input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "0.8N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "振れ量:0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"振れ量:0.03㎜以内",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "振れ量:0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"振れ量:0.03㎜以内",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"振れ量:0.03㎜以内",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑩(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①を脱落防止ﾈｼﾞ(6箇所)で取付ける"
],
"WorkPoints": [
"脱落防止ﾈｼﾞ",
"PCｶﾊﾞｰにｷｽﾞ等無き事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "OP:左側延長ｺﾝﾍﾞﾔｰ組立⑩(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①を脱落防止ﾈｼﾞ(6箇所)で取付ける"
],
"WorkPoints": [
"脱落防止ﾈｼﾞ",
"PCｶﾊﾞｰにｷｽﾞ等無き事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "架台ﾚﾍﾞﾙの確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-A01"
]
} | {
"QualityItem": "ﾚﾍﾞﾙ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.06㎜/m以下",
"Method": "水準器",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6693",
"WorkName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ取り外し(ﾘｱ)",
"WorkItems": [
"1. Y軸ｽﾄｯﾊﾟｰ治具(FM-6693)を取り外す"
],
"WorkPoints": [
"Ｒ側のＹ軸リニアスライダーから㉖を取り外す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"マグネットに注意して㉖を取り外しする事",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取り外し確認",
"ToolManageNo": "FM-6693",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取り外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [
"■1. SWITCH の型式確認しﾛｯﾄNo.を記録",
"3. COVER に2完成品をBOLT WASHER で取付",
"2. BRACKET にSWITCH をBOLT で取付"
],
"WorkPoints": [
"ﾛｯﾄNo.",
"型式",
"ﾛｯﾄNo.",
"型式",
"ﾌｨｰﾀﾞｶﾊﾞｰ用",
"開閉ｶﾊﾞｰ用",
"▲印の方向に注意",
"矢印方向に当てつけ",
"この工程ではﾌｨｰﾀﾞｶﾊﾞｰ用SWのみ使用開閉ｶﾊﾞｰ用SWは開閉ｶﾊﾞｰ組立で使用",
"F側とR側に区別をしておくこと",
"貼付け位置",
"検査書記載後ﾏｽｷﾝｸﾞﾃｰﾌﾟに型式とﾛｯﾄNoを記載しCOVER に貼付け"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEPJ-G002-C11",
"InspectionItems": [
"検査表COVER :1.安全SWの型式とﾛｯﾄNoを記録"
],
"WorkTypes": [],
"Words": [
"1mm",
"取付け方向に注意!この部品には方向性があります",
"WEPJ-G002-C11"
]
} | {
"QualityItem": "型式･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "安全SW組立",
"WorkItems": [
"3. COVER に2完成品をBOLT WASHER で取付",
"2. BRACKET にSWITCH をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20",
"ToolOther": "194cN･m",
"WorkName": "安全SW組立",
"WorkItems": [
"3. COVER に2完成品をBOLT WASHER で取付",
"2. BRACKET にSWITCH をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [
"3. COVER に2完成品をBOLT WASHER で取付",
"2. BRACKET にSWITCH をBOLT で取付",
"3. COVER に2完成品をBOLT WASHER で取付",
"2. BRACKET にSWITCH をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"■安全作業",
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立1",
"WorkItems": [
"1. COVER にRUBBER-CUSHION を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "圧入台",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立2",
"WorkItems": [
"1. ①と②をSCREW で取付",
"2. 1完成品にLABEL を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm",
"50mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立2",
"WorkItems": [
"1. ①と②をSCREW で取付",
"2. 1完成品にLABEL を取付",
"1. ①と②をSCREW で取付",
"2. 1完成品にLABEL を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm",
"50mm",
"1mm",
"50mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "6.9㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立2",
"WorkItems": [
"1. ①と②をSCREW で取付",
"2. 1完成品にLABEL を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm",
"50mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "6.9㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ﾌｨｰﾀﾞｰｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6869",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立2",
"WorkItems": [
"1. ①と②をSCREW で取付",
"2. 1完成品にLABEL を取付"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞを挟んで取付け"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6.9mm",
"1mm",
"50mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6869",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立3",
"WorkItems": [
"1. BRACKET BRACKET にRUBBER-CUSHION を取付",
"2. ①に1完成品をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"37mm",
