Datasets:
ayuzawa
/
ManageProcess20

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
222
3.65k
output
stringlengths
193
367
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立2", "WorkItems": [ "1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂", "2. ②を①に貼付" ], "WorkPoints": [ "FM-5804", "FM-5804", "矢印方向に当てつけ", "貼付け後､手で仮圧着", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす", "治具番号1", "治具番号1" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5890", "WorkName": "開閉ｶﾊﾞｰ組立2", "WorkItems": [ "3. ①のアクリルシートをめくり㉙でとめ、脱脂", "4. COVER にTAPE を貼付ける" ], "WorkPoints": [ "圧着ﾛｰﾗｰで2往復", "2本", "2本" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "15㎜", "50㎜", "70㎜", "50㎜", "50㎜" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5890", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "NPM-GH用扉組立台", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立3", "WorkItems": [ "1. ①に治具をｾｯﾄし②を貼付" ], "WorkPoints": [ "治具は上側に押当", "FM-5804", "FM-5804", "穴位置を合わせた後貼付けし､手で仮圧着", "治具は上側に押当" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号左1", "治具番号左2", "治具番号右3", "治具番号右4" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立3", "WorkItems": [ "1. ①に治具をｾｯﾄし②を貼付" ], "WorkPoints": [ "治具は上側に押当", "FM-5804", "FM-5804", "穴位置を合わせた後貼付けし､手で仮圧着", "治具は上側に押当" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号左1", "治具番号左2", "治具番号右3", "治具番号右4" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "6.0N･m", "WorkName": "開閉ｶﾊﾞｰ組立4", "WorkItems": [ "2. 本締めする", "1. ①にPULL をBOLT WASHER WASHER で取付" ], "WorkPoints": [ "内側" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m", "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "3.2N･m", "WorkName": "開閉ｶﾊﾞｰ組立4", "WorkItems": [ "2. 本締めする", "1. ①にPULL をBOLT WASHER WASHER で取付" ], "WorkPoints": [ "内側" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m", "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "NPM-GH用扉組立台", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立5", "WorkItems": [ "3. 2完成品にCOVER を貼付", "1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)" ], "WorkPoints": [ "FM-5804", "FM-5804" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立5", "WorkItems": [ "3. 2完成品にCOVER を貼付", "1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)" ], "WorkPoints": [ "FM-5804", "FM-5804" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "1.2㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立5", "WorkItems": [], "WorkPoints": [ "端面が合っている事", "FM-5804", "治具に押し当てながら貼付ける", "貼付け後､手で仮圧着", "真ん中を目安に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.2mm" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "作業指示通り出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "NPM-GH用扉組立台", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立6", "WorkItems": [ "1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. ②のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめる", "3.2完成品に②を貼付け" ], "WorkPoints": [ "FM-5804", "FM-5804", "FM-5804", "治具に押し当てながら貼付", "貼付け後､手で仮圧着" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号4", "治具番号5", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立6", "WorkItems": [ "1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. ②のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめる", "3.2完成品に②を貼付け" ], "WorkPoints": [ "FM-5804", "FM-5804", "FM-5804", "治具に押し当てながら貼付", "貼付け後､手で仮圧着" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号4", "治具番号5", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "NPM-GH用扉組立台", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立7", "WorkItems": [], "WorkPoints": [ "FM-5804", "隙間が無い事", "端面が合っている事", "治具2,3を先に取付ける", "圧着ﾛｰﾗｰで2往復", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号2" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立7", "WorkItems": [], "WorkPoints": [ "FM-5804", "隙間が無い事", "端面が合っている事", "治具2,3を先に取付ける", "圧着ﾛｰﾗｰで2往復", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号2" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ", "Size": "5kg", "ToolOther": "FM-5890", "WorkName": "開閉ｶﾊﾞｰ組立7", "WorkItems": [ "1. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. 