input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "40N･m",
"WorkName": "左側交換台車駆動部取付(OP:17連切替仕様)",
"WorkItems": [
"2. 1完成品に②を接続する",
"◆1. ①をﾋﾟﾝに挿入し付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"中のﾎﾞﾙﾄ締結",
"付属ﾎﾞﾙﾄ",
"付属ﾎﾞﾙﾄ",
"調整後再締結付属ﾎﾞﾙﾄ",
"位置決めﾋﾟﾝ",
"重量物",
"㉜に①をセットしリフターを使用し架台へドッキングする事",
"②は接続場所に注意する",
"赤ｷｬｯﾌﾟ側"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 40N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部取付ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6384",
"WorkName": "左側交換台車駆動部取付(OP:17連切替仕様)",
"WorkItems": [
"2. 1完成品に②を接続する",
"◆1. ①をﾋﾟﾝに挿入し付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"中のﾎﾞﾙﾄ締結",
"付属ﾎﾞﾙﾄ",
"付属ﾎﾞﾙﾄ",
"調整後再締結付属ﾎﾞﾙﾄ",
"位置決めﾋﾟﾝ",
"重量物",
"㉜に①をセットしリフターを使用し架台へドッキングする事",
"②は接続場所に注意する",
"赤ｷｬｯﾌﾟ側"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 40N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6384",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "左側交換台車駆動部取付(OP:17連切替仕様)",
"WorkItems": [
"2. 1完成品に②を接続する",
"◆1. ①をﾋﾟﾝに挿入し付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"中のﾎﾞﾙﾄ締結",
"付属ﾎﾞﾙﾄ",
"付属ﾎﾞﾙﾄ",
"調整後再締結付属ﾎﾞﾙﾄ",
"位置決めﾋﾟﾝ",
"重量物",
"㉜に①をセットしリフターを使用し架台へドッキングする事",
"②は接続場所に注意する",
"赤ｷｬｯﾌﾟ側"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 40N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換台車駆動部配線処理(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"1. ｺﾈｸﾀﾌﾞﾗｹｯﾄに配線･配管を接続し､ｲﾝｼｭﾛｯｸで固定する",
"2. ｺﾈｸﾀﾌﾞﾗｹｯﾄに配線･配管を接続し､ｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"配管白ﾗｲﾝ",
"1S3711R",
"接続確認",
"右側交換台車:17連交換台車仕様､切替仕様､ﾄﾚｲ仕様時に下記作業を行う",
"配管白ﾗｲﾝ",
"1S3211R",
"接続確認",
"左側交換台車:17連交換台車､切替仕様時下記作業を行う",
"設備左側作業",
"設備右側作業",
"ﾄﾚｲ切替仕様時は写真部分の様に取り外し",
"1S3211R",
"配管白ﾗｲﾝ",
"赤ｷｬｯﾌﾟ側",
"17連交換台車仕様",
"切替仕様時"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:台車引込みﾕﾆｯﾄ中継接続確認 Rear",
"検査表①:台車引込みﾕﾆｯﾄ中継接続確認 Rear",
"ﾘｱ",
"WETE-G002-D07"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "交換台車支持部取付(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"◆1. ①②③をBOLT BOLT で取付ける"
],
"WorkPoints": [
"②をﾋﾟﾝに挿入する",
"治具を使用し本体に取付ける",
"①②③を㉘の３か所に引っ掛け設置する",
"重量物",
"治具に①②③をｾｯﾄし架台へﾄﾞｯｷﾝｸﾞする事",
"17連/17連台車仕様は①③､17連/ﾄﾚｲ仕様/切替仕様は②を取付ける",
"③は左右17連交換台車仕様の時取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車支持部取付ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6609",
"WorkName": "交換台車支持部取付(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"◆1. ①②③をBOLT BOLT で取付ける"
],
"WorkPoints": [
"②をﾋﾟﾝに挿入する",
"治具を使用し本体に取付ける",
"①②③を㉘の３か所に引っ掛け設置する",
"重量物",
"治具に①②③をｾｯﾄし架台へﾄﾞｯｷﾝｸﾞする事",
"17連/17連台車仕様は①③､17連/ﾄﾚｲ仕様/切替仕様は②を取付ける",
"③は左右17連交換台車仕様の時取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6609",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "交換台車支持部連結(OP:17連/17連交換台車仕様)",
"WorkItems": [
"1. PLATE をBOLT WASHER で取付ける",
"2. COVER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20",
"ToolOther": "194cN･m",
"WorkName": "交換台車支持部連結(OP:17連/17連交換台車仕様)",
"WorkItems": [
"1. PLATE をBOLT WASHER で取付ける",
"2. COVER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付①(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1. PLATE ②PLATE ⑦をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"下当てで取付ける",
"PLATE ⑦はﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様時の取付部品",
"②を下当てで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付②(OP:17連交換台車/ﾄﾚｲ仕様)",
"WorkItems": [
"1. PLATE ②PLATE ⑦をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"下当てで取付ける",