"20mm",
"37mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立3",
"WorkItems": [
"1. BRACKET BRACKET にRUBBER-CUSHION を取付",
"2. ①に1完成品をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"37mm",
"20mm",
"37mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ組立4",
"WorkItems": [
"1. PLATE にCOVER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "右側面組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1",
"両面全体にｸﾞﾘｰｽを塗布",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "194cN･m",
"WorkName": "右側面組立1",
"WorkItems": [
"2. BRACKET に1完成品を取付",
"◆1. PIN COLLAR にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢印面全体にｸﾞﾘｰｽを塗布",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "右側面組立2",
"WorkItems": [
"2. 1完成品にSPACER をWASHER NUT BOLT を取付",
"1. COVER にSTOPPER をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "右側面組立2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm",
"69mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側面組立2",
"WorkItems": [
"2. 1完成品にSPACER をWASHER NUT BOLT を取付",
"1. COVER にSTOPPER をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "右側面組立3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付",
"3. 2完成品にSPRING を取付",
"2. 1完成品に③をWASHER BOLT で取付"
],
"WorkPoints": [
"垂直になるように固定"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "右側面組立4",
"WorkItems": [
"1. BRACKET にBOLT NUT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側面組立4",
"WorkItems": [
"2. 1完成品にCOVER をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "右側面組立4",
"WorkItems": [
"3. 2完成品にBOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "右側面組立4",
"WorkItems": [
"3. 2完成品にBOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6066",
"WorkName": "右側面組立5",
"WorkItems": [
"1. ㉖のパーツを外し、指定の場所を緩める",
"2. ①を㉖に固定する",
"1. ㉖のパーツを外し、指定の場所を緩める",
"2. ①を㉖に固定する"
],
"WorkPoints": [
"3箇所で1完成品を固定する",
"3箇所で1完成品を固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6066",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6066",
"WorkName": "右側面組立6",
"WorkItems": [
"1. ①にｼﾞｸﾞﾊﾟｰﾂを置きSLIDE-PACK をSCREW で仮付け",
"2. ｼﾞｸﾞﾊﾟｰﾂを取付けSLIDE-PACK を位置決めし本締め",
"1. ①にｼﾞｸﾞﾊﾟｰﾂを置きSLIDE-PACK をSCREW で仮付け",
"2. ｼﾞｸﾞﾊﾟｰﾂを取付けSLIDE-PACK を位置決めし本締め",
"1. ①にｼﾞｸﾞﾊﾟｰﾂを置きSLIDE-PACK をSCREW で仮付け",
"2. ｼﾞｸﾞﾊﾟｰﾂを取付けSLIDE-PACK を位置決めし本締め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6066",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側面組立6",
"WorkItems": [
"1. ①にｼﾞｸﾞﾊﾟｰﾂを置きSLIDE-PACK をSCREW で仮付け",
"2. ｼﾞｸﾞﾊﾟｰﾂを取付けSLIDE-PACK を位置決めし本締め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6066",
"WorkName": "右側面組立7",
"WorkItems": [
"1. ①に②をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6066",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側面組立7",
"WorkItems": [
"1. ①に②をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6066",
"WorkName": "右側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝ位置を調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ピンク線部分に㉛が入らず フックが動くこと事",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6066",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ用ｶﾗｰ組立ｼﾞｸﾞ(右側)",
"Size": "",
"ToolOther": "FM-6103",
"WorkName": "右側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝ位置を調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ピンク線部分に㉛が入らず フックが動くこと事",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6103",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "右側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝ位置を調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ピンク線部分に㉛が入らず フックが動くこと事",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "右側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝ位置を調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ピンク線部分に㉛が入らず フックが動くこと事",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "左側面組立1",
"WorkItems": [
"◆1. PIN COLLAR にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1",
"矢印面全体にｸﾞﾘｰｽを塗布",
"両面全体にｸﾞﾘｰｽを塗布",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "194cN･m",
"WorkName": "左側面組立1",
"WorkItems": [