1完成品に②を貼付け圧着" ], "WorkPoints": [ "両ｻｲﾄﾞの治具に沿わせながら貼付", "FM-5804", "FM-5804" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号3", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5890", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "NPM-GH用扉組立台", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立8", "WorkItems": [ "5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す", "4. ①に②③を貼付け圧着", "3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)", "1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂" ], "WorkPoints": [ "治具に押し当てながら貼付", "隙間目安0.5mm", "段差目安1.2mm", "②を貼り終えてから③を貼る", "圧着ﾛｰﾗｰで2往復する", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号3", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾞｱ組立台(NPM-GH用)", "Size": "", "ToolOther": "FM-5804", "WorkName": "開閉ｶﾊﾞｰ組立8", "WorkItems": [ "5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す", "4. ①に②③を貼付け圧着", "3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)", "1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂" ], "WorkPoints": [ "治具に押し当てながら貼付", "隙間目安0.5mm", "段差目安1.2mm", "②を貼り終えてから③を貼る", "圧着ﾛｰﾗｰで2往復する", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号3", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5804", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ", "Size": "5kg", "ToolOther": "FM-5890", "WorkName": "開閉ｶﾊﾞｰ組立8", "WorkItems": [ "5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す", "4. ①に②③を貼付け圧着", "3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)", "1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂" ], "WorkPoints": [ "治具に押し当てながら貼付", "隙間目安0.5mm", "段差目安1.2mm", "②を貼り終えてから③を貼る", "圧着ﾛｰﾗｰで2往復する", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号3", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "FM-5890", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立8", "WorkItems": [ "5. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す", "4. ①に②③を貼付け圧着", "3. 治具台に①をｾｯﾄし､専用治具を取付け脱脂", "2. SPRING-PLATE を取付(挟み込む)", "1. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂" ], "WorkPoints": [ "治具に押し当てながら貼付", "隙間目安0.5mm", "段差目安1.2mm", "②を貼り終えてから③を貼る", "圧着ﾛｰﾗｰで2往復する", "圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "治具番号3", "この作業では同じものを2個製作" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入", "◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布", "3. COVER にBUSH を取付", "■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付" ], "WorkPoints": [ "付属波ﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属波ﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "取付方向に注意する事", "取付方向に注意する事" ], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [ "検査表GAS-SPRING :4.型式確認と製造ﾛｯﾄNo.記録" ], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 小豆:1", "ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1", "検査表GAS-SPRING :2.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ", "この作業では同じものを2個製作", "WEPJ-G002-C11" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "3. COVER にBUSH を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表GAS-SPRING :4.型式確認と製造ﾛｯﾄNo.記録", "検査表GAS-SPRING :2.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ", "■安全作業", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入", "◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布", "■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付" ], "WorkPoints": [ "付属波ﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属波ﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "取付方向に注意する事", "取付方向に注意する事" ], "Tolks": [], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 小豆:1", "ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1", "この作業では同じものを2個製作", "■安全作業", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入", "◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布", "3. COVER にBUSH を取付", "■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付", "5. 4完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "端面を合わせる", "取付け方向に注意する事", "取付け方向に注意する事", "付属波ﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属波ﾜｯｼｬｰ" ], "Tolks": [ "締付ﾄﾙｸ 20N･m", "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [ "検査表GAS-SPRING :4.型式確認と製造ﾛｯﾄNo.記録" ], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 小豆:1", "ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1", "検査表GAS-SPRING :2.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ", "この作業では同じものを2個製作", "WEPJ-G002-C11" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "3. COVER にBUSH を取付" ], "WorkPoints": [ "端面を合わせる", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属波ﾜｯｼｬｰ" ], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表GAS-SPRING :2.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ", "■安全作業", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "20N･m", "WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入", "◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布", "■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付" ], "WorkPoints": [ "付属ﾌｪﾉｰﾙﾜｯｼｬｰ" ], "Tolks": [], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表GAS-SPRING :4.