"PLATE ⑦はﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様時の取付部品",
"②を下当てで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付②(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1.COVER COVER をSCREW ､COVER COVER をSCREW で取付ける"
],
"WorkPoints": [
"COVER COVER SCREW はﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様時の取付部品",
"COVER COVER は長い方を下側に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付②(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1.COVER COVER をSCREW ､COVER COVER をSCREW で取付ける"
],
"WorkPoints": [
"COVER COVER SCREW はﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様時の取付部品",
"COVER COVER は長い方を下側に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ連結部ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6396",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6396",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ連結部ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6396",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様/切替仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6396",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ連結部ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6396",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰ連結部取付⑤(OP:17連交換台車/ﾄﾚｲ仕様)",
"WorkItems": [
"1. BRACKET BRACKET をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET を㉘治具に当付け固定する",
"ﾌﾞﾗｹｯﾄを治具に当てつける事",
"～手順～１：㉘の右記ボルトを緩める２：交換台車支持部に治具を当付け固定する３：ボルトを締付ける（右記はトレイ仕様時）４：手順１のボルトを締付ける",
"手順1手順4",
"手順2",
"手順3(ﾄﾚｲ仕様)",
"手順3(台車仕様)",
"交換台車支持部に㉘を取付け",
"取付ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6396",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "交換台車支持部取付(OP:17連交換台車支持部切替仕様)",
"WorkItems": [
"◆1. ①を付属ﾎﾞﾙﾄで取付ける",
"2. ②は次工程へ払い出す(同搬物として出荷する)"
],
"WorkPoints": [
"㉘治具に①をセットし架台へドッキングする事",
"①をﾋﾟﾝに挿入する",
"㉘乗せ込み治具を使用し本体に取付ける",
"②は次工程へ払い出し",
"重量物",
"①切替仕様の時は付属ﾎﾞﾙﾄを締付け",
"①ﾋﾟﾝ位置"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車支持部取付ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6609",
"WorkName": "交換台車支持部取付(OP:17連交換台車支持部切替仕様)",
"WorkItems": [
"◆1. ①を付属ﾎﾞﾙﾄで取付ける",
"2. ②は次工程へ払い出す(同搬物として出荷する)"
],
"WorkPoints": [
"㉘治具に①をセットし架台へドッキングする事",
"①をﾋﾟﾝに挿入する",
"㉘乗せ込み治具を使用し本体に取付ける",
"②は次工程へ払い出し",
"重量物",
"①切替仕様の時は付属ﾎﾞﾙﾄを締付け",
"①ﾋﾟﾝ位置"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6609",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車位置決め基準平行出し治具(34連用)",
"Size": "",
"ToolOther": "FM-6075",
"WorkName": "交換台車平行調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"2. ﾍｯﾄﾞﾌﾟﾚｰﾄに㉘を取付け、ﾀﾞｲﾔﾙｹﾞｰｼﾞを測定位置に当付ける",
"1. 交換台車駆動部(右側)に平行出し治具を取付ける",
"3. X軸を移動させ規格値内になる様､平行調整ﾎﾞﾙﾄにて調整する"
],
"WorkPoints": [
"奥側へ押し当てる事",
"平行調整ﾎﾞﾙﾄ",
"平行度:±0.05mm以内",
"※支持部側を基準とし､駆動部側を測定",
"ヘッドプレートに㉗を取付、㉘をセットする",
"平行度:±0.05mm以内",
"ﾄﾚｲ仕様時は実施不要",
"※支持部側を基準とし､駆動部側を調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"調整側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6075",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ部ﾏｸﾞﾈｯﾄｽﾀﾝﾄﾞ取付治具",
"Size": "",
"ToolOther": "FM-2898",
"WorkName": "交換台車平行調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [],
"WorkPoints": [
"平行調整ﾎﾞﾙﾄ",
"平行度:±0.05mm以内",
"※支持部側を基準とし､駆動部側を測定",
"ヘッドプレートに㉗を取付、㉘をセットする",
"平行調整ﾎﾞﾙﾄ",
"平行度:±0.05mm以内",
"※支持部側を基準とし､駆動部側を測定",
"ヘッドプレートに㉗を取付、㉘をセットする",
"平行度:±0.05mm以内",
"ﾄﾚｲ仕様時は実施不要",
