input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差測定1",
"WorkItems": [
"1. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『偏差測定』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑを押し【0(ｾﾞﾛ)】付近に移動する",
"4. 3の位置にて『ﾃﾞｰﾀ取込』をｸﾘｯｸする(PCの『Enterｷｰ』でも可)"
],
"WorkPoints": [],
"Tolks": [],
"Insp... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差測定2",
"WorkItems": [
"1. Xﾋﾞｰﾑを100㎜づつ移動させ､都度『ﾃﾞｰﾀ取込』をｸﾘｯｸする",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"移動誤差は±10㎜以内にする事",
"100㎜~1000㎜まで計10回取り込む"
],
"Tolks... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_偏差設定",
"WorkItems": [
"1. 『偏差設定』をｸﾘｯｸする",
"2. 『F側SET』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰ(ﾘｱXﾋﾞｰﾑを押す)に当てる"
],
"WorkPoints": [
"Y軸①: -66.4㎜ ~ -66.0㎜ / Y軸②: 66.0㎜ ~ 66.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①-664㎜~-66.0㎜②66.0㎜~66.4㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰ(ﾘｱXﾋﾞｰﾑを押す)に当てる"
],
"WorkPoints": [
"Y軸①: -66.4㎜ ~ -66.0㎜ / Y軸②: 66.0㎜ ~ 66.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①1117㎜~(1243.2㎜)②(-1243.2㎜)~-1117㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸①②_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 完了ﾗﾝﾌﾟ点灯を確認し､『終了』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tolks": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_X軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『X AxisD』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"2. 『起動』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へX軸を移動する"
],
"WorkPoints": [
"最大値の位置へX軸を移動後は動かさ無い事(信号調整Startの開始位置になる為)"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､X軸を右側に動かす",
"4. 【信号を確認します】が表示されたら､X軸を左側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上移動させる事",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号Moni... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:min40max80 / Scale B:m... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"3. 『F-X』をｸﾘｯｸする",
"4. 原点ﾌﾟﾘｾｯﾄ値に【 8.0000 】が表示されたら『SET』をｸﾘｯｸする",
"5. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks"... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(−)側ｽﾄﾛｰｸ規格値:7.8㎜~8.2㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾌﾛﾝﾄX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾌﾛﾝﾄX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(+)側ｽﾄﾛｰｸ規格値:968㎜~970㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾌﾛﾝﾄ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾌﾛﾝﾄ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tol... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_Y軸_測定準備",
"WorkItems": [
"2. ㉖（PC）を立ち上げ、アイコン 『Y AxisC』をクリックし、ソフトを立ち上げる",
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"3. 機種選択及びY軸①設定､Y軸②設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"3. Xﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. 『起動』をｸﾘｯｸする",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する",
"1. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞｰﾑを移動後は動かさ無い事(信号調整Startの開始位置になる為... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾘｱ側に戻す",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に動かす"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号M... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸をﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"OKを確認",
"OKを確認",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号Monitor1",
"WorkItems": [
"4. 『終了』を押す",
"1. 『信号Monitor』をｸﾘｯｸする",
"3. ScaleA､B､Cのmax値を比較し､最大値の位置へXﾋﾞｰﾑを移動する",