"2. BRACKET に1完成品を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "60cN･m",
"WorkName": "左側面組立2",
"WorkItems": [
"3. 2完成品にDOG をBOLT WASHER で取付",
"1. COVER にSTOPPER をSCREW WASHER で取付",
"2. 1完成品にSPACER をWASHER NUT BOLT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "左側面組立2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"69mm",
"1mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側面組立2",
"WorkItems": [
"3. 2完成品にDOG をBOLT WASHER で取付",
"1. COVER にSTOPPER をSCREW WASHER で取付",
"2. 1完成品にSPACER をWASHER NUT BOLT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "95cN･m",
"WorkName": "左側面組立2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"69mm",
"1mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "左側面組立3",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付",
"2. 1完成品に③をWASHER BOLT で取付",
"1. ①にBRACKET をBOLT WASHER で取付",
"2. 1完成品に③をWASHER BOLT で取付"
],
"WorkPoints": [
"垂直になるように固定",
"垂直になるように固定"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "左側面組立4",
"WorkItems": [
"1. BRACKET にBOLT NUT を取付",
"2. 1完成品にCOVER をSCREW で取付",
"3. 2完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左側面組立4",
"WorkItems": [
"1. BRACKET にBOLT NUT を取付",
"2. 1完成品にCOVER をSCREW で取付",
"3. 2完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "左側面組立4",
"WorkItems": [
"1. BRACKET にBOLT NUT を取付",
"2. 1完成品にCOVER をSCREW で取付",
"3. 2完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "左側面組立4",
"WorkItems": [
"◆4. COVER SCREW 全面にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "FM-6077ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(左側)",
"Size": "",
"ToolOther": "FM-6077",
"WorkName": "左側面組立5",
"WorkItems": [
"1. ㉖のパーツを外し、指定の場所を緩める",
"1. ㉖のパーツを外し、指定の場所を緩める"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6077",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "FM-6077ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(左側)",
"Size": "",
"ToolOther": "FM-6077",
"WorkName": "左側面組立6",
"WorkItems": [
"2. ｼﾞｸﾞﾊﾟｰﾂを取付けSLIDE-PACK を位置決めし本締め",
"1. ①にｼﾞｸﾞﾊﾟｰﾂを置きSLIDE-PACK をSCREW で仮付け",
"3. ｽﾗｲﾄﾞﾌﾞﾛｯｸを図のような位置にして次のｼﾞｸﾞﾊﾟｰﾂを取付",
"3. ｽﾗｲﾄﾞﾌﾞﾛｯｸを図のような位置にして次のｼﾞｸﾞﾊﾟｰﾂを取付"
],
"WorkPoints": [
"SLIDE-PACK を矢印方向に押し当て",
"SLIDE-PACK を矢印方向にｼﾞｸﾞﾊﾟｰﾂのﾉﾌﾞを回して押し当て",
"Dﾋﾟﾝとﾉﾌﾞでｼﾞｸﾞﾊﾟｰﾂを挟み込み位置決めする",
"矢印方向にｼﾞｸﾞﾊﾟｰﾂ押し当て",
"SLIDE-PACK を矢印方向に押し当て",
"SLIDE-PACK を矢印方向にｼﾞｸﾞﾊﾟｰﾂのﾉﾌﾞを回して押し当て",
"Dﾋﾟﾝとﾉﾌﾞでｼﾞｸﾞﾊﾟｰﾂを挟み込み位置決めする",
"矢印方向にｼﾞｸﾞﾊﾟｰﾂ押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6077",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左側面組立6",
"WorkItems": [
"3. ｽﾗｲﾄﾞﾌﾞﾛｯｸを図のような位置にして次のｼﾞｸﾞﾊﾟｰﾂを取付"
],
"WorkPoints": [
"SLIDE-PACK を矢印方向に押し当て",
"SLIDE-PACK を矢印方向にｼﾞｸﾞﾊﾟｰﾂのﾉﾌﾞを回して押し当て",
"Dﾋﾟﾝとﾉﾌﾞでｼﾞｸﾞﾊﾟｰﾂを挟み込み位置決めする",
"矢印方向にｼﾞｸﾞﾊﾟｰﾂ押し当て"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "FM-6077ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(左側)",
"Size": "",
"ToolOther": "FM-6077",
"WorkName": "左側面組立7",
"WorkItems": [
"1. ①に②をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6077",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左側面組立7",
"WorkItems": [
"1. ①に②をSCREW WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "FM-6077ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ組立ｼﾞｸﾞ(左側)",
"Size": "",
"ToolOther": "FM-6077",
"WorkName": "左側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝを調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ",
"ピンク線部分に㉛が入らず フックが動くこと事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6077",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰﾃｰﾌﾞﾙｶﾊﾞｰ用ｶﾗｰ組立ｼﾞｸﾞ(左側)",
"Size": "",
"ToolOther": "FM-6111",
"WorkName": "左側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝを調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ",
"ピンク線部分に㉛が入らず フックが動くこと事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6111",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "左側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝを調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ",
"ピンク線部分に㉛が入らず フックが動くこと事"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "左側面組立8",
"WorkItems": [
"1. ①のﾋﾟﾝを調整",