型式確認と製造ﾛｯﾄNo.記録", "ｸﾞﾘｰｽ塗布 小豆:1", "ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1", "この作業では同じものを2個製作", "■安全作業", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "20N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)", "WorkItems": [ "3. COVER にBUSH を取付" ], "WorkPoints": [ "端面を合わせる", "付属ﾌｪﾉｰﾙﾜｯｼｬｰ", "付属波ﾜｯｼｬｰ" ], "Tolks": [ "締付ﾄﾙｸ 20N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表GAS-SPRING :2.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ", "■安全作業", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "開閉ｶﾊﾞｰ組立11(ﾋﾝｼﾞ組立)", "WorkItems": [ "3. HINGE を再度組立", "◆1. HINGE の青枠線内にｸﾞﾘｰｽを塗布" ], "WorkPoints": [ "組み合わせ方向･ﾋﾟﾝ挿入方向に注意<下図参照>" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "取付け方向に注意!この部品には方向性があります", "この作業では同じものを4個製作", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)", "WorkItems": [ "2. ｲﾝｼｭﾛｯｸで配線を固定", "3. 2完成品を脱脂後､LABEL を貼付", "1. BRACKET にSWITCH をBOLT NUT で取付" ], "WorkPoints": [ "裏面", "開閉ｶﾊﾞｰSWのF側･R側で銘板を貼付け", "BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､ﾛｯﾄNOを(F側･R側)合わせる事", "型式表示が上を向くように", "ﾌｨｰﾀﾞｶﾊﾞｰ用SW組立で未使用の開閉ｶﾊﾞｰ用SWを使用", "ﾅｯﾄ側も同等のﾄﾙｸで締付けの事" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m", "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "取付け方向に注意!この部品には方向性があります", "2mm", "1mm", "この作業では同じものを2個製作", "WEPJ-G002-C11" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "100cN･m", "WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)", "WorkItems": [ "2. ｲﾝｼｭﾛｯｸで配線を固定", "1. BRACKET にSWITCH をBOLT NUT で取付" ], "WorkPoints": [ "BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､ﾛｯﾄNOを(F側･R側)合わせる事", "ﾅｯﾄ側も同等のﾄﾙｸで締付けの事" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m", "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "取付け方向に注意!この部品には方向性があります", "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "7ﾎﾞｯｸｽﾋﾞｯﾄ", "ToolOther": "100cN･m", "WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)", "WorkItems": [ "2. ｲﾝｼｭﾛｯｸで配線を固定", "1. BRACKET にSWITCH をBOLT NUT で取付" ], "WorkPoints": [ "BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､ﾛｯﾄNOを(F側･R側)合わせる事", "ﾅｯﾄ側も同等のﾄﾙｸで締付けの事" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m", "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "取付け方向に注意!この部品には方向性があります", "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)", "WorkItems": [ "3. 2完成品を脱脂後､LABEL を貼付" ], "WorkPoints": [ "裏面", "開閉ｶﾊﾞｰSWのF側･R側で銘板を貼付け", "型式表示が上を向くように", "ﾌｨｰﾀﾞｶﾊﾞｰ用SW組立で未使用の開閉ｶﾊﾞｰ用SWを使用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "2mm", "1mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "T20", "ToolOther": "194cN･m", "WorkName": "開閉ｶﾊﾞｰ組立13", "WorkItems": [ "2. 1完成品にCABLE またはCABLE を挿入", "4. ②を①にBOLT WASHER で固定" ], "WorkPoints": [ "治具をあてつける", "矢印の方向から挿入", "FRONT側:S311R1REAR側;S312R1", "確認の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "開閉ｶﾊﾞｰ安全SW調整治具(Gｼﾘｰｽﾞ)", "Size": "", "ToolOther": "FM-6034", "WorkName": "開閉ｶﾊﾞｰ組立13", "WorkItems": [ "2. 1完成品にCABLE またはCABLE を挿入", "4. ②を①にBOLT WASHER で固定" ], "WorkPoints": [ "治具をあてつける", "矢印の方向から挿入", "FRONT側:S311R1REAR側;S312R1", "確認の事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6034", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立13", "WorkItems": [ "1. ①にBUSH を取付", "2. 1完成品にCABLE またはCABLE を挿入", "3. 2完成品の配線と②の配線を接続し､ｲﾝｼｭﾛｯｸで固定", "4. ②を①にBOLT WASHER で固定" ], "WorkPoints": [ "治具をあてつける", "矢印の方向から挿入", "FRONT側:S311R1REAR側;S312R1", "確認の事", "治具の挿入隙間を確保する事", "F側とR側を区別する事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "この作業では同じものを2個製作", "WEPJ-G002-D06" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立14", "WorkItems": [ "1. ①の配線をｲﾝｼｭﾛｯｸで固定", "3 2完成品にRUBBER-CUSHION を取付", "2. 1完成品に黄色ﾏｰｷﾝｸﾞ" ], "WorkPoints": [ "ｲﾝｼｭﾛｯｸと配線の位置関係", "ｲﾝｼｭﾛｯｸが配線の下側にくる事", "左右に取付け", "ﾌﾚｰﾑ内に通す", "ｲﾝｼｭﾛｯｸの(頭)方向は内側のこと" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "70mm", "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立14", "WorkItems": [ "3 2完成品にRUBBER-CUSHION を取付", "2. 1完成品に黄色ﾏｰｷﾝｸﾞ" ], "WorkPoints": [ "ｲﾝｼｭﾛｯｸと配線の位置関係", "ｲﾝｼｭﾛｯｸが配線の下側にくる事", "左右に取付け", "ﾌﾚｰﾑ内に通す", "ｲﾝｼｭﾛｯｸの(頭)方向は内側のこと" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "70mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1.0㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "6.0N･m", "WorkName": "開閉ｶﾊﾞｰ組立15(ﾀﾞﾝﾊﾟｰ取付け)", "WorkItems": [ "1. ②③にｸｯｼｮﾝ材を巻く", "2. ①に1完成品をWASHER BOLT で取付" ], "WorkPoints": [ "取付目安1.25mm", "矢印方向に押し当てて取付", "取付場所2か所あり" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立15(ﾀﾞﾝﾊﾟｰ取付け)", "WorkItems": [ "1. ②③にｸｯｼｮﾝ材を巻く", "2. ①に1完成品をWASHER BOLT で取付" ], "WorkPoints": [ "取付目安1.25mm", "矢印方向に押し当てて取付", "取付場所2か所あり" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "6㎜", "ToolOther": "9.8N･m", "WorkName": "開閉ｶﾊﾞｰ組立16", "WorkItems": [ "1. ①に②PLATE をBOLT WASHER で取付", "2. 