"2. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"最大値の位置へXﾋﾞｰﾑ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､Xﾋﾞｰﾑをﾌﾛﾝﾄ側に動かす",
"4. 【信号を確認します】が表示されたら､Xﾋﾞｰﾑをﾘｱ側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号M... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸②_信号Monitor2",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"4. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"2. Xﾋﾞｰﾑをﾘｱﾒｶｽﾄｯﾊﾟｰ~ﾌﾛﾝﾄﾒｶｽﾄｯﾊﾟｰまで往復させ測定する"
],
"WorkPoints": [
"Scale A:min40max80 / S... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①②_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸする",
"1. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. 『R側SET』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差測定1",
"WorkItems": [
"2. 『偏差測定』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑを押し【0(ｾﾞﾛ)】付近に移動する",
"4. 3の位置にて『ﾃﾞｰﾀ取込』をｸﾘｯｸする(PCの『Enterｷｰ』でも可)",
"1. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [],
"Tolks": [],
"Inspecti... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差測定2",
"WorkItems": [
"1. Xﾋﾞｰﾑを100㎜づつ移動させ､都度『ﾃﾞｰﾀ取込』をｸﾘｯｸする",
"2. 『終了』をｸﾘｯｸする",
"3. Xﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"移動誤差は±10㎜以内にする事",
"100㎜~1000㎜まで計10回取り込む"
],
"Tolks": [... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_偏差設定",
"WorkItems": [
"1. 『偏差設定』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. 『R側SET』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"3. ﾘｱXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰ(ﾌﾛﾝﾄXﾋﾞｰﾑを押す)に当てる",
"2. ﾘｱXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"Y軸①: -126.4㎜ ~ -126.0㎜ / Y軸②: 126.0㎜ ~ 126.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①-126.4㎜~-126.0㎜②126.0㎜~126.4㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『ｽﾄﾛｰｸ確認』をｸﾘｯｸする",
"3. ﾘｱXﾋﾞｰﾑをﾌﾛﾝﾄ側ﾒｶｽﾄｯﾊﾟｰ(ﾌﾛﾝﾄXﾋﾞｰﾑを押す)に当てる",
"2. ﾘｱXﾋﾞｰﾑをﾘｱ側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"Y軸①: -126.4㎜ ~ -126.0㎜ / Y軸②: 126.0㎜ ~ 126.4㎜",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①1117㎜~(1183.2㎜)②(-1183.2㎜)~-1117㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸①②_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 完了ﾗﾝﾌﾟ点灯を確認し､『終了』をｸﾘｯｸする",
"4. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_Y軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_測定準備",
"WorkItems": [
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"2. ㉖（PC）を立ち上げ、アイコン 『XYCheckerX』をクリックし、ソフトを立ち上げる",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
"Tolks": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_X軸_測定準備",
"WorkItems": [
"1. ㉖のケーブルと本体エンコーダケーブルを接続する",
"2. ㉖（PC）を立ち上げ、アイコン 『XYCheckerX』をクリックし、ソフトを立ち上げる",
"3. 機種選択及び設定のｼﾘｱﾙﾎﾟｰﾄを確認する"
],
"WorkPoints": [
"㉖の電源がOFFになっていることを確認する事"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor1",
"WorkItems": [
"1. ㉖の電源をONにする",
"2. 『起動』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する",
"4. 『信号Monitor』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor2",
"WorkItems": [
"3. 『終了』を押す",
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"2. ScaleA､B､Cのmax値を比較し､最大値の位置へX軸を移動する"
],
"WorkPoints": [
"最大値の位置へX軸を移動後は動かさ無い事(信号調整Startの開始位置になる為)"
],
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号調整START",
"WorkItems": [
"1. 『信号調整Start』をｸﾘｯｸする",
"2. 『開始』をｸﾘｯｸする",
"3. Loopｶｳﾝﾀｰが動き出したら､X軸を右側に動かす",
"4. 【信号を確認します】が表示されたら､X軸を左側に戻す"
],
"WorkPoints": [
"Xﾋﾞｰﾑは50mm/sec以下で60mm以上移動させる事",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_Gain設定確認",
"WorkItems": [
"1. 『Gain設定確認』をｸﾘｯｸし､Scale A,B,Cの判定を確認する",
"2. 『終了』をｸﾘｯｸする",
"3. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:5~8 / Scale B:4~9 / Scale C:4~9",
