hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.3.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.6.5.3.4.1-1.
Table 16.6.5.3.4.1-1: Supported test configurations
Configuration
Description
16.6.5.3-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode, LTE FDD
16.6.5.3-2
NR 15 kHz SSB SCS, 10 MHz bandwidth, TDD duplex mode, LTE FDD
16.6.5.3... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.3.4.2 Test procedure | Throughout the test, the UE shall be scheduled to perform DL reception on every slot suitable for DL.
1. Ensure the UE is in State RRC_CONNECTED with generic procedure parameters Connectivity NR, Connected without release On according to TS 38.508-1 [14] clause 4.5. Establish SRB2 and DRB in the RRC Reconfiguration mes... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.3.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 16.6.1.1.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Default RRC messages and information elements contents exceptions
Table H.3.1-1
Table 16.6.1.1.4.3... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.3.5 Test requirements | Table 16.6.5.3.4.1-3, Table 16.6.5.3.5-1 and Table 16.6.5.3.5-2 define the primary level settings including test tolerances for the test.
Table 16.6.5.3.5-3: NR cell specific test parameters (Cell 1)
Parameter
Unit
Configuration
Cell 1
T1
T2
T3
RF channel number
1,2,3,4,5,6
1
Duplex mode
1,4
FDD
2,3,5,6
TDD
TDD Configu... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4 NR SA FR1 - E-UTRA CGI Identification of E-UTRA cell for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.1 Test purpose | To verify the requirement for identification of a new CGI of E-UTRA cell with autonomous gaps in NR SA in TS 38.133 clause 9.4A.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards and supporting acquisition of CGI from neighbour E-UTRA cell using autonomous gap. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.6.5.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.6.5.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.4 Test description | Same as the test description given in clause 16.6.5.3.4 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.4.1 Initial conditions | Same as the initial conditions given in clause 16.6.5.3.4 with following exceptions:
- Table 16.6.5.3.4.1-1 is replaced by Table 16.6.5.4.4.1-1;
- Table 16.6.5.3.4.1-2 is replaced by Table 16.6.5.4.4.1-2;
- Table 16.6.5.3.4.1-3 is replaced by Table 16.6.5.4.4.1-3.
Table 16.6.5.4.4.1-1: Supported test configurations
Con... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.4.2 Test procedure | Same as the test procedure given in clause 16.6.5.3.4.2 with following exceptions:
- Step 12 in clause 16.6.5.3.4.2 is replaced by following step:
12. If the UE
a) transmits a MeasurementReport message containing CGI of E-UTRA Cell 2 less than 200 ms from the beginning of time period T3, and
b) transmits ACK/NACKs no l... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.4.3 Message contents | Same as the message contents given in clause 16.6.5.3.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.6.5.4.5 Test requirements | Table 16.6.5.4.4.1-3, Table 16.6.5.4.5-1 and Table 16.6.5.4.5-2 define the primary level settings including test tolerances for the test.
Table 16.6.5.4.5-3: NR cell specific test parameters (Cell 1)
Parameter
Unit
Configuration
Cell 1
T1
T2
T3
RF channel number
1,2,3,4,5,6
1
Duplex mode
1,4
FDD
2,3,5,6
TDD
TDD Configu... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7 Measurement performance requirements for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1 SS-RSRP for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.0.1 Intra-frequency absolute SS-RSRP measurement accuracy requirements | The accuracy requirements in clause 6.7.1.0.1 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.1.0.1-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensitivity are fulf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.0.2 Intra-frequency relative SS-RSRP measurement accuracy requirements | The accuracy requirements in clause 6.7.1.0.2 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.1.0.2-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensitivity are fulf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.0.3 Inter-frequency absolute SS-RSRP measurement accuracy requirements | The accuracy requirements in clause 6.7.1.0.3 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.1.0.3-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensitivity are fulf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.0.4 Inter-frequency relative SS-RSRP measurement accuracy requirements | The accuracy requirements in clause 6.7.1.0.4 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.1.0.4-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensitivity are fulf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1 Intra-frequency measurements for RedCap for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1 NR SA FR1 SS-RSRP absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.1.1.4.1-1.
Table 16.7.1.1.1.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.1.1-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.1.1-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.1.1.4.2 with following exceptions:
- Table 6.7.1.1.1.5-1 is replaced by Table 16.7.1.1.1.5-1.
- Table 6.7.1.1.1.5-2 is replaced by Table 16.7.1.1.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.4.3 Message contents | Same as the message contents given in clause 6.7.1.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.1.1-1 applies to test configuration 16.7.1.1.1-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.1.1.1-3 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.1.5 Test requirement | Table 16.7.1.1.1.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.1.1.5-1 shall meet the corresponding absolute accuracy requirements in Table 16.7.1.1.1.5-2 for test configurations 1, 2 and 4 and the corresponding abso... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2 NR SA FR1 SS-RSRP relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.1.2.4.1-1.
Table 16.7.1.1.2.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.1.2-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.1.2-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.1.2.4.2 with following exceptions:
- Table 6.7.1.1.2.5-1 is replaced by Table 16.7.1.1.2.5-1.
- Table 6.7.1.1.2.5-2 is replaced by Table 16.7.1.1.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.4.3 Message contents | Message contents are same as in clause 16.7.1.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.1.2.5 Test requirement | Table 16.7.1.1.2.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.1.2.5-1 shall meet the corresponding relative accuracy requirements in Table 16.7.1.1.2.5-2.
Table 16.7.1.1.2.5-1: Same as Table 16.7.1.1.1.5-1 with the ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2 Intra-frequency measurements for RedCap for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1 NR SA FR1 SS-RSRP absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.2.1.4.1-1.
