input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM508】を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理3",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞ配線【YEM508】をﾌﾞﾗｹｯﾄに接続する",
"2. 可動子配線【YMM508】ｴﾝｺｰﾀﾞ配線【YEM508】をXﾋﾞｰﾑ下面に固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理1",
"WorkItems": [
"1. 可動子配線【YMM504】ｴﾝｺｰﾀﾞ配線【YEM504】を引き回す",
"2. 可動子配線【YMM504】をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM504】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM504】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理3",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞ配線【YEM504】をﾌﾞﾗｹｯﾄに接続する",
"2. 【YMM508】【YEM508】【YMM504】【YEM504】を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける",
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.8N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "6",
"ToolOther": "100cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理",
"WorkItems": [
"1. X軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(300mm)",
"配線の余長吸収箇所",
"ﾍｯﾄﾞをX軸左側ﾒ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "Y軸干渉ｾﾝｻ配線処理1",
"WorkItems": [
"■1. Y軸干渉ｾﾝｻ配線(B113R)を引き回し､FG線(FGRY1)をSCREW で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸干渉ｾﾝｻ配線処理1",
"WorkItems": [
"■1. Y軸干渉ｾﾝｻ配線(B113R)を引き回し､FG線(FGRY1)をSCREW で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:2.ﾈｼﾞ締めﾄﾙｸ確認/ｱｰｽﾗﾍﾞﾙ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸干渉ｾﾝｻ配線処理2",
"WorkItems": [
"1. Y軸干渉センサを引き回し、㉗で固定する",
"2. 余長をまとめて㉖で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"余長と一緒に固定する事",
"余長は矢印の方... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理1",
"WorkItems": [
"1. Y軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理2",
"WorkItems": [
"2. 架台に配線を引き回し固定する",
"1. ﾍﾞｱ配管を接続し､ﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"CNP3K503CN... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理3",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"2. 架台に配線を引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ﾌﾛﾝﾄへCN4K303",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理4",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"■2. XY軸ﾄﾞﾗｲﾊﾞｰに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理5",
"WorkItems": [
"1. ﾊﾟﾜｰﾕﾆｯﾄｺﾈｸﾀﾌﾞﾗｹｯﾄに配線を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:6.XY配線ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理6",
"WorkItems": [
"■1. CN中継基板(K313)に配線を接続し､FG線をSCREW で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:6.XY... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽﾁｭｰﾌﾞ取付",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"正面図(ﾘｱ)",
"A部",
"B部",
"左→手前",
"B部",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙ取付(右側)",
"WorkItems": [
"1. 架台へ①をBOLT で取付ける"
],
"WorkPoints": [
"①を取付ける際は､2名作業を徹底する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.4",
"Size": "",
"ToolOther": "FM-2707",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.5",
"Size": "",
"ToolOther": "FM-2969",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付2",
"WorkItems": [
"1. リニアスケールヘッドのコネクタを接続し、㉖㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 2-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｵｲﾙ受けｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"正面図(ﾘｱ)",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "部品落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾞﾗｹｯﾄと厚肉の... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｾｯﾄﾋﾞｽ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6634",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [
"1. SPACER へSCREW を挿入する",
"2. SPACER へ㉖をセットし、SCREW を挿入する",
"3. 1の完成品と2の完成品を本体へ取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6634",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "10.0N･m",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [],
"WorkPoints": [
"本体取付時に都度作成する事"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左側面",
"右側面",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ配線接続(右側)",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線を接続する",
"■2. FG線をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ配線接続(左側)①",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線､配管を引き回す"
],
"WorkPoints": [
"配管接続確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:1.ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認【配管の接続確認】"
],
"WorkTypes... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ配線接続(左側)②",
"WorkItems": [
