text stringlengths 1 2.97k |
|---|
> |
> ------------------------------ |
> *From:* labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of James |
> Mitchell <jtmitch5 at ncsu.edu> |
> *Sent:* 22 March 2023 18:29 |
> *To:* Fab Network <labnetwork at mtl.mit.edu> |
> *Subject:* [labnetwork] Suss MA6 Question |
> |
> |
> ? Caution: External sender |
> |
> Lamp power supply will not turn on after lamp failure. |
> We had a lamp (350 W) pop on our system. |
> Cleaned up and installed a new lamp. |
> When we start the power supply the breaker in the back of the system trips. |
> Specifically, it trips when we press CP. System starts at STAND-BY. |
> Press "ON" and the display shows "READY". Press CP and it displays |
> "Wait..." for a second and then trips. |
> We checked for shorts and all looked good. We swapped to the other 220 |
> Volt plug in the back and it trips as well. |
> Any ideas on this? We are not sure if the start box or the supply |
> itself is the issue. |
> |
> |
> *Thank you, Jim* |
> |
> *James Mitchell* |
> *Specialty Trades Technician* |
> *Dept. of Electrical and Computer Engineering* |
> *North Carolina State University Nanofabrication Facility (NNF)* |
> *MRC RM243A **Box 7911* |
> *2410 Campus Shore Dr., Raleigh, NC 27606* |
> *jtmitch5 at ncsu.edu* <jtmitch5 at ncsu.edu> |
> *Desk: 919-515-5394* |
> *Cell: 919-717-7325* |
> |
> |
> |
-- |
*Thank you, Jim* |
*James Mitchell* |
*Specialty Trades Technician* |
*Dept. of Electrical and Computer Engineering* |
*North Carolina State University Nanofabrication Facility (NNF)* |
*MRC RM243A **Box 7911* |
*2410 Campus Shore Dr., Raleigh, NC 27606* |
*jtmitch5 at ncsu.edu* <jtmitch5 at ncsu.edu> |
*Desk: 919-515-5394* |
*Cell: 919-717-7325* |
-------------- next part -------------- |
An HTML attachment was scrubbed... |
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20230323/8d4df581/attachment.html> |
-------------- next part -------------- |
A non-text attachment was scrubbed... |
Name: 20230323_075350.jpg |
Type: image/jpeg |
Size: 2060183 bytes |
Desc: not available |
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20230323/8d4df581/attachment.jpg> |
From r.khanna at ucl.ac.uk Thu Mar 23 08:31:49 2023 |
From: r.khanna at ucl.ac.uk (Khanna, Rohit) |
Date: Thu, 23 Mar 2023 12:31:49 +0000 |
Subject: [labnetwork] Suss MA6 Question |
In-Reply-To: <CAEXS_M-sXrRa_4z8MsZH-wh-OGgVHmi99j2uZ+4HH14RQ-_sPQ@mail.gmail.com> |
References: <CAEXS_M-9AfbQv1TzikGbZ_tLVdF4hf_O_rVA3Qh7wp2t4vXyKg@mail.gmail.com> |
<VI1PR01MB644654C5B77681F362CD0A1DC3879@VI1PR01MB6446.eurprd01.prod.exchangelabs.com> |
<CAEXS_M-sXrRa_4z8MsZH-wh-OGgVHmi99j2uZ+4HH14RQ-_sPQ@mail.gmail.com> |
Message-ID: <VI1PR01MB644652FD91984F97DA56E1C1C3879@VI1PR01MB6446.eurprd01.prod.exchangelabs.com> |
Hi James, |
Our unit was very similar to yours. Unfortunately, it's hard to get the schematics for these, however I can assure you these are very similar, and they are standard buck boost convertor or SEPIC convertors. The MOSFET and diodes are easy to spot as they are mounted on a big heat sink with thermal paste. |
Warm Regards |
Rohit Khanna |
Electronic Test & Measurement Engineer |
London Centre for NANO Technology, UCL |
Ph:+44-020-76799984 |
Lab: +44 20 3108 1516 |
Int Ext: 39984 |
________________________________ |
From: James Mitchell <jtmitch5 at ncsu.edu> |
Sent: 23 March 2023 12:18 |
To: Khanna, Rohit <r.khanna at ucl.ac.uk> |
Cc: Fab Network <labnetwork at mtl.mit.edu> |
Subject: Re: [labnetwork] Suss MA6 Question |
Thanks, we have the CIC1200. Do you have the schematics for this? |
[20230323_075350.jpg] |
On Thu, Mar 23, 2023 at 7:42?AM Khanna, Rohit <r.khanna at ucl.ac.uk<mailto:r.khanna at ucl.ac.uk>> wrote: |
Hi Mitchell, |
Could you put some images of the power supply along with the model number. We had a similar UV lamp power supply failure. I had to change the high power MOSFETS and diodes in the unit along with some PTC inrush current limiter. These lamp drivers are fairly advanced as they constantly monitor the power lamp power and lamp current. I had used the following components to get the supply up and running. Repairing this unit involves disassembling the complete power supply and do board level repairs. These parts were ordered from Mouser Electronics. |
494-APT2X61D60J Rectifiers Fast Recovery Epitaxial Diode - D |
494-APT5010JVRU2 Discrete Semiconductor Modules Power Module - Mosfet |
494-APT80M60J Discrete Semiconductor Modules Power MOSFET - MOS8 |
821-GBPC3510W Bridge Rectifiers 35A 1000V GLASS PASS WIRE |
995-MS32-20010 |
Inrush Current Limiters 32mm 20ohms 10A INRSH CURR LIMITER |
TC4420CPA |
MOSFET Driver Low Side, 4.5V-18V supply, 6A peak out, 2.1 Ohm output, DIP-8 |
Warm Regards |
Rohit Khanna |
Electronic Test & Measurement Engineer |
London Centre for NANO Technology, UCL |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.