1完成品にMAGNET をSCREW で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 9.8N･m", "締付ﾄﾙｸ 90cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "90cN･m", "WorkName": "開閉ｶﾊﾞｰ組立16", "WorkItems": [], "WorkPoints": [ "面位置に合わす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.8㎜" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "1.8㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰ組立16", "WorkItems": [ "1. ①に②PLATE をBOLT WASHER で取付", "2. 1完成品にMAGNET をSCREW で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 9.8N･m", "締付ﾄﾙｸ 90cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付位置確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "作業指示通り出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｶﾊﾞｰﾗﾍﾞﾙ貼付け", "WorkItems": [ "1. ①を脱脂", "2. 1完成品にLABEL LABEL LABEL を貼付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(開閉ｶﾊﾞｰ)", "Size": "", "ToolOther": "FM-6870", "WorkName": "識別ﾗﾍﾞﾙ貼付け17連/34連(前側)", "WorkItems": [ "2. 1完成品に㉗を取付けLABEL を貼付け" ], "WorkPoints": [ "脱脂箇所", "裏面㉗取付け規制位置" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付け確認", "ToolManageNo": "FM-6870", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(開閉ｶﾊﾞｰ)", "Size": "", "ToolOther": "FM-6870", "WorkName": "識別ﾗﾍﾞﾙ貼付け17連/34連・T/C切替(後側)", "WorkItems": [ "1. ①を脱脂" ], "WorkPoints": [ "脱脂箇所" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付け確認", "ToolManageNo": "FM-6870", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.2N･m", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1", "WorkItems": [ "1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付" ], "WorkPoints": [ "内曲げが取付け面になるように", "ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付", "ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで直角より､小さく曲げてから取付ける事", "目安としてﾋﾝｼﾞからの出しろが1mmになるように", "直角より大きい曲げは NG本体工程で､取付不可", "直角より､小さく曲げる目視(参考)" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1", "WorkItems": [ "1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付" ], "WorkPoints": [ "内曲げが取付け面になるように", "ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付", "ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで直角より､小さく曲げてから取付ける事", "目安としてﾋﾝｼﾞからの出しろが1mmになるように", "直角より大きい曲げは NG本体工程で､取付不可", "直角より､小さく曲げる目視(参考)" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2", "WorkItems": [ "■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入", "3. MONITOR に①をBOLT WASHER で取付", "■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入" ], "WorkPoints": [ "裏側", "ﾓﾆﾀと平行に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ2.0N･m" ], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "全てOFFのこと", "OFF", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認", "この作業では同じものを2個製作", "WEPJ-G002-D06" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2", "WorkItems": [ "■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入", "3. MONITOR に①をBOLT WASHER で取付", "■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入" ], "WorkPoints": [ "裏側", "ﾓﾆﾀと平行に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ2.0N･m" ], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認" ], "WorkTypes": [], "Words": [ "全てOFFのこと", "OFF", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ", "この作業では同じものを2個製作", "WEPJ-G002-D06" ] }
{ "QualityItem": "検査書有無確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の有無を確認する", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2", "WorkItems": [ "■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入", "3. MONITOR に①をBOLT WASHER で取付", "■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入" ], "WorkPoints": [ "裏側", "ﾓﾆﾀと平行に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "全てOFFのこと", "OFF", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認", "この作業では同じものを2個製作", "WEPJ-G002-D06" ] }