"NGの場合は信号Monito... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ScaleA:5~8ScaleB:4~9ScaleC:4~9",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_信号Monitor3",
"WorkItems": [
"1. 『信号Monitor』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸする",
"2. X軸を左側ﾒｶｽﾄｯﾊﾟｰ~右側ﾒｶｽﾄｯﾊﾟｰまで往復させ測定する",
"4. X軸を左側ﾒｶｽﾄｯﾊﾟｰまで移動する"
],
"WorkPoints": [
"Scale A:min40max80 / Scale B:min... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:min40max80B:min35max80C:min35max80",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_原点ﾌﾟﾘｾｯﾄ",
"WorkItems": [
"1. X軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"2. 『原点ﾌﾟﾘｾｯﾄ』をｸﾘｯｸする",
"3. 『F-X』をｸﾘｯｸする",
"4. 原点ﾌﾟﾘｾｯﾄ値に【 8.0000 】が表示されたら『SET』をｸﾘｯｸする",
"5. 『終了』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": ... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾘｱX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾘｱX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
"Tol... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(−)側ｽﾄﾛｰｸ規格値:7.8㎜~8.2㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｽﾄﾛｰｸ確認",
"WorkItems": [
"1. 『位置ﾃﾞｰﾀ確認』をｸﾘｯｸする",
"2. ﾘｱX軸を左側ﾒｶｽﾄｯﾊﾟｰに当てる",
"3. ﾘｱX軸を右側ﾒｶｽﾄｯﾊﾟｰに当てる"
],
"WorkPoints": [
"(−) 側ストローク規格値：7.8mm～8.2mm",
"(+) 側ｽﾄﾛｰｸ規格値:968mm~970mm"
],
"Tol... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "(+)側ｽﾄﾛｰｸ規格値:968㎜~970㎜",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_ｴﾗｰ履歴ｸﾘｱ",
"WorkItems": [
"1. 『ｴﾗｰ履歴ｸﾘｱ』をｸﾘｯｸする",
"2. 『ｸﾘｱ』をｸﾘｯｸする",
"3. 『終了』をｸﾘｯｸし､『×』をｸﾘｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "ﾘｱ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾁｪｯｶｰ(NPMｼﾘｰｽﾞ)ｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-5163",
"WorkName": "ﾘｱ側_X軸_XYﾁｪｯｶｰ切り離し",
"WorkItems": [
"1. ㉖の電源をＯＦＦにする",
"2. ㉖のケーブルと本体エンコーダーケーブルを切り離す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5163",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立",
"WorkItems": [
"1. BRACKET にGUIDE PAD をSPACER BOLT BOLT WASHER WASHER で取付"
],
"WorkPoints": [
"下方向に当付けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.6N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"青線部分は端面合わせで取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付",
"WorkItems": [
"1. COVER にLABEL を貼付"
],
"WorkPoints": [
"2mm",
"5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBRACKET(L) をBOLT で取付",
"2. １完成品を㉙に取付"
],
"WorkPoints": [
"①重量物(17kg)運搬は二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBRACKET(L) をBOLT で取付",
"2. １完成品を㉙に取付"
],
"WorkPoints": [
"①重量物(17kg)運搬は二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "先端ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBRACKET(L) をBOLT で取付",
"2. １完成品を㉙に取付"
],
"WorkPoints": [
"①重量物(17kg)運搬は二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"ｶﾞｲﾄﾞが山形になっている場合は中央付近1点でも可",
"規格値:0.1mm"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"ｶﾞｲﾄﾞが山形になっている場合は中央付近1点でも可",
"規格値:0.1mm"
],
"Tolks": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車ｶﾞｲﾄﾞ位置調整ｼﾞｸﾞ(NPM-GH)",
"Size": "",
"ToolOther": "FM-6549",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"ｶﾞｲﾄﾞが山形になっている場合は中央付近1点でも可",
"規格値:0.1mm"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6549",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "台車ｶﾞｲﾄﾞ位置調整ｼﾞｸﾞ(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"ｶﾞｲﾄﾞが山形になっている場合は中央付近1点でも可",
"規格値:0.1mm"
],
"Tolks": [... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ネジを緩めガイドを㉘に押し当て調整",
"㉘を取付",
"治具面とｶﾞｲﾄﾞ面間に平均的にｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"ｶﾞｲﾄﾞが山形になっている場合は中央付近1点でも可",
