input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立①",
"WorkItems": [
"1. BRACKET に油砥石かけ"
],
"WorkPoints": [
"指定箇所に油砥石をかける",
"油砥石かけ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立②",
"WorkItems": [
"◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. 1の完成品へLABEL を指定の寸法で貼付ける",
"◆3. BOLT SPRING にｸﾞﾘｰｽ塗布"
],
"WorkPoints": [
"指示箇所へ塗布する",
"3mm",
"1mm",
"4mm",
"1mm",
"3m... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆2個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立②",
"WorkItems": [
"◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する",
"2. 1の完成品へLABEL を指定の寸法で貼付ける",
"◆3. BOLT SPRING にｸﾞﾘｰｽ塗布"
],
"WorkPoints": [
"指示箇所へ塗布する",
"3mm",
"1mm",
"4mm",
"1mm",
"3m... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:各1個",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立③",
"WorkItems": [
"1. ①にPIN を圧入",
"2. 1の完成品にCOLLAR BOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安出代:10㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "切替台座部(支持部側)組立③",
"WorkItems": [],
"WorkPoints": [
"PIN の出代10mm",
"PIN の圧入方向､場所に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立④",
"WorkItems": [
"1. ①にPLATE ③④を取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "切替台座部(支持部側)組立④",
"WorkItems": [
"1. ①にPLATE ③④を取付"
],
"WorkPoints": [
"PLATE の取付方向に注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑤",
"WorkItems": [
"1. ①にBOLT WASHER を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"②の取付向きに注意(下図参照)",
"BOLT WASHER を挿入してから②を取付する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "切替台座部(支持部側)組立⑤",
"WorkItems": [
"1. ①にBOLT WASHER を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"②の取付向きに注意(下図参照)",
"BOLT WASHER を挿入してから②を取付する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionN... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑥",
"WorkItems": [
"1. ①にBOLT を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"BOLT を挿入してから②を取付する事",
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "切替台座部(支持部側)組立⑥",
"WorkItems": [
"1. ①にBOLT を挿入し､②をBOLT WASHER で取付"
],
"WorkPoints": [
"BOLT を挿入してから②を取付する事",
"②の取付向きに注意(下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑦",
"WorkItems": [
"1. ①にCAP を挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑧",
"WorkItems": [
"◆1. ①のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け"
],
"WorkPoints": [
"各銘板の貼付け向きに注意(下図参照)",
"3mm",
"3mm",
"3mm",
"3mm",
"4mm",
"ﾗﾍﾞﾙ貼付け面"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "脱脂確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所が脱脂されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "切替台座部(支持部側)組立⑧",
"WorkItems": [
"◆1. ①のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け"
],
"WorkPoints": [
"各銘板の貼付け向きに注意(下図参照)",
"3mm",
"3mm",
"3mm",
"3mm",
"4mm",
"ﾗﾍﾞﾙ貼付け面"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "貼付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. BRACKET へLINEAR-SCALE (S/N $$$$$$$$-02)をBOLT WASHER で取付ける",
"3. BRACKET へLINEAR-SCALE (S/N ********-01)をBOLT WASHER で取付ける",
"1. LINEAR-SCALE LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を記入する"
],
"WorkPoin... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立",
"WorkItems": [
"2. BRACKET へLINEAR-SCALE (S/N $$$$$$$$-02)をBOLT WASHER で取付ける",
"3. BRACKET へLINEAR-SCALE (S/N ********-01)をBOLT WASHER で取付ける",
"1. LINEAR-SCALE LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を記入する... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"2. Yフレームに㉖を置いてMOTOR を置く"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事"... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-3046",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者側な... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸可動子(REAR-左側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"MOTOR の配線が作業者... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事",
"型式確認､ｼﾘｱﾙNo.記入"... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-3046",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"ﾈｼﾞ穴を合わせ､MOTOR ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"型式確認､ｼﾘｱﾙNo.記入",
"ﾈｼﾞ穴を合わせ､MOTO... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸可動子(REAR-右側)取付",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNo.を記入する",
"2. Yフレームに㉖を置いてMOTOR を置く",
"4. ㉖を取り外す",
"3. MOTOR をX軸にBOLT WASHER で固定する"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込む事",
"MO... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)①",
"WorkItems": [