{ "QualityItem": "設定確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "全てOFFの事", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "2.0N･m", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2", "WorkItems": [ "■2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入", "3. MONITOR に①をBOLT WASHER で取付", "■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入" ], "WorkPoints": [ "裏側", "ﾓﾆﾀと平行に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "全てOFFのこと", "OFF", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ", "検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認", "この作業では同じものを2個製作", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立3", "WorkItems": [ "1. COVER にLABEL LABEL を貼付", "2. 1.の完成品にBUSH を取付", "1. COVER にLABEL LABEL を貼付", "2. 1.の完成品にBUSH を取付", "3. COVER にLABEL を貼付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作", "裏面", "この作業では同じものを2個製作", "裏面", "ACTIVATION", "ACTIVATION", "5mm", "15mm", "50mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "操作ﾊﾟﾈﾙSW組立1", "WorkItems": [ "■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認", "2. ①にSWITCH SWITCH SWITCH SWITCH を取付", "3. ②にSWITCH を取付", "4. 2完成品の裏面にCABLE-SUPPORT を取付" ], "WorkPoints": [ "△ﾏｰｸ", "ｺﾈｸﾀ部", "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "突起がｶﾊﾞｰ側", "F側､R側に区別しておく", "取付後､傾き無き事", "取付け方向は△ﾏｰｸが上になるよう取付", "ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付", "取付け方向は△ﾏｰｸが上になるよう取付" ], "Tolks": [ "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:1.F-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "ACTIVATION", "取付方法", "検査表①:2.R-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "この作業では同じものを2個製作", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "WEPJ-G002-D06" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "操作ﾊﾟﾈﾙSW組立1", "WorkItems": [ "■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認", "2. ①にSWITCH SWITCH SWITCH SWITCH を取付", "3. ②にSWITCH を取付", "4. 2完成品の裏面にCABLE-SUPPORT を取付" ], "WorkPoints": [ "△ﾏｰｸ", "ｺﾈｸﾀ部", "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "突起がｶﾊﾞｰ側", "F側､R側に区別しておく", "取付後､傾き無き事", "取付け方向は△ﾏｰｸが上になるよう取付", "ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付", "取付け方向は△ﾏｰｸが上になるよう取付" ], "Tolks": [ "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:2.R-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "ACTIVATION", "検査表①:1.F-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "取付方法", "この作業では同じものを2個製作", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "WEPJ-G002-D06" ] }
{ "QualityItem": "ｽｲｯﾁ配置確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通りｽｲｯﾁが配置されている事", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5255", "WorkName": "操作ﾊﾟﾈﾙSW組立1", "WorkItems": [ "■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認", "2. ①にSWITCH SWITCH SWITCH SWITCH を取付" ], "WorkPoints": [ "△ﾏｰｸ", "ｺﾈｸﾀ部", "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "突起がｶﾊﾞｰ側", "F側､R側に区別しておく", "取付後､傾き無き事", "取付け方向は△ﾏｰｸが上になるよう取付", "ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付" ], "Tolks": [ "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:1.F-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "取付方法", "検査表①:2.R-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "この作業では同じものを2個製作", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "FM-5255", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "FM-5255専用ﾋﾞｯﾄ", "ToolOther": "147cN･m", "WorkName": "操作ﾊﾟﾈﾙSW組立1", "WorkItems": [ "3. ②にSWITCH を取付", "4. 2完成品の裏面にCABLE-SUPPORT を取付", "■1. SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認", "2. ①にSWITCH SWITCH SWITCH SWITCH を取付" ], "WorkPoints": [ "取付け方向は△ﾏｰｸが上になるよう取付", "△ﾏｰｸ", "ｺﾈｸﾀ部", "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "突起がｶﾊﾞｰ側", "F側､R側に区別しておく", "取付後､傾き無き事", "取付け方向は△ﾏｰｸが上になるよう取付", "ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付" ], "Tolks": [ "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ACTIVATION", "■安全作業", "検査表①:1.F-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "取付方法", "検査表①:2.R-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ", "この作業では同じものを2個製作", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "125cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "操作ﾊﾟﾈﾙSW組立2", "WorkItems": [ "■1. ①②にPANEL SWITCH を取付" ], "WorkPoints": [ "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "SW部", "取付けﾘﾝｸﾞ", "SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる", "ﾊﾟﾈﾙ裏側", "組み合わせに注意(F側･R側)", "SWITCH は1工程前準備より貰い受ける事", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "SW部の凹型とｶﾊﾞｰ部の凸型を合わせる", "SW部とｶﾊﾞｰ部の隙間が均等にする" ], "Tolks": [ "締付ﾄﾙｸ 125cN･m", "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:1.F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "検査表①:2.R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "WEPJ-G002-D06" ] }