"※支持部側を基準とし､駆動部側を調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2898",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "交換台車平行調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [],
"WorkPoints": [
"平行調整ﾎﾞﾙﾄ",
"平行度:±0.05mm以内",
"※支持部側を基準とし､駆動部側を測定",
"ヘッドプレートに㉗を取付、㉘をセットする",
"平行調整ﾎﾞﾙﾄ",
"平行度:±0.05mm以内",
"※支持部側を基準とし､駆動部側を測定",
"ヘッドプレートに㉗を取付、㉘をセットする",
"平行度:±0.05mm以内",
"ﾄﾚｲ仕様時は実施不要",
"※支持部側を基準とし､駆動部側を調整する"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整側",
"WETE-G002-A01"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "±0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車駆動部ｶﾞｲﾄﾞ位置出し治具(17連用)間隔406㎜",
"Size": "",
"ToolOther": "FM-6423",
"WorkName": "交換台車上部ｶﾞｲﾄﾞ調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"1. ｶﾞｲﾄﾞ位置出し治具を取付け基準側ｶﾞｲﾄﾞ(右側)に押し当てる",
"2. ｶﾞｲﾄﾞ位置出し治具にｶﾞﾀﾂｷが無い様に､調整側ｶﾞｲﾄﾞ(左側)を動かして調整する",
"3. ｶﾞｲﾄﾞ位置出し治具を取付け基準側ｶﾞｲﾄﾞ(左側)に押し当てる",
"4. ｶﾞｲﾄﾞ位置出し治具にｶﾞﾀﾂｷが無い様に､調整側ｶﾞｲﾄﾞ(右側)を動かして調整する"
],
"WorkPoints": [
"規格値:406㎜±0.2㎜",
"ﾄﾚｲ仕様時は実施不要",
"㉙で隙間を確認し、㉙が入ら無い事",
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部切替仕様ﾄﾚｲﾌｨｰﾀﾞｰ仕様",
"17連交換台車駆動部切替仕様",
"㉙で隙間を確認し、㉙が入ら無い事",
"㉚のプレートが支持部側になる様治具を設置する事",
"㉚台車駆動部ｶﾞｲﾄﾞ位置出し治具(切替仕様)間隔406mm",
"㉚のブロックが支持部側になる様治具を設置する事",
"切替仕様時は㉚でガイド調整"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:11.交換台車対応ﾕﾆｯﾄ ｶﾞｲﾄﾞの幅確認(X位置確認)",
"検査表①:11.交換台車対応ﾕﾆｯﾄ ｶﾞｲﾄﾞの幅確認(X位置確認)",
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6423",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "台車駆動部ｶﾞｲﾄﾞ位置出し治具(切替仕様)間隔406㎜",
"Size": "",
"ToolOther": "FM-6654",
"WorkName": "交換台車上部ｶﾞｲﾄﾞ調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"1. ｶﾞｲﾄﾞ位置出し治具を取付け基準側ｶﾞｲﾄﾞ(右側)に押し当てる",
"2. ｶﾞｲﾄﾞ位置出し治具にｶﾞﾀﾂｷが無い様に､調整側ｶﾞｲﾄﾞ(左側)を動かして調整する",
"3. ｶﾞｲﾄﾞ位置出し治具を取付け基準側ｶﾞｲﾄﾞ(左側)に押し当てる",
"4. ｶﾞｲﾄﾞ位置出し治具にｶﾞﾀﾂｷが無い様に､調整側ｶﾞｲﾄﾞ(右側)を動かして調整する"
],
"WorkPoints": [
"規格値:406㎜±0.2㎜",
"ﾄﾚｲ仕様時は実施不要",
"㉙で隙間を確認し、㉙が入ら無い事",
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部切替仕様ﾄﾚｲﾌｨｰﾀﾞｰ仕様",
"17連交換台車駆動部切替仕様",
"㉙で隙間を確認し、㉙が入ら無い事",
"㉚のプレートが支持部側になる様治具を設置する事",
"㉚台車駆動部ｶﾞｲﾄﾞ位置出し治具(切替仕様)間隔406mm",
"㉚のブロックが支持部側になる様治具を設置する事",
"切替仕様時は㉚でガイド調整"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:11.交換台車対応ﾕﾆｯﾄ ｶﾞｲﾄﾞの幅確認(X位置確認)",
"検査表①:11.交換台車対応ﾕﾆｯﾄ ｶﾞｲﾄﾞの幅確認(X位置確認)",
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6654",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "交換台車上部ｶﾞｲﾄﾞ調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [],
"WorkPoints": [
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部切替仕様ﾄﾚｲﾌｨｰﾀﾞｰ仕様",
"規格値:406㎜±0.2㎜",
"ﾄﾚｲ仕様時は実施不要"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "交換台車上部ｶﾞｲﾄﾞ調整(OP:17連交換台車仕様、ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [],
"WorkPoints": [
"17連交換台車駆動部仕様",
"規格値:406㎜±0.2㎜",
"17連交換台車駆動部切替仕様ﾄﾚｲﾌｨｰﾀﾞｰ仕様",
"規格値:406㎜±0.2㎜",
"ﾄﾚｲ仕様時は実施不要"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "幅寄せﾓｰﾀ取付・整線(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.0N･m",
"WorkName": "幅寄せﾓｰﾀ取付・整線(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "幅寄せﾓｰﾀ取付・整線(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "9.8N･m",
"WorkName": "交換台車対応前面ｶﾊﾞｰ部(ﾘｱ)取付(OP:30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER WASHER で取付ける",
"2. ⑥をBOLT WASHER ㉒で取付ける",
"1. ①をBOLT WASHER WASHER で取付ける",
"2. ⑥をBOLT WASHER ㉒で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "交換台車対応前面ｶﾊﾞｰ部(ﾘｱ)取付(OP:30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER WASHER で取付ける",