Table 16.7.1.2.1.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.2.1-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.2.1-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.1.1.4.2 with following exceptions:
- Table 6.7.1.1.1.5-1 is replaced by Table 16.7.1.2.1.5-1.
- Table 6.7.1.1.1.5-2 is replaced by Table 16.7.1.2.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.4.3 Message contents | Same as the message contents given in clause 6.7.1.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.1.1-1 applies to test configuration 16.7.1.2.1-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.1.2.1-3 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.1.5 Test requirement | Table 16.7.1.2.1.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.2.1.5-1 shall meet the corresponding absolute accuracy requirements in Table 16.7.1.2.1.5-2 for test configurations 1, 2 and 4 and the corresponding abso... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2 NR SA FR1 SS-RSRP relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.2.2.4.1-1.
Table 16.7.1.2.2.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.2.2-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.2.2-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.1.2.4.2 with following exceptions:
- Table 6.7.1.1.2.5-1 is replaced by Table 16.7.1.2.2.5-1.
- Table 6.7.1.1.2.5-2 is replaced by Table 16.7.1.2.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.4.3 Message contents | Message contents are same as in clause 16.7.1.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.2.2.5 Test requirement | Table 16.7.1.2.2.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.2.2.5-1 shall meet the corresponding relative accuracy requirements in Table 16.7.1.2.2.5-2.
Table 16.7.1.2.2.5-1: Same as Table 16.7.1.2.1.5-1 with the ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3 Inter-frequency measurements for RedCap for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1 NR SA FR1-FR1 SS-RSRP absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.1 Test purpose | The purpose of this test is to verify that the inter-frequency SS-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.3.1.4.1-1.
Table 16.7.1.3.1.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.3.1-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.3.1-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.2.1.4.2 with following exceptions:
- Table 6.7.1.2.1.5-1 is replaced by Table 16.7.1.3.1.5-1.
- Table 6.7.1.2.1.5-2 is replaced by Table 16.7.1.3.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.4.3 Message contents | Same as the message contents given in clause 6.7.1.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.1.2.1-1 applies to test configuration 16.7.2.2-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.1.3.1-3 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.1.5 Test requirement | Table 16.7.1.3.1.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.3.1.5-1 shall meet the corresponding absolute accuracy requirements in Table 16.7.1.3.1.5-2 for test configurations 1, 2 and 4 and the corresponding abso... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2 NR SA FR1-FR1 SS-RSRP relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.1 Test purpose | The purpose of this test is to verify that the inter-frequency SS-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.4.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.3.2.4.1-1.
Table 16.7.1.3.2.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.3.2-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.3.2-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.2.2.4.2 with following exceptions:
- Table 6.7.1.2.2.5-1 is replaced by Table 16.7.1.3.2.5-1.
- Table 6.7.1.2.2.5-2 is replaced by Table 16.7.1.3.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.4.3 Message contents | Message contents are same as in clause 16.7.1.3.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.3.2.5 Test requirement | Table 16.7.1.3.2.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.3.2.5-1 shall meet the corresponding relative accuracy requirements in Table 16.7.1.3.2.5-2.
Table 16.7.1.3.2.5-1: Same as Table 16.7.1.3.1.5-1
Table 16.... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4 Inter-frequency measurements for RedCap for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1 NR SA FR1-FR1 SS-RSRP absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.1 Test purpose | The purpose of this test is to verify that the inter-frequency SS-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.4.1.4.1-1.
Table 16.7.1.4.1.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.4.1-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.4.1-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.2.1.4.2 with following exceptions:
- Table 6.7.1.2.1.5-1 is replaced by Table 16.7.1.4.1.5-1.
- Table 6.7.1.2.1.5-2 is replaced by Table 16.7.1.4.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.4.3 Message contents | Same as the message contents given in clause 6.7.1.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.1.2.1-1 applies to test configuration 16.7.1.4.1-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.1.4.1-3 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.1.5 Test requirement | Table 16.7.1.4.1.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.4.1.5-1 shall meet the corresponding absolute accuracy requirements in Table 16.7.1.4.1.5-2 for test configurations 1, 2 and 4 and the corresponding abso... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2 NR SA FR1-FR1 SS-RSRP relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.1 Test purpose | The purpose of this test is to verify that the inter-frequency SS-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.1.0.4.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 16.7.1.4.2.4.1-1.
Table 16.7.1.4.2.4.1-1: NR SA FR1 SS-RSRP measurement accuracy supported test configurations
Test Case ID
Description
16.7.1.4.2-1
NR 15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode
16.7.1.4.2-2
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.1.2.2.4.2 with following exceptions:
- Table 6.7.1.2.2.5-1 is replaced by Table 16.7.1.4.2.5-1.
- Table 6.7.1.2.2.5-2 is replaced by Table 16.7.1.4.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.4.3 Message contents | Message contents are same as in clause 16.7.1.4.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.1.4.2.5 Test requirement | Table 16.7.1.4.2.5-1 defines the primary level settings including test tolerances for all tests.
Each SS-RSRP measurement report for each of the tests in Table 16.7.1.4.2.5-1 shall meet the corresponding relative accuracy requirements in Table 16.7.1.4.2.5-2.
Table 16.7.1.4.2.5-1: Same as Table 16.7.1.4.1.5-1
Table 16.... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2 SS-RSRQ for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.0.1 Intra-frequency SS-RSRQ measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.2.0.1 shall apply.
When RedCap UE is only required to support 1Rx, the absolute accuracy requirements in Table 16.7.2.0.1-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensiti... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.0.2 Inter-frequency SS-RSRQ absolute measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.2.0.2 shall apply.
When RedCap UE is only required to support 1Rx, the absolute accuracy requirements in Table 16.7.2.0.2-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensit... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.