{ "QualityItem": "ｽｲｯﾁ配置確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通りｽｲｯﾁが配置されている事", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "非常ｽｲｯﾁ締付工具", "Size": "", "ToolOther": "FM-5254", "WorkName": "操作ﾊﾟﾈﾙSW組立2", "WorkItems": [ "■1. ①②にPANEL SWITCH を取付" ], "WorkPoints": [ "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "SW部", "取付けﾘﾝｸﾞ", "SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる", "ﾊﾟﾈﾙ裏側", "組み合わせに注意(F側･R側)", "SWITCH は1工程前準備より貰い受ける事", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "SW部の凹型とｶﾊﾞｰ部の凸型を合わせる", "SW部とｶﾊﾞｰ部の隙間が均等にする" ], "Tolks": [ "締付ﾄﾙｸ 125cN･m", "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:1.F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:2.R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "FM-5254", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "FM-5254専用ﾋﾞｯﾄ", "ToolOther": "125cN･m", "WorkName": "操作ﾊﾟﾈﾙSW組立2", "WorkItems": [ "■1. ①②にPANEL SWITCH を取付" ], "WorkPoints": [ "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "SW部", "取付けﾘﾝｸﾞ", "SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる", "ﾊﾟﾈﾙ裏側", "組み合わせに注意(F側･R側)", "SWITCH は1工程前準備より貰い受ける事", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "SW部の凹型とｶﾊﾞｰ部の凸型を合わせる", "SW部とｶﾊﾞｰ部の隙間が均等にする" ], "Tolks": [ "締付ﾄﾙｸ 125cN･m", "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:1.F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:2.R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "125cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5255", "WorkName": "操作ﾊﾟﾈﾙSW組立2", "WorkItems": [ "■1. ①②にPANEL SWITCH を取付" ], "WorkPoints": [ "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "SW部", "取付けﾘﾝｸﾞ", "SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる", "ﾊﾟﾈﾙ裏側", "組み合わせに注意(F側･R側)", "SWITCH は1工程前準備より貰い受ける事", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "SW部の凹型とｶﾊﾞｰ部の凸型を合わせる", "SW部とｶﾊﾞｰ部の隙間が均等にする" ], "Tolks": [ "締付ﾄﾙｸ 125cN･m", "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:1.F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:2.R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "FM-5255", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "FM-5255専用ﾋﾞｯﾄ", "ToolOther": "147cN･m", "WorkName": "操作ﾊﾟﾈﾙSW組立2", "WorkItems": [ "■1. ①②にPANEL SWITCH を取付" ], "WorkPoints": [ "回り止め金具", "取付けﾘﾝｸﾞ", "SW部", "SW部", "取付けﾘﾝｸﾞ", "SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる", "ﾊﾟﾈﾙ裏側", "組み合わせに注意(F側･R側)", "SWITCH は1工程前準備より貰い受ける事", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "SW部の凹型とｶﾊﾞｰ部の凸型を合わせる", "SW部とｶﾊﾞｰ部の隙間が均等にする" ], "Tolks": [ "締付ﾄﾙｸ 125cN･m", "締付ﾄﾙｸ 147cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:1.F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "検査表①:2.R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "147cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "操作ﾊﾟﾈﾙSW配線処理", "WorkItems": [ "1. ①②にOPERATION PARTS WIRING: NPM-GH を接続しｲﾝｼｭﾛｯｸで固定" ], "WorkPoints": [ "STOP", "EXCH", "SERVO", "START", "ｺﾈｸﾀﾌﾞﾗｹｯﾄに取付ける", "F側､R側に区別されているので注意", "START､STOP､SERVO", "EXCH L ､EXCH R" ], "Tolks": [], "InspectionNo": "WEPJ-G002-D06", "InspectionItems": [ "検査表①:F-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:R-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認", "検査表②:R側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認", "検査表②:F側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認", "WEPJ-G002-D06" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WEPJ-G002-D06", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FAN組立1", "WorkItems": [ "■1. FAN の型式ﾁｪｯｸをし､ｼﾘｱﾙNo.を検査表に記入", "2. 1完成品にFAN-GUARD をSPACER BOLT WASHER WASHER で取付" ], "WorkPoints": [ "型式確認", "ｼﾘｱﾙ確認", "F側､R側に区別しておく", "ﾌｧﾝｶﾞｰﾄﾞの取付方向に注意すること", "風向き方向を確認して取付" ], "Tolks": [ "締付ﾄﾙｸ 152cN･m" ], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [ "検査表FAN :4.冷却FANの型式確認とｼﾘｱﾙNo.記録" ], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作", "WEPJ-G002-C11" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "152cN･m", "WorkName": "FAN組立1", "WorkItems": [ "■1. FAN の型式ﾁｪｯｸをし､ｼﾘｱﾙNo.を検査表に記入", "2. 1完成品にFAN-GUARD をSPACER BOLT WASHER WASHER で取付" ], "WorkPoints": [ "型式確認", "ｼﾘｱﾙ確認", "F側､R側に区別しておく", "ﾌｧﾝｶﾞｰﾄﾞの取付方向に注意すること", "風向き方向を確認して取付" ], "Tolks": [ "締付ﾄﾙｸ 152cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表FAN :4.冷却FANの型式確認とｼﾘｱﾙNo.