"2. ⑥をBOLT WASHER ㉒で取付ける",
"1. ①をBOLT WASHER WASHER で取付ける",
"2. ⑥をBOLT WASHER ㉒で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける",
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける",
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付ﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"標準仕様(切り欠き無し)",
"LCRﾁｪｯｶｰ仕様(切り欠き有り)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押し付け",
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T25",
"ToolOther": "6.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰﾓｰﾀｰと配線が干渉し無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Rear"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"注意:切替仕様の台車ﾀｲﾌﾟの時のみ取付",
"③のｷｰを本体側安全SWに干渉無く接続する",
"ｺﾈｸﾀ名称:S313/4R",
"ｺﾝﾍﾞﾔｰﾓｰﾀｰと配線が干渉し無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Rear"
],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰﾓｰﾀｰと配線が干渉し無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Rear"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾘｱ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰﾓｰﾀｰと配線が干渉し無い事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Rear"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"2ｹずつ(ﾃﾞｭｱﾙ時)",
"一括交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【一括交換式】",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x300)",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051685AA x2下受けﾌﾞﾛｯｸ一括交換_ﾃﾞｭｱﾙ(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA051681AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ_NPM-GW"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙﾚｰﾝ専用仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時)",
"一括交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"■MTKA052577AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用_NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用",
"(760x300)",
"【一括交換式】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ｼﾝｸﾞﾙ時)",
"一括交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ｼﾝｸﾞﾙｺﾝﾍﾞｱ",
"【一括交換式】",
"GWｼﾝｸﾞﾙRear専用",
"GWｼﾝｸﾞﾙRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051741AA x1下受けﾌﾞﾛｯｸ一括交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051742AA x2下受けﾌﾞﾛｯｸ一括交換_ｼﾝｸﾞﾙ(Rear):NPM-GW",
"(760x687)",
"687mm対応",
"687mm対応"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260㎜)仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"2ｹずつ(ﾃﾞｭｱﾙ時)",
"一括交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ",
"【一括交換式】",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x260)",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"■MTKA052879AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA052877AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260mm)_NPM-GW"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用(260㎜)仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用(260mm))",
"一括交換_ﾌﾛﾝﾄ用3D図※搭載場所はﾘｱ",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"■MTKA052578AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用(260mm)_NPM-GW",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用",
"(760x260)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"2ｹずつ(ﾃﾞｭｱﾙ時)",
"自動交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【自動交換式】",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051800AA x2下受けﾌﾞﾛｯｸ自動交換(Front):NPM-GW",
"■MTKA051809AA x2下受けﾌﾞﾛｯｸ自動交換_ﾃﾞｭｱﾙ(Rear):NPM-GW",
"奥側装着",