"規格値:0.1mm"
],
"Tolks": [
"締付ﾄ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "39.0±0.5㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEPJ-G002-C20",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をSCREW で仮取付",
"2. 1完成品にBOLT WASHER を取付",
"3. 2完成品本締め"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をSCREW で仮取付",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をSCREW で仮取付",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GH)",
"Size": "",
"ToolOther": "FM-6331",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付",
"2. 1完成品にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6331",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部置台(NPM-GH)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部ﾌﾞﾛｯｸ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6400",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付",
"2. 1完成品にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6400",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事",
"Method": "交換台車駆動部ﾌﾞﾛｯｸ位置決めｼﾞｸﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付",
"2. 1完成品にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①にBLOCK をBOLT WASHER で取付",
"2. 1完成品にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "固定ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品(H1工程)",
"WorkItems": [
"1. ①BOLT BOLT WASHER BOLT BOLT WASHER ㉒をH1工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認①:『動作ｽｲｯﾁ設定』",
"WorkItems": [
"1. 装着ﾍｯﾄﾞの調整/ｷｬﾘﾌﾞが終了している事",
"2. ①『ﾎｰﾑ』を選択する",
"3. ②『ｻｰﾋﾞｽｴﾝｼﾞﾆｱ』をONにする",
"4. ③『動作ｽｲｯﾁ』を選択",
"5. ④『荷重ﾁｪｯｶｰF･R』､『実負荷(分銅)校正機能』を選択",
"6. ①『ﾎｰﾑ』を選択し⑤『はい』を選択",
"7.... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認②:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』",
"WorkItems": [
"3. ③『荷重ﾁｪｯｶｰ』を選択",
"1. ①『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択",
"2. ②『第4工程』を選択",
"4. ④『荷重ﾁｪｯｶｰ位置測定』を選択する",
"5. 指定されたﾉｽﾞﾙを準備･ｾｯﾄし⑤を選択する",
"6. ⑥『正常に終了しました』の表示が出ていることを確認",
"7. ⑦『ﾒﾝﾃ... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "完了出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "治具分銅ｷｯﾄ",
"Size": "5N",
"ToolOther": "MTKA041625AA",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認③:『出力荷重確認1』",
"WorkItems": [
"1. ①『調整』を選択",
"2. ②『荷重ﾁｪｯｶｰ』を選択",
"3. ③『実荷重計測』を選択",
"4. ④『ｼﾞｸﾞ取付け』を選択",
"5. ｻﾎﾟｰﾄ治具をｾｯﾄし⑤『確認』を選択"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合は... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "治具分銅ｷｯﾄ分銅ｷｯﾄ分銅ｷｯﾄ",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認④:『出力荷重確認2』",
"WorkItems": [
"1. 計測する①『0.5N』を選択し､②『計測ｽﾀｰﾄ』を選択する",
"2. 分銅を取付③『実行』を選択する",
"3. 分銅を取外し④『確認』を選択",
"4. ①『分銅』→1N､5Nそれぞれ作業項目1~4を実施"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認④:『出力荷重確認2』",
"WorkItems": [
"1. 計測する①『0.5N』を選択し､②『計測ｽﾀｰﾄ』を選択する",
"2. 分銅を取付③『実行』を選択する",
"3. 分銅を取外し④『確認』を選択",
"4. ①『分銅』→1N､5Nそれぞれ作業項目1~4を実施"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯ... | {
"QualityItem": "荷重確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.5N:±0.11.0N:±0.15.0N:±0.3",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑤:『動作確認1』",
"WorkItems": [
"1. ①｢機種切替｣を選択",
"2. ②｢生産ﾃﾞｰﾀ選択｣を選択",
"3. 下記注記が表示されるので③｢確認｣を選択",
"4. ④｢簡易ﾃﾞｰﾀ生成｣を選択",
"5. ⑤｢ｵﾌｾｯﾄ反映｣を選択",
"6. ⑥『1005』を選択",
"7. ⑦『ﾉｽﾞﾙ種別230､1001』を選択",
"8. ⑧｢読... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑥:『動作確認2』",
"WorkItems": [
"1. ①『ﾍｯﾄﾞ』を選択する",
"2. ②で指定されたﾉｽﾞﾙを準備する",
"3. ﾁｪﾝｼﾞｬｰにﾉｽﾞﾙをｾｯﾄしﾏｼﾝにｾｯﾄする",
"4. ③『交換』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑥:『動作確認2』",
"WorkItems": [
"1. ①『ﾍｯﾄﾞ』を選択する",
"2. ②で指定されたﾉｽﾞﾙを準備する",