"2. ｼﾞｸﾞﾊﾟｰﾂ①②③④⑤の順にｼﾞｸﾞを外す"
],
"WorkPoints": [
"・ピンとブラケットの間に㉙をセットする・㉙のねじを回してピンを押し、フックとの隙間を無くす",
"ｼﾞｸﾞﾊﾟｰﾂ④",
"ｼﾞｸﾞﾊﾟｰﾂ③",
"ｼﾞｸﾞﾊﾟｰﾂ①",
"ｼﾞｸﾞﾊﾟｰﾂ②",
"ｼﾞｸﾞﾊﾟｰﾂ⑤",
"㉖を起こして作業する"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾋﾟﾝ",
"ﾌｯｸ",
"ﾌﾞﾗｹｯﾄ",
"ねじ",
"ピンク線部分に㉛が入らず フックが動くこと事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ﾌｨｰﾀﾞｰｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6869",
"WorkName": "ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰ銘板貼付(F側)",
"WorkItems": [
"1. COVER を脱脂しLABEL LABEL を貼付"
],
"WorkPoints": [
"COVER を真上から見た図",
"【Fﾌｨｰﾀﾞ】となっている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"257mm",
"20mm",
"25mm",
"60mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6869",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ﾌｨｰﾀﾞｰｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6869",
"WorkName": "識別ﾗﾍﾞﾙ貼付け17連/34連(前側)",
"WorkItems": [
"1. ①を脱脂し㉗を取付けLABEL を貼付ける"
],
"WorkPoints": [
"㉗大を取付け㉗小を取付け後LABEL を左詰めで貼る",
"Rのはじめに合わせる",
"裏面㉗段差部を①に当付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6869",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ﾌｨｰﾀﾞｰｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6869",
"WorkName": "識別ﾗﾍﾞﾙ貼付け40連(前側)",
"WorkItems": [
"1. ①を脱脂し㉗を取付けLABEL を貼付ける"
],
"WorkPoints": [
"Rのはじめに合わせる",
"裏面㉗段差部を①に当付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6869",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品(F側)",
"WorkItems": [
"1. COVER PLATE ③SCREW SCREW SCREW を次工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立1",
"WorkItems": [
"3. 1完成品を2完成品に取付",
"2. FRAME にCABLE-SUPPORT を取付",
"1. NUT にCAP を取付"
],
"WorkPoints": [
"ｹｰﾌﾞﾙｸﾗﾝﾌﾟを挿入後90度回転させ固定",
"表面",
"裏面",
"1完成品は表面が上になるように取付",
"ｷｬｯﾌﾟ取付方向に注意する事",
"ｹｰﾌﾞﾙｻﾎﾟｰﾄは先に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M6",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. NUT NUT NUT にCAP を取付",
"2. 1完成品を①に取付"
],
"WorkPoints": [
"右側",
"左側",
"右側",
"B\t面",
"表面",
"裏面",
"ｷｬｯﾌﾟ取付方向に注意する事",
"1完成品は表面が上になるように取付",
"ｻｲｽﾞが異なるので注意",
"左側",
"A面",
"右側",
"左側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M4",
"M6",
"M6",
"M6",
"M6",
"M4",
"M6",
"M6",
"M6",
"M6",
"M6",
"M6",
"M4",
"M6",
"M5",
"M6",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.2㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示通り出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)1",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"端面に合わせる",
"面を合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"矢印方向に押当",
"左右で取付け位置が異なるので注意"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"矢印方向に押当",
"左右で取付け位置が異なるので注意"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)3",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右で取付け位置が異なることに注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)4",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"右側組立のみ取付(左側組立は取付なし)",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)5",
"WorkItems": [
"1. ①にCOVER を取付"
],
"WorkPoints": [
"右側組立のみ取付(左側組立は取付なし)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"35㎜",
"35㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)6",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)1",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"端面に合わせる",
"面を合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右で取付け位置が異なるので注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右で取付け位置が異なるので注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)3",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右組立で取付け位置が異なることに注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)4",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"左右組立で取付け位置､個数が異なることに注意",
"外面に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890",
"★→0~0.75㎜程度隙間を開ける",
"Line A,Bは端面より貼付",
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890",
"★→0~0.75㎜程度隙間を開ける",
"Line A,Bは端面より貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"19mm",
"この作業では同じものを2個製作",
"450㎜",
"50㎜",
"50㎜",
"50㎜",
"50㎜",
"100㎜",
"100㎜",
"19mm",
"この作業では同じものを2個製作",
"450㎜",
"50㎜",
"50㎜",
"50㎜",
"50㎜",
"100㎜",