"■MTKA051852AA x1下受けﾌﾞﾛｯｸ自動交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時(760x300)",
"奥側装着"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ｼﾝｸﾞﾙ時)",
"自動交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ｼﾝｸﾞﾙｺﾝﾍﾞｱ",
"【自動交換式】",
"GWｼﾝｸﾞﾙRear専用",
"GWｼﾝｸﾞﾙRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051800AA x2下受けﾌﾞﾛｯｸ自動交換(Front):NPM-GW",
"■MTKA051836AA x2下受けﾌﾞﾛｯｸ自動交換_ｼﾝｸﾞﾙ(Rear):NPM-GW",
"■MTKA051854AA x1下受けﾌﾞﾛｯｸ自動交換_ ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"(760x687)",
"687mm対応",
"687mm対応"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260㎜)仕様)ﾘｱ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"2ｹずつ(ﾃﾞｭｱﾙﾚｰﾝ時)",
"自動交換_ﾘｱ用3D図",
"搭載箇所(ﾘｱ)",
"搭載箇所(ﾘｱ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【自動交換式】",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051860AA x2下受けﾌﾞﾛｯｸ自動交換_260mm(Front):NPM-GW",
"■MTKA051862AA x2下受けﾌﾞﾛｯｸ自動交換_260mm(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA052581AA x1下受けﾌﾞﾛｯｸ自動交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260mm)_NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x260)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ、廃棄BOX(ﾘｱ)取付",
"WorkItems": [
"1. 廃棄BOX(①)及びﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(②or③or④)を取付ける"
],
"WorkPoints": [
"仕様を確認し､搭載する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"or",
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車/ﾄﾚｲﾌｨｰﾀﾞ連結部仕様)",
"WorkItems": [
"1. 架台へPLUG を取付ける"
],
"WorkPoints": [
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所",
"PLUG を架台に下記指示通り取付",
"PLUG 取付位置は供給部仕様で変わるので注意する",
"ﾄﾚｲﾌｨｰﾀﾞ連結部(本体側/F､R側)M10用×2個",
"右側は前工程で取付済み"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:17連交換台車、30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①は下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記は交換台車仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:ﾄﾚｲ、切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記はﾄﾚｲ､切替仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:17連交換台車、30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記は交換台車仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:ﾄﾚｲ、切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①は仕様で形が変わるので注意する(下記はﾄﾚｲ､切替仕様)",
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)①",
"WorkItems": [
"1. ①をSCREW で仮付けする"
],
"WorkPoints": [
"SCREW 取付箇所詳細(交換台車仕様)",
"SCREW 取付箇所詳細(交換台車仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"仮止め:SD-EJM2FH1-323にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)②",
"WorkItems": [
"■1. ①をSCREW SCREW WASHER で仮止めする"
],
"WorkPoints": [
"同一ﾛｯﾄNo.のこと",
"開閉ｶﾊﾞｰSWのﾛｯﾄNo.と合わせる事",
"①の下にWASHER をいれSCREW で仮止めする※交換台車仕様",
"SCREW は下から取付ける"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:開閉ｶﾊﾞｰ&ﾌｨｰﾀﾞｰｶﾊﾞｰ安全SWのﾍﾟｱ確認"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"仮止め:SD-EJM2FH1-323にて本締め",
"設備下",
"WETE-G002-A01"
]
} | {
"QualityItem": "ﾛｯﾄ№確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ№が同一である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.50㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟み固定する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾚﾊﾞｰ動作時ﾌｨｰﾀﾞｰｶﾊﾞｰと干渉が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"･ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾚﾊﾞｰ動作時ﾌｨｰﾀﾞｰｶﾊﾞｰと干渉が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"･ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①ｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は開閉ｶﾊﾞｰとﾚﾊﾞｰとの隙間を調整する",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"設備下",