記録", "この作業では同じものを2個製作", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "152cN･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FAN組立2", "WorkItems": [ "1. LABEL 【G103R】【G104R】を①②の配線に取付ける" ], "WorkPoints": [ "Front用【G103R】", "Rear用【G104R】", "ﾀｸﾞの端面と保護ﾁｭｰﾌﾞの端面を合わせて固定", "文字はGがﾁｭｰﾌﾞ端面側", "LABELはB1工程前準備より貰いうける事", "組み合わせに注意(F側･R側)", "Front用FANに【G103R】､Rear用FANに【G104R】を取付ける" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "G103R", "G103R", "G104R" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "FAN組立3", "WorkItems": [ "1. ①にCOVER をBOLT WASHER で取付" ], "WorkPoints": [ "取付方向に注意する事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "FAN組立3", "WorkItems": [ "2. CATCH をBRACKET にBOLT で取付" ], "WorkPoints": [ "CATCH はﾍﾞｰｽ側を使用ﾎﾞﾃﾞｨ側は次作業で使用", "ﾒｽ側" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾛｯｸﾀｲﾄ", "Size": "", "ToolOther": "243", "WorkName": "FAN組立4", "WorkItems": [ "3. 2完成品にLABEL を貼付け" ], "WorkPoints": [ "接着剤塗布箇所" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:各1", "3㎜", "この作業では同じものを2個製作", "◆作業者安全作業" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "FAN組立4", "WorkItems": [ "3. 2完成品にLABEL を貼付け" ], "WorkPoints": [ "接着剤塗布箇所" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:各1", "3㎜", "この作業では同じものを2個製作", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "FAN組立4", "WorkItems": [ "◆1. COVER に②をNUT BOLT で取付", "2. 1完成品にBUSH BUSH を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "10㎜", "3㎜", "◆作業者安全作業", "6㎜", "6㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "FAN組立5", "WorkItems": [ "1. COVER にBRACKET をWASHER BOLT で取付", "2. 1完成品にCOVER をBOLT WASHER で仮止め" ], "WorkPoints": [ "面一で取付", "SD-A038963-047で本締め" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "FAN組立5", "WorkItems": [ "1. COVER にBRACKET をWASHER BOLT で取付", "2. 1完成品にCOVER をBOLT WASHER で仮止め" ], "WorkPoints": [ "面一で取付", "SD-A038963-047で本締め" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "Fan-FilterGuideAssemblyJig", "Size": "", "ToolOther": "FM-6317", "WorkName": "FAN組立5", "WorkItems": [ "1. COVER にBRACKET をWASHER BOLT で取付", "2. 1完成品にCOVER をBOLT WASHER で仮止め" ], "WorkPoints": [ "面一で取付", "SD-A038963-047で本締め" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6317", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "100cN･m", "WorkName": "FAN組立6", "WorkItems": [ "1. ①にPLATE をBOLT で取付", "3. 2完成品にCOVER COVER COVER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "FAN組立6", "WorkItems": [ "2. 1完成品にSPACER をBOLT WASHER で取付" ], "WorkPoints": [ "面一になるよう取付", "中心に取付" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "10㎜", "ToolOther": "", "WorkName": "FAN組立7", "WorkItems": [ "1. ①に②をBOLT WASHER で仮止め", "2. 1完成品に③をｾｯﾄし位置調整をする" ], "WorkPoints": [ "ﾌﾞﾛｯｸｹﾞｰｼﾞを置く" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付位置確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "作業指示通り出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "FAN組立7", "WorkItems": [ "1. ①に②をBOLT WASHER で仮止め", "2. 1完成品に③をｾｯﾄし位置調整をする" ], "WorkPoints": [ "ﾌﾞﾛｯｸｹﾞｰｼﾞを置く" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "FAN組立7", "WorkItems": [ "1. ①に②をBOLT WASHER で仮止め", "2. 1完成品に③をｾｯﾄし位置調整をする" ], "WorkPoints": [ "ﾌﾞﾛｯｸｹﾞｰｼﾞを置く" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "Fan-FilterGuideAssemblyJig", "Size": "", "ToolOther": "FM-6317", "WorkName": "FAN組立7", "WorkItems": [ "1. ①に②をBOLT WASHER で仮止め", "2. 1完成品に③をｾｯﾄし位置調整をする" ], "WorkPoints": [ "ﾌﾞﾛｯｸｹﾞｰｼﾞを置く", "平行", "③ｶﾊﾞｰを被せ調整", "調整後③ｶﾊﾞｰは外しておくこと" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6317", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾛｯｸﾀｲﾄ", "Size": "", "ToolOther": "243", "WorkName": "FAN組立8", "WorkItems": [ "▲1. ①にFAN-GUARD ④をBOLT WASHER WASHER WASHER で取付" ], "WorkPoints": [ "ﾌｧﾝｶﾞｰﾄﾞの方向に注意", "WASHER ﾎﾞﾙﾄに接着剤塗布" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:各1", "この作業では同じものを2個製作", "▲特殊作業" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "FAN組立8", "WorkItems": [ "▲1. ①にFAN-GUARD ④をBOLT WASHER WASHER WASHER で取付" ], "WorkPoints": [ "ﾌｧﾝｶﾞｰﾄﾞの方向に注意", "WASHER ﾎﾞﾙﾄに接着剤塗布" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:各1", "この作業では同じものを2個製作", "▲特殊作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立", "WorkItems": [ "2. BRACKET に1完成品をBOLT WASHER で取付", "■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入", "3. 2完成品にCABLE-SUPPORT を取付" ], "WorkPoints": [ "型式表示が上面になるように", "取付け方向注意" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "WEPJ-G002-C11", "InspectionItems": [ "検査表BRACKET :ｶｰﾄﾞﾘｰﾀﾞ型式確認" ], "WorkTypes": [], "Words": [ "WEPJ-G002-C11" ] }