"◆1. MOTOR を㉖へ表示通りにセットする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)①",
"WorkItems": [
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする",
"◆1. MOTOR を㉖へ表示通りにセットする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6607",
"WorkName": "Y軸固定子取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6607",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付③",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)④",
"WorkItems": [
"◆1. MOTOR を②へ表示通りにｾｯﾄする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)④",
"WorkItems": [
"◆1. MOTOR を②へ表示通りにｾｯﾄする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ保護ｼﾞｸﾞ(中央取付用)",
"Size": "",
"ToolOther": "FM-6605",
"WorkName": "Y軸固定子取付⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6605",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付⑥",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付(準備)⑦",
"WorkItems": [
"◆1. MOTOR を㉖へ表示通りにセットする",
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付(準備)⑦",
"WorkItems": [
"■◆2. MOTOR の『ｼﾘｱﾙNo､型式の確認』及び『傷､打痕の確認』をする",
"◆1. MOTOR を㉖へ表示通りにセットする"
],
"WorkPoints": [
"MOTOR に磁性体を50㎜以内に近づけ無い事",
"極性を間違えない様､注意する事",
"型式確認､ｼﾘｱﾙNo.記入",
"･MOTOR の保護ｶﾊﾞｰを開ける際は､1枚毎... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.6N･m",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "部品落下防止ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-4900",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4900",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ保護ｼﾞｸﾞ(ﾘｱ側取付用)",
"Size": "",
"ToolOther": "FM-6606",
"WorkName": "Y軸固定子取付⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6606",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾏｸﾞﾈｯﾄ極性の間違い無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付⑨",
"WorkItems": [
"◆1. 固定子の保護ｶﾊﾞｰを取り外し､粘着ﾃｰﾌﾟにて鉄粉を取り除く"
],
"WorkPoints": [
"･固定子に磁性体を50㎜以内に近づけ無い事･下側固定子の保護ｶﾊﾞｰﾋﾞｽを緩めてから上側固定子ｶﾊﾞｰを取り外す事･作業はM/C内側より実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付(右側)",
"WorkItems": [
"1. 本体に①②COVER をSCREW で取付ける"
],
"WorkPoints": [
"･上側ｶﾊﾞｰ:上に押し付け取付ける事･下側ｶﾊﾞｰ:固定金具取付穴に合わせ､Yﾌﾚｰﾑと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸固定子簡易保護ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-3050",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付(右側)",
"WorkItems": [
"1. 本体に①②COVER をSCREW で取付ける"
],
"WorkPoints": [
"･上側ｶﾊﾞｰ:上に押し付け取付ける事･下側ｶﾊﾞｰ:固定金具取付穴に合わせ､Yﾌﾚｰﾑと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3050",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5858",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5858",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"高さｹﾞｰｼﾞﾌﾞﾛｯｸ",
"高さｹﾞｰｼﾞﾌﾞﾛ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"高さｹﾞｰｼﾞﾌﾞﾛｯｸ",
"高さｹﾞｰｼﾞﾌﾞ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "FM-6090",
"ToolOther": "3.6N･m",
"WorkName": "ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄ高さ調整",
"WorkItems": [],
"WorkPoints": [
"高さゲージブロックに押し当て㉘を固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"Tolks": [
... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"To... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表②:... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LED照明の下面よりも下方向に垂れ下がら無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT 2 :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT 2 :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
],
"Tolks... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付①",
"WorkItems": [
"■1. HEAD CAMERA UNIT 2 :WD42 の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾍｯﾄﾞｶﾒﾗﾌﾟﾚｰﾄにHEAD CAMERA UNIT 2 :WD42 をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗの位置決め穴とﾌﾟﾚｰﾄの位置決めﾋﾟﾝを合わせる事"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ",
"ToolOther": "15cN･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LED照明の下面よりも下方向に垂れ下がら無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付③",
"WorkItems": [
"1. CLIP をBOLT で取付ける"
],
"WorkPoints": [
"OP;高さｾﾝｻ仕様がある場合はCLIP BOLT 取付不要"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する",
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表CABLE :... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP】高さｾﾝｻｰ取付①",
"WorkItems": [
"1. CLIP をBOLT で取付ける",
"2. CABLE-SUPPORT SPACER をBOLT で取付ける",
"1. CLIP をBOLT で取付ける",
"2. CABLE-SUPPORT SPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP】高さｾﾝｻｰ取付②",
"WorkItems": [
"1. ①をBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:HS1.高さｾﾝｻﾕﾆｯﾄの取付(取付確認)"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】高さｾﾝｻｰ取付③",