"設備下",
"設備下",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①ｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は開閉ｶﾊﾞｰとﾚﾊﾞｰとの隙間を調整する",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"設備下",
"設備下",
"設備下",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)①",
"WorkItems": [
"1. ①をSCREW で仮付けする"
],
"WorkPoints": [
"SCREW 取付箇所詳細(ﾄﾚｲ仕様)",
"SCREW 取付箇所詳細(ﾄﾚｲ仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"仮止め:SD-EJM2FH1-328にて本締め",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)②",
"WorkItems": [
"■1. ①をSCREW SCREW WASHER で仮止めする"
],
"WorkPoints": [
"同一ﾛｯﾄNo.のこと",
"開閉ｶﾊﾞｰSWのﾛｯﾄNo.と合わせる事",
"①をSCREW SCREW WASHER で仮付けする※ﾄﾚｲ仕様時､切替仕様",
"SCREW は下から取付ける"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:開閉ｶﾊﾞｰ&ﾌｨｰﾀﾞｰｶﾊﾞｰ安全SWのﾍﾟｱ確認"
],
"WorkTypes": [],
"Words": [
"仮止め:SD-EJM2FH1-328にて本締め",
"設備下",
"ﾘｱ",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)",
"WETE-G002-A01"
]
} | {
"QualityItem": "ﾛｯﾄ№確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ№が同一である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.50㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｱ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟み固定する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"･ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"･ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①のｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は下から取付ける",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する",
"SCREW は開閉ｶﾊﾞｰとﾚﾊﾞｰとの隙間を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"設備下",
"設備下",
"設備下",
"ﾘｱ",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①のｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は下から取付ける",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する",
"SCREW は開閉ｶﾊﾞｰとﾚﾊﾞｰとの隙間を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"設備下",
"設備下",
"設備下",
"ﾘｱ",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "【NPM-GW専用】ｼﾘｱﾙﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. ①のﾗﾍﾞﾙを貼付ける"
],
"WorkPoints": [
"ﾘｱ側",
"貼る部分㉗で脱脂する事",
"ﾗﾍﾞﾙに気泡が入らないように貼付ける事",
"ﾗﾍﾞﾙの表記に間違え､位置ｽﾞﾚが無い事を確認する",
"15±0.5㎜",
"貼付け寸法は右記の平らな面からの寸法にする事",
"10±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立①",
"WorkItems": [
"1. BRACKET に⑥を流用ﾈｼﾞで取付ける"
],
"WorkPoints": [
"ﾊﾞｰﾘﾝｸﾞ面に取付ける事",
"ｾﾝｻｰ配線の向きに注意する事",
"ﾊﾞｰﾘﾝｸﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1046/1900TR",
"B1046/1900R"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立②",
"WorkItems": [
"1. ①へ②をSCREW で取付ける",
"2. 配線を引き回､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"目視ﾚﾍﾞﾙで長穴ｾﾝﾀｰに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1046/1900TR",
"B1900/1R",
"B1900/1TR",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立②",
"WorkItems": [
"1. ①へ②をSCREW で取付ける",
"2. 配線を引き回､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"目視ﾚﾍﾞﾙで長穴ｾﾝﾀｰに取付",
"ｺﾈｸﾀ接続確認"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:2.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B1046/1900TR",
"B1046/1900R",
"B1900/1R",
"B1900/1TR",
"ﾌﾛﾝﾄ",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "81cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立③(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①へCOVER をBOLT で取付ける"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-337にて本締め"