"■2. FG線をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表SCREW :1.CN中継基板(搬送)接続確... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ配線接続(左側)③",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線(EXTOT3)を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:2.SIO基板#1(K311) ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Word... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ配線接続(右側)",
"WorkItems": [
"■2. FG線をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表SCREW :1.CN中継基板(搬送)接続確認... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ配線接続(左側)①",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線､配管を引き回す"
],
"WorkPoints": [
"配管接続確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:1.ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認【配管のい接続確認】"
],
"WorkType... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ配線接続(左側)②",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線を接続する",
"■2. FG線をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ配線接続(左側)③",
"WorkItems": [
"1. ｺﾝﾍﾞﾔｰ配線(EXTOT3)を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:2.SIO基板#1(K311) ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Word... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾊﾞﾙﾌ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "190cN･m",
"WorkName": "ﾍｯﾄﾞｶﾊﾞｰ取付",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 190cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "190cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付1(前後共通)",
"WorkItems": [
"2. SPACER に1完成品をBOLT で取付",
"■1. LOAD-CELL の型式､製造番号を確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの配線を図の向きにて取付",
"向き有 ﾀｯﾌﾟ穴注意",
"LOAD-CELL の端面をSPACER に合わせる",
"㉘を挟みSPACER に端面を合わせる"
],
"... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D12",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.6㎜",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付1(前後共通)",
"WorkItems": [
"2. SPACER に1完成品をBOLT で取付",
"■1. LOAD-CELL の型式､製造番号を確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの配線を図の向きにて取付",
"向き有 ﾀｯﾌﾟ穴注意",
"LOAD-CELL の端面をSPACER に合わせる",
"㉘を挟みSPACER に端面を合わせ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "2.6㎜を挟んで取付",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "41cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付1(前後共通)",
"WorkItems": [
"2. SPACER に1完成品をBOLT で取付",
"■1. LOAD-CELL の型式､製造番号を確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの配線を図の向きにて取付",
"向き有 ﾀｯﾌﾟ穴注意",
"LOAD-CELL の端面をSPACER に合わせる",
"㉘を挟みSPACER に... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "41cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付2(前後共通)",
"WorkItems": [
"1. ①にCOVER SPACER をBOLT WASHER で取付"
],
"WorkPoints": [
"COVER ｶﾊﾞｰとﾛｰﾄﾞｾﾙが干渉しないように取付",
"認識ﾏｰｸが図の位置にくるように取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部取付1(前後共通)",
"WorkItems": [
"2. 1完成品にBLOCK を取付",
"1. SHAFT にSCREW を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｼｬﾌﾄ部取付2(前後共通)",
"WorkItems": [
"2. 1完成品を平行に取付"
],
"WorkPoints": [
"P004にﾌﾞﾛｯｸｹﾞｰｼﾞを挟み､BOLT を固定し､ｶﾞﾀつきが無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkType... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "15.5㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部取付2(前後共通)",
"WorkItems": [
"2. 1完成品を平行に取付"
],
"WorkPoints": [
"P004にﾌﾞﾛｯｸｹﾞｰｼﾞを挟み､BOLT を固定し､ｶﾞﾀつきが無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付できている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬﾌﾄ部取付3(前後共通)",
"WorkItems": [
"1. ①に②を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｼｬﾌﾄ部取付3(前後共通)",
"WorkItems": [
"2. 1完成品にCLIP をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部配線(前後共通)",
"WorkItems": [
"1. ①にｲﾝｼｭﾛｯｸを取付"
],
"WorkPoints": [
"P002下面から24±3mm",
"青丸部分は線が張りすぎないよう取付の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "24㎜±3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "48cN･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ部取付(FrontorRear)",
"WorkItems": [
"1. BRACKET にCABLE またはCABLE をBOLT で取付"
],
"WorkPoints": [
"凸部の方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 48cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "48cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "製造番号・型式確認(FrontorRear)",
"WorkItems": [
"■1. LOAD-CELL-AMP の型式･製造番号を確認し､検査表に記入"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D12",
"InspectionItems": [
"検査表LOAD-CELL-AMP :型式･検査... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D12",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "ｱﾝﾌﾟ取付(FrontorRear)",
"WorkItems": [
"2. 1完成品にTERMINAL-SUPPORT ③を取付",
"4. SPACER にCABLE-SUPPORT SCREW を取付"
],
"WorkPoints": [
"付属ﾈｼﾞで取付",
"矢印方向に寄せながら締付",
"TERMINAL-SUPPORT ③共に左側に当付けて取付",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱﾝﾌﾟ取付(FrontorRear)",
"WorkItems": [
"2. 1完成品にTERMINAL-SUPPORT ③を取付",