"100㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5.5M",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890",
"★→0~0.75㎜程度隙間を開ける",
"Line A,Bは端面より貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"19mm",
"この作業では同じものを2個製作",
"450㎜",
"50㎜",
"50㎜",
"50㎜",
"50㎜",
"100㎜",
"100㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890",
"★→0~0.75㎜程度隙間を開ける",
"Line A,Bは端面より貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"19mm",
"この作業では同じものを2個製作",
"450㎜",
"50㎜",
"50㎜",
"50㎜",
"50㎜",
"100㎜",
"100㎜"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [],
"WorkPoints": [
"Line A",
"Line B",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"FM-5890"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"26mm",
"16mm",
"5mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂"
],
"WorkPoints": [
"Line A",
"Line B",
"片面のみ実施※裏表関係なし",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"FM-5890",
"青線枠を脱脂"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"26mm",
"16mm",
"5mm",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [],
"WorkPoints": [
"Line A",
"Line B",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"FM-5890"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"26mm",
"16mm",
"5mm"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [
"1. TAPE を一本 140mmの長さに切る",
"2. COVER を脱脂し､1完成品を貼付､圧着する(2往復)",
"3. COVER を脱脂し､TAPE を貼付け圧着"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"両面ﾃｰﾌﾟ貼付け面に注意",
"貼付け面",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"140mm",
"この作業では同じものを2個製作",
"185mm",
"6mm",
"20mm",
"20mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [
"1. TAPE を一本 140mmの長さに切る",
"2. COVER を脱脂し､1完成品を貼付､圧着する(2往復)",
"3. COVER を脱脂し､TAPE を貼付け圧着"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"両面ﾃｰﾌﾟ貼付け面に注意",
"貼付け面",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"140mm",
"185mm",
"6mm",
"20mm",
"20mm",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [
"3. COVER を脱脂し､TAPE を貼付け圧着"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復する",
"貼付け面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"185mm",
"6mm",
"20mm",
"20mm"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"1. COVER COVER TAPE を脱脂しTAPE を貼付け圧着"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4mm",
"2mm",
"20mm",
"20mm",
"この作業では同じものを2個製作",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"1. COVER COVER TAPE を脱脂しTAPE を貼付け圧着"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4mm",
"2mm",
"20mm",
"20mm",
"この作業では同じものを2個製作",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"1. COVER COVER TAPE を脱脂しTAPE を貼付け圧着"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4mm",
"2mm",
"20mm",
"20mm",
"この作業では同じものを2個製作",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立1",
"WorkItems": [
"1. FRAME にBRACKET をBOLT WASHER で仮締め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"仮止め:SD-A038963-021にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②を①に貼付",
"3. ①のアクリルシートをめくり㉙でとめ、脱脂",
"4. COVER にTAPE を貼付ける"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"矢印方向に当てつけ",
"貼付け後､手で仮圧着",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす",
"治具番号1",
"治具番号1",
"圧着ﾛｰﾗｰで2往復",
"2本",
"2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"15㎜",
"50㎜",
"70㎜",
"50㎜",
"50㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5.5M",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"3. ①のアクリルシートをめくり㉙でとめ、脱脂",
"4. COVER にTAPE を貼付ける"
],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"2本",
"2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"15㎜",
"50㎜",
"70㎜",
"50㎜",
"50㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GH用扉組立台",
"Size": "",
"ToolOther": "FM-5804",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. 治具作業台に①をｾｯﾄし､専用治具を取付け脱脂",
"2. ②を①に貼付"
],
"WorkPoints": [
"FM-5804",
"FM-5804",
"矢印方向に当てつけ",
"貼付け後､手で仮圧着",
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす",
"治具番号1",
"治具番号1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5804",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.