],
"Tolks": [
"締付ﾄﾙｸ 81cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "81cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "81cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立③(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①へCOVER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 81cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "81cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立④",
"WorkItems": [
"1. 本体フレームのアイボルト取付穴に㉖を取付ける",
"2. ㉖治具にＧＷ専用のブロックを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"右側面",
"㉖ＧＷ専用ブロックは上当付けでノブで取付ける",
"ﾌﾛﾝﾄ",
"㉖ノブを回し、上方向に最大まで上昇させる。"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事",
"ﾌﾛﾝﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑥(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ300㎜仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で取付ける"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-344にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"PLATE は切り欠き側を固定する(300㎜対応)",
"PLATE は切り欠き側を固定する(300㎜対応)",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"ﾌﾛﾝﾄ",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑥(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で取付ける"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-345にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"PLATE は切り欠き側を固定する(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ対応)",
"PLATE 設置時はﾚｰﾙを最大幅にしておく",
"PLATE は切り欠き側を固定する(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ対応)",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"ﾌﾛﾝﾄ",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑥(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ260㎜仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で仮止め"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-344にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾌﾛﾝﾄ",
"PLATE は切り欠き無しを固定する(260㎜対応)",
"PLATE は切り欠き無しを固定する(260㎜対応)",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑦(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長コンベアーに㉖を仮止め、クランププレートを調整する"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ固定ﾎﾞﾙﾄで調整する",
"仮止め:SD-EJM8EH1-344にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"クランププレートを㉖に押し当て",
"クランププレートを㉖に押し当て",
"ﾌﾛﾝﾄ",
"当付け箇所",
"当付け箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑦(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長コンベアーに㉖を仮止め、クランププレートを調整する"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ固定ﾎﾞﾙﾄで調整する",
"仮止め:SD-EJM8EH1-345にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"当付け箇所",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"クランププレートを㉖に押し当て",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.30㎜",
"ToolOther": "通り側",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整"
],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"ﾌﾛﾝﾄ",
"WETE-G002-A03"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5±0.2㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "0.8N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.30㎜",
"ToolOther": "通り側",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整"
],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾌﾛﾝﾄ",
"WETE-G002-A03"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5±0.2㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.