"WorkItems": [
"1. 配線を引き回し、㉖㉗で固定する（フェライトコアから固定）",
"2. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [
"ﾌｪﾗｲﾄｺｱの中央をﾏｳﾝﾄに合わせて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線用ﾏｳﾝﾄ取付",
"WorkItems": [
"1. YﾌﾚｰﾑへCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"8箇所",
"取付方向"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ㉘（位置決め用M4ダミーネジ）を取り外す"
],
"WorkPoints": [
"㉘のダミーネジを入れてから押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付①",
"WorkItems": [
"1. ①へNUT-BLOCK NUT-BLOCK BRACKET をBOLT WASHER BOLT WASHER で仮取付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Y軸ﾍﾞｱ",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:7.組立時調整"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸固定子簡易保護ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-3050",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3050",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9N･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9N･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "194cN･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "194cN･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "WETE-G002... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜ﾛﾝｸﾞﾋﾞｯﾄ",
"ToolOther": "55cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理1",
"WorkItems": [
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM503】をBOLT WASHER で取付け､配線を固定する",
"2. ﾓｰﾀｺﾈｸﾀ【XMM503】を接続し､配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理1",
"WorkItems": [
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM503】をBOLT WASHER で取付け､配線を固定する",
"2. ﾓｰﾀｺﾈｸﾀ【XMM503】を接続し､配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍｯﾄﾞ部配線処理2",
"WorkItems": [
"1. ①をBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾄﾘﾑをM/Cの内側に向... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理3",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"《右側面》",
"《左側面》",
"右側面へ",
"左側面へ",
"浮き上が... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理4",
"WorkItems": [
"■1. ｱｰｽ線をSCREW で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:2.ﾈｼﾞ締めﾄﾙｸ確認/ｱｰｽﾗﾍﾞﾙ貼付け確認(2)R... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理5",
"WorkItems": [
"1. ﾓｰﾀｰ線を固定する",
"2. ｴｱｰﾎｰｽ(白､黄)を接続し､ﾓｰﾀｰ線に固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸの頭は下へ向ける",
"《... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.6N･m",
"WorkName": "ﾍｯﾄﾞ部配線処理6",
"WorkItems": [
"1. ｶﾒﾗｹｰﾌﾞﾙをSPACER SHIELD BOLT WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理6",
"WorkItems": [
"1. ｶﾒﾗｹｰﾌﾞﾙをSPACER SHIELD BOLT WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 (2)R側 2-4.... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理7",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞｰｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 2-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"XEM... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】ﾍｯﾄﾞ部配線処理(高さｾﾝｻ、文字認識仕様)",
"WorkItems": [
"1. 配線【CN 5､CN13】をXEM503に固定する"
],
"WorkPoints": [
"仕様を確認し､配線を引き回しする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "43cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理8",
"WorkItems": [
"2. ﾄﾞﾛﾜ配線を固定する",
"1. 『1A22』をSCREW WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾞﾗｹｯﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "43cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理10",
"WorkItems": [
"■1. 配線を仮締めし､『FGFX1』『FGFX2』をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:2.ﾈｼﾞ締めﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表②... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理12",
"WorkItems": [
"★1. LED制御基板をSPACER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"★静電対策... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理13",
"WorkItems": [
"1. 配管(黒､白)を接続し､固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■1. ①へｶﾒﾗｹｰﾌﾞﾙ(CMRR)を固定する",
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMRP)に接続し､BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "120cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMRP)に接続し､BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMRP)に接続し､BOLT で取付ける",
"■1. ①へｶﾒﾗｹｰﾌﾞﾙ(CMRR)を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理1",
"WorkItems": [
"1. X軸の左側から右側に可動子配線【YMM508】ｴﾝｺｰﾀﾞ配線【YEM508】を引き回す",
"2. 可動子配線【YMM508】をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM508】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.