"4. SPACER にCABLE-SUPPORT SCREW を取付"
],
"WorkPoints": [
"付属ﾈｼﾞで取付",
"矢印方向に寄せながら締付",
"TERMINAL-SUPPORT ③共に左側に当付けて取付",
"8.5mm"
],
... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "69cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(FrontorRear)",
"WorkItems": [
"■1. ①に②の配線を取付",
"■2. 1完成品にCABLE CABLE またはCABLE CABLE を取付"
],
"WorkPoints": [
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"奥まで差込み､軽く電線を引いて､確実にｸﾗﾝﾌﾟされていることを確認",
"各ﾋﾟﾝに付いているﾎﾞﾀﾝ(... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "69cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(FrontorRear)",
"WorkItems": [
"■1. ①に②の配線を取付",
"■2. 1完成品にCABLE CABLE またはCABLE CABLE を取付"
],
"WorkPoints": [
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"奥まで差込み､軽く電線を引いて､確実にｸﾗﾝﾌﾟされていることを確認",
"各ﾋﾟﾝに付いているﾎﾞﾀﾝ(... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "FM-6261",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ通信設定確認(FrontorRear)",
"WorkItems": [
"5. 下図のように通信設定内容を確認し保存する",
"4. ㉖でプログラム（TD-SC1 Setup）を起動する",
"3. ①のコネクタに㉘をつなぎ電源を入れる",
"2. ①と㉖を㉗で繋ぐ（黄丸）",
"1. ①のｽｲｯﾁを右図のようにUSB(下側)に変更する(黄矢印)"
],
"WorkPoints": [
... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6261",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定で来ている事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WETE-G002-D12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定(FrontorRear)",
"WorkItems": [
"5. 下図のように通信設定内容を確認し保存する",
"4. ㉖でプログラム（TD-SC1 Setup）を起動する",
"3. ①のコネクタに㉘をつなぎ電源を入れる",
"2. ①と㉖を㉗で繋ぐ（黄丸）",
"1. ①のｽｲｯﾁを右図のようにUSB(下側)に変更する(黄矢印)"
],
"WorkPoints": [
"... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D12",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定(FrontorRear)",
"WorkItems": [
"1. ｽｲｯﾁ設定",
"2. 製造識別ｼｰﾙ貼付け"
],
"WorkPoints": [
"矢印の方向にｽｲｯﾁを設定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品",
"WorkItems": [
"1. CABLE を次工程に払い出し"
],
"WorkPoints": [
"前後取付仕様の場合はﾏｼﾝに対して1本なので払い出しはCABLE 1本の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左右、内ｶﾞｲﾄﾞ部組立",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER SCREW で取付"
],
"WorkPoints": [
"GUIDE の傾斜部の向きに注意し､図のように左右反対の物を組立",
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄSCREW の頭のみにする",
"青線の部分を端面合わせする事"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "左右、内ｶﾞｲﾄﾞ部組立",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER SCREW で取付"
],
"WorkPoints": [
"GUIDE の傾斜部の向きに注意し､図のように左右反対の物を組立",
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄSCREW の頭のみにする",
"青線の部分を端面合わせする事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右外ｶﾞｲﾄﾞ部組立",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER で仮取付",
"2. 1完成品にBRACKET をBOLT WASHER で仮取付"
],
"WorkPoints": [
"GUIDE の傾斜部の向きに注意",
"BRACKET の長穴のだいたい中心で取付"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左外ｶﾞｲﾄﾞ部組立",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER で仮取付",
"2. 1完成品にBRACKET をBOLT WASHER で仮取付"
],
"WorkPoints": [
"GUIDE の傾斜部の向きに注意",
"BRACKET の長穴のだいたい中心で取付"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "上昇抑制圧機構組立-1",
"WorkItems": [
"2. 1完成品にLEVER をBOLT WASHER で取付"
],
"WorkPoints": [
"LEVER は図の方向で取付",
"SHAFT を通す際にﾍﾞｱﾘﾝｸﾞとｶﾗｰに若干のずれ等有る為注意の事",
"SPRING の挿入方向に注意",
"SPRING 全体(表裏)にﾁｭ-ﾌﾞ10㎜のｸﾞﾘｰｽを塗布する"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.6N･m",
"WorkName": "上昇抑制圧機構組立-1",
"WorkItems": [
"1. HOLDER へCOLLAR を入れBEARING を取付",
"◆3. BRACKET に2完成品とSPRING COLLAR をSHAFT BOLT WASHER で取付"
],
"WorkPoints": [
"SPRING 表裏に満遍なく塗布",
"BEARING のﾍﾞｱﾘﾝｸﾞは挿入の際に傾きやすいので傾きに注意して挿入",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上昇抑制圧機構組立-1",
"WorkItems": [
"1. HOLDER へCOLLAR を入れBEARING を取付",
"2. 1完成品にLEVER をBOLT WASHER で取付",
"◆3. BRACKET に2完成品とSPRING COLLAR をSHAFT BOLT WASHER で取付"
],
"WorkPoints": [
"SPRING 表裏に満遍なく塗布",
"LEVER は図の方向で取付",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｸﾞﾘｰｽ容器:各10㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "上昇抑制圧機構組立-2",
"WorkItems": [
"1. ①にBEARING SPACER をBOLT NUT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"平らな面"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "上昇抑制圧機構組立-2",
"WorkItems": [
"2. 1完成品にSPACER BOLT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上昇抑制圧機構組立-2",
"WorkItems": [
"1. ①にBEARING SPACER をBOLT NUT で取付",
"2. 1完成品にSPACER BOLT を取付",
"◆3. ﾊﾞﾈかけ部にｸﾞﾘｰｽｱｯﾌﾟ"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "保護ﾃｰﾌﾟ貼付",
"WorkItems": [
"1. COVER へTAPE を貼付"
],
"WorkPoints": [
"貼付け面を清掃の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3㎜",
"3㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "可動ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE へBLOCK をBOLT WASHER で取付"
],
"WorkPoints": [
