き台",
"Size": "",
"ToolOther": "FM-4596",
"WorkName": "Y軸LMｶﾞｲﾄﾞ真直度測定",
"WorkItems": [
"◆1. 架台側面に㉖を取付けその上に㉗を置く",
"3. ｽﾗｲﾀﾞｰを可動させ両端の値が0になるようにｽﾄﾚｰﾄｴｯｼﾞ位置を調整する"
],
"WorkPoints": [
"㉗をPINに押し当てる",
"㉗をPINに押し当てる",
"搭載時二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"◆作業者安全作業",
"WETE-G002-C02"
]
} | {
"QualityItem": "真直度確認",
"ToolManageNo": "FM-4596",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽﾄﾚｰﾄｴｯｼﾞ",
"Size": "2m",
"ToolOther": "10μm以下",
"WorkName": "Y軸LMｶﾞｲﾄﾞ真直度測定",
"WorkItems": [
"◆1. 架台側面に㉖を取付けその上に㉗を置く",
"3. ｽﾗｲﾀﾞｰを可動させ両端の値が0になるようにｽﾄﾚｰﾄｴｯｼﾞ位置を調整する"
],
"WorkPoints": [
"㉗をPINに押し当てる",
"㉗をPINに押し当てる",
"搭載時二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"◆作業者安全作業",
"WETE-G002-C02"
]
} | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "0.03㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C02",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ真直度測定",
"WorkItems": [
"2. 両端のリニアスライダーに㉙㉚を取付け ストレートエッジにセッティングする"
],
"WorkPoints": [
"1. ﾌﾛﾝﾄ側のﾀﾞｲﾔﾙｹﾞｰｼﾞを0にｾｯﾄする",
"2. ｽﾗｲﾀﾞｰを中央位置付近 A 迄可動させ値を確認",
"3. 0になるようにｽﾄﾚｰﾄｴｯｼﾞ位置調整",
"4. 初期位置に戻す",
"5. 3で0調整した A の位置にﾘｱ側のﾀﾞｲﾔﾙｹﾞｰｼﾞを移動し0にｾｯﾄする",
"6. ｽﾗｲﾀﾞｰをﾘｱ側に可動させ値を確認",
"7. 0になるようにｽﾄﾚｰﾄｴｯｼﾞ位置調整 (4で初期位置に戻したﾀﾞｲﾔﾙｹﾞｰｼﾞの値が 変わらないように注意すること)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"REAR",
"FRONT",
"FRONT",
"◆作業者安全作業",
"WETE-G002-C02"
]
} | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.03㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ平行度測定",
"WorkItems": [
"1. リニアスライダーに㉖を付属ボルトにて取付ける",
"2. ﾚｰﾙにﾀﾞｲﾔﾙｹﾞｰｼﾞをｾｯﾃｨﾝｸﾞする"
],
"WorkPoints": [
"基準側",
"従動側",
"フレームとスライダーの隙間に㉖を入れていく",
"基準側ｽﾗｲﾀﾞｰ側面に治具をしっかり当てること",
"従動側はﾎﾞﾙﾄを入れてﾌﾘｰにしておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ﾘﾆｱ平行出しｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6031",
"WorkName": "Y軸LMｶﾞｲﾄﾞ平行度測定",
"WorkItems": [
"1. リニアスライダーに㉖を付属ボルトにて取付ける",
"2. ﾚｰﾙにﾀﾞｲﾔﾙｹﾞｰｼﾞをｾｯﾃｨﾝｸﾞする",
"3. 検査書に基づきﾘﾆｱｶﾞｲﾄﾞの平行度を測定し結果を検査書に記入する",
"4. ㉘㉙を外し㉖を取外す"
],
"WorkPoints": [
"基準側",
"従動側",
"フレームとスライダーの隙間に㉖を入れていく",
"基準側ｽﾗｲﾀﾞｰ側面に治具をしっかり当てること",
"従動側はﾎﾞﾙﾄを入れてﾌﾘｰにしておく",
"1. ﾌﾛﾝﾄ側のﾀﾞｲﾔﾙｹﾞｰｼﾞを0にｾｯﾄする",
"2. ㉖をを中央位置付近 A 迄可動させ値を確認",
"3. 値を覚えておく",
"4. 初期位置に戻す",
"5. A の位置にリア側の㉖を移動し、3で記憶した値にセットする",
"6. ㉖をリア側に可動させ値を確認",
"規格値:0.05㎜以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"検査表①:2.Y軸ﾘﾆｱｶﾞｲﾄﾞの真直度",
"FRONT",
"WETE-G002-C02"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "FM-6031",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付け面余白ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. LMガイド取付け面余白に㉖を薄く伸ばしながら塗布する"
],
"WorkPoints": [
"青色のところに塗布する",
"青色のところに塗布する",
"FRONT",
"REAR"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り塗布出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞｼﾘｱﾙNo.確認",
"WorkItems": [
"1. LMｶﾞｲﾄﾞのｼﾘｱﾙNoを確認し､検査書に記入する"
],
"WorkPoints": [
"FRONT"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.Y軸ﾘﾆｱｶﾞｲﾄﾞのｼﾘｱﾙNo.確認",
"WETE-G002-C02"
]
} | {
"QualityItem": "製造番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸仮取付け①(FRONT-右側)",
"WorkItems": [
"1. 架台の切り欠け位置にｽﾗｲﾀﾞｰを合わせ取付け面及び基準面の清掃を行う",
"2. ｸﾞﾘｰｽﾆｯﾌﾟﾙの方向を内側に向ける"
],
"WorkPoints": [
"REAR",
"ﾌﾛﾝﾄ側",
"ﾘｱ側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの方向になっている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "X軸仮取付け②(FRONT-右側)",
"WorkItems": [
"◆1. をｽﾗｲﾄﾞさせながら載せる",
"3. を数回揺さぶって取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを合わせ 基準(ﾍﾞｱ)側へ押し当てる",
"4. をﾌﾛﾝﾄ側作業者が仮締め完了するまで押し当てておく",
"5. ﾌﾛﾝﾄ側作業者の仮締め完了後､4点仮締めをする"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側作業者",
"FRONT",
"ﾘｱ側作業者にもｾﾝﾀｰ確認してもらう",
"ﾎﾞﾙﾄのｾﾝﾀｰ確認後に締める",
"SD-EJM2FB1-279にて本締結実施"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "X軸仮取付け(REAR-右側)",
"WorkItems": [
"◆1. をｽﾗｲﾄﾞさせながら載せる",
"3. を数回揺さぶってもらい取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを確認し 基準(ﾍﾞｱ)側へ押し当ててもらう",
"4. ﾌﾛﾝﾄ側作業者に押し当ててもらっている状態で4点仮締めをする"
],
"WorkPoints": [
"ﾘｱ側作業者",
"REAR",
"ﾎﾞﾙﾄのｾﾝﾀｰ確認後に締める",
"SD-EJM2FB1-278にて本締結実施"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ仮取付け",
"WorkItems": [
"1. 架台左側に をBOLT で仮取付けする",
"2. 架台右側に をBOLT で仮取付けする"
],
"WorkPoints": [
"SD-EJM2FB1-284にて本締結実施",
"SD-EJM2FB1-081にて本締結実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取付け",
"WorkItems": [
"1. X軸駆動部に計測ﾍｯﾄﾞ治具を搭載する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取付け",
"WorkItems": [
"1. X軸駆動部に計測ﾍｯﾄﾞ治具を搭載する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰWindows7",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "XYﾁｪｯｶｰ準備",
"WorkItems": [
"1. 電源ｹｰﾌﾞﾙを接続する",
"2. ﾊﾟｿｺﾝの電源をONする",
"3. ﾊﾟｿｺﾝを立ち上げる",
"4. CounterDisplayを起動する"
],
"WorkPoints": [
"ﾀﾞﾌﾞﾙｸﾘｯｸ",
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"fajapanと入力",
"Ctrl + Alt + Del を押す",
"ﾕｰｻﾞｰ名,ﾊﾟｽﾜｰﾄﾞを入力"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾗｲﾄﾞする"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰWindows7",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "XY直角度計測ﾍｯﾄﾞ(FRONT)⇔XYﾁｪｯｶｰ接続",
"WorkItems": [
"3. ﾌﾛﾝﾄ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙと信号ｹｰﾌﾞﾙを接続する",
"1. ｺﾝﾄﾛｰﾗｰ電源がOFFになっているかを確認する",
"2. 信号ｹｰﾌﾞﾙを取出す",
"4. ｺﾝﾄﾛｰﾗｰ電源をONにする"
],
"WorkPoints": [
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"ﾌﾛﾝﾄ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ",
"信号ｹｰﾌﾞﾙ",