"3. ﾁｪﾝｼﾞｬｰにﾉｽﾞﾙをｾｯﾄしﾏｼﾝにｾｯﾄする",
"4. ③『交換』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "完了出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑦:『動作確認3』",
"WorkItems": [
"1. ①『ﾒﾝﾃﾅﾝｽ』を選択する",
"2. ②『ﾍｯﾄﾞ』を選択する",
"6. ⑥NGになっていないことの確認",
"3. ③『装着荷重計測』を選択する",
"4. ④『全選択』を選択する",
"5. ⑤『計測ｽﾀｰﾄ』を選択する",
"7. 確認後､ﾉｽﾞﾙを外す"
],
"WorkPoints": ... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "警告における上限値・下限値以内である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り1",
"WorkItems": [
"■1. ANALYZER の型式を確認する",
"■2. ANALYZER の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の型式を確認する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表ANALY... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り2",
"WorkItems": [
"1. ①②のｽｲｯﾁを設定する"
],
"WorkPoints": [
"B2004",
"B2005",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF"
],
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り3",
"WorkItems": [
"■1. SENSOR SENSOR SENSOR SENSOR SENSOR の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表SENSOR :APD.1 型式確認"
],
"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り4",
"WorkItems": [
"1. ①②③を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰを下げてﾛｯｸする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "55cN･m",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B200... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B2004",
"B9_B2004"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り6",
"WorkItems": [
"1. ①にJOINT JOINT JOINT を取付ける"
],
"WorkPoints": [
"ﾒｲﾝｴｱ圧用ﾃﾞｼﾞﾀﾙｹﾞｰｼﾞに接続された配管を外してJOINT に接続する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｱﾅﾗｲｻﾞ取付け",
"WorkItems": [
"1. RAIL にTERMINAL-BLOCK を取付ける",
"2. 1完成品をBOLT WASHER で架台に取付ける",
"3. ③を取付ける"
],
"WorkPoints": [
"上側を引掛け矢印方向に押して取付ける",
"ﾚｰﾙ端面に合わせて取付けのこと",
"矢印方向に当付け取付けのこと",
"上側を引掛け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "ｾｰﾌﾃｨｺﾝﾄﾛｰﾗ取付け",
"WorkItems": [
"1. TERMINAL-SUPPORT を取付ける",
"3. TERMINAL-BLOCK を取付ける",
"4. ｹｰﾌﾞﾙを固定する",
"2. ｾｰﾌﾃｨｺﾝﾄﾛｰﾗを取付ける"
],
"WorkPoints": [
"矢印方向に当付け取付けのこと",
"矢印方向に当付け取付けのこと"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 配線を引き回し固定する"
],
"WorkPoints": [
"B130/1/2/3/4P",
"CX1221TM3R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し・接続",
"WorkItems": [
"★1. CABLE を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"MTKC036462"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し・接続",
"WorkItems": [
"★1. CABLE を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"MTKC036462"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"InspectionItems": [
"検査表CABLE :APD.6 ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. 配線を引き回し固定する"
],
"WorkPoints": [
"B130/1/2/3/4P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀ... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧ｾﾝｻｰ接続",
"WorkItems": [
"1. 各ｾﾝｻｰを接続する"
],
"WorkPoints": [
"B131P",
"B132P",
"B133P",
"B130P",
"B134P",
"SD-EJM8EB1-611で配線した各空圧ｾﾝｻｰを接続する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A03",
"I... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｰ切替ﾊﾞﾙﾌﾞ・ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部配管接続",
"WorkItems": [
"1. ｴｱｰｹﾞｰｼﾞﾕﾆｯﾄ部の配管を接続し､配管を固定する"
],
"WorkPoints": [
"配管折れに注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｺｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立①",
"WorkItems": [
"1. BRACKET に油砥石かけ"
],
"WorkPoints": [
"指定箇所に油砥石をかける",
"油砥石かけ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "脱脂確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所が脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.