"BLOCK は矢印方向に当てつけて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "可動ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"2. 1完成品にPLATE をBOLT WASHER で取付"
],
"WorkPoints": [
"㉚の上で㉛を下に置き当てつけて固定"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "可動ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"2. 1完成品にPLATE をBOLT WASHER で取付"
],
"WorkPoints": [
"㉚の上で㉛を下に置き当てつけて固定"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "下面を定盤上で合わせて固定する事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "10.5㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"2. 1完成品にPLATE をBOLT WASHER で取付"
],
"WorkPoints": [
"㉚の上で㉛を下に置き当てつけて固定"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "10.5㎜を挟み取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立",
"WorkItems": [
"2. BLOCK へPIN を圧入する"
],
"WorkPoints": [
"PIN の割の方向注意",
"出代 5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立",
"WorkItems": [
"3. PLATE の反り確認"
],
"WorkPoints": [
"0.1mmが通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BLOCK :P001のｿﾘ確認･P002平行度確認"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部調整ｽﾀﾝﾄﾞ",
"Size": "",
"ToolOther": "FM-4851",
"WorkName": "ﾍﾞｰｽ部組立",
"WorkItems": [
"3. PLATE の反り確認"
],
"WorkPoints": [
"0.1mmが通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BLOCK :P001のｿﾘ確認･P002平... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-4851",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "引き出部調整ｽﾀﾝﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立",
"WorkItems": [
"3. PLATE の反り確認"
],
"WorkPoints": [
"0.1mmが通ら無い事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C034",
"InspectionItems": [
"検査表BLOCK :P001のｿﾘ確認･P002平行度確認"
],
"WorkTypes... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C034",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立2",
"WorkItems": [
"1. ①に②をBOLT で取付",
"2. 1完成品にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"㉗を①のDピンに合わせる",
"Dﾋﾟﾝ位置",
"STOPPER を矢印方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ吸着部LMｶﾞｲﾄﾞ平行だしｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5063",
"WorkName": "ﾍﾞｰｽ部組立2",
"WorkItems": [
"1. ①に②をBOLT で取付",
"2. 1完成品にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"㉗を①のDピンに合わせる",
"Dﾋﾟﾝ位置",
"STOPPER を矢印方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5063",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍﾞｰｽ部組立2",
"WorkItems": [
"1. ①に②をBOLT で取付",
"2. 1完成品にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"㉗を①のDピンに合わせる",
"Dﾋﾟﾝ位置",
"STOPPER を矢印方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立2",
"WorkItems": [
"1. ①に②をBOLT で取付",
"2. 1完成品にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"㉗を①のDピンに合わせる",
"Dﾋﾟﾝ位置",
"STOPPER を矢印方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C034",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾍﾞｰｽ部組立2",
"WorkItems": [
"1. ①に②をBOLT で取付",
"2. 1完成品にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"㉗を①のDピンに合わせる",
"Dﾋﾟﾝ位置",
"STOPPER を矢印方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"線有りが基準面",
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
"㉙を矢印方向に当付け、付属の... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C034",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
"㉙を矢印方向に当付け、付属のクランプで固定し",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ吸着部LMｶﾞｲﾄﾞ平行だしｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5063",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5063",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "ﾄﾚｲﾌｨｰﾀﾞ吸着部LMｶﾞｲﾄﾞ平行だしｼﾞｸﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ吸着部LMｶﾞｲﾄﾞ平行だしｼﾞｸﾞ(G10)",
"Size": "",
"ToolOther": "FM-6402",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"線有りが基準面",
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-6402",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "ﾄﾚｲﾌｨｰﾀﾞ吸着部LMｶﾞｲﾄﾞ平行だしｼﾞｸﾞ(G10)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
"㉙を矢印方向に当付け、付属のクラ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C034",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
"㉙を矢印方向に当付け、... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. LINEAR-WAY の型式､ｼﾘｱﾙNo確認",
"2. ①へLINEAR-WAY をBOLT で取付",
"4. ㉗を取外す"
],
"WorkPoints": [
"線有りが基準面",
"LINEAR-WAY のLMｶﾞｲﾄﾞの基準面を矢印方向にて取付",
"LINEAR-WAY の位置決めを㉙で行う",
"㉙を矢印方向に当付け、付属の... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆粒:各3",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "可動ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①へ②をBOLT WASHER で取付"
],
"WorkPoints": [
"LMガイドと②の左面を矢印方向に㉗で面合わせ（黄線）して固定する",
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄ頭のみにする"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.