"溝と突起を合わせ差込み矢印方向に回転させる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰWindows7",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "XY直角度計測ﾍｯﾄﾞ(REAR)⇔XYﾁｪｯｶｰ接続",
"WorkItems": [
"1. ｺﾝﾄﾛｰﾗｰ電源をOFFにする",
"3. ﾘｱ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙと信号ｹｰﾌﾞﾙを接続する",
"2. ﾌﾛﾝﾄ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙを外す",
"4. ｺﾝﾄﾛｰﾗｰ電源をONにする"
],
"WorkPoints": [
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"信号ｹｰﾌﾞﾙ",
"ﾘｱ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ",
"溝と突起を合わせ差込み矢印方向に回転させる",
"ﾌﾛﾝﾄ計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ",
"矢印方向に回転させて溝と突起を合わせ外す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取外し",
"WorkItems": [
"1. 駆動部に仕込んであるﾎﾞﾙﾄを緩める(4ヶ所)",
"2. X軸駆動部から計測ﾍｯﾄﾞ治具を取外す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外しが出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ本取付け(REAR-右側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ本取付け(FRONT-右側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(4)仮取付け・ｶﾊﾞｰ取付け",
"WorkItems": [
"2. 架台への取付け面に砥石をかけ、㉗で洗浄する"
],
"WorkPoints": [
"底面",
":架台への取付け面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"▲特殊作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "Yﾌﾚｰﾑ(4)仮取付け・ｶﾊﾞｰ取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄとﾘｱのXﾋﾞｰﾑをﾘｱ側まで移動する",
"◆4. 3完成品をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付けする",
"▲3. Y-FRAME(4) にCOVER をBOLT で取付ける"
],
"WorkPoints": [
"設備内側",
"㉚を塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"接着剤塗布 米粒:各1",
"▲特殊作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "Yﾌﾚｰﾑ(4)仮取付け・ｶﾊﾞｰ取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄとﾘｱのXﾋﾞｰﾑをﾘｱ側まで移動する",
"◆4. 3完成品をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付けする",
"▲3. Y-FRAME(4) にCOVER をBOLT で取付ける"
],
"WorkPoints": [
"設備内側",
"㉚を塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"接着剤塗布 米粒:各1",
"▲特殊作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(4)仮取付け・ｶﾊﾞｰ取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄとﾘｱのXﾋﾞｰﾑをﾘｱ側まで移動する",
"◆4. 3完成品をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付けする",
"2. 架台への取付け面に砥石をかけ、㉗で洗浄する",
"▲3. Y-FRAME(4) にCOVER をBOLT で取付ける"
],
"WorkPoints": [
"設備内側",
"設備外側",
"底面",
"㉚を塗布する",
":架台への取付け面",
"SD-EJM2FB1-281にて本締結実施"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"接着剤塗布 米粒:各1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ・Yﾌﾚｰﾑ(4)本取付け",
"WorkItems": [
"2. 架台に取付ける4本を締め付ける",
"4. Yﾌﾚｰﾑを本取付けする"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰを下側に押さえ付けて締結のこと"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾄｯﾊﾟｰ・Yﾌﾚｰﾑ(4)本取付け",
"WorkItems": [
"4. Yﾌﾚｰﾑを本取付けする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.