{ "QualityItem": "型式確認･製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認、製造番号を転記", "Method": "目視", "RecordMethod": "WEPJ-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立", "WorkItems": [ "2. BRACKET に1完成品をBOLT WASHER で取付", "■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入", "3. 2完成品にCABLE-SUPPORT を取付" ], "WorkPoints": [ "型式表示が上面になるように", "取付け方向注意" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表BRACKET :ｶｰﾄﾞﾘｰﾀﾞ型式確認", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "100cN･m", "WorkName": "SDｶｰﾄﾞﾘｰﾀﾞ組立", "WorkItems": [ "2. BRACKET に1完成品をBOLT WASHER で取付", "■1. CARD-READER の型式確認､ｼﾘｱﾙNo.を検査表に記入", "3. 2完成品にCABLE-SUPPORT を取付" ], "WorkPoints": [ "型式表示が上面になるように", "取付け方向注意" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表BRACKET :ｶｰﾄﾞﾘｰﾀﾞ型式確認" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "A002・003ｶﾊﾞｰ組立", "WorkItems": [ "1. COVER COVER にBRACKET BRACKET をBOLT WASHER で取付", "2. 1完成品にCABLE-SUPPORT を取付" ], "WorkPoints": [ "F側", "R側", "矢印方向に押し当て取付", "端面を合わせて取付" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "27㎜", "ToolOther": "3.5N･m", "WorkName": "A002・003ｶﾊﾞｰ組立(配線ﾌﾞﾗｹｯﾄ)", "WorkItems": [ "1. ①②にSIGNAL-TOWER を取付" ], "WorkPoints": [ "正面からｼｰﾙが見えないように取付", "ﾊﾟｯｷﾝはｶﾊﾞｰ表面側", "ﾜｯｼｬｰはｶﾊﾞｰ裏面側" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "160cN･m", "WorkName": "A002・003ｶﾊﾞｰ組立(FAN)1", "WorkItems": [ "1. ①②に③④をSCREW で取付", "2. 1完成品の配線をｲﾝｼｭﾛｯｸで固定" ], "WorkPoints": [ "FAN取付け方向に注意", "組み合わせに注意(F側･R側)", "FAN取付け方向", "板金が前を向くこと" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "160cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A002・003ｶﾊﾞｰ組立(FAN)1", "WorkItems": [], "WorkPoints": [ "長いｹｰﾌﾞﾙ(P2XXR)を1周させて､ｹｰﾌﾞﾙ先端ﾁｭｰﾌﾞを揃え､そこから30㎜で固定｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "30㎜", "30㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "A002・003ｶﾊﾞｰ組立(FAN)2", "WorkItems": [ "2. 1.完成品にBUSH を取付", "1. ①②に③④をBOLT WASHER で取付" ], "WorkPoints": [ "組み合わせに注意(F側･R側)" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A002・003ｶﾊﾞｰ組立(FAN)2", "WorkItems": [ "2. 1.完成品にBUSH を取付", "1. ①②に③④をBOLT WASHER で取付" ], "WorkPoints": [ "組み合わせに注意(F側･R側)" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "A002ｶﾊﾞｰ組立(SD)", "WorkItems": [ "1. ①に②BUSH をBOLT WASHER WASHER で取付" ], "WorkPoints": [ "カバー開口部中心に㉘を差込み抜き差し確認を行う", "取付け詳細", "BUSHの方向は凸が内向きになるように", "F側のみ使用" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)", "WorkItems": [ "1. ①COVER に③をBOLT WASHER で取付", "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.6N･m", "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)", "WorkItems": [], "WorkPoints": [ "取付け位置", "目安:3㎜", "横向き方向の長穴を取付け面にする", "取付け位置" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm", "16.5mm" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A002・004ｶﾊﾞｰ組立(開閉扉ｽﾄｯﾊﾟｰ)", "WorkItems": [ "1. ①COVER に③をBOLT WASHER で取付", "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け位置", "目安:3㎜", "横向き方向の長穴を取付け面にする", "取付け位置" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m", "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm", "16.5mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A002ｶﾊﾞｰ銘板貼付け1", "WorkItems": [ "1. ①にLABEL を貼付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "51.5mm", "122mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "A002ｶﾊﾞｰ銘板貼付け2", "WorkItems": [ "2. 1.完成品にLABEL LABEL 貼付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "35mm", "103mm", "141.5mm", "5mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾌｨｰﾀﾞ仕様", "WorkItems": [ "1. ①COVER に③をBOLT WASHER で取付" ], "WorkPoints": [ "取付け位置", "取付け位置" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾌｨｰﾀﾞ仕様", "WorkItems": [ "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け方向注意", "取付け位置", "目安:3㎜", "折り曲げ面より", "横向き方向の長穴を取付け面にする" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "16.5mm" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾌｨｰﾀﾞ仕様", "WorkItems": [ "1. ①COVER に③をBOLT WASHER で取付", "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け位置", "取付け位置", "取付け方向注意", "取付け位置", "目安:3㎜", "折り曲げ面より", "横向き方向の長穴を取付け面にする" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm", "16.5mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾄﾚｲ仕様", "WorkItems": [ "1. ①COVER にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け位置に注意", "取付け位置" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾄﾚｲ仕様", "WorkItems": [ "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け方向注意", "取付け位置", "目安:3㎜", "折り曲げ面より", "横向き方向の長穴を取付け面にする" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "16.5mm" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "A003・A005組立(開閉扉ｽﾄｯﾊﾟｰ)ﾄﾚｲ仕様", "WorkItems": [ "1. ①COVER にBRACKET をBOLT WASHER で取付", "2. 1完成品にBRACKET をBOLT WASHER で取付" ], "WorkPoints": [ "取付け位置に注意", "取付け位置", "取付け方向注意", "取付け位置", "目安:3㎜", "折り曲げ面より", "横向き方向の長穴を取付け面にする" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "7mm", "7.